Performance enhancement of multicrystalline silicon solar cells and modules using double‐layered SiNx:H antireflection coatings

Silicon nitride coating deposited by the plasma‐enhanced chemical vapor deposition method is the most widely used antireflection coating for crystalline silicon solar cells. In this work, we employed double‐layered silicon nitride coating consisting of a top layer with a lower refractive index and a bottom layer (contacting the silicon wafer) with a higher refractive index for multicrystalline silicon solar cells. An optimization procedure was presented for maximizing the photovoltaic performance of the encapsulated solar cells or modules. The dependence of their photovoltaic properties on the thickness of silicon nitride coatings was carefully analyzed. Desirable thicknesses of the individual silicon nitride layers for the double‐layered coatings were calculated. In order to get statistical conclusions, we fabricated a large number of multicrystalline silicon solar cells using the standard production line for both the double‐layered and single‐layered antireflection coating types. On the cell level, the double‐layered silicon nitride antireflection coating resulted in an increase of 0.21%, absolute for the average conversion efficiency, and 1.8 mV and 0.11 mA/cm² for the average open‐circuit voltage and short‐circuit current density, respectively. On the module level, the cell to module power transfer factor was analyzed, and it was demonstrated that the double‐layered silicon nitride antireflection coating provided a consistent enhancement in the photovoltaic performance for multicrystalline silicon solar cell modules than the single‐layered silicon nitride coating. Copyright © 2015 John Wiley & Sons, Ltd.     

Multi‐crystalline Si solar cells with very fast deposited (180 nm/min) passivating hot‐wire CVD silicon nitride as antireflection coating

Hot‐wire chemical vapor deposition (HWCVD) is a promising technique for very fast deposition of high quality thin films. We developed processing conditions for device‐ quality silicon nitride (a‐SiN_x:H) anti‐reflection coating (ARC) at high deposition rates of 3 nm/s. The HWCVD SiN_x layers were deposited on multicrystalline silicon (mc‐Si) solar cells provided by IMEC and ECN Solar Energy. Reference cells were provided with optimized parallel plate PECVD SiN_x and microwave PECVD SiN_x respectively. The application of HWCVD SiN_x on IMEC mc‐Si solar cells led to effective passivation, evidenced by a V_oc of 606 mV and consistent IQE curves. For further optimization, series were made with HW SiN_x (with different x) on mc‐Si solar cells from ECN Solar Energy. The best cell efficiencies were obtained for samples with a N/Si ratio of 1·2 and a high mass density of >2·9 g/cm³. The best solar cells reached an efficiency of 15·7%, which is similar to the best reference cell, made from neighboring wafers, with microwave PECVD SiN_x. The IQE measurements and high V_oc values for these cells with HW SiN_x demonstrate good bulk passivation. PC1D simulations confirm the excellent bulk‐ and surface‐passivation for HW SiN_x coatings. Interesting is the significantly higher blue response for the cells with HWCVD SiN_x when compared to the PECVD SiN_x reference cells. This difference in blue response is caused by lower light absorption of the HWCVD layers (compared to microwave CVD; ECN) and better surface passivation (compared to parallel plate PECVD; IMEC). The application of HW SiN_x as a passivating antireflection layer on mc‐Si solar cells leads to efficiencies comparable to those with optimized PECVD SiN_x coatings, although HWCVD is performed at a much higher deposition rate. Copyright © 2007 John Wiley & Sons, Ltd.     

Optimization of Al_2O_3/SiN_x stacked antireflection structures for N-type surface-passivated crystalline silicon solar cells

In the case of N-type solar cells,the anti-reflection property,as one of the important factors to further improve the energy-conversion efficiency,has been optimized using a stacked Al₂O₃/SiN_x layer.The effect of SiN_x layer thickness on the surface reflection property was systematically studied in terms of both experimental and theoretical measurement.In the stacked Al₂O₃/SiN_x layers,results demonstrated that the surface reflection property can be effectively optimized by adding a SiN_x layer,leading to the improvement in the final photovoltaic characteristic of the N-type solar cells.     

N型表面钝化晶体硅太阳电池Al2O3/SiNx减反射叠层的优化研究

减反射特性是进一步提高N型太阳电池能量转换效率的重要因素之一。研究采用Al2O3/SiNx叠层优化了N型太阳电池的减反射特性,并通过理论模拟和实验测量系统地探讨了叠层中SiNx厚度对表面反射性能的影响。研究证实在Al2O3层上增加一层SiNx,可以有效地优化表面减反射性质,从而提高N型太阳电池的光伏性质。     

物理冶金多晶硅太阳电池叠层钝化减反射结构模拟

采用PC1D模拟软件对p型物理冶金多晶硅太阳电池的SiO2/Si Nx/SiNx叠层钝化减反射结构进行了计算模拟。结果表明:在SiNx/Si Nx双层减反射结构中引入SiO2钝化层后可以明显改善电池的外量子效率与表面减反射效果,并最终提高电池转换效率;随着SiO2膜厚度的增加,电池表面反射率呈先降低后增加的趋势,而电池外量子效率及转换效率则呈现出相反的趋势。二氧化硅膜厚度在2~8 nm时,电池转换效率变化不大,并在6 nm时效率达到最大值18.04%,当二氧化硅膜厚度大于8 nm后电池转换效率会出现明显下降。     

