钢渣颗粒对水中Cr(VI)的吸附与还原作用

以钢渣颗粒为水处理剂,分析了其组成和结构,研究了钢渣颗粒直接吸附去除水中Cr(VI)的工艺过程及机理. 结果表明,钢渣颗粒在适当的粒度与用量下,经10 min搅拌处理,水中Cr(VI)浓度由200 mg/L降低到0.5 mg/L,达到《污水综合排放标准》(GB8978-1996)的要求. 钢渣颗粒对水中Cr(VI)的吸附符合Langmuir等温吸附过程,对Cr(VI)的饱和吸附量达6.878 mg/g. 化学分析和XPS分析均表明,钢渣颗粒对水中Cr(VI)具有吸附与还原的联合作用,吸附后钢渣颗粒中Cr(III)含量由0.0985%提高到0.39%,而FeO含量由9.20%下降到8.35%. 吸附后钢渣颗粒表面形成了Cr(OH)3,说明钢渣颗粒中FeO充当了还原剂,将水中Cr(VI)吸附于钢渣颗粒表面并还原成了低毒的Cr(OH)3随钢渣颗粒沉降直接从水中去除.     

Adsorption of Cr (VI) Oxyanions onto Modified Wood Pulp

A new adsorbent was prepared from wood pulp (WP) after reaction with epichlorohydrin and dimethylamine in the presence of pyridine and N,N-dimethylformamide (DMF). The adsorption of Cr (VI) from aqueous solutions by the so-prepared wood pulp adsorbent (WP-A) was investigated. Various factors affecting adsorption, such as pH, adsorbent concentration (1–5 g/L), agitation time (5–60 min), and Cr (VI) concentration (50–700), were taken into consideration. The adsorption of Cr (VI) onto (WP-A) was found to be pH-dependent and maximum adsorption was obtained at pH 3. The adsorption data obeyed Langmuir and Freundlich adsorption isotherms. The Langmuir adsorption capacity (Q_max) was found to be 588.24 mg/g. Freundlich constants, K_F and n, were found to be 55.03 and 2.835, respectively.     

A Study in the Adsorption Behaviors of Cr (VI) on Crosslinked Cationic Starches

The adsorption behaviors between Cr (VI) and crosslinked cationic starch with quaternary ammonium group were investigated in various conditions. The adsorption processes are found to be dependent on the initial pH of the solution, the dose of the absorbents, initial concentration of Cr (VI), and adsorption temperature. The adsorption reaches equilibrium in a short time, and follows the Langmuir isotherm. The adsorption capacity increases with the increasing cationic groups. The adsorption thermodynamics study shows that adsorption processes are exothermic, and lower temperature is favorable to the adsorption of Cr (VI).     

分光光度法研究Cr(VI)氧化苹果酸及乙二醇的催化反应动力学

文章采用分光光度法研究了酸性介质中,2,2’-联吡啶(bpy)催化Cr(VI)氧化苹果酸(Mal)及乙二醇的反应动力学,分别考察了两种[R]、[H+]、[bpy]]对kobs的影响。结果表明:反应对Cr(VI)是准一级,对苹果酸及乙二醇均是一级。在保持准一级反应条件([还原剂]0[Cr(VI)0)下,该反应的表观速率常数kobs都随[H+]、[bpy]的增加而增大。通过比较Cr(VI)氧化苹果酸及二元醇的反应,发现同一温度下乙二醇的速率常数大于苹果酸的速率常数。     

Adsorption of Cr(VI) ions onto poly(ethylene glycol dimethacrylate‐1‐vinyl‐1,2,4‐triazole)

