Mechanical properties of natural fiber hybrid composites based on renewable thermoset resins derived from soybean oil,for use in technical applications

Natural fiber composites are known to have lower mechanical properties than glass or carbon fiber reinforced composites. The hybrid natural fiber composites prepared in this study have relatively good mechanical properties. Different combinations of woven and non‐woven flax fibers were used. The stacking sequence of the fibers was in different orientations, such as 0°, +45°, and 90°. The composites manufactured had good mechanical properties. A tensile strength of about 119 MPa and Young's modulus of about 14 GPa was achieved, with flexural strength and modulus of about 201 MPa and 24 GPa, respectively. For the purposes of comparison, composites were made with a combination of woven fabrics and glass fibers. One ply of a glass fiber mat was sandwiched in the mid‐plane and this increased the tensile strength considerably to 168 MPa. Dynamic mechanical analysis was performed in order to determine the storage and loss modulus and the glass transition temperature of the composites. Microstructural analysis was done with scanning electron microscopy. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Experimental Investigation of Mechanical and Morphological Properties of Flax-Glass Fiber Reinforced Hybrid Composite using Finite Element Analysis

The use of cellulosic fibers as reinforcing materials in polymer composites has gained popularity due to an increasing trend for developing sustainable materials. In the present experimental study, flax and glass fiber reinforced partially eco-friendly hybrid composites are fabricated with two different fiber orientations of 0° and 90°. The mechanical properties of these composites such as tensile, flexural and impact strengths have been evaluated. From the experiments, it has been observed that the composites with the 0° fiber orientation can hold the maximum tensile strength of 82.71 MPa, flexural strength of 143.99 MPa, and impact strength of 4 kJ/m². Whereas the composites with 90° fiber orientation can withstand the maximum tensile strength of 75.64 MPa, flexural strength of 134.86 MPa, and impact strength of 3.99 kJ/m². Morphological analysis is carried out to analyze fiber matrix interfaces and the structure of the fractured surfaces by using scanning electron microscopy (SEM). The finite element analysis (FEA) has been carried out to predict the resulting important mechanical properties by using ANSYS 12.0. From the results it is found that the experimental results are very close to the results predicted from FEA model values. It is suggested that these hybrid composites can be used as alternate materials for pure synthetic fiber reinforced polymer composite materials.     

Mechanical and morphological properties for sandwich composites of wood/PVC and glass fiber/PVC layers

This work manufactured sandwich composites from glass fiber/poly(vinyl chloride) (GF/PVC) and wood/PVC layers, and their mechanical and morphological properties of the composites in three GF orientation angles were assessed. The effects of K value (or viscosity index) of PVC and Dioctyl phthalate (DOP) loading were of our interests. The GF/PVC was used as core layer whereas wood/PVC was the cover layers. The experimental results indicated that PVC with low K value was recommended for the GF/PVC core layer for fabrication of GF/WPVC sandwich composites. The improvement of PVC diffusion at the interface between the GF and the PVC core layer was obtained when using PVC with K value of 58. This was because it could prevent de‐lamination between composite layers which would lead to higher mechanical properties of the sandwich composites, except for the tensile modulus. The sandwich composites with 0° GF orientation possessed relatively much higher mechanical properties as compared with those with 45° and 90° GF orientations, especially for the impact strength. Low mechanical properties of the sandwich composites with 45° and 90° GF orientation angles could be overcome by incorporation of DOP plasticizer into the GF/PVC core layer with the recommended DOP loadings of 5–10 parts per hundred by weight of PVC components. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical properties of carbon fiber/epoxy composites: Effects of number of plies,fiber contents,and angle‐ply layers