Comparison of TiO2 and other dielectric coatings for buried‐contact solar cells: a review

This paper compares the optical, electronic, physical and chemical properties of dielectric thin films that are commonly used to enhance the performance of bulk silicon photovoltaic devices. The standard buried‐contact (BC) solar cell presents a particularly challenging set of criteria, requiring the dielectric film to act as: (i) an anti‐reflection (AR) coating; (ii) a film compatible with surface passivation; (iii) a mask for an electroless metal plating step; (iv) a diffusion barrier for achieving a selective emitter; (v) a film with excellent chemical resistance; (vi) a stable layer during high‐temperature processing. The dielectric coatings reviewed here include thermally grown silicon dioxide (SiO₂), silicon nitride deposited by plasma‐enhanced chemical vapour deposition (a‐ SiN_x :H) and low‐pressure chemical vapour deposition (Si₃N₄), silicon oxynitride (SiON), cerium dioxide (CeO₂), zinc sulphide (ZnS), and titanium dioxide (TiO₂). While TiO₂ dielectric coatings exhibit the best optical performance and a simple post‐deposition surface passivation sequence has been developed, they require an additional sacrificial diffusion barrier to survive the heavy groove diffusion step. A‐ SiN_x :H affords passivation through its high fixed positive charge density and large hydrogen concentration; however, it is difficult to retain these electronic benefits during lengthy high‐temperature processing. Therefore, for the BC solar cell, Si₃N₄ films would appear to be the best choice of dielectric films common in industrial use. Copyright © 2004 John Wiley & Sons, Ltd.     

Silicon nitride processing for control of optical and electronic properties of silicon solar cells

Thin films of SiN are well suited as antireflection (AR) coatings for Si solar cells because their optical properties, such as refractive index and absorption coefficient, can be tailored during deposition to match those of Si solar cells. The SiN layers, particularly those deposited by a plasma-enhanced chemical vapor deposition (PECVD) process, can serve other functions in Si solar-cell fabrication. They can be excellent buffer layers through which the front metal contact can be fired. The PECVD nitridation also introduces H into the Si surface, which diffuses deep into the solar cell and passivates residual impurities and defects during metal-contact firing. The optimization of SiN properties and processing conditions may have conflicting demands based on its multifunctional role. To fully exploit these multiple functions, the SiN processing sequence must be optimized based on the properties of the nitride, the diffusion behavior of H, and the interactions of metal with the SiN/Si composite substrate.     

Combined effect of light harvesting strings,anti‐reflective coating,thin glass,and high ultraviolet transmission encapsulant to reduce optical losses in solar modules

Optical losses are a major source for current and power reduction in solar modules. Hence, various improvements aiming at reducing these losses have been suggested. In this work, we have evaluated the effects of anti‐reflective coating, front glass thickness, polyvinyl butyral ultraviolet+ encapsulant, and light harvesting strings on the module performance individually and in combination. The individual and combined contributions were quantified by spectrally resolved optical measurements on the module components and simulations as well as electrical measurements on 1‐cell and 54‐cell modules. Optical gains and their impact on short circuit current are discussed in relation to a maximum current obtained from the solar cells internal quantum efficiency. The results of the electrical characterization are in good agreement with the optical analysis substantiating our approach. They show that a combined, relative current enhancement of 5% can be obtained for an optimized module, which compares to an increase of 1% absolute efficiency. Copyright © 2014 John Wiley & Sons, Ltd.     

Simulation and fabrication of heterojunction silicon solar cells from numerical computer and hot‐wire CVD

In this paper, we will present a Pc1D numerical simulation for heterojunction (HJ) silicon solar cells, and discuss their possibilities and limitations. By means of modeling and numerical computer simulation, the influence of emitter‐layer/intrinsic‐layer/crystalline‐Si heterostructures with different thickness and crystallinity on the solar cell performance is investigated and compared with hot wire chemical vapor deposition (HWCVD) experimental results. A new technique for characterization of n‐type microcrystalline silicon (n‐µc‐Si)/intrinsic amorphous silicon (i‐a‐Si)/crystalline silicon (c‐Si) heterojunction solar cells from Pc1D is developed. Results of numerical modeling as well as experimental data obtained using HWCVD on µc‐Si (n)/a‐Si (i)/c‐Si (p) heterojunction are presented. This work improves the understanding of HJ solar cells to derive arguments for design optimization. Some simulated parameters of solar cells were obtained: the best results for J_sc = 39·4 mA/cm², V_oc = 0·64 V, FF = 83%, and η = 21% have been achieved. After optimizing the deposition parameters of the n‐layer and the H₂ pretreatment of solar cell, the single‐side HJ solar cells with J_sc = 34·6 mA/cm², V_oc = 0·615 V, FF = 71%, and an efficiency of 15·2% have been achieved. The double‐side HJ solar cell with J_sc = 34·8 mA/cm², V_oc = 0·645 V, FF = 73%, and an efficiency of 16·4% has been fabricated. Copyright © 2009 John Wiley & Sons, Ltd.     

