新型隧道带间级联双波长半导体激光器

提出了通过隧道带间级联实现半导体激光器有多个激射波长的新型物理思想 ,并以GaAs为隧道结 ,InGaAs应变量子阱为有源区 ,利用金属有机物化学气相沉积 (MOCVD)生长了含有两个有源区的双波长半导体激光器。制备了 90 μm条宽的脊型波导器件结构 ,测试得到了能同时激射 95 1nm和 986nm两个波长的双波长半导体激光器 ,腔面未镀膜时的斜率效率达到了 1 12W A ,垂直远场为基模 ,水平方向发散角为 10° ,垂直方向发散角为 36°。     

大功率670nm半导体激光器的研制

采用低压金属有机化学气相沉积生长了670nm激光器外延片，有源区采用单量子阱结构，阱区、垒区分别为InGaAsP和AlGaInP. 利用该外延片制作了带无电流注入区的氧化物条形激光器. 激光器腔长为900μm，电流注入区条宽为100μm，两端的无注入区宽度均为25μm. 镀膜后器件的阈值电流为0.4A，输出波长670±2nm，最大输出功率为1100mW, 水平、垂直发散角分别为8°, 40°. 表明该种结构可以提高器件的腔面光灾变功率.     

隧道再生结构的垂直腔面发射激光器激射特性研究

对隧道再生多有源区内腔接触式垂直腔面发射激光器(VCSEL)材料特性进行了实验研究,得到了VCSEL外延片量子阱增益谱峰值波长、谐振腔谐振波长、DBR反射谱中心波长及材料的生长厚度偏差等重要信息。如果谐振腔谐振波长比增益谱峰值波长长20nm以上,阈值条件很难得到满足,器件很难实现激射。符合模拟参数生长的双有源区隧道再生VCSEL实现了室温激射。氧化孔径8.3μm器件,在11mA注入电流下,获得5mW的输出功率,斜率效率0.702mW/mA,激射波长970nm。     

MOCVD生长双波长发光二极管

根据白光照明和可变换波长的光通信中对单芯片双波长发光二极管(LED)要求,在分析了反向偏置隧道结性质的基础上,设计了用反向偏置隧道结连接两个有源区的单芯片双波长LED,用金属有机化学气相沉积技术(MOCVD)在GaAs衬底上一次外延生长了同时发射两种波长的LED,其包含一个AlGaInP量子阱有源区和一个GaInP量子阱有源区,两个有源区由隧道结连接;通过后工艺制备了双波长LED器件,在20mA电流注入下,可以同时发射626nm和639nm两种波长,光强是127mcd,正向电压是4.17V。与传统的单有源区LED进行对比表明,双波长LED有较强的光强;对比单有源区LED的2.08V正向电压,考虑到双波长LED包含隧道结和两个有源区,隧道结上的压降很小。     

905nm隧道带间级联非耦合双有源区半导体激光器

通过对有源区、波导层、限制层和隧道结的分析 ,设计了激射波长为905nm的隧道带间级联非耦合双有源区半导体激 光器。采用金属有机物化学汽相淀积(MOCVD)系统外延法生长了器件,并经过光刻、 腐蚀、解理和焊装等工艺,制备了激射波长为905nm的隧道带间级联 非耦合双有源区半导体激光器。腔面 未镀膜时,在1.2A的脉冲注入电流下,器件的峰值波长为904.4nm,垂直远场为单峰,发 散角为25.8°,表明两个有源区的光场未发生耦合,斜率效率为1.12W/A,为相同结构单有源区器件的1.9倍。     

