Dynamic mechanical analysis of pineapple leaf/glass hybrid fiber reinforced polyester composites

The dynamic mechanical properties of randomly oriented intimately mixed hybrid composites based on pineapple leaf fibers (PALF) and glass fibers (GF) in unsaturated polyester (PER) matrix were investigated. The PALFs have high‐specific strength and improve the mechanical properties of the PER matrix. In this study, the volume ratio of the two fibers was varied by incorporating small amounts of GF such as PALF/GF, 90/10, 80/20, 70/30, and 50/50, keeping the total fiber loading constant at 40 wt%. The dynamic modulus of the compositeswas found to increase on GF addition. The intimately mixed (IM) hybrid composites with PALF/GF, 80/20 (0.2 V_f GF) showed highest E′ values and least damping. Interestingly, the impact strength of the composites was minimum at this volume ratio. The composites with 0.46 V_f GF or PALF/GF (50/50) showed maximum damping behavior and highest impact strength. The results were compared with hybrid composites of different layering patterns such as GPG (GF skin and PALF core) and PGP (PALF skin and GF core). IM and GPG hybrid composites are found more effective than PGP. The activation energy values for the relaxation processes in different composites were calculated. The overall results showed that hybridization with GF enhanced the performance properties. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Pineapple leaf fiber reinforced thermoplastic composites: Effects of fiber length and fiber content on their characteristics

Pineapple leaf fiber (PALF) was used as a reinforcement in polyolefins. Polypropylene (PP) and low‐density polyethylene (LDPE) composites with different fiber lengths (long and short fibers) and fiber contents (0–25%) were prepared and characterized. The results showed that the tensile strength of the composites increased when the PALF contents were increased. It was observed that the composites containing long fiber PALF were stronger than the short fiber composites as determined by greater tensile strength. An SEM study on the tensile fractured surface confirmed the homogeneous dispersion of the long fibers in the polymer matrixes better than dispersion of the short fibers. The unidirectional arrangement of the long fibers provided good interfacial bonding between the PALF and polymer which was a crucial factor in achieving high strength composites. Reduction in crystallinity of the composites, as evident from XRD and DSC studies suggested that the reinforcing effect of PALF played an important role in enhancing their mechanical strength. From the rule of mixtures, the stress efficiency factors of the composite strength could be calculated. The stress efficiency factors of LDPE were greater than those of PP. This would possibly explain why the high modulus fiber (PALF) had better load transfers to the ductile matrix of LDPE than the brittle matrix of PP. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Poly(lactic acid)/Phormium tenax composites: Morphology and thermo‐mechanical behavior

Composites of Phormium tenax fibers in a poly(lactic acid) matrix with fiber content of up to 40 wt%, produced by injection molding and twin screw compounding, were characterized by scanning electron microscopy, differential scanning calorimetry, thermogravimetric analysis, and mechanical tests (static and dynamic). Thermal analysis showed that cold‐crystallization peak shifted to lower temperatures with increasing fiber content, confirming that the addition of Phormium fiber has the effect of promoting crystallinity. Dynamic mechanical analysis (DMA) results showed that the addition of Phormium fiber did not affect significantly the T_g of the polymer and the area under the tan δ decreased with the addition of Phormium fiber. Tensile modulus has been consistently increased by reinforcing the composite with growing amounts of fibers, whilst the effect on tensile strength is less evident. SEM micrographs of fracture surfaces allowed highlighting failure modes of the composites, which included a diffuse presence of fiber pull‐out and debonding. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

A dynamic mechanical study on unidirectional carbon fiber-reinforced polypropylene composites

