A solid-state electrochromic device based on complementary polypyrrole/polythiophene derivatives and an elastomeric electrolyte

A device was assembled using optically transparent glass electrodes and combining two complementary electrochromic polymeric materials, poly(4,4-dipentoxy-2,2-bithiophene) and poly(N,N-dimethyl-2,2-bipyrrole). As electrolyte we used an ionically conductive polymer; poly(epichlorohydrin-co-ethylene oxide) containing a lithium salt. The optical contrast in the visible/near infrared region, stability to repeated redox cycles and electrochromic efficiency are reported and discussed.     

Syntheses and properties of polyimides based on bis(p-aminophenoxy)biphenyls

Three biphenyl unit-containing diamines,4,4-bis(p-aminophenoxy)biphenyl (III_a), 2,2-bis(p-aminophenoxy)biphenyl (III_b), and 3,3,5,5-tetramethyl-4,4-bis(p-aminophenoxy)biphenyl (III_c), were prepared by the chlorodisplacement ofp-chloronitrobenzene with 4,4-biphenol (I_a), 2,2-biphenol (I_b), and 3,3,5,5-tetramethyl-4,4-biphenol (I_c), respectively, giving the corresponding bis(nitrophenoxy) compounds II_a-c, followed by catalytic reduction with palladium (Pd) and hydrazine. Three series of polyimidesp-PI,o-PI, and Me-PI were prepared from diamines III_a-c and aromatic tetracarboxylic dianhydrides via a two-stage procedure that included ring-opening polyaddition to give poly(amic acid)s followed by thermal cyclodehydration to polyimides. The resultant three series of poly(amic acid)s had inherent viscosities of 1.09–2.83, 0.78–1.93, and 1.55–3.09 dL/g, respectively. Almost all the poly(amic acid)s could be solution-cast and thermally converted into transparent, flexible, and tough polyimide films. All the polyimides were characterized by solubility, tensile test, wide-angle X-ray scattering measurements, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Effects of the structures of aromatic diamines and dianhydrides on the properties of polyimides were investigated.     

Synthesis of soluble polyarylenes containing alternating 4,4′-(1,1′-binaphthyl) and 4,4′-(3,3′-diphenyl)biphenyl structural units

Summary The synthesis and Ni(0) catalyzed homocoupling polymerization of 4,4-bis[5-(trifluoromethanesulfonyloxy)-2-biphenylyl]-1, 1-binaphthyl (9) are described. This polymerization reaction produces a soluble polyarylene containing alternating 4,4-(1,1-binaphthyl) and 4,4-(3,3-diphenyl)biphenyl structural units.     

Shape-selective isopropylation of biphenyl over a highly dealuminated mordenite: effect of propylene pressure

A highly dealuminated H-mordenite (H-M) catalyzed the selective isopropylation of biphenyl to 4,4-diisopropylbiphenyl (4,4-DIPB). The high selectivity is ascribed to the shape-selective catalysis in mordenite pores. The selectivity of 4,4-DIPB decreased during the isopropylation of biphenyl due to isomerization of 4,4-DIPB under low propylene pressure. The increase of propylene pressure suppressed the isomerization in the isopropylation. 4,4-DIPB itself was isomerized over highly dealuminated H-M under low propylene pressure.     

Thermotropic polyester: the influence of the spacer on the physical properties

Thermotropic polyesters prepared from series of 4,4-dihydroxy-,w-diphenoxy alkanes and 4,4-dichloroformyl-,w-diphenoxy alkanes are well known. The substitution of a methylenic spacer by an oxyethylenic spacer in the main chain of these polyesters drastically modifies their physical properties, particularly the mesogenic transition temperatures, as can be observed by DSC and thermooptical analysis. The thermal stability and the polymer solubility in common organic solvents of these polymers did not show a significant change. The physical properties of the two thermotropic polyesters prepared in diphenyl ether were evaluated.     