高饱和电流14xx nm应变量子阱激光器的研制

报道了14xx nm应变量子阱(SQW)激光器管芯的研制成果。通过金属有机化学气相沉积(MOCVD)生长工艺生长14xx nm AlGaInAs/AlInAs/InP应变量子阱外延片,采用带有锥形增益区的脊型波导结构制作激光器管芯。生长好的外延片按照双沟脊型波导激光器制备工艺进行光刻、腐蚀,制作P面电极(溅射 TiPtAu)、减薄、制作N面电极(蒸发AuGeNi),然后将试验片解理成Bar;为获得高的单面输出功率,用电子回旋共振等离子体化学气相沉积(ECR)进行腔面镀膜,HR=90%,AR=5%;解理成的管芯P面朝下烧结到铜热沉上,TO3封装后在激光器综合测试仪进行测试。管芯功率达到440 mW以上,饱和电流3 A以上,峰值波长1430 nm,远场发散角为40°×14°。     

1.3μm高增益偏振无关应变量子阱半导体光放大器

采用低压金属有机化学气相外延法 (LP MOVPE)生长并制作了 1 3μm脊型波导结构偏振无关半导体光放大器 (SOA) ,有源区为基于四个压应变量子阱和三个张应变量子阱交替生长的混合应变量子阱 (4C3T)结构 ,压应变阱宽为 6nm ,应变量 1 0 % ,张应变阱宽为 11nm ,应变量 - 0 95 % ;器件制作成 7°斜腔结构以有效抑制腔面反射。半导体光放大器腔面蒸镀Ti3 O5/Al2 O3 减反 (AR)膜以进一步降低腔面剩余反射率至 3× 10 -4以下 ;在 2 0 0mA驱动电流下 ,光放大器放大的自发辐射 (ASE)谱的 3dB带宽大于 5 0nm ,光谱波动小于 0 4dB ,半导体光放大器管芯的小信号增益近 30dB ,在 12 80～ 1340nm波长范围内偏振灵敏度小于 0 6dB ,饱和输出功率大于 10dBm ,噪声指数 (NF)为 7 5dB。     

键合方法研制InAsP/InGaAsP量子阱1.3μm垂直腔面发射激光器

设计并研制了由InAsP/InGaAsP应变补偿多量子阱有源层、SiO2/TiO2介质薄膜和GaAs/Al(Ga)As半导体分布布拉格反射镜(DBR)构成的垂直腔面发射激光器(VCSEL).采用直接键合技术实现InP基有源层与GaAs基DBR的晶片融合,并经过侧向湿法腐蚀定义电流限制孔径和沉积介质薄膜DBR等关键器件工艺,研制出InAsP/InGaAsP量子阱垂直腔面发射激光器,其阈值电流为13.5mA,单模激射波长为1288.6nm.     

940 nm高功率半导体激光器研究

报道了一种采用大光学腔结构的InGaAs/GaAs/AlGaAs应变量子阱高功率半导体激光器。在量子阱能级本征值方程的数值求解基础上 ,优化了InGaAs阱层材料的In组份含量 ;采用大光学腔结构以有效降低垂直于结平面方向的光束发散角及腔面的光功率密度 ,实现器件的高功率、低发散角光。设计的激光器外延结构采用分子束外延 (MBE)方法生长 ,成功获得具有较低激射阈值的 94 0nm波长激光器外延片。对 10 0 μm条形 ,10 0 0 μm腔长的制备器件测试表明 ,器件的最大连续输出功率达到 2W ,峰值波长为 939.4nm ,远场水平发散角为 10° ,垂直发散角为 30°。器件的阈值电流为 30 0mA。     

大功率670nm半导体激光器的研制

采用低压金属有机化学气相沉积生长了670nm激光器外延片,有源区采用单量子阱结构,阱区、垒区分别为InGaAsP和AlGaInP.利用该外延片制作了带无电流注入区的氧化物条形激光器.激光器腔长为900μm,电流注入区条宽为100μm,两端的无注入区宽度均为25μm.镀膜后器件的阈值电流为0.4A,输出波长670士2nm,最大输出功率为1100mW,水平、垂直发散角分别为8°,40°.表明该种结构可以提高器件的腔面光灾变功率.     