Multi‐axial multi‐ply fabric (MMF) composites are becoming increasingly popular as reinforcing materials in high‐performance composites due to their high mechanical properties. This work aimed to study the effects of three variable parameters including fiber contents, numbers of plies, and layer orientations on the mechanical properties of MMF composites. Unidirectional carbon fibers and a two‐part epoxy resin were employed to produce the composite laminates using the manual lay‐up process. It was found that the mechanical properties of composites made with 5‐ply were slightly greater than 3‐ply composites. However, there was no highly significant difference between them. Generally, the angle‐ply of the composites showed the greatest effect on the mechanical properties compared with number of plies and layer orientations. The significant improvements in mechanical properties of the composites were further supported using scanning electron microscopy (SEM). Morphologies of the tensile fracture surfaces of composites revealed that the presence of fiber pulled out results in the creation of voids between the fibers and matrix polymer. This causes the mechanical properties of the composites to be reduced. Finally, the enhancement of mechanical properties of composites clearly confirmed that angle‐ply layer (0°,?35°,0°,+35°,0°) had the most significant reinforcing effect among other parameters evaluated. POLYM. ENG. SCI., 54:2676–2682, 2014. © 2013 Society of Plastics Engineers     

Mechanical characterization and modeling of poly (β‐hydroxybutyrate)‐co‐poly(β‐hydroxyvalerate)–Alfa fiber‐reinforced composites

The mechanical properties of biobased composites of poly(β‐hydroxybutyrate)‐co‐poly(β‐hydroxyvalerate) biopolymer continuously reinforced with unidirectional Alfa fibers are investigated via tensile testing of oriented composite laminates. Simple mechanical models for the elastic stiffness, strength, and nonlinear hardening of the biobased composites are proposed with an emphasis on techniques that only require the independent properties of the fiber and matrix to facilitate composite design. Rule of mixtures (ROM) approaches are found to effectively predict the elastic properties of the composites but generally overestimate strength. Modified ROM approaches that discount the contribution of the matrix in the fiber loading direction and the contribution of the fiber in the transverse loading direction provide the most accurate strength predictions. Apparent elastic properties for composites with varying fiber orientations are predicted using a modified orthotropic laminate plate method which was found to overestimate composite stiffness in off‐axis loading directions. Postyield nonlinear hardening is modeled using a calibrated continuum yield and plasticity model and demonstrated to provide a close match of the experimental results. POLYM. COMPOS., 35:1758–1766, 2014. © 2014 Society of Plastics Engineers     

Effect of fiber orientation on viscoelastic properties of polymer matrix composites subjected to thermal cycles

Fibers in polymer composites can be designed in various orientations for their usage in service life. Various fiber orientated polymer composites, which are used in aeroplane and aerospace applications, are frequently subjected to thermal cycles because of the changes in body temperatures at a range of −60 to 150°C during flights. It is an important subject to investigate the visco‐elastic properties of the thermal cycled polymer composite materials which have various fiber orientations during service life. Continuous fiber reinforced composites with a various fiber orientations are subjected to 1,000 thermal cycles between the temperatures of 0 and 100°C. Dynamic mechanic thermal analysis (DMTA) experiments are carried out by TA Q800 type equipment. The changes in glass transition temperature (T_g), storage modulus (E′), loss modulus (E′′) and loss factor (tan δ) are inspected as a function of thermal cycles for different fiber orientations. It was observed that thermal and dynamic mechanical properties of the polymer composites were remarkably changed by thermal cycles. It was also determined that the composites with [45°/−45°]_s fiber orientation presented the lowest dynamic mechanical properties. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Effect of stress transfer between fiber and matrix on toughness of polymer composite

Thanks to their lightweight properties, formability and low cost, polymers have become an essential material for manufactured products. To improve the mechanical properties, almost all polymers are blended with some kind of fiber made from glass, carbon, organic or natural material. The importance of interfacial strength between matrix and fiber is a well known requirement for effective mechanical properties and some experimental results indicate that low interfacial strength helps increase the toughness of composites. In this paper, models of composite reinforced by fiber aligned with maximum principal stress under uni‐tensile loading are simulated. Based on the simulation result, we discuss the effect of interfacial strength, aspect ratio of fiber and friction force between matrix and fiber on stable deformation and provide the guidelines for establishing composites with high modulus and toughness. POLYM. COMPOS. 2011. © 2011 Society of Plastics Engineers     

Mechanical,Electrical and Water Absorption Study of Jute/Glass/Jute-bamboo/Glass-bamboo-bisphenol-C-formaldehyde-acrylate a Value Added Composites