Synthesis of new metal-containing side-chain monomers and polymers

New metal-containing vinyl monomers, hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hexyl-6-oxy-{4-[4-(4-ferrocenoyl phenyl)phenyl]benzoyloxy}methacrylate, and the corresponding homopolymers and random copolymers with hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate were synthesized. The compounds were characterized by¹H NMR; their thermal behavior was investigated by means of differential scanning calorimetry. Monomers and polymers containing the ferrocene unit melt at lower temperatures than those derived from the cyclopentadienyl managanese tricarbonyl moiety. The melting temperatures of the monomers and polymers ranged from 399 to about 515 K, Both monomers and polymers failed to exhibit mesogenic behavior. Values ofM _n,M _w,M _w/M _n, and degree of polymerization were obtained by gel permeation chromatography. TheM _n ranged from 16,500 for the copolymer containing hexyl-6-oxy-{4-[4-(4-ferrocenoyl phenyl)phenyl] benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio to 26,000 for the copolymer containing hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio.M _w/M _n ranged from 1.6 in the case of the copolymer containing hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio to 2.2 in the case of poly(hexyl-6-oxy{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate).     

Preparation of poly(alkylvinylether)s for nonlinear optical applications

Summary 3,5-Dimethoxy-4-(2-vinyloxyethoxy)-4-nitrostilbene 2 and 3,5-dimethoxy-4-(2-vinyloxyethoxy)-2,4-dinitrostilbene 5 were prepared by the reactions of 2-iodoethyl vinyl ether with 3,5-dimethoxy-4-hydroxy-4-dinitrostilbene 1 and 3,5-dimethoxy-4-hydroxy-2,4-dinitrostilbene 4, respectively. Monomers 2 and 5 were polymerized with cationic initiators to obtain polymers with the NLO-phores 3,5-dimethoxy-4-oxy-4-nitrostilbene and 3,5-dimethoxy-4-oxy-2,4-nitrostilbene in the side chain. The resulting polymer 3 and 6 were soluble in DMSO and DMF. The inherent viscosities of polymers were in the range of 0.28–0.33 dL/g in DMSO. Polymers 3 and 6 showed good thermal stabilities in their TGA thermograms, and the T_g values from DSC thermograms were in the range of 81–87°C.     

Synthesis and characterization of poly(1-sila-cis-pent-3-enes) substituted with pendant pyridinyl groups

Poly[1-methyl-1-[3-(3-pyridinyl)propyl]-1-sila-cis-pent-3-ene], poly[1-phenyl-1-[3-(3-pyridinyl)propyl)-1-sila-cis-pent-3-ene], and poly[1-phenyl-1-(4-pyridinyl)-1-sila-cis-pent-3-ene] were synthesized by the anionic ring-opening polymerization of 1-methyl-1-[3-(3-pyridinyl)propyl]-1-silacyclopent-3-ene, 1-phenyl-1-[3-(3-pyridinyl)propyl]-1-silacyclopent-3-ene, and 1-phenyl-1-(4-pyridinyl)-1-silacyclopent-3-ene, respectively. These are the first polycarbosilanes which contain heterocyclic pyridine units as side-chain substituents. These polymers were characterized by¹H,¹³C, and²⁹Si NMR as well as by IR and UV spectroscopy. The molecular weight distributions were determined by gel permeation chromatography, glass transition temperatures, by differential seanning calorimetry: (DSC) and thermal behavior, by thermogravimetric analysis. (TGA).     

Dynamic mechanical properties of crosslinked polyisoprene under deformation

Summary Molecular motions of elastomers under deformations were observed through dynamic mechanical measurements. Composite master curves of dynamic moduli E and E and loss tangent tan over a wide range of frequency and in a state of elongation were obtained by the time-temperature superposition procedure. It is found that both moduli increase with strain, . The slope of the dispersion curve of E become more gradual with the increase in , while that of E is almost unchanged. The increment of E is generally larger than that of E, which does not agree with the N. W. Tschoegl prediction, E ^* ()=f() E _o ^* (), where E ^* () and E _o ^* () are complex moduli at the strain of and O, respectively, and f() is the function of only . The difference in the strain dependence of E from E was found to correspond to the strain dependence of the equilibrium modulus.     