聚对苯撑苯并双(口恶)唑发光及其器件制备

采用光谱技术,研究了聚对苯撑苯并双(口恶)唑(PBO)溶液的光敏发光特性,并用相对法估算出溶液发光效率在50%范围.结合光谱技术、半导体电学和电化学等研究手段,具体研究了以PBO为发光层的单层电致发光器件,研究结果显示,电致发光与薄膜的光致发光有具有相同的发光中心,峰值位于510 nm左右.同时发现,由于存制备过程中不同处理条件使得不同厚度薄膜残留的掺杂物质浓度不同,从而引起薄膜的导电性的不同.使得器件的阈值场强随PBO厚度的减小而逐渐增加.     

系统级封装新型埋入式电源滤波结构的研究

在高密度小尺寸的系统级封装(SiP)中,对供电系统的完整性要求越来越高,多芯片共用一个电源网路所产生的电压抖动除了会影响到芯片的正常工作,还会通过供电网路干扰到临近电路和其他敏感电路,导致芯片误动作,以及信号完整性和其他电磁干扰问题.这种电压抖动所占频带相当宽,几百MHz到几个GHz的中频电源噪声普通方法很难去除.结合埋入式电容和电源分割方法的特点,提出一种新型高性能埋入式电源低通滤波结构直接替代电源/地平面.研究表明,在0.65～4GHz的频带内隔离深度可达-40～75 dB,电源阻抗均在0.25ohm以下,实现了宽频高隔离度的高性能滤波作用.分别用电磁场和广义传输线两种仿真器模拟,高频等效电路模型分析这种低通滤波器的工作原理以及结构对隔离性能的影响,并进行了实验验证.     

Emerging interconnects: a state-of-the-art review and emerging solutions

Aluminium was a primary material for interconnection in integrated circuits (ICs) since their inception. Later, copper was introduced as interconnect material which has better metallic conductivity and resistance to electromigration. As the aggressive technology scaling continues, the copper resistivity increased because of size effects, which causes increase in delay, power dissipation and electromigration. The need to reduce the resistor-capacitor??????? delay, dynamic power utilisation and the crosstalk commotion is as of now the fundamental main impetus behind the presentation of new materials. The purpose of this paper is to do a survey of interconnect material used in IC from introduction of ICs to till date. This paper studies and reviews new materials available for interconnect application which are optical interconnects, carbon nanotube (CNT), graphene nanoribbons (GNRs) and silicon nanowires which are alternatives to copper. While doing a survey of interconnect material, it is found that multiwalled CNTs, multilayer GNR and mixed CNT bundles are promising candidates and are ultimate choice that can strongly address the problems faced by copper but on integration basis copper would last for coming years.     

Arsenic deposition as a precursor layer on silicon (211) and (311) surfaces

We investigate the properties of arsenic (As) covered Si(211) and Si(311) surfaces by analyzing data from x-ray photoelectron spectroscopy (XPS) and low-energy electron diffraction (LEED) images. We then create a model using total surface energy calculations. It was found that both Si(211) and Si(311) had 0.68±0.08 surface As coverage. Si(211) had 0.28±0.04 Te coverage and Si(311) had 0.24±0.04 Te coverage. The Si(211) surface replaces the terrace and trench Si atoms with As for a lower surface energy, while the Si edge atoms form dimers. The Si(311) surface replaces all terrace atoms and adsorbs an As dimer every other edge site. These configurations imply an improvement in the mean migration path from the bare silicon surface by allowing the impinging atoms for the next epitaxial layer, tellurium (Te), to bind at every other pair of edge atoms, and not the step terrace sites. This would ensure a nonpolar, B-face growth.     