Fiber-reinforced polymer composites show high specific strength and stiffness. The alignment of reinforcing fibers results in anisotropy of the material. This anisotropic behavior has been studied through dynamic mechanical analysis of unidirectional carbon fiber-reinforced polypropylene (CFRPP) composites measured in both parallel and transverse directions to fiber arrangement. Several parameters such as storage modulus (E′), loss modulus (E″), loss factor or damping factor (tan δ), and complex viscosity (MU^*) have been determined over a wide range of frequencies and at a fixed temperature. Relaxation and retardation spectra have been constructed for these composites. Modulus enhancement occurs due to stiffness imparted by the fiber and efficient stress transfer at the interface. Relaxation of the polymer matrix ceases with increase in the volume fraction of the fibers. α′-relaxation is observed for the composite having a 13% volume fraction of fibers and is ascribed to relaxation in the crystalline phase where the additional crystallinity arises out of the transcrystalline growth at the fiber–matrix interface. There exists a good correlation between theroretical curves with the experimental ones. Relaxation and retardation spectra and the dynamic parameters determined for these composites show a good correlation with the volume fraction of fibers as well as the direction of the applied load. © 1994 John Wiley & Sons, Inc.     

Influence of varying fiber lengths on mechanical,thermal, and morphological properties of MA‐g‐PP compatibilized and chemically modified short pineapple leaf fiber reinforced polypropylene composites

Environmentally benign, low cost and abundantly available short pineapple leaf fibers (PALF), found mostly in the Tropical rain forest climates are ideal materials for manufacture of thermoplastic polymer‐matrix composites. Here, mechanical and thermal properties of composites of maleic anhydride grafted polypropylene (MA‐g‐PP) and chemically modified short PALF are studied as a function of different fiber lengths at 10 vol % fibers loading with fiber orientation in the longitudinal direction. The effects of fiber lengths and fiber loading on the morphological properties are assessed via observations by scanning electron microscopy. Fiber length of 6 mm oriented longitudinally at 10 vol % fibers loading in PP is the optimum and recommended composition, where 73% increase in impact properties, 37% increase in the flexural modulus, 33% increase in flexural strength, and 14% increase in vicat softening temperature are observed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The correlation between packing efficiency and tensile properties for polymer composites in SMC formulation

For polymer composites that find application as sheet-molding compounds (SMCs), the fiber aspect ratio l/d and the size ratio R (the ratio of the diameter of the spherical filler and the diameter of the fiber) are important parameters. A study of various composite formulations of different combinations of l/d and R has been made to examine the correlation between the packing efficiency of these fibers and fillers in air, and the properties of resulting composites. Samples containing a total of 32 wt% fibers and spherical fillers (in 1:3 proportion) were tested. The tensile modulus was seen to represent behavior similar to packing efficiency. Sources of experimental errors are discussed.     

Preparation,characterization, and mechanical properties of poly(ε‐caprolactone)/polylactic acid blend composites

Mechanical properties of poly(ε‐caprolactone) (PCL) and polylactic acid (PLA) blend reinforced with Dura and Tenera palm press fibers were studied. Dicumyl peroxide (DCP) was used as compatibilizer in the blend composites. Fourier transforms infrared spectrophotometer (FTIR) and field emission scanning electron microscope (FESEM) was used to study the effect of treatment on the fibers and fiber/matrix adhesion respectively. The uncompatibilized blend composites exhibited higher Young's modulus than the compatibilized blend composites. Impact strength of compatibilized blend composites of Tenera fibers (FM) increased by 161% at 10 wt% fiber load more than the uncompatibilized blend composites at same fiber load. The Dura fibers (FN) enhanced impact strength by 133% at 10 wt% fiber load. Tensile strength increased by 40% for compatibilized FM blend composites. In conclusion, it was observed that DCP incorporation resulted in good interfacial adhesion as revealed by the FESEM micrographs and evidenced in the improved mechanical properties. POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