Electrochemical behaviour of viologen-cyclodextrin inclusion complexes. The case of non-alkyl group substituted viologen

The electrochemical behavior of non-alkyl substituted viologen, 4,4-dibenzyl bipyridinium (BzV), 4,4-dicyanophenyl bipyridinium (CyV) and -,-,-cyclodextrin (, , -CD) was studied using cyclic voltammetry and a spectroelectrochemical method. It was found that BzV and Fe(CN) ₆ ^4– formed a charge-transfer (CT) complex with a ratio of 21 and the colour of the solution faded with the addition of an electrolyte. This behaviour is the same as in then-heptyl viologen and ferrocyanide system [1]. BzV, -CD and -CD formed an inclusion complex only in the reduced state, whilst BzV and -CD formed an inclusion complex in both the oxidized and the reduced state. An EC scheme in which a chemical reaction follows an electrochemical reaction was considered to predominate in the BzV and -, -CD systems, while a CE scheme in which a chemical reaction preceded an electrochemical reaction predominated in the BzV and -CD system. On the other hand, CyV was found to form an inclusion complex with -, -, -CD in both the oxidized and the reduced states. therefore a CE scheme was considered to predominate in the CyV--, -, -CD systems.     

Synthesis and thermal properties of block copolyetheresters with poly(pentamethylene p,p′-bibenzoate) segments

The block copolyetheresters with hard segments of poly(pentamethylene p,p-bibenzoate) and soft segments of poly (tetramethylene ether) were prepared by melt polycondensation of dimethyl-p,p-bibenzoate, 1,5-pentanediol and poly (tetramethyene ether) glycol (PTMEG) with molecular weights of 650, 1000 and 2000. The results by NMR indicate that the polymer composition is determined by the charge molar ratio (x) of PTMEG to dimethyl-p,p-bibenzoate. The thermal transitions of the block copolyetheresters were investigated by DSC in combination with X-ray diffraction and polarized microscopy. Some block copolyetheresters exhibit a monotropic smectic phase due to the presence of the poly (pentamethylene p,p-bibenzoate) segments. As the molar content of PTMEG increases, the average sequence length of the polyester segments decreases, the isotropic-smectic transition temperature and the smectic order decrease accordingly. When x is as high as 0.3, the block copolyetheresters exhibit no liquid crystallinity.     

Comparison of some 4- and 4,4′-substituted derivatives of stilbene for their reactivities towards the benzoyloxy radical

Summary 4-Fluoro- and 4,4-difluorostilbene are similar in their reactivities towards the benzoyloxy radical; a similar conclusion has been reached in respect of 4-chloro- with 4,4-dichlorostilbene and 4-phenyl-with 4,4-diphenylstilbene. These results have been obtained by consideration of the numbers of benzoate and phenyl end-groups in poly (methyl methacrylate) made using benzoyl peroxide in the presence of the appropriate derivative of stilbene.     

Preparation of Linear π-Conjugated Coordination Polymers Having Ruthenium(II) Complex in the Main Chain

Soluble -conjugated coordination polymers having a ruthenium(II) complex in the main chain were prepared from a soluble metal complex monomer and a bridging ligand via coordination. Refluxing of an ethanol-water suspension containing (4,4-dinonyl-2,2-bipyridyl)Ru(III) with 2,3-bis(2-pyridyl)pyrazine gave the coordination polymer. The resulting polymer was soluble in common organic solvents. The structure was confirmed by uv/vis spectra and gpc analysis.     

The electrochemical properties of polyaniline derivatives: poly(4,4′-diphenylamine methylenes) and poly(4,4′-diphenylimine methines)

Summary The electrochemical properties of poly(4,4-diphenylamine methylenes) and poly(4,4-diphenylimine methines) were investigated by cyclic voltammetry. A dehydrogenation reaction occured when poly(4,4-diphenylamine methylenes) underwent a electrochemical reaction and transformed to poly(4,4-diphenylimine methines). The fully oxidized poly(4,4-diphenylimine methines) had the electrochemical band gaps of 1.60–1.72 eV, which were found to significantly smaller than those of the fully reduced poly(4,4-diphenylamine methylenes).     