Simulation and implementation of a porous silicon reflector for epitaxial silicon solar cells

One of the main challenges in the ongoing development of thin film crystalline silicon solar cells on a supporting silicon substrate is the implementation of a long‐wavelength reflector at the interface between the epitaxial layer and the substrate. IMEC has developed such a reflector based on electrochemical anodization of silicon to create a multi‐layer porous silicon stack with alternating high and low porosity layers. This innovation results in a 1–2% absolute increase in efficiency for screenprinted epitaxial cells with a record of 13·8%. To reach a better understanding of the reflector and to aid in its continued optimization, several extensive optical simulations have been performed using an in‐house‐developed optical software programme. This software is written as a Microsoft Excel workbook to make use of its user‐friendliness and modular structure. It can handle up to 15 individual dielectric layers and is used to determine the influence of the number and the sequence of the layers on the internal reflection. A sensitivity analysis is also presented. A study of the angle at which the light strikes the reflector shows separate regions in the physical working of the reflector which include a region where the Bragg effect is dominant as well as a region where total internal reflection plays the largest role. The existence of these regions is proved using reflection measurements. Based on these findings, an estimate is made for the achievable current gain with an ideal reflector and the potential of epitaxial silicon solar cells is determined. Copyright © 2008 John Wiley & Sons, Ltd.     

Study of base series resistance losses in single and double emitter silicon solar cells through simulations and experiments

This work focuses on base series resistance influence on the performance of single and double emitter rear point contact silicon solar cells. This study is performed through measurements on experimental devices with different rear contact sizes and spacings, which were designed and fabricated using standard silicon integrated circuit technology, while the results were compared with simulation data based on a 3D model developed at our institute. Simulation and experimental results show that the series resistance of the double junction structure is significantly lower compared to the single junction equivalent. In addition, it was demonstrated that the operation of both junctions under slightly different voltages improves device efficiency. Copyright © 2008 John Wiley & Sons, Ltd.     

Experimental and simulated analysis of front versus all‐back‐contact silicon heterojunction solar cells: effect of interface and doped a‐Si:H layer defects

Front silicon heterojunction and interdigitated all‐back‐contact silicon heterojunction (IBC‐SHJ) solar cells have the potential for high efficiency and low cost because of their good surface passivation, heterojunction contacts, and low temperature fabrication processes. The performance of both heterojunction device structures depends on the interface between the crystalline silicon (c‐Si) and intrinsic amorphous silicon [(i)a‐Si:H] layer, and the defects in doped a‐Si:H emitter or base contact layers. In this paper, effective minority carrier lifetimes of c‐Si using symmetric passivation structures were measured and analyzed using an extended Shockley–Read–Hall formalism to determine the input interface parameters needed for a successful 2D simulation of fabricated baseline solar cells. Subsequently, the performance of front silicon heterojunction and IBC‐SHJ devices was simulated to determine the influence of defects at the (i)a‐Si:H/c‐Si interface and in the doped a‐Si:H layers. For the baseline device parameters, the difference between the two device configurations is caused by the emitter/base contact gap recombination and the back surface geometry of IBC‐SHJ solar cell. This work provides a guide to the optimization of both types of SHJ device performance, predicting an IBC‐SHJ solar cell efficiency of 25% for realistic material parameters. Copyright © 2013 John Wiley & Sons, Ltd.     

Full‐wave optoelectrical modeling of optimized flattened light‐scattering substrate for high efficiency thin‐film silicon solar cells

The flattened light‐scattering substrate (FLiSS) is formed by a combination of two materials with a high refractive index mismatch, and it has a flat surface. A specific realization of this concept is a flattened two‐dimensional grating. When applied as a substrate for thin‐film silicon solar cells in the nip configuration, it is capable to reflect light with a high fraction of diffused component. Furthermore, the FLiSS is an ideal substrate for growing high‐quality microcrystalline silicon (µc‐Si:H), used as bottom cell absorber layer in most of multijunction solar cell architectures. FLiSS is a three‐dimensional structure; therefore, a full‐wave analysis of the electromagnetic field is necessary for its optimal implementation. Using finite element method, different shapes, materials, and geometrical parameters were investigated to obtain an optimized FLiSS. The application of the optimized FLiSS in µc‐Si:H single junction nip cell (1‐µm‐thick i‐layer) resulted in a 27.4‐mA/cm² implied photocurrent density. The absorptance of µc‐Si:H absorber exceeded the theoretical Yablonovitch limit for wavelengths larger than 750 nm. Double and triple junction nip solar cells on optimal FLiSS and with thin absorber layers were simulated. Results were in line with state‐of‐the‐art optical performance typical of solar cells with rough interfaces. After the optical optimization, a study of electrical performance was carried out by simulating current–voltage characteristics of nip solar cells on optimized FLiSS. Potential conversion efficiencies of 11.6%, 14.2%, and 16.0% for single, double, and triple junction solar cells with flat interfaces, respectively, were achieved. Copyright © 2012 John Wiley & Sons, Ltd.