镧和铈改性CuNi／Al2O3催化剂

采用浸渍法制备了稀土镧和铈改性的CuNi／Al2O3催化剂,研究了稀土负载量对催化剂活性和选择性的影响,并研究了催化剂的还原性能。结果表明：La和Ce的存在均降低了活性相CuO和NiO的还原温度,使改性催化剂具有更高的催化活性,但催化剂上乙烯的选择性则是Ce改性催化剂高于La改性催化剂,NCeO2含量为l％时,CeCuNi／Al2O3催化剂上乙炔转化率达到98％,乙烯选择性和收率则分别达到84％和82．3％,比未改性的CuNi／Al2O3催化剂上乙烯收率高16．4％,显示出CeO2改性CuNi／Al2O3催化剂的优异性能。     

Modelling of citral hydrogenation kinetics on an Ni/Al2O3 catalyst

The kinetics of citral hydrogenation in ethanol over an Ni/Al₂O₃ catalyst was studied in a slurry reactor operating at atmospheric pressure and at a temperature range of 60–77°C. Citronellal was the primary reaction product, whereas the amounts of unsaturated alcohols were very minor. Citronellol was the dominating product, generated mainly through the hydrogenation of the carbonyl group of citronellal. Based on the experimental data, a kinetic model was developed for hydrogenation. The model comprises competitive and rapid adsorption steps as well as rate-determining hydrogenation steps. The mass transfer limitation of hydrogen was included in the mathematical model. The kinetic parameters and the mass transfer parameter of hydrogen were estimated from the experimental data. A comparison of the model predictions with the experimental data revealed that the proposed kinetic approach gave a satisfactory reproduction of the data.     

预处理对Ru/Al_2O_3催化马来酸二甲酯加氢影响

采用吸附-沉淀法制备负载Ru质量分数为1.0%的Ru/Al_2O_3催化剂,以马来酸二甲酯催化加氢合成丁二酸二甲酯为探针反应,详细考察预处理条件对Ru/Al_2O_3催化剂加氢性能的影响,并对其进行XRD、TEM和H2-TPR表征。结果表明,焙烧温度越高,催化剂催化活性越低;直接还原活化所得催化剂活性高于空气中焙烧后还原活化所得催化剂。以甲醇为溶剂,在70℃和1.0 MPa条件下,直接还原活化所得Ru/Al_2O_3催化剂上马来酸二甲酯转化率达100%,丁二酸二甲酯选择性约100%。相同时间内,空气焙烧后还原活化所得Ru/Al_2O_3催化剂上马来酸二甲酯转化率接近25%,继续延长反应时间,马来酸二甲酯转化率几乎不变。经高温焙烧还原后,活性组分Ru烧结;直接还原活化后,活性组分Ru高度分散。     

Modeling of the enantioselective hydrogenation of 1-phenyl-1,2-propanedione over Pt/Al2O3 catalyst

A kinetic model was developed for the enantioselective hydrogenation of 1-phenyl-1,2-propanedione based on parallel racemic and enantioselective routes in the presence of cinchonidine. The Langmuir–Hinshelwood type of competitive adsorption approach was used in the model, which was combined with a batch reactor model. The proposed model could sufficiently describe the observed kinetic results.     

Hydrogenation of naphthalene on NiMo- Ni- and Ru/Al2O3 catalysts: Langmuir–Hinshelwood kinetic modelling