短切碳纤维对聚苯腈/碳纤维复合材料性能的影响

利用碳纤维（CF）增强聚苯腈（PN）树脂制备一系列PN/CF复合材料,利用万能试验机和动态热机械分析仪（DMA）,研究短CF含量、长度与偶联剂种类对PN树脂力学性能的影响。结果表明,采用苯基三乙氧基硅烷作为偶联剂时力学性能和热稳定性达到最佳水平,相较于未经偶联剂改性PN/CF复合材料的储能模量提高了22.2%,热失重5%温度（Td5%）提高了33.1%;随着CF掺杂量的增加,材料力学性能呈现先增大后减小趋势,在0.3%（质量分数,下同）时获得了最优异力学性能,相较于PN树脂,其弯曲强度提高了38.4%,弯曲模量提升了97.7%;CF长度为6 mm时材料的弯曲强度和储能模量优于CF长度为3 mm时的材料。     

Fundamental studies on wood–plastic composites: Effects of fiber concentration and mixing temperature on the mechanical properties of poplar/PP composite

Wood fibers are increasingly being used as reinforcement in commercial thermoplastic composites due to their low cost, high specific properties and renewable nature. The ultimate goal of our research was to find a fundamental understanding of the mechanical behavior of poplar/polypropylene (PP) composites. The effect of wood fiber concentrations and mixing temperature on the mechanical properties of composites, prepared by using MAPP as the coupling agent, was investigated. In the sample preparation, four levels of fiber loading (10, 20, 30, and 40 wt%) and three compounding temperatures (180, 190, and 200^oC) were used. Most major changes in composite performance occurred at fiber contents above 30%. The results clearly showed that the fiber loading of 30 and 40 wt% at 190^oC was provided adequate reinforcement to increase the tensile and flexural strength of the PP powder. The modulus also increased with increasing the fiber content, because poplar fibers are believed to be more rigid than polymer. However the addition of wood fibers resulted in a decrease in elongation and impact properties of the composites. The FTIR spectroscopy showed that the copolymer was bonded to the fibers by ester linkages and hydrogen bonds at 1705–1735 cm⁻¹. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Extremely oriented tunicin whiskers in poly(vinyl alcohol) nanocomposites

In order to utilize the excellent mechanical properties of cellulose whiskers (CWs) along their length, the present work was undertaken to embed CWs with highly oriented forms in a polymer matrix. Nanocomposite fibers were prepared using poly(vinyl alcohol) (PVA; degree of polymerization of 1500) as the matrix and a stable aqueous suspension of CWs extracted from tunicates as the reinforcing phase. Macroscopically homogeneous suspensions of PVA–CW were gel‐spun in a methanol coagulating bath. The as‐spun fibers included CWs oriented along the fiber axis and showed a significant increase in dynamic storage modulus. Hot drawing of the PVA–CW as‐spun fibers to their maximal draw ratio led to extremely high orientation of the CWs together with a drastic reduction in voids in the fiber matrix. Outstanding mechanical properties of the drawn composites were obtained by the incorporation of only a small amount (1 wt% of solid PVA content) of CWs. The stress transfer mechanism in the fibers was studied using an X‐ray diffraction technique by applying stress to the whole composite with in situ monitoring of stress on the incorporated CWs. The applied external stress was found to be translated efficiently to the incorporated CWs through the PVA matrix, suggesting strong interfacial bonding between filler and matrix. The strong interaction and efficient stress transfer between matrix and filler are suggested as the cause for the observed improvements in mechanical properties of the composites. Copyright © 2011 Society of Chemical Industry     

Dynamic mechanical properties of sisal fiber reinforced polyester composites fabricated by resin transfer molding

The dynamic mechanical properties of sisal fiber reinforced polyester composites fabricated by resin transfer molding (RTM) were investigated as a function of fiber content, frequency, and temperature. Investigation proved that at all temperature range the storage modulus (E′) value is maximum for the composites having fiber loading of 40 vol%. The loss modulus (E″) and damping peaks (tan δ) were lowered with increasing fiber content. The height of the damping peaks depends upon the fiber content and the fiber/matrix adhesion. The extent of the reinforcement was estimated from the experimental storage modulus, and it has been found that the effect of reinforcement is maximum at 40 vol% fiber content. As the fiber content increases the T_g from tan δ curve showed a positive shift. The loss modulus, storage modulus, and damping peaks were evaluated as a function of frequency. The activation energy for the glass transition increases upon the fiber content. Cole–Cole analysis was made to understand the phase behavior of the fiber reinforced composites. Finally, attempts were made to correlate the experimental dynamic properties with theoretical predictions. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Influence of interfacial adhesion on the structural and mechanical behavior of PP‐banana/glass hybrid composites