Bisphenol-C-formaldehyde-acrylate (BCFA) resin was synthesized by reacting 0.1 mol bisphenol-C-formaldehyde resin, 0.4 mol acrylic acid in 25 ml 1,4-dioxane and 1.5 g phenothiazine catalyst at 80°C for 6 h. Jute, glass, jute-bamboo, and glass-bamboo composites were prepared by compression molding technique at 150°C for 2 h under 30.4 MPa pressure. Jute-BCFA, Glass-BCFA, Jute-bamboo-BCFA, Glass-Bamboo-BCFA possess 50, 114, 49, and 65 MPa tensile strength; 58, 185, 69, and 70 MPa flexural strength; 1.2, 3.3, 1.3, and 1.9 kV/mm electric strength and 6.2 × 10¹², 2.5 × 10¹³, 6.6 × 10¹², and 1.5 × 10¹³ ohm cm volume resistivity. The data are interpreted in terms of nature of fibers and resin and fiber loading and orientation. Water absorption behavior of composites is tested in pure water, 10% NaCl and 10% Hcl solutions at room temperature as well as in boiling water. Observed diffusivity order for each of composite is H₂O < NaCl < HCl. Sandwich composites shown high water absorption in all media due to high bamboo fiber loading and fiber agglomeration. The presence of HCl and NaCl affected the water structure and hence diffusivity. Jute-bamboo-BCFA and Glass-Bamboo-BCFA delaminated in boiling water within half an hour. Mechanical and electrical properties and water absorption behavior are affected by the nature of fibers and matrix, fiber loading and fiber arrangement. Fairly good mechanical and electrical properties of Jute-BCFA and Glass-BCFA and their low water absorption behavior signify their usefulness as low load bearing applications. Composites signify their use for low load bearing applications in construction, electrical and marine industries.     

Effect of the fiber orientation on the sorption kinetics of seawater in an epoxy/glass composite: A free-volume microprobe study

The conventional gravimetric method and positron lifetime spectroscopy have been used to investigate the effect of glass fiber orientation on the diffusion behavior of seawater in epoxy-based composite samples with glass fiber orientations of 0 and 45°. The equilibrium mass uptake of seawater in 45 and 0° orientation composites has been found to be 2.77 and 1.57%, respectively. The diffusion process is non-Fickian in a 45° fiber oriented composite, whereas it is Fickian in a 0° oriented composite. Free-volume data for 45° fiber oriented composites indicates swelling upon the sorption of seawater leading to structural relaxation, and hence the diffusion becomes non-Fickian. On the other hand, a 0° fiber orientation sample exhibits no swelling, and this suggests that water diffusion to the fiber–resin interface through the resin matrix is impeded by the large number of bonds. A polymer–fiber interaction parameter determined from these results also further supports the idea that interface interaction in a 45° fiber oriented composite is less than that in a 0° fiber oriented composite. Positron and gravimetric results support this argument. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical properties of pineapple leaf fiber-reinforced polyester composites

Pineapple leaf fiber (PALF) which is rich in cellulose, relatively inexpensive, and abundantly available has the potential for polymer reinforcement. The present study investigated the tensile, flexural, and impact behavior of PALF-reinforced polyester composites as a function of fiber loading, fiber length, and fiber surface modification. The tensile strength and Young's modulus of the composites were found to increase with fiber content in accordance with the rule of mixtures. The elongation at break of the composites exhibits an increase by the introduction of fiber. The mechanical properties are optimum at a fiber length of 30 mm. The flexural stiffness and flexural strength of the composites with a 30% fiber weight fraction are 2.76 GPa and 80.2 MPa, respectively. The specific flexural stiffness of the composite is about 2.3 times greater than that of neat polyester resin. The work of fracture (impact strength) of the composite with 30% fiber content was found to be 24 kJ m⁻². Significant improvement in the tensile strength was observed for composites with silane A172-treated fibers. Scanning electron microscopic studies were carried out to understand the fiber-matrix adhesion, fiber breakage, and failure topography. The PALF polyester composites possess superior mechanical properties compared to other cellulose-based natural fiber composites. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 1739–1748, 1997     