The importance of the hydrodearomatisation (HDA) is increasing together with tightening legislation of fuel quality and exhaust emissions. The present study focuses on hydrogenation (HYD) kinetics of the model aromatic compound naphthalene, found in typical diesel fraction, in n-hexadecane over a NiMo (nickel molybdenum), Ni (nickel) and Ru (ruthenium) supported on trilobe alumina (Al₂O₃) catalysts. Kinetic reaction expressions based on the mechanistic Langmuir–Hinshelwood (L–H) model were derived and tested by regressing the experimental data that translated the effect of both naphthalene and hydrogen concentration at a constant temperature (523.15 and 573.15 K over the NiMo catalyst and at 373.15 K over the Ni and Ru/Al₂O₃ catalysts) on the initial reaction rate. The L–H equation, giving an adequate fit to the experimental data with physically meaningful parameters, suggested a competitive adsorption between hydrogen and naphthalene over the presulphided NiMo catalyst and a non-competitive adsorption between these two reactants over the prereduced Ni and Ru/Al₂O₃ catalysts. In addition, the adsorption constant values indicated that the prereduced Ru catalyst was a much more active catalyst towards naphthalene HYD than the prereduced Ni/Al₂O₃ or the presulphided NiMo/Al₂O₃ catalyst.     

Characterization and catalytic activity of Pd/V2O5/Al2O3 catalysts on benzene total oxidation

The role of vanadium oxide and palladium on the benzene oxidation reaction over Pd/V₂O₅/Al₂O₃ catalysts was investigated. The Pd/V₂O₅/Al₂O₃ catalysts were more active than V₂O₅/Al₂O₃ and Pd/Al₂O₃ catalysts. The increase of vanadium oxide content decreased the Pd dispersion and increased the benzene conversion. A strong Pd particle size effect on benzene oxidation reaction was observed. Although the catalysts containing high amount of V⁴⁺ species were more active, the Pd particle size effect was responsible for the higher activity.     

焙烧温度对NiMo/Al2O3催化剂加氢性能的影响

采用不同的焙烧温度制备系列NiMo/Al₂O₃催化剂,运用BET、XRD、SEM和HRTEM等分析手段对催化剂进行表征,并以催化裂化进料为原料,在固定床高压反应器上对催化剂的加氢性能进行评价,着重考察焙烧温度对催化剂活性组分结构及活性的影响。结果表明,焙烧温度的升高有利于活性组分在催化剂表面的分散,但同时会增强活性组分与载体之间的相互作用,使催化剂活性相中单片层MoS₂片晶的数量增加,导致催化剂活性下降。
     

Ru-Fe/Al_2O_3氧化-还原性能探究

以Al_2O_3为载体,RuCl_3·xH_2O和FeCl_3·6H_2O为活性组分前驱体,采用吸附-沉淀法制备了Ru-Fe/Al_2O_3和Ru/Al_2O_3催化剂,以马来酸二甲酯加氢合成丁二酸二甲酯为探针反应,结合H_2-TPR和XRD表征技术,考察Fe改性Ru基催化剂的氧化-还原性能及催化活性。经氧化-还原循环处理后,催化剂Ru-Fe/Al_2O_3上马来酸二甲酯加氢活性高于Ru/Al_2O_3。XRD结果显示,经处理的Ru-Fe/Al_2O_3上未见金属Ru的特征衍射峰,而Ru/Al_2O_3上出现了金属Ru的特征衍射峰。结合H_2-TPR结果推断,Ru与Fe之间发生了相互作用,这种协同作用可以改善Ru/Al_2O_3催化剂的热稳定性。     

载体氧化铝的粒径对对硝基苯酚加氢催化剂Ni/Al2O3的影响

The catalytic hydrogenation of p-nitrophenol to p-aminophenol was investigated over Ni/Al2O3 catalyst on alumina support with different particle size. It is found that support particle size has significant influences on physiochemical properties and catalytic activity of the resulting Ni/Al2O3 catalyst, but little influence on the selec-tivity. At a comparable amount of Ni loading, the catalytic activity of Ni/Al2O3 prepared with alumina support of smaller particle size is lower. The reduction behavior of the catalyst is a key factor in determining the catalytic activity of Ni/Al2O3 catalyst. The supported nickel catalyst 10.3Ni/Al2O3-3 improves the life span of the membrane by reducing fouling on the membrane surface compared to nano-sized nickel.     