Hybrid composites of polypropylene (PP), reinforced with short banana and glass fibers were fabricated using Haake torque rheocord followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both fibers into PP matrix resulted in increase of tensile strength, flexural strength, and impact strength upto 30 wt% with an optimum strength observed at 2 wt% MAPP treated 15 wt% banana and 15 wt% glass fiber. The rate of water absorption for the hybrid composites was decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has been analyzed to investigate the interfacial properties. An increase in storage modulus (E′) of the treated‐composite indicates higher stiffness. The loss tangent (tan δ) spectra confirms a strong influence of fiber loading and coupling agent concentration on the α and β relaxation process of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out through differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA), indicated an increase in the crystallization temperature and thermal stability of PP with the incorporation of MAPP‐treated banana and glass fiber. POLYM. COMPOS., 31:1247–1257, 2010. © 2009 Society of Plastics Engineers     

A comparative study on the mechanical and degradation properties of plant fibers reinforced polyethylene composites

Coir and abaca fiber‐reinforced linear low density polyethylene (LLDPE) composites (30 wt% fiber) were prepared by compression molding. Coir and abaca fibers were treated with methyl methacrylate (MMA) using ultraviolet radiation to improve the mechanical properties of the composites. Concentration of MMA and radiation dose was optimized. It was found that 30% MMA in methanol along with photoinitiator Darocur‐1173 (2%) and 15th pass of radiation rendered better performance. Chemically treated fiber‐reinforced specimens yielded better mechanical properties compared to the untreated composites, whereas coir fiber composites had better mechanical properties than abaca fiber reinforced ones. For the improvement of the properties, optimized coir (coir fiber treated with 30% MMA) and abaca (abaca fiber treated with 40% MMA) fibers were again treated with aqueous starch solution (2%–8%, w/w) for 2–7 min. Composites made of 3%‐starch‐treated coir fiber (5 min soaking time) showed the best mechanical properties than that of abaca‐fiber‐based composites. Water uptake and soil degradation tests of the composites were also performed. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Mechanical properties of pineapple leaf fiber-reinforced polyester composites

Pineapple leaf fiber (PALF) which is rich in cellulose, relatively inexpensive, and abundantly available has the potential for polymer reinforcement. The present study investigated the tensile, flexural, and impact behavior of PALF-reinforced polyester composites as a function of fiber loading, fiber length, and fiber surface modification. The tensile strength and Young's modulus of the composites were found to increase with fiber content in accordance with the rule of mixtures. The elongation at break of the composites exhibits an increase by the introduction of fiber. The mechanical properties are optimum at a fiber length of 30 mm. The flexural stiffness and flexural strength of the composites with a 30% fiber weight fraction are 2.76 GPa and 80.2 MPa, respectively. The specific flexural stiffness of the composite is about 2.3 times greater than that of neat polyester resin. The work of fracture (impact strength) of the composite with 30% fiber content was found to be 24 kJ m⁻². Significant improvement in the tensile strength was observed for composites with silane A172-treated fibers. Scanning electron microscopic studies were carried out to understand the fiber-matrix adhesion, fiber breakage, and failure topography. The PALF polyester composites possess superior mechanical properties compared to other cellulose-based natural fiber composites. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 1739–1748, 1997     

Effect of fiber orientation on viscoelastic properties of polymer matrix composites subjected to thermal cycles