Poly(ethylene glycol dimethacrylate‐1‐vinyl‐1,2,4‐triazole) [poly(EGDMA‐VTAZ)] beads (average diameter = 150–200 μm) were prepared by copolymerizing ethylene glycol dimethacrylate (EGDMA) with 1‐vinyl‐1,2,4‐triazole (VTAZ). Poly(EGDMA‐VTAZ) beads were characterized by swelling studies and scanning electron microscope (SEM). The adsorption of Cr(VI) from solutions was carried at different contact times, Cr(VI) concentrations, pH, and temperatures. High adsorption rates were achieved in about 240 min. The amount of Cr(VI) adsorbed increased with increasing concentration and decreasing pH and temperature. The intraparticle diffusion rate constants at various temperatures were calculated. Adsorption isotherms of Cr(VI) onto poly(EGDMA‐VTAZ) have been determined and correlated with common isotherm equations such as Langmuir and Freundlich isotherm models. The Langmuir isotherm model appeared to fit the isotherm data better than the Freundlich isotherm model. The pseudo first‐order kinetic model was used to describe the kinetic data. The study of temperature effect was quantified by calculating various thermodynamic parameters such as Gibbs free energy, enthalpy, and entropy changes. The dimensionless separation factor (R_L) showed that the adsorption of metal ions onto poly(EGDMA‐VTAZ) was favorable. It was seen that values of distribution coefficient (K_D) decreasing with Cr(VI) concentration in solution at equilibrium (C_e) indicated that the occupation of activate surface sites of adsorbent increased with Cr(VI). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Studies of adsorption behavior of crosslinked chitosan for Cr(VI), Se(VI)

In this work, it was found that crosslinked chitosan (CCTS) had strong adsorption ability for some anions under certain conditions. Cr(VI) and Se(VI) existed in anion forms in aqueous solution, and their adsorption rates by CCTS were 97% for Cr(VI) at pH 3.0 and 95% for Se(VI) at pH 4.0. In addition, the adsorption balance time and isotherm of CCTS for Cr(VI) and Se (VI) were discussed and adsorption mechanism was explained. This research will be useful for designing CCTS‐based adsorption for metallic toxin removal and preconcentrating Cr(VI) and Se(VI) in their trace analysis. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 3216–3219, 2000     

Cysteine-Functionalized Chitosan Magnetic Nano-Based Particles for the Recovery of Uranium(VI): Uptake Kinetics and Sorption Isotherms

Magnetic-chitosan nanoparticles, functionalized with cysteine, were synthesized and characterized by element analysis, FT-IR, XRD, TEM, and vibrating sample magnetometry. The sorbent was tested for U(VI) recovery, considering:

• a. pH effect,

• b. sorption isotherms (fitted by Langmuir equation), and

• c. uptake kinetics (modeled using the PSORE).

Maximum sorption capacity approached 100 mg U g^?1. The nanometric size of sorbent reduces the impact of resistance to intraparticle diffusion; this may explain the fast kinetics (equilibrium within 50 min). The reaction is exothermic, spontaneous. The metal could be desorbed using acidified urea solution and the sorbent could be recycled for 5 cycles.     

铜渣基化学键合陶瓷材料吸附Cr(VI)的性能及机理

以富含铁的铜渣（CS）为原料,在碱激发条件下制备了铜渣基化学键合陶瓷材料（CSCBC）,对废水中的Cr(Ⅵ)进行吸附处理。考察了吸附剂添加量、Cr(Ⅵ)初始浓度及pH等因素对Cr(Ⅵ)吸附效果的影响,并通过吸附动力学和热力学分析,结合吸附前后吸附材料结构表征,对其吸附机理进行了探讨。结果表明,当Cr(Ⅵ)初始质量浓度为200 mg/L、pH=1、吸附剂投加量为0.4 g时,在240 min内达吸附平衡,Cr(Ⅵ)去除率可达93%以上,最大理论吸附容量25.3 mg/g。与生物炭基铁氧化物复合材料、FeS复合材料、铁掺杂吸附剂等同类型吸附剂相比,Cr(Ⅵ)吸附容量明显提高。CSCBC对Cr(Ⅵ)的吸附过程符合准一级动力学模型和Langmuir等温吸附模型。其吸附机制主要是还原、吸附等双重作用的结果。 6次吸附-解吸实验后,其吸附容量保持初次吸附容量的75%以上 。     

铜渣基化学键合陶瓷材料吸附Cr(VI)的性能及机理

以富含铁的铜渣（CS）为原料，在碱激发条件下制备了铜渣基化学键合陶瓷材料（CSCBC），对废水中的Cr(Ⅵ)进行吸附处理。考察了吸附剂添加量、Cr(Ⅵ)初始浓度及pH等因素对Cr(Ⅵ)吸附效果的影响，并通过吸附动力学和热力学分析，结合吸附前后吸附材料结构表征，对其吸附机理进行了探讨。结果表明，当Cr(Ⅵ)初始质量浓度为200 mg/L、pH=1、吸附剂投加量为0.4 g时，在240 min内达吸附平衡，Cr(Ⅵ)去除率可达93%以上，最大理论吸附容量25.3 mg/g。与生物炭基铁氧化物复合材料、FeS复合材料、铁掺杂吸附剂等同类型吸附剂相比，Cr(Ⅵ)吸附容量明显提高。CSCBC对Cr(Ⅵ)的吸附过程符合准一级动力学模型和Langmuir等温吸附模型。其吸附机制主要是还原、吸附等双重作用的结果。 6次吸附-解吸实验后，其吸附容量保持初次吸附容量的75%以上 。     

