Optimizing annealing steps for crystalline silicon solar cells with screen printed front side metallization and an oxide‐passivated rear surface with local contacts

Silicon solar cells that feature screen printed front contacts and a passivated rear surface with local contacts allow higher efficiencies compared to present industrial solar cells that exhibit a full area rear side metallization. If thermal oxidation is used for the rear surface passivation, the final annealing step in the processing sequence is crucial. On the one hand, this post‐metallization annealing (PMA) step is required for decreasing the surface recombination velocity (SRV) at the aluminum‐coated oxide‐passivated rear surface. On the other hand, PMA can negatively affect the screen printed front side metallization leading to a lower fill factor. This work separately analyzes the impact of PMA on both, the screen printed front metallization and the oxide‐passivated rear surface. Measuring dark and illuminated IV‐curves of standard industrial aluminum back surface field (Al‐BSF) silicon solar cells reveals the impact of PMA on the front metallization, while measuring the effective minority carrier lifetime of symmetric lifetime samples provides information about the rear side SRV. One‐dimensional simulations are used for predicting the cell performance according to the contributions from both, the front metallization and the rear oxide‐passivation for different PMA temperatures and durations. The simulation also includes recombination at the local rear contacts. An optimized PMA process is presented according to the simulations and is experimentally verified. The optimized process is applied to silicon solar cells with a screen printed front side metallization and an oxide‐passivated rear surface. Efficiencies up to 18.1% are achieved on 148.8 cm² Czochralski (Cz) silicon wafers. Copyright © 2009 John Wiley & Sons, Ltd.     

19% efficient n‐type Czochralski silicon solar cells with screen‐printed aluminium‐alloyed rear emitter

High and stable lifetimes recently reported for n‐type silicon materials are an important and promising prerequisite for innovative solar cells. To exploit the advantages of the excellent electrical properties of n‐type Si wafers for manufacturing simple and industrially feasible high‐efficiency solar cells, we focus on back junction n⁺np⁺ solar cells featuring an easy‐to‐fabricate full‐area screen‐printed aluminium‐alloyed rear p⁺ emitter. Independently confirmed record‐high efficiencies have been achieved on n‐type phosphorus‐doped Czochralski‐grown silicon material: 18·9% for laboratory‐type n⁺np⁺ solar cells (4 cm²) with shadow‐mask evaporated front contact grid and 17·0% for front and rear screen‐printed industrial‐type cells (100 cm²). The electrical cell parameters were found to be perfectly stable under illumination. Copyright © 2006 John Wiley & Sons, Ltd.     

High‐efficiency (19%) screen‐printed textured cells on low‐resistivity float‐zone silicon with high sheet‐resistance emitters

High‐efficiency 4 cm² screen‐printed (SP) textured cells were fabricated on 100 Ω/sq emitters using a rapid single‐step belt furnace firing process. The high contact quality resulted in a low series resistance of 0·79 Ωcm², high shunt resistance of 48 836 Ωcm², a low junction leakage current of 18·5 nA/cm² (n₂ = 2) yielding a high fill factor (FF) of 0·784 on 100 Ω/sq emitter. A low resistivity (0·6 Ωcm) FZ Si was used for the base to enhance the contribution of the high sheet‐resistance emitter without appreciably sacrificing the bulk lifetime. This resulted in a 19% efficient (confirmed at NREL) SP 4 cm² cell on textured FZ silicon with SP contacts and single‐layer antireflection coating. This is apparently higher in performance than any other previously reported cell using standard screen‐printing approaches (i.e., single‐step firing and grid metallization). Detailed cell characterization and device modeling were performed to extract all the important device parameters of this 19% SP Si cell and provide guidelines for achieving 20% SP Si cells. Copyright © 2005 John Wiley & Sons, Ltd.     