Chemical modification of copoly(methylsilylene/1,4-phenylene) by Pt-catalyzed hydrosilation reactions with functionally substituted alkenes

Copoly(methyl-3-biphenoxypropylsilylene 1,4-phenylene), copoly(methyl-3-cyanopropylsilylene 1,4-phenylene), copoly(methyl-3-ethoxypropylsilylene 1,4-phenylene), copoly(methyl-3-phenoxypropylsilylene 1,4-phenylene), and copoly(methyl-4,7,10,13-tetraoxatetradecanylsilylene 1,4-phenylene) have been prepared by platinum-catalyzed hydrosilation graft reactions between poly (methylsilylene 1,4-phenylene) and appropriate functionally substituted alkenes. These polymers have been characterized by¹H,¹³C, and²⁹Si NMR as well as by FT-IR and UV-vis spectroscopy. The molecular weight distribution of these polymers has been determined by gel permeation chromatography (GPC), and their glass transition temperatures (T _e) by DSC.     

Shape-selective synthesis of 4,4′-dimethylbiphenyl. 1. Methylation of 4-methylbiphenyl over modified zeolite catalysts

Methylation of 4-methylbiphenyl with methanol was carried out using zeolites HY, HM, and HZSM-5 as catalysts under fixed-bed down-flow conditions. HY and HM display no shape selectivity, but HZSM-5 shows moderate selectivity to the target product, 4,4-dimethylbiphenyl (4,4-DMBP) under proper reaction conditions. Modification of the surface of HZSM-5 zeolite can improve the selectivity to 4,4-DMBP, especially the simultaneous modification of external and internal surface with inorganic P compound. The selectivity to 4,4-DMBP can be increased to as high as 65% over the HZSM-5 modified with a small amount of ammonium hydrogen phosphate.     

Ruthenium catalyzed regioselective step-growth copolymerization of 4′-methoxyacetophenone,or 4′-phenoxyacetophenone and α, ω-dienes

Summary Ruthenium catalyzed step growth copolymerization of 4-methoxyacetophenone or 4-phenoxyacetophenone and ,-dienes such as 1,3-divinyltetramethyldisiloxane or 3,3,6,6-tetramethyl-3,6-disila-1,7-octadiene give copolymers which have respectable molecular weights. The synthesis and characterization of these copolymers is reported. Higher molecular weight copolymers are quite thermally stable.     

Hydride transfer to some initiators of cationic polymerization

Summary The hydride transfer from xanthene to stable carbenium salts with different cation electrophilities: 2,4,4'-trichlorotriphenylmethylhexachloroantimonate, triphenylmethylhexafluoroarsenate, triphenylmethylhexachloroantimonate, 4,4,4'-trimethyltriphenylmethylhexachloroantimonate and tropylium hexachloroantimonate is investigated. The reaction is controlled by the absorption of the carbenium ions in the visible region of their electronic spectra. The formation of the product of the reaction — triphenylmethane — is detected by gas chromatography and NMR spectroscopy. The rate constants and the reaction order are determined. The acceleration of the hydride transfer on UV-irradiation of the reaction mixture is shown.Paper presented at VII International Symposium Polymers '80, Varna, Bulgaria     

Liquid crystalline polyethers based on conformational isomerism

Summary The synthesis and characterization of copolyethers based on 1-(4-hydroxyphenyl)-2-(2-methyl-4-hydroxyphenyl)ethane (MBPE), 1,8-dibromooctane and each of the following three nonmesogenic bisphenols: 3,4-dihydroxydiphenylmethane (3,4-BPM), 4,4-isopropylidenediphenol (4,4-BPA) and 3,4-isopropylidenediphenol (3,4-BPA) are presented. Copolymers based on MBPE, 3,4-BPM and 1,8-dibromooctane display a nematic mesophase up to compositions containing as much as 70 mol% of 3,4-BPM. The range of mesomorphism decreases on going from 3,4-BPM to 3,4-BPA and to 4,4-BPA. These results demonstrate that structural units derived from parent amorphous and liquid crystalline homopolymers can be isomorphous within the mesophase over a certain range of copolymer composition of the resulting copolymers. Subsequently, the parameters of the mesomorphic phase transitions of these copolymers represent weight averaged values of the corresponding parameters of the parent homopolymers.Part 12: V. Percec and Y. Tsuda, Polymer submitted     

Photochromic polymers

Summary Two soluble photochromic polymers containing 1-(ß-hydroxyethyl)-3,3-dimethyl-6-nitrospiro[2H-1-benzopyran-2,2-indoline] bound on a variously long side chain were prepared. It was found that the discolouration process depends on the length of the side chain to which the photochromic centre is bound.