Electrophoretic deposition of different carbon nanoscale reinforcements on carbon fiber fabrics and mechanical properties of the resulting hybrid multi‐scale epoxy composites

Three types of carbon nanoscale reinforcements (CNRs) including the shortened electrospun carbon nanofibers (ECNFs, with diameters and lengths of ∼200 nm and ∼15 µm, respectively), carbon nanofibers (CNFs), and graphite nanofibers (GNFs) were electrophoretically deposited on carbon fiber (CF) fabrics for the fabrication of hybrid multi‐scale epoxy composites. The results indicated that the electrophoretic deposition (EPD) of CNRs onto CF fabrics led to substantial improvements on mechanical properties of hybrid multi‐scale epoxy composites; in particular, the hybrid multi‐scale epoxy composite containing surface‐functionalized ECNFs (with amino groups) exhibited the highest mechanical properties. The study also indicated that some agglomerates of CNRs (particularly GNFs) could form during the EPD process, which would decrease mechanical properties of the resulting composites. Additionally, the reinforcement mechanisms were investigated, and the results suggested that continuous (or long) ECNFs would outperform short ECNFs on the reinforcement of resin‐rich interlaminar regions in the composites. POLYM. COMPOS., 35:