Adsorption of Cu(II) and Cr(VI) onto Treated Shorea dasyphylla Bark: Isotherm,Kinetics, and Thermodynamic Studies

The efficacy of treated Shorea dasyphylla bark for Cu(II) and Cr(VI) adsorption was assessed in a batch adsorption system as a function of pH, agitation period, and initial metal concentration. The equilibrium nature of Cu(II) and Cr(VI) adsorption was described by the Freundlich, Langmuir, and Dubinin-Radushkevich isotherms. The maximum monolayer capacities of treated Shorea dasyphylla bark, estimated from the Langmuir equation were 184.66 and 42.72 mg/g for Cu(II) and Cr(VI), respectively. The experimental results were fitted using pseudo-first order, pseudo-second order and intraparticle diffusion kinetic models; the pseudo-second order showed the best conformity to the kinetic data. Thermodynamic parameters such as enthalpy change (ΔH°), free energy change (ΔG°) and entropy change (ΔS°) were determined by applying the Van't Hoff equation. The adsorption of Cu(II) and Cr(VI) onto treated Shorea dasyphylla bark was found to be spontaneous and exothermic. The adsorption mechanism was confirmed by means of Fourier transform infrared (FTIR) and Energy dispersive X-ray (EDX) spectroscopy. The dimensionless constant separation factor (R _L), indicated that treated Shorea dasyphylla bark was favorable for Cu(II) and Cr(VI) adsorption.     

Studies on the removal of Cr(VI) from waste-water by feldspar

The efficacy of feldspar in the removal of Cr(VI) from representative waste-water from a plating industry has been investigated in a completely mixed batch reactor at different concentrations, rate of agitation and particle size. The data obey the Langmuir isotherm for the present system and the process of uptake follows first-order kinetics. The maximum removal (91%) was observed at 40°C and pH 2.5 with initial concentration of 19.23 μmol dm^?3 Cr(VI) and 40 g dm^?3 feldspar. The process involves both film and pore diffusion to different extents. Column studies have also been carried out using a certain concentration of waste-water. More than 92% recovery has been achieved and the column can be used for 10 cycles before regeneration. The present technique seems to be quite attractive.     

铝污泥基复合凝胶球对Cr(VI)的吸附性能与机理

以铝污泥、聚乙烯醇、海藻酸钠为原料,采用溶胶-凝胶、冷冻干燥技术制备铝污泥基复合凝胶球 (AS-GEL),吸附溶液中Cr(VI)。通过静态吸附实验探究pH、AS-GEL投加量、初始质量浓度、温度、吸附时间、共存阴离子浓度对AS-GEL吸附Cr(VI)的影响。采用 SEM、FT-IR、XPS等技术对AS-GEL吸附Cr(VI) 的机理进行分析。结果表明：在pH=4、AS-GEL投加量为1.2 g/L、Cr(VI)初始浓度200 mg/L、温度为35℃、吸附时间为120 min、无其他阴离子共存的条件下,AS-GEL对Cr(VI)的最大吸附量为73.364 mg/g。共存阴离子影响顺序为PO43- >NO3->Cl-。吸附过程符合Langmuir等温吸附模型和准一级、二级动力学方程。其主要吸附机理包括质子化基团对Cr(VI)的静电吸附及还原作用。通过5次吸附-解吸实验,其吸附量保持初次吸附量的89.71%。同时,AS-GEL具有成本低、固液易分离的特性,有望应用在工程上。     

Removal of Cr(VI) From Aqueous Solution by Turkish Vermiculite: Equilibrium,Thermodynamic and Kinetic Studies