Mechanical Properties of Benzoylated Oil Palm Empty Fruit Bunch Short Fiber Reinforced Poly(vinyl chloride) Composites

The influence of untreated and benzoylated oil palm empty fruit bunch (OPEFB) short fiber loading on the mechanical properties of the poly(vinyl chloride) (PVC) composite was studied. Benzoylated OPEFB was produced by mixing OPEFB with NaOH solution and agitating vigorously with benzoyl chloride. The PVC resin, various additives, and OPEFB were first dry blended using a laboratory mixer before being milled into sheets on a two-roll mill at 165°C and then hot pressed into composite samples at 180°C. The tensile and impact strength of untreated and benzoylated OPEFB composites decreased whereas the tensile modulus increased with increasing fiber loading from 0 to 40 phr. However, the benzoylated OPEFB was able to improve the tensile properties and impact strength of composites when compared to the untreated fiber. The enhancement of mechanical properties showed that the treatment improved the OPEFB fiber-PVC matrix interfacial adhesion. The improvement of adhesion was clarified by SEM micrographs, the increase of water resistance, and the reduction of glass transition temperature of the composites.     

Short fiber-reinforced oxide fiber composites

This paper presents a novel fiber spraying process for the manufacturing of short fiber bundle-reinforced Nextel™ 610/Al₂O₃-ZrO₂ oxide fiber composites (SF-OFC) and its characterization. First, the influence of varying fiber lengths (7, 14, and 28 mm, continuous fibers) and fiber orientations (unidirectional 0°, quasi-isotropic, ±45°) was investigated using hand-laid SF-OFC. Due to the weak matrix, the hand-laid material exhibited a strongly fiber-dominated material behavior, that is, variations in fiber length and orientation had a strong influence on the material properties. Second, the automated sprayed SF-OFC, however, exhibited a random orientation of the fiber bundles, which resulted in in-plane isotropic material properties. Average bending strengths of up to 177 MPa, strains of .39%, and a quasi-ductile fracture behavior were achieved. The strain was, therefore, in the range of fabric-reinforced OFC. While the bending strength of the SF-OFC was somewhat lower than that of fabric-reinforced OFC with the fiber orientation parallel to the loading direction, it was more than two times higher than the strength in 45° direction relative to the fabric reinforcement. Combined with good drapability and lower material costs compared to fabric-reinforced OFC, SF-OFC is, therefore, a promising material for industrial applications.     

Short pineapple-leaf-fiber-reinforced low-density polyethylene composites

Short pineapple-leaf-fiber-(PALF)-reinforced low-density polyethylene (LDPE) composites were prepared by melt-mixing and solution-mixing methods. In the melt-mixing technique, a mixing time of 6 min, rotor speed of 60 rpm, and mixing temperature of 130°C were found to be the optimum conditions. Tensile properties of melt-mixed and solution-mixed composites were compared. Solution-mixed composites showed better properties than melt-mixed composites. The influence of fiber length, fiber loading, and orientation on the mechanical properties has also been evaluated. Fiber breakage and damage during processing were analyzed from fiber distribution curve and optical and scanning electron micrographs. Considering the overall mechanical properties and processability characteristics, fiber lenght of 6 mm was found to be the optimum length of pineapple leaf fiber for the reinforcement in LDPE. The mechanical properties were found to be enhanced and elongation at break reduced with increasing fiber loading. Longitudinally oriented composites showed better properties than randomly and transversely oriented composites. Recyclability of the composite was found to be very good. A comparison of the properties of the PALF-reinforced LDPE composites with those of other cellulose-fiber-reinforced LDPE systems indicated superior performance of the PALF–LDPE composites.© 1995 John Wiley & Sons. Inc.     