Al_2O_3焙烧温度对乙炔选择加氢催化剂性能的影响

采用浸渍法制备了NiCu/Al2O3乙炔选择加氢催化剂,研究了焙烧温度对Al2O3结构、酸性及催化剂催化性能的影响,结果表明：随着焙烧温度的提高,Al2O3的晶相结构由γ相逐渐转变为δ相和θ相,最后转化为α相,比表面积降低而孔径增大;酸强度逐渐降低最后直至消失。随Al2O3载体焙烧温度的提高,NiCu/Al2O3催化剂上乙炔的转化率和乙烯的选择性同时增加,当焙烧温度为1100℃时,乙炔的转化率和乙烯选择性分别为89.3%和77.5%。     

Ni/Al_2O_3催化剂的CO_2-TPD表征

Ni/Al_2O_3催化剂是甲烷二氧化碳重整反应制取合成气研究最多、最具应用潜力的一种催化剂。通过对催化剂进行CO_2-TPD研究,考察还原态Ni/Al_2O_3催化剂的CO_2脱附特性。结果表明,浸渍法制备的Ni/Al_2O_3催化剂CO_2脱附曲线呈现双峰,分别在(60~65)℃和(350~380)℃出现高低温两个活性位;高温CO_2吸附量为3.0 cm~3·g~(-1),低温CO_2吸附量为24.0 cm~3·g~(-1)。催化剂的CO_2吸附量与其Ni含量无关。考察选用不同载体的CO_2脱附行为,发现以Al_2O_3为载体的催化剂CO_2吸附量是MgO和SiO_2为载体催化剂的2~4倍,以TiO_2为载体的催化剂几乎不吸附CO_2。     

Physicochemical surface and catalytic properties of CuO–ZnO/Al2O3 system

A series of CuO–ZnO/Al₂O₃ solids were prepared by wet impregnation using Al(OH)₃ solid and zinc and copper nitrate solutions. The amounts of copper and zinc oxides were varied between 10.3 and 16.0 wt% CuO and between 0.83 and 7.71 wt% ZnO. The prepared solids were subjected to thermal treatment at 400–1000°C. The solid–solid interactions between the different constituents of the prepared solids were studied using XRD analysis of different calcined solids. The surface characteristics of various calcined adsorbents were investigated using nitrogen adsorption at −196°C and their catalytic activities were determined using CO-oxidation by O₂ at temperatures ranged between 125°C and 200°C.

The results showed that CuO interacts with Al₂O₃ to produce copper aluminate at ≥600°C and the completion of this reaction requires heating at 1000°C. ZnO hinders the formation of CuAl₂O₄ at 600°C while stimulates its production at 800°C. The treatment of CuO/Al₂O₃ solids with different amounts of ZnO increases their specific surface area and total pore volume and hinders their sintering (the activation energy of sintering increases from 30 to 58 kJ mol⁻¹ in presence of 7.71 wt% ZnO). This treatment resulted in a progressive decrease in the catalytic activities of the investigated solids but increased their catalytic durability. Zinc and copper oxides present did not modify the mechanism of the catalyzed reaction but changed the concentration of catalytically active constituents (surface CuO crystallites) without changing their energetic nature.     

Effect of Al2O3 on mechanical properties of Ti3SiC2/Al2O3 composite

The effect of Al₂O₃ on mechanical properties of Ti₃SiC₂/Al₂O₃ composite fabricated by SPS was studied systematically. The results show that the hardness of the Ti₃SiC₂/Al₂O₃ composite can reach 10.28 GPa, 50% higher than that of pure Ti₃SiC₂. However, slight decrease in the other mechanical properties was observed with Al₂O₃ addition higher than 5–10 vol.%, which is believed to be due to the agglomeration of Al₂O₃ in the composite.     