Abstract

The adsorption of Cr(VI) from aqueous solution by Turkish vermiculite were investigated in terms of equilibrium, kinetics, and thermodynamics. Experimental parameters affecting the removal process such as pH of solution, adsorbent dosage, contact time, and temperature were studied. Equilibrium adsorption data were evaluated by Langmuir, Freundlich and Dubinin–Radushkevich (D–R) isotherm models. Langmuir model fitted the equilibrium data better than the Freundlich model. The monolayer adsorption capacity of Turkish vermiculite for Cr(VI) was found to be 87.7 mg/g at pH 1.5, 10 g/L adsorbent dosage and 20°C. The mean free energy of adsorption (5.9 kJ/mol) obtained from the D–R isotherm indicated that the type of sorption was essentially physical. The calculated thermodynamic parameters (ΔG ^o , ΔH ^o and ΔS ^o ) showed that the removal of Cr(VI) ions from aqueous solution by the vermiculite was feasible, spontaneous and exothermic at 20–50°C. Equilibrium data were also tested using the adsorption kinetic models and the results showed that the adsorption processes of Cr(VI) onto Turkish vermiculite followed well pseudo-second order kinetics.     

Efficient removal of Cr(VI) and Pb(II) from aqueous solution by magnetic nitrogen-doped carbon

The magnetic nitrogen-doped carbon (MNC) was prepared from polypyrrole by a simple high temperature calcination process in this paper. The structure and properties of MNC were analyzed by scanning electron microscope, Fourier transform infrared spectroscopy, X-ray diffraction, Brunner-Emmet-Teller, vibrating sample magnetometer, and X-ray photoelectron spectroscopy. The capacity of MNC to adsorb Cr(VI) and Pb(II) was evaluated. The effects of the initial pH, dosage, concentration and temperature on the adsorption capacity of MNC were measured. MNC had a large specific surface area and a special porous structure. Its nitrogen and carbon sources were rich, and the ratio of carbon to nitrogen was fixed. The maximum Cr(VI)-adsorption capacity and maximum Pb(II) adsorption capacity of MNC could reach 456.63 and 507.13 mg∙g⁻¹ at 318 K, respectively. The pseudo-second-order model was used to describe the adsorption kinetics of MNC, and the Freundlich model was employed to discuss its isotherms. The adsorption process was affected by the electrostatic force, the reducing reaction, pores and chelation. The results of this study suggest that MNC is a material with superior performance, and is very easily regenerated, reused, and separated in the adsorption process.     

Adsorption thermodynamics and kinetics of Cr(VI) on KIP210 resin

Series of resin selection experiments were carried out and the KIP210 strong base anion exchange resin was confirmed to have the maximum equilibrium adsorption capacity to remove Cr(VI) from wastewater. The adsorption thermodynamics and kinetics of Cr(VI) on KIP210 resin were investigated completely and systematically. The static experiments were performed to study the effects of various parameters, such as shaking speed, resin dosage and pH during the adsorption process. The results indicate that the effect of external diffusion is eliminated at 160 rpm, the best pH value is 3.0 and the removal percentage of Cr(VI) increases with the increase of the resin dosage. The adsorption of Cr(VI) on KIP210 agrees well with the Langmuir isotherm and the adsorption parameters of thermodynamics are ΔH = 26.5 kJ mol⁻¹, ΔS = 126.7 J mol⁻¹ K⁻¹ and ΔG < 0. It demonstrates that the adsorption of Cr(VI) on KIP210 is a spontaneously endothermic physisorption process. Moreover, the adsorption process can be described well by a pseudo-second-order kinetic model and the activation energy is 30.9 kJ mol⁻¹. The kinetic analysis showed that the adsorption rate is controlled by intraparticle diffusion. The resin is successfully regenerated using the NaOH solutions.     

Synthesis of S-rich flower-like Fe2O3-MoS2 for Cr(VI) removal

A novel Fe₂O₃-MoS₂ nanocomposite was synthesized directly via the solvothermal method. Scanning electron microscopy (SEM) results showed the as-prepared Fe₂O₃-MoS₂ had a uniform 3D blooming flower-like nanostructure with a MoS₂ substrate. The high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM) confirmed the Fe₂O₃ nanostructures were well-dispersed on the surface of the layered MoS₂. The elemental mapping results revealed Fe, O, Mo and S elements coexisted in the Fe₂O₃-MoS₂ nanocomposite. X-ray photoelectron spectroscopy (XPS) results displayed an S-rich MoS₂ structure had been formed in the Fe₂O₃-MoS₂ nanocomposite. As expected, the S-rich Fe₂O₃-MoS₂ nanocomposite had better photocatalytic performance on Cr(VI) reduction than that of bare Fe₂O₃, MoS₂ and TiO₂ P25.     