Fibers in polymer composites can be designed in various orientations for their usage in service life. Various fiber orientated polymer composites, which are used in aeroplane and aerospace applications, are frequently subjected to thermal cycles because of the changes in body temperatures at a range of −60 to 150°C during flights. It is an important subject to investigate the visco‐elastic properties of the thermal cycled polymer composite materials which have various fiber orientations during service life. Continuous fiber reinforced composites with a various fiber orientations are subjected to 1,000 thermal cycles between the temperatures of 0 and 100°C. Dynamic mechanic thermal analysis (DMTA) experiments are carried out by TA Q800 type equipment. The changes in glass transition temperature (T_g), storage modulus (E′), loss modulus (E′′) and loss factor (tan δ) are inspected as a function of thermal cycles for different fiber orientations. It was observed that thermal and dynamic mechanical properties of the polymer composites were remarkably changed by thermal cycles. It was also determined that the composites with [45°/−45°]_s fiber orientation presented the lowest dynamic mechanical properties. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Influence of organically modified nanoclay on the performance of pineapple leaf fiber‐reinforced polypropylene nanocomposites

Polypropylene/Pine apple leaf fiber (PP/PALF)‐reinforced nanocomposites were fabricated using melt blending technique in a twin‐screw extruder (Haake Rheocord 9000). Variation in mechanical properties, crystallization behavior, water absorption, and thermal stability with the addition of nanoclay in PP/PALF composites were investigated. It was observed that the tensile, flexural, and impact properties of PP increase with the increase in fiber loading from 10 to 30 wt %. Composites prepared using 30 wt % PALF and 5 wt % MA‐g‐PP exhibited optimum mechanical performance with an increase in tensile strength to 31%, flexural strength to 45% when compared with virgin PP. Addition of nanoclay results in a further increase in tensile and flexural strength of PP/PALF composites to 20 and 24.3%, which shows intercalated morphology. However, addition of nanoclay does not show any substantial increase in impact strength when compared with PP/PALF composites. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), confirming a strong influence between the fiber/nanoclay and MA‐g‐PP. Differential scanning calorimetry, thermogravimetric analysis thermograms also showed improved thermal properties when compared with the virgin matrix. TEM micrographs also showed few layers of agglomerated clay galleries along with mixed nanomorphology in the nanocomposites. Wide angle X‐ray diffraction studies indicated an increase in d‐spacing from 22.4 Å in Cloisite 20A to 40.1 Å in PP/PALF nanocomposite because of improved intercalated morphology. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermo‐mechanical behavior of polyamide 12—polyamide 66 recycled fiber composites

Postconsumed polyamide 66 (PA66) short fibers derived from carpets were utilized as reinforcement in a commercial polyamide (PA12) matrix at different concentrations, ranging from 10 wt% to 30 wt%, in order to evaluate the effect of PA66 content on the mechanical and dynamic behavior of the resulting materials. DSC tests revealed that both melting and crystallization behavior of PA12 matrix was slightly affected by the presence of the fibers, showing a somewhat nucleation effect of PA66. Quasi‐static tensile tests evidenced that the introduction of PA66 fibers provided a slight stiffening effect on the resulting composites, increasing the elastic modulus with the filler content, especially at testing temperatures above T_g. On the other hand, the presence of agglomerated fibers led to an embrittlement of polyamide composites, showing a significant reduction of the tensile properties at break increasing the PA66 fibers content. Tensile dynamic tests confirmed the stiffening effect provided by the recycled fibers, increasing both dynamic moduli (E′ and E″) with PA66 content over the whole range of considered temperatures. Glass transition temperature of PA12 was substantially increased by the presence of the fibers, while the coefficient of linear thermal expansion above T_g was progressively reduced with the filler content. Interestingly, isothermal creep compliance of the material above T_g was substantially reduced by the presence of PA66 fibers. Morphological analysis on the cryofractured surfaces revealed a quite good fiber‐matrix interfacial adhesion, with the presence of some nucleating phenomena on the pulled out surfaces. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Effect of cloisite 30B clay and sisal fiber on dynamic mechanical and fracture behavior of unsaturated polyester toughened epoxy network