All‐screen‐printed back‐contact back‐junction silicon solar cells with aluminum‐alloyed emitter and demonstration of interconnection of point‐shaped metalized contacts

In the following, high‐efficiency back‐contact back‐junction silicon solar cells with aluminum‐alloyed emitter are described. First, the theoretical background for the cell concept is explained. To that purpose, the bulk lifetime and the front surface field characteristics are considered. Three different process sequences for the phosphorus‐diffused profiles on the front and back surfaces are depicted: One exhibits a shallow field, and two sequences have deeper, driven‐in profiles. For realizing high efficiencies, such cell structures must meet several prerequisites, such as firing‐stable front and rear passivations, and functional small screen‐printed Al structures. Furthermore, it must be possible to create contacts on the Si surfaces using the driven‐in P‐profiles. With such a structure, cell efficiencies of 20.0% are reached. An analysis of the series resistance and area‐weighted recombination is performed. The results are compared with the measured cell parameters. Two‐dimensional simulations show the efficiency potential when decreasing the width of the backside field and when a cell structure, which would inhibit a passivated aluminum‐alloyed p⁺‐emitter, is created. Also, an advanced concept is demonstrated where a point array of both polarities on the cell backside is interconnected externally on module level. To that purpose, the cell is soldered to a printed wiring circuit board by using a reflow soldering process. Copyright © 2013 John Wiley & Sons, Ltd.     

Add‐on laser tailored selective emitter solar cells

An elegant laser tailoring add‐on process for silicon solar cells, leading to selectively doped emitters increases their efficiency η by Δη = 0.5% absolute. Our patented, scanned laser doping add‐on process locally increases the doping under the front side metallization, thus allowing for shallow doping and less Auger recombination between the contacts. The selective laser add‐on process modifies the emitter profile from a shallow error‐function type to Gaussian type and enables excellent contact formation by screen printing, normally difficult to achieve for shallow diffused emitters. The significantly deeper doping profile of the laser irradiated samples widens the process window for the firing of screen printed contacts and avoids metal spiking through the pn‐junction. Copyright © 2010 John Wiley & Sons, Ltd.     

Enhanced lateral current transport via the front N+ diffused layer of n‐type high‐efficiency back‐junction back‐contact silicon solar cells

N‐type back‐contact back‐junction solar cells were processed with the use of industrially relevant structuring technologies such as screen‐printing and laser processing. Application of the low‐cost structuring technologies in the processing of the high‐efficiency back‐contact back‐junction silicon solar cells results in a drastic increase of the pitch on the rear cell side. The pitch in the range of millimetres leads to a significant increase of the lateral base resistance. The application of a phosphorus doped front surface field (FSF) significantly reduces the lateral base resistance losses. This additional function of the phosphorus doped FSF in reducing the lateral resistance losses was investigated experimentally and by two‐dimensional device simulations. Enhanced lateral majority carrier's current transport in the front n⁺ diffused layer is a function of the pitch and the base resistivity. Experimental data show that the application of a FSF reduces the total series resistance of the measured cells with 3.5 mm pitch by 0.1 Ω cm² for the 1 Ω cm base resistivity and 1.3 Ω cm² for the 8 Ω cm base resistivity. Two‐dimensional simulations of the electron current transport show that the electron current density in the front n⁺ diffused layer is around two orders of magnitude higher than in the base of the solar cell. The best efficiency of 21.3% was obtained for the solar cell with a 1 Ω cm specific base resistivity and a front surface field with sheet resistance of 148 Ω/sq. Copyright © 2008 John Wiley & Sons, Ltd.     

Modeling the potential of screen printed front junction CZ silicon solar cell with tunnel oxide passivated back contact

Carrier selective passivated contacts composed of thin oxide, n + polycrystalline Si and metal on top of a n‐Si absorber can significantly lower the recombination current density (J_orear ≤8 fA/cm²) under the contact while providing excellent specific contact resistance (5–10 mΩ‐cm²); 25.1% efficient small area cells with photolithography front contacts on boron doped selective emitter and Fz wafers have been achieved by Fraunhofer ISE using their tunnel oxide passivated contact (TOPCon) approach. This paper shows a methodology to model such passivated contact cells using Sentaurus device model, which involves replacing the TOPCon region by carrier selective electron and hole recombination velocities to match the measured J_orear of the TOPCon region as well as all the light IV values of the cell. We first validated the methodology by modeling a 24.9% reference cell. The model was then extended to assess the efficiency potential of large area TOPCon cells on commercial grade n‐type Cz material with screen‐printed front contacts. To use realistic input parameters, a 21% n‐type PERT cell was fabricated on Cz wafer (5 Ω‐cm, 1.5‐ms lifetime). Modeling showed that the cell efficiency will improve to only 21.6% if the back of this cell is replaced by the above TOPCon, and the performance is limited by the homogenous emitter. Efficiency was then modeled to improve to 22.6% with the implementation of selective emitter (150/20 Ω/sq). Finally, it is shown that screen printing of 40‐µm‐wide lines and improved bulk material (10 Ω‐cm, 3‐ms lifetime) can raise the single side TOPCon Cz cell efficiency to 23.2%. Copyright © 2016 John Wiley & Sons, Ltd.     