乙醇辅助氨基改性NCR-MCM-48分子筛的制备及其对Cr(VI)的吸附性能

以稻壳灰提纯出的硅胶为无机组装硅源,乙醇为辅助试剂,通过水热合成法制备了CR-MCM-48分子筛,并对其氨基改性接枝制备NCR-MCM-48介孔分子筛。实验探讨了硅钠比、晶化温度、晶化时间及乙醇含量对CR-MCM-48介孔结构和形貌的影响。通过X射线粉末衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、N₂吸附-脱附曲线和红外光谱(FT-IR)对合成材料进行了结构和形貌表征,并对NCR-MCM-48介孔材料吸附水溶液中Cr(VI)的性能进行了评价。结果表明,当物料摩尔比n(Si)∶n(CTAB)∶n(H₂O)∶n(NaOH)∶n(C₂H₅OH)=1.0∶0.65∶62∶0.625∶0.25,晶化温度为393 K,晶化时间为72 h,焙烧温度为823 K时,组装合成的CR-MCM-48介孔材料有序度最好。热力学分析结果表明,NCR-MCM-48对Cr(VI)的吸附是自发、吸热反应。在吸附温度为308 K、pH=2.0、吸附时间为150 min的条件下,NCR-MCM-48吸附剂对Cr(VI)的最大吸附容量为88.9 mg·g^-1。     

单宁基酚胺型螯合树脂的制备及对Cr(VI)的吸附

杨梅单宁先与氯化亚砜反应制得氯代单宁,再与聚乙烯亚胺交联合成单宁基酚胺型螯合树脂。通过FTIR、SEM、EDS和XPS对单宁基酚胺型螯合树脂的结构进行表征,并考察了螯合树脂对Cr(VI)的吸附性能。在单宁的分子结构侧链引入氨基,能有效改善单宁基螯合树脂对Cr(VI)的吸附性能,螯合树脂对Cr(VI)的吸附主要为还原吸附,铬主要以Cr(III)的形式吸附到树脂上;在温度为318 K、pH为2.0、Cr(VI)初始质量浓度为500 mg/L时,单宁基酚胺型螯合树脂对Cr(VI)的最大吸附量达到364.46 mg/g;当Cr(VI)初始质量浓度低于20 mg/L时,树脂对铬的吸附率达到95%以上;单宁基酚胺型螯合树脂对Cr(VI)的吸附过程符合Langmuir等温吸附模型和准二级吸附动力学方程。该树脂在含铬废水处理方面具有潜在的应用前景。     

Biosorption of Cr(VI) from aqueous solution using agricultural wastes,with artificial intelligence approach

Removal of Cr(VI) from aqueous solution by date-palm-leaves (DPL) and broad-bean-shoots (BBS) was investigated. FTIR, SEM, and EDAX showed that DPL has higher ability for ion-exchange to remove Cr(VI). Langmuir and Freundlich adsorption isotherms and kinetics revealed that DPL exhibited higher biosorption capacity. At Cr(VI) 100 mg/L, biosorbent-dose 5 g/L and 60 min contact-time, maximum Cr(VI) removal for DPL (98%) and BBS (95%) was achieved at pH 2 and 1, respectively. Adaptive-neuro fuzzy inference system determined the most important factor affecting Cr(VI) removal. The model indicated that DPL is more tolerant to pH levels, while BBS is a pH-sensitive adsorbent.     

Removal and Recovery of Chromium(VI) from Industrial Waste Water

Carbon slurry, generated as a waste material in a naphtha-based ammonia plant of the Fertilizer Corporation of India, Gorakhpur, has been used as an adsorbent for the removal of Cr(VI) from aqueous solution at different experimental conditions. The removal was favoured at low pH, with maximum removal at pH 2·5. The effects of concentration and temperature have also been reported. Batch adsorption kinetics have been described by the Lagergren equation. The applicability of the Langmuir isotherm for the present system has been tested at different temperatures. Thermodynamic parameters indicate the endothermic nature of Cr(VI) adsorption on carbon slurry. Recovery of adsorbed chromium for reuse has also been reported in the present study. © 1997 SCI.