助剂对碳四馏分选择性加氢Pd/Al2O3催化剂性能的影响

以Al₂O₃为载体,Pd为活性组分,Ag和Li为助剂,制备碳四馏分选择性加氢脱除丁二烯催化剂,并对催化剂进行XPS、TPR和TPD表征。结果表明,加入助剂Ag使Pd的电子云密度升高,而加入助剂Li使催化剂表面酸中心数量减少。催化剂评价结果表明,加入助剂Ag和Li后,催化剂的1-丁烯双键异构活性降低,加氢选择性提高。     

The mechanism of SO2 effect on NO reduction with propene over In2O3/Al2O3 catalyst

An In₂O₃/Al₂O₃ catalyst shows high activity for the selective catalytic reduction of NO with propene in the presence of oxygen. The presence of SO₂ in feed gas suppressed the catalytic activity dramatically at high temperatures; however it was enhanced in the low temperature range of 473–573 K. In TPD and FT-IR studies, the formation of sulfate species on the surface of the catalyst caused an inhibition of NO_X adsorption sites, and the absorbance ability of NO was suppressed by the presence of SO₂, and the amount of ad-NO₃⁻ species decreased obviously. This leads to a decrease of catalytic activity at higher temperatures. However, addition of SO₂ enhanced the formation of carboxylate and formate species, which can explain the promotional effect of SO₂ at low temperature, because active C₃H₆ (partially oxidized C₃H₆) is crucial at low temperature.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Carbon dioxide reforming of methane over Ni/Al2O3 treated with glow discharge plasma

Ni/Al₂O₃ catalyst was first treated by argon glow discharge plasma followed by calcination in air. The catalyst prepared this way exhibits an improved low-temperature activity for carbon dioxide reforming of methane, compared to the catalyst prepared without plasma treatment. The catalyst characterization using XRD, chemisorption and TEM analyses show that the plasma treatment followed by calcination thermally induces a generation of specific nickel species on the support. This kind of “plasma” metal species is highly dispersed on the support and can remain stable during reforming reactions. The average size of the “plasma” metal particles is ca. 5 nm. The plasma treatment can also enhance the anti-carbon deposition performance of the catalyst. The formation of carbon species that is responsible for catalyst deactivation can be inhibited. The catalyst stability is therefore improved.     

The effect of hydrogen on the selective catalytic reduction of NO in excess oxygen over Ag/Al2O3

The selective catalytic reduction (SCR) of nitrogen oxides (NO_x) by propane in the presence of H₂ on sol–gel prepared Ag/Al₂O₃ catalysts (0.5–5 wt.% Ag) was investigated. It was confirmed that hydrocarbon-assisted SCR of NO_x is remarkably enhanced by co-feeding hydrogen to a lean exhaust gas mixture (λ>1), attaining considerable activity within a wide temperature window (470–825 K). The samples had marginal activity at 575 K without co-fed H₂, but achieved up to 60% NO_x conversion in the presence of H₂ at a space velocity of 30,000 h⁻¹. NO₂ as NO_x feed component is not converted to N₂ by C₃H₈ to a substantial extent under lean conditions. This points to an activation route of NO through direct conversion to adsorbed nitrite/nitrate or to a dissociation of NO over Ag⁰, formed through short-term reduction by H₂. The nature of Ag species was characterized by X-ray diffraction, temperature-programmed reduction, pulse thermoanalytical measurements, electron microscopy and FTIR spectroscopy. It could be shown that Ag₂O nano-sized clusters are predominantly present on all samples, whereas formation of silver aluminate could not be confirmed. Nano-sized Ag₂O clusters can reversibly be reduced/reoxidized by H₂. A silver loading higher than 2 wt.% leads to a part of Ag₂O particles, which are thermally decomposed during calcination at 800 K or higher. The catalytic role of this metallic silver is still unclear. Formal kinetic analysis of catalytic data revealed that the activation energy of the overall reaction is significantly lowered in the presence of H₂. The presence of water does not change the activation energy. It is concluded that hydrogen reduces the nano-sized Ag₂O clusters to Ag⁰ on a short-term scale. Zero-valent silver promotes a dissociation pathway of NO_x conversion. The fact that more oxidized ad-species (nitrite/nitrate) are observed in the presence of H₂ is attributed to a dissociative activation of gas-phase oxygen on Ag⁰.     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.