Mechanical and viscoelastic properties of soybean oil thermoset reinforced with jute fabrics and carded lyocell fiber

Composites and hybrid composites were manufactured from renewable materials based on jute fibers, regenerated cellulose fibers (Lyocell), and thermosetting polymer from soybean oil. Three different types of jute fabrics with biaxial weave architecture but different surface weights, and carded Lyocell fiber were used as reinforcements. Hybrid composites were also manufactured by combining the jute reinforcements with the Lyocell. The Lyocell composite was found to have better mechanical properties than other composites. It has tensile strength and modulus of about 144 MPa and 18 GPa, respectively. The jute composites also have relatively good mechanical properties, as their tensile strengths and moduli were found to be between 65 and 84 MPa, and between 14 and 19 GPa, respectively. The Lyocell‐reinforced composite showed the highest flexural strength and modulus, of about 217 MPa and 13 GPa, respectively. In all cases, the hybrid composites in this study showed improved mechanical properties but lower storage modulus. The Lyocell fiber gave the highest impact strength of about 35 kJ/m², which could be a result of its morphology. Dynamic mechanical analysis showed that the Lyocell reinforced composite has the best viscoelastic properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Comparison of mechanical properties of epoxy composites reinforced with stitched glass and carbon fabrics: Characterization of mechanical anisotropy in composites and investigation on the interaction between fiber and epoxy matrix

The primary purpose of the study is to evaluate and compare the mechanical properties of epoxy‐based composites having different fiber reinforcements. Glass and carbon fiber composite laminates were manufactured by vacuum infusion of epoxy resin into two commonly used noncrimp stitched fabric (NCF) types: unidirectional and biaxial fabrics. The effects of geometric variables on composite structural integrity and strength were illustrated. Hence, tensile and three‐point bending flexural tests were conducted up to failure on specimens strengthened with different layouts of fibrous plies in NCF. In this article, an important practical problem in fibrous composites, interlaminar shear strength as measured in short beam shear test, is discussed. The fabric composites were tested in three directions: at 0°, 45°, and 90°. In addition to the extensive efforts in elucidating the variation in the mechanical properties of noncrimp glass and carbon fabric reinforced laminates, the work presented here focuses, also, on the type of interactions that are established between fiber and epoxy matrix. The experiments, in conjunction with scanning electron photomicrographs of fractured surfaces of composites, were interpreted in an attempt to explain the failure mechanisms in the composite laminates broken in tension. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Physical,mechanical, and water absorption behavior of coir/glass fiber reinforced epoxy based hybrid composites

Fiber reinforced polymer composites has been used in a variety of application because of their many advantages such as relatively low cost of production, easy to fabricate, and superior strength compare to neat polymer resins. Reinforcement in polymer is either synthetic or natural. Synthetic fiber such as glass, carbon, etc. has high specific strength but their fields of application are limited due to higher cost of production. Recently there is an increase interest in natural composites which are made by reinforcement of natural fiber. In this connection, an investigation has been carried out to make better utilization of coconut coir fiber for making value added products. The objective of the present research work is to study the physical, mechanical, and water absorption behavior of coir/glass fiber reinforced epoxy based hybrid composites. The effect of fiber loading and length on mechanical properties like tensile strength, flexural strength, and hardness of composites is studied. The experimental results reveal that the maximum strength properties is observed for the composite with 10 wt% fiber loading at 15 mm length. The maximum flexural strength of 63 MPa is observed for composites with 10 wt% fiber loading at 15 mm fiber length. Similarly, the maximum hardness value of 21.3 Hv is obtained for composites with 10 wt% fiber loading at 20 mm fiber length. Also, the surface morphology of fractured surfaces after tensile testing is examined using scanning electron microscope (SEM). POLYM. COMPOS., 35:925–930, 2014. © 2013 Society of Plastics Engineers     

Green Composites from Natural Rubber and Oil Palm Fiber: Physical and Mechanical Properties

Natural rubber (NR) composites were prepared by incorporating short oil palm fibers of different lengths (viz., 2, 6, 10, and 14 mm) into natural rubber matrix in a mixing mill according to a base formulation. The curing characteristics of the mixes were studied and the samples were vulcanized at 150°C. The vulcanization parameters, processability characteristics, and tensile properties of these composites were analyzed. The effects of fiber length, orientation, loading, and fiber-matrix interaction on the mechanical properties of the green composites were studied. The reinforcement property of the alkali-treated fiber was compared with that of the untreated one. The extent of fiber orientation was studied from green strength measurements. From anisotropic swelling studies, the extent of fiber alignment and the strength of fiber–rubber interface adhesion were analyzed. Scanning electron microscopic (SEM) studies were carried out to analyze the fiber surface morphology, fiber pullout, and fiber–rubber interface.     