光子晶体微腔发光二极管

光子晶体微腔因其具有增强自发辐射、定向输出和单模工作的能力而受到广泛关注。介绍了光子晶体微腔发光二极管的基本原理、设计、特性、制作及其典型器件。     

Comparative study of maximum power point tracking techniques for hybrid renewable energy system

The power generation demand is increasing day-by-day throughout the world, therefore, the use of hybrid systems becomes a significant solution. The hybrid renewable energy system (HRES) is used for delivering power in various regions in order to overcome intermittence of wind and solar resources. Because of increasing environmental problems, for example, greenhouse gas emission and energy cost have interested novel research into substitute methods in favour of electrical power generation. Maximum Power Point Tracking (MPPT) control method is a vast deal of novel research used for enhancing the efficiency of HRES. The authors have revealed that the hybrid techniques i.e. Global MPPT, fuzzy-neuro systems, Adaptive Neuro-Fuzzy Inference System (ANFIS), Perturbed and Observe (P&O) + Adaptive Neural Network (ANN) etc. can provide best results as compared to other MPPT control methods. This paper offering a state of art review of MPPT control techniques for HRES.     

用于单光子TOF测量的时间-幅度变换器

基于新型共源共栅电流源的积分方法,设计了一种用于单光子飞行时间(TOF)测量的时间-幅度变换器(TAC).该方法有效简化了 TAC电路结构,减小了 TAC占用面积,显著提高了TOF的满量程范围(FSR).采用0.18 μm标准CMOS工艺设计.集成TAC的单光子探测器像素单元的填充因子可达到26.8％.后仿真结果表明,...     

超宽带脉冲信号的光学生成方法研究

近年来超宽带(UWB)通信技术迅猛发展,在测量、雷达技术、民用和军事无线通信中有着重要的应用,UWB-over-fiber技术已经成为目前研究的热点,其中就包括UWB脉冲信号的产生方法。区别于传统的电子学方法,光子学产生方法不受电子瓶颈制约,可以实现很高的带宽,并且具有抗电磁干扰、重量轻、结构紧凑的优点。通过对比国内外本领域研究成果,讨论及总结了以下三种原理的UWB脉冲信号的光学生成方法:1)相位调制-强度调制转换(PM-IM);2)半导体光放大器(SOA)的非线性效应;3)频谱塑形和色散所致频域-时域映射,然后对各种方案进行了对比分析。     

Joint estimation of TOA and DOA in IR-UWB system using a successive propagator method

Impulse radio ultra-wideband (IR-UWB) ranging and positioning require accurate estimation of time-of-arrival (TOA) and direction-of-arrival (DOA). With receiver of two antennas, both of the TOA and DOA parameters can be estimated via two-dimensional (2D) propagator method (PM), in which the 2D spectral peak searching, however, renders much higher computational complexity. This paper proposes a successive PM algorithm for joint TOA and DOA estimation in IR-UWB system to avoid 2D spectral peak searching. The proposed algorithm firstly gets the initial TOA estimates in the two antennas from the propagation matrix, then utilises successively one-dimensional (1D) local searches to achieve the estimation of TOAs in the two antennas, and finally obtains the DOA estimates via the difference in the TOAs between the two antennas. The proposed algorithm, which only requires 1D local searches, can avoid the high computational cost in 2D-PM algorithm. Furthermore, the proposed algorithm can obtain automatically paired parameters and has better joint TOA and DOA estimation performance than conventional PM algorithm, estimation of signal parameters via rotational invariance techniques algorithm and matrix pencil algorithm. Meanwhile, it has very close parameter estimation to that of 2D-PM algorithm. We have also derived the mean square error of TOA and DOA estimation of the proposed algorithm and the Cramer-Rao bound of TOA and DOA estimation in this paper. The simulation results verify the usefulness of the proposed algorithm.     

多孔硅发光机制的分析

从量子力学的基本理论出发讨论了量子限制效应，推导出多孔硅有效禁带宽度增量并用量子限制效应和表面态及其物质在发光中作用的理论解释了ＰＳ光致发光的实验现象。