This study examined the dynamic mechanical properties of sisal fiber reinforced unsaturated polyester (UP) toughened epoxy nanocomposites. The chemical structures changes in Epoxy, UP and UP toughened epoxy (Epoxy/UP) systems were characterized by Proton Nuclear magnetic resonance (¹HNMR) spectroscopy. The morphological alterations of the nanocomposites were analyzed by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The untreated, chemically treated fibers, nanoclays, and the fiber reinforced Epoxy/UP nanocomposites were confirmed by FTIR spectrometer. The obtained mechanical results showed that alkali‐silane treated fibers improve the tensile strength (96%) and flexural strength (60%) of the Epoxy/UP nanocomposite than that of Epoxy/UP blend due to the strong interfacial bonding between the sisal fiber and matrix. The fracture toughness (K_IC) and fracture energy (G_IC) of treated sisal fiber reinforced DGEBA/UP/C30B nanocomposites found to be higher than that of untreated sisal fiber nanocomposites. The dynamic mechanical analysis (DMA) reveals that the fiber reinforced Epoxy/UP nanocomposites contains 30 wt% treated fiber and 1 wt% nanoclays, exhibits the highest storage modulus and better glass transition temperature (T_g) among the other kind of systems. The surface morphology of the fibers, fractured surface of the resins and composites were confirmed by scanning electron microscope (SEM). POLYM. COMPOS., 37:2832–2846, 2016. © 2015 Society of Plastics Engineers     

Dynamic mechanical thermal analysis of biocomposites based on PLA and PHBV—A comparative study to PP counterparts

The primary objective of this study was the investigation of thermo‐mechanical behavior of cellulosic fiber reinforced polylactid (PLA) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) biopolymers. Both PLA and PHBV were processed with 30 wt % of cellulosic fibers; moreover, to improve the processability and mechanical performance, PHBV was previously blended with 30% by weight poly(butylene adipate‐co‐butylene terephthalate) (PBAT). Secondary target was the comparison of the obtained results to natural fiber reinforced polypropylene (PP) composites reinforced with exact the same fibers and processed by using identical techniques. For validation the thermo‐mechanical properties, a dynamic mechanical thermal analysis (DMTA) was applied. Storage modulus (E′), loss modulus (E″), and loss factor (tan δ) were determined. The DMTA results indicate decreased polymer chain motion with resulting improvement of stiffness expressed by the storage modulus. Finally, the effectiveness of fiber on the moduli was investigated. The C coefficient differs in dependence on fiber type, use of coupling agent, and the reference temperature in glassy state. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3175–3183, 2013     

Effect of natural fibers on thermal and mechanical properties of natural fiber polypropylene composites studied by dynamic mechanical analysis

The present study deals with the effects of natural fibers on thermal and mechanical properties of natural fiber polypropylene composites using dynamic mechanical analysis. Composites of polypropylene and various natural fibers including kenaf fibers, wood flour, rice hulls, and newsprint fibers were prepared at 25 and 50% (by weight) fiber content levels. One and two percent maleic anhydride grafted polypropylene was also used as the compatibilizer for composites containing 25 and 50% fibers, respectively. Specimens for dynamic mechanical analysis tests were cut out of injection‐molded samples and were tested over a temperature range of ?60 to +120°C. Frequency of the oscillations was fixed at 1 Hz and the strain amplitude was 0.1%, which was well within the linear viscoelastic region. The heating rate was 2°C/min for all temperature scan tests. Storage modulus (E′), loss modulus (E″), and mechanical loss factor (tan δ) were collected during the test and were plotted versus temperature. An increase in storage and loss moduli and a decrease in the mechanical loss factor were observed for all composites indicating more elastic behavior of the composites as compared with the pure PP. Changes in phase transition temperatures were monitored and possible causes were discussed. Results indicated that glass transition was slightly shifted to lower temperatures in composites. α transition temperature was higher in the case of composites and its intensity was higher as well. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4341–4349, 2006