Mechanical behavior and fracture toughness characterization of high strength fiber reinforced polymer textile composites

The mechanical and fracture behavior of polymer composites are the subject of great interest from many years and still interesting among the researchers. Composites are extremely used for their superior mechanical, thermal and fracture toughness properties in various sectors such as automobile, aerospace and defense applications. In this article, unidirectional and woven high strength glass, carbon and Kevlar fiber reinforced polymer textile composites are taken into consideration for the comprehensive review of mechanical behavior and fracture toughness characterization. Current review work began with the introduction to polymer textile composites with its manufacturing stages, processing techniques and factors affecting the performance under mechanical loading. The mechanical behavior of high strength fiber reinforced polymer (HSFRP) textile composites was discussed in tension, compression, flexural, low velocity and high velocity impact loading with the recent numerical and experimental characterization studies. Textile geometrical modeling and CAE tools are also described for numerical characterization. Under the influence of mechanical loading on composites, failure occurs actually due to the crack initiation and propagation, so it is also required to characterize. Significant elements of fracture mechanics are well described for the better understanding of fracture toughness characterization. Mode-I, Mode-II, Mode-III interlaminar and Mode-I intralaminar fracture toughness characterization are widely explained by considering the effect of filler content, fiber orientation and fiber volume fraction. Fracture toughness characterization techniques and research summery are uniquely presented by considering various factors under one umbrella for better understanding of fracture behavior. Statistical Weibull distribution is also presented for the failure prediction of composites.

     

Effect of fiber orientation on surface characteristics of C/SiC composites by laser-assisted machining

In this paper, the characteristics and mechanism of laser-assisted machining (LAM) of C/SiC composites with different fiber orientations (0°, 45°, 90°, 135°) are studied. For the purpose of this study, a series of LAM experiments have been carried out and supported by a comparative analysis over the conventional machining (CM). Furthermore, the effect of fiber orientation on surface morphology, roughness, and sub-surface damage was explored. It is found that the surface quality of the workpiece treated by LAM is better than that of CM, and a lower surface roughness Ra value is obtained. It is shown that depending on different fiber orientations, the surface roughness decreases in different degrees. The roughness at 90° fiber orientation witnesses the maximum reduction, followed by 0° and 45° fiber orientation, and the roughness at 135° fiber orientation undergoes the slightest reduction. Moreover, surface micro-defects under LAM are significantly reduced, and fiber fractures are tidier. On the other hand, the matrix is mixed with fiber debris under high temperatures and sticks to the machined surface, filling and repairing surface pits and holes and hence improving the processed surface quality. These results provide new guidance for improving the machining quality of C/SiC composites.     

Solid freeform fabrication of soybean oil-based composites reinforced with clay and fibers

Soybean oil/epoxy-based composites were prepared by an extrusion freeform fabrication method. These composites were reinforced with a combination of organically modified clay and fibers. The intercalated behavior of the epoxy resin in the presence of organo-modified clay was investigated by X-ray diffraction and transmission electron microscopy. The mixture of epoxidized soybean oil and EPON^® 828 resin was modified with a gelling agent to solidify the materials until curing occurred. The flexural modulus reached 4.86 GPa with glass fiber reinforcement at 50.6 wt% loading. It was shown that the fiber orientation followed the direction of motion of the writing head that deposited the resins and had an influence on the properties of the composite. The composites cured by curing agent jeffamine EDR-148 were found to have lower mechanical properties than those cured with triethylenetetramine, diethylenetriamine, and polyethylenimine. In addition, the effects of clay loading and fiber loading on mechanical properties of the composites were studied and reported.