Silicon solar cells based on all‐laser‐transferred contacts

Crystalline silicon solar cells based on all‐laser‐transferred contacts (ALTC) have been fabricated with both front and rear metallization achieved through laser induced forward transferring. Both the front and rear contacts were laser‐transferred from a glass slide coated with a metal layer to the silicon substrate already processed with emitter formation, surface passivation, and antireflection coating. Ohmic contacts were achieved after this laser transferring. The ALTC solar cells were fabricated on chemically textured p‐type Cz silicon wafers. An initial conversion efficiency of over 15% was achieved on a simple cell structure with full‐area emitter. Further improvements are expected with optimized laser transferring conditions, front grid pattern design, and surface passivation. The ALTC process demonstrates the advantage of laser processing in simplifying the solar cell fabrication by a one‐step metal transferring and firing process. Copyright © 2013 John Wiley & Sons, Ltd.     

Influence of temperature during phosphorus emitter diffusion from a spray‐on source in multicrystalline silicon solar cell processing

We have investigated the influence of diffusion temperature during phosphorus emitter diffusion from a spray‐on source on the performance of screen‐printed multicrystalline silicon solar cells. Because of the dual diffusion mechanism present at high concentration in‐diffusion of phosphorus in silicon, applying lower diffusion temperatures for a longer duration results in significantly enhanced penetration of the low concentration tail relative to the high concentration region. Moreover, we show that the sheet resistance of in‐diffused emitters from a high concentration source depends primarily on the extension of the high concentration region, thus significantly different emitter profiles can be manufactured without altering the sheet resistance considerably. Because of the enhanced tail penetration, emitters of a specified sheet resistance diffused at reduced temperatures can result in higher fill factors of screen‐printed solar cells due to diminution of Schottky type shunts. Furthermore, emitters diffused at lower temperatures for longer durations can yield a higher gettering efficiency, resulting in increased bulk recombination lifetime, and thus a higher internal quantum efficiency at long wavelengths. The deeper tail extension of low temperature emitters, however, causes increased absorption within the highly recombinative emitter, resulting in current losses due to a lower internal quantum efficiency at short wavelengths. Copyright © 2006 John Wiley & Sons, Ltd.     

DC‐sputtered ZnO:Al as transparent conductive oxide for silicon heterojunction solar cells with µc‐Si:H emitter

Silicon heterojunction (SHJ) solar cells are highly interesting, because of their high efficiency and low cost fabrication. So far, the most applied transparent conductive oxide (TCO) is indium tin oxide (ITO). The replacement of ITO with cheaper, more abundant and environmental friendly material with texturing capability is a promising way to reduce the production cost of the future SHJ solar cells. Here, we report on the fabrication of the SHJ solar cells with direct current‐sputtered aluminum‐doped zinc oxide (ZnO:Al) as an alternative TCO. Furthermore, we address several important differences between ITO and the ZnO:Al layers including a high Schottky barrier at the emitter/ZnO:Al interface and a high intrinsic resistivity of the ZnO:Al layers. To overcome the high Schottky barrier, we suggest employing micro‐crystalline silicon (µc‐Si:H) emitter, which also improves temperature threshold and passivation of the solar cell precursor. In addition, we report on the extensive studies of the effect of the ZnO:Al deposition parameters including layer thickness, oxygen flow, power density and temperature on the electrical properties of the fabricated SHJ solar cells. Finally, the results of our study indicate that the ZnO:Al deposition parameters significantly affect the electrical properties of the obtained solar cell. By understanding and fine‐tuning all these parameters, a high conversion efficiency of 19.2% on flat wafer (small area (5 × 5 mm²) and without any front metal grid) is achieved. Copyright © 2014 John Wiley & Sons, Ltd.     

High efficiency large area n‐type front junction silicon solar cells with boron emitter formed by screen printing technology

In this paper, we report on commercially viable screen printing (SP) technology to form boron emitters. A screen‐printed boron emitter and ion‐implanted phosphorus back surface field were formed simultaneously by a co‐annealing process. Front and back surfaces were passivated by chemically grown oxide capped with plasma‐enhanced chemical vapor deposition silicon nitride stack. Front and back contacts were formed by traditional SP and firing processes with silver/aluminum grid on front and local silver back contacts on the rear. This resulted in 19.6% efficient large area (239 cm²) n‐type solar cells with an open‐circuit voltage V_oc of 645 mV, short‐circuit current density J_sc of 38.6 mA/cm², and fill factor of 78.6%. This demonstrates the potential of this novel technology for production of low‐cost high‐efficiency n‐type silicon solar cells. Copyright © 2014 John Wiley & Sons, Ltd.     

Low‐temperature formation of local Al contacts to a‐Si:H‐passivated Si wafers

We have passivated boron‐doped, low‐resistivity crystalline silicon wafers on both sides by a layer of intrinsic, amorphous silicon (a‐Si:H). Local aluminum contacts were subsequently evaporated through a shadow mask. Annealing at 210°C in air dissolved the a‐Si:H underneath the Al layer and reduces the contact resistivity from above 1 Ω cm² to 14·9 m Ω cm². The average surface recombination velocity is 124 cm/s for the annealed samples with 6% metallization fraction. In contrast to the metallized regions, no structural change is observed in the non‐metallized regions of the annealed a‐Si:H film, which has a recombination velocity of 48 cm/s before and after annealing. Copyright © 2004 John Wiley & Sons, Ltd.     

Experimental and simulated analysis of front versus all‐back‐contact silicon heterojunction solar cells: effect of interface and doped a‐Si:H layer defects

Front silicon heterojunction and interdigitated all‐back‐contact silicon heterojunction (IBC‐SHJ) solar cells have the potential for high efficiency and low cost because of their good surface passivation, heterojunction contacts, and low temperature fabrication processes. The performance of both heterojunction device structures depends on the interface between the crystalline silicon (c‐Si) and intrinsic amorphous silicon [(i)a‐Si:H] layer, and the defects in doped a‐Si:H emitter or base contact layers. In this paper, effective minority carrier lifetimes of c‐Si using symmetric passivation structures were measured and analyzed using an extended Shockley–Read–Hall formalism to determine the input interface parameters needed for a successful 2D simulation of fabricated baseline solar cells. Subsequently, the performance of front silicon heterojunction and IBC‐SHJ devices was simulated to determine the influence of defects at the (i)a‐Si:H/c‐Si interface and in the doped a‐Si:H layers. For the baseline device parameters, the difference between the two device configurations is caused by the emitter/base contact gap recombination and the back surface geometry of IBC‐SHJ solar cell. This work provides a guide to the optimization of both types of SHJ device performance, predicting an IBC‐SHJ solar cell efficiency of 25% for realistic material parameters. Copyright © 2013 John Wiley & Sons, Ltd.     

Fine line printed silicon solar cells exceeding 20% efficiency

Silicon solar cells with passivated rear side and laser‐fired contacts were produced on float zone material. The front side contacts are built up in two steps, seed and plate. The seed layer is printed using an aerosol jet printer and a silver ink. After firing this seed layer through the silicon nitride layer, the conductive layer is grown by light induced plating. The contact formation is studied on different emitter sheet resistances, 55 Ω/sq, 70 Ω/sq, and on 110 Ω/sq. These emitters are passivated with a PECVD silicon nitride layer which also acts as an anti‐reflection coating. Even on the 110 Ω/sq emitters it was possible to reach a fill factor of 80·1%. The electrical properties i.e., the contact resistance of the front side contacts are studied by transfer length model (TLM) measurements. On a cell area of 4 cm² and emitter sheet resistance of 110 Ω/sq, a record efficiency of 20·3% was achieved. Excellent open‐circuit voltage (V_oc) and short‐circuit current (j_sc) values of 661 mV and 38·4 mA/cm² were obtained due to the low recombination in the 110 Ω/sq emitter and at the passivated rear surface. These results show impressively that it is possible to contact emitter profiles with a very high efficiency potential using optimized printing technologies. Copyright © 2008 John Wiley & Sons, Ltd.     

Combining laser chemical processing and aerosol jet printing: a laboratory scale feasibility study

First results showing the viability of combining laser chemical processing (LCP) and aerosol jet printing (AJP) technologies to produce a high‐efficiency front side for silicon solar cells are presented. LCP simultaneously opens the anti‐reflection coating (ARC) and highly dopes the underlying silicon to create a selective emitter, while AJP is the first in a two‐step fine‐line contact formation procedure. The electrical properties as well as the morphology of the resulting structures are presented. Performance similar to that achieved with evaporated TiPdAg metallization is demonstrated. Copyright © 2010 John Wiley & Sons, Ltd.     

Back‐contacted back‐junction n‐type silicon solar cells featuring an insulating thin film for decoupling charge carrier collection and metallization geometry

In this study, back‐contacted back‐junction n‐type silicon solar cells featuring a large emitter coverage (point‐like base contacts), a small emitter coverage (point‐like base and emitter contacts), and interdigitated metal fingers have been fabricated and analyzed. For both solar cell designs, a significant reduction of electrical shading losses caused by an increased recombination in the non‐collecting base area on the rear side was obtained. Because the solar cell designs are characterized by an overlap of the B‐doped emitter and the P‐doped base with metal fingers of the other polarity, insulating thin films with excellent electrical insulation properties are required to prevent shunting in these overlapping regions. Thus, with insulating thin films, the geometry of the minority charge carrier collecting emitter diffusion and the geometry of the interdigitated metal fingers can be decoupled. In this regard, plasma‐enhanced chemical vapor deposited SiO₂ insulating thin films with various thicknesses and deposited at different temperatures have been investigated in more detail by metal‐insulator‐semiconductor structures. Furthermore, the influence of different metal layers on the insulation properties of the films has been analyzed. It has been found that by applying a SiO₂ insulating thin film with a thickness of more than 1000 nm and deposited at 350 °C to solar cells fabricated on 1 Ω cm and 10 Ω cm n‐type float‐zone grown silicon substrates, electrical shading losses could be reduced considerably, resulting in excellent short‐circuit current densities of more than 41 mA/cm² and conversion efficiencies of up to 23.0%. Copyright © 2012 John Wiley & Sons, Ltd.     

Industrially feasible,dopant‐free,carrier‐selective contacts for high‐efficiency silicon solar cells

Dopant‐free, carrier‐selective contacts (CSCs) on high efficiency silicon solar cells combine ease of deposition with potential optical benefits. Electron‐selective titanium dioxide (TiO₂) contacts, one of the most promising dopant‐free CSC technologies, have been successfully implemented into silicon solar cells with an efficiency over 21%. Here, we report further progress of TiO₂ contacts for silicon solar cells and present an assessment of their industrial feasibility. With improved TiO₂ contact quality and cell processing, a remarkable efficiency of 22.1% has been achieved using an n‐type silicon solar cell featuring a full‐area TiO₂ contact. Next, we demonstrate the compatibility of TiO₂ contacts with an industrial contact‐firing process, its low performance sensitivity to the wafer resistivity, its applicability to ultrathin substrates as well as its long‐term stability. Our findings underscore the great appeal of TiO₂ contacts for industrial implementation with their combination of high efficiency with robust fabrication at low cost. Copyright © 2017 John Wiley & Sons, Ltd.     

High‐quality surface passivation of silicon solar cells in an industrial‐type inline plasma silicon nitride deposition system

We have studied the surface passivation of silicon by deposition of silicon nitride (SiN) in an industrial‐type inline plasma‐enhanced chemical vapor deposition (PECVD) reactor designed for the continuous coating of silicon solar cells with high throughput. An optimization study for the passivation of low‐resistivity p‐type silicon has been performed exploring the dependence of the film quality on key deposition parameters of the system. With the optimized films, excellent passivation properties have been obtained, both on undiffused p‐type silicon and on phosphorus‐diffused n⁺ emitters. Using a simple design, solar cells with conversion efficiencies above 20% have been fabricated to prove the efficacy of the inline PECVD SiN. The passivation properties of the films are on a par with those of high‐quality films prepared in small‐area laboratory PECVD reactors. Copyright © 2004 John Wiley & Sons, Ltd.     

A 3‐in‐1 doping process for interdigitated back contact solar cells exploiting the understanding of co‐diffused dopant profiles by use of PECVD borosilicate glass in a phosphorus diffusion

Boron and phosphorus doping of crystalline silicon using a borosilicate glass (BSG) layer from plasma‐enhanced chemical vapor deposition (PECVD) and phosphorus oxychloride diffusion, respectively, is investigated. More specifically, the simultaneous and interacting diffusion of both elements through the BSG layer into the silicon substrate is characterized in depth. We show that an overlying BSG layer does not prevent the formation of a phosphorus emitter in silicon substrates during phosphorus diffusion. In fact, a BSG layer can even enhance the uptake of phosphorus into a silicon substrate compared with a bare substrate. From the understanding of the joint diffusion of boron and phosphorus through a BSG layer into a silicon substrate, a model is developed to illustrate the correlation of the concentration‐dependent diffusivities and the emerging diffusion profiles of boron and phosphorus. Here, the in‐diffusion of the dopants during diverse doping processes is reproduced by the use of known concentration dependences of the diffusivities in an integrated model. The simulated processes include a BSG drive‐in step in an inert and in a phosphorus‐containing atmosphere. Based on these findings, a PECVD BSG/capping layer structure is developed, which forms three different n⁺⁺−, n⁺− and p⁺−doped regions during one single high temperature process. Such engineered structure can be used to produce back contact solar cells. Copyright © 2016 John Wiley & Sons, Ltd.     

Opto‐electrical modelling and optimization study of a novel IBC c‐Si solar cell

Interdigitated back contact (IBC) crystalline silicon (c‐Si) solar cells are attracting a lot of attention because of their capability to reach world record conversion efficiency. Because of the relatively complex contact pattern, their design and optimization typically require advanced numerical simulation tools. In this work, a TCAD‐based simulation platform has been developed to account accurately and in detail the optical and passivation mechanisms of front texturization. Its validation has been carried out with respect to a novel homo‐junction IBC c‐Si solar cell based on ion implantation and epitaxial growth, comparing measured and simulated reflectance, transmittance, internal quantum efficiency, external quantum efficiency spectra, and current density–voltage characteristics. As a result of the calibration process, the opto‐electrical losses of the investigated device have been identified quantitatively and qualitatively. Then, an optimization study about the optimal front surface field (FSF) doping, front‐side texturing morphology, and rear side geometry has been performed. The proposed simulation platform can be potentially deployed to model other solar cell architectures than homo‐junction IBC devices (e.g., passivated emitter rear cell, passivated emitter rear locally diffused cell, hetero‐IBC cell). Simulation results show that a not‐smoothed pyramid‐textured front interface and an optimal FSF doping are mandatory to minimize both the optical and the recombination losses in the considered IBC cell and, consequently, to maximize the conversion efficiency. Similarly, it has been showed that recombination losses are affected more by the doping profile rather than the surface smoothing. Moreover, the performed investigation reveals that the optimal FSF doping is almost independent from the front texturing morphology and FSF passivation quality. According to this result, it has been demonstrated that an IBC cell featuring an optimal FSF doping does not exhibit a significant efficiency improvement when the FSF passivation quality strongly improves, proving that IBC cell designs based on low‐doped FSF require a very outstanding passivation quality to be competitive. Deploying an optimization algorithm, the adoption of an optimized rear side geometry can potentially lead to an efficiency improvement of about 1%_abs as compared with the reference IBC solar cell. Further, by improving both emitter and c‐Si bulk quality, a 22.84% efficient solar cell for 280‐μm thick c‐Si bulk was simulated. Copyright © 2017 John Wiley & Sons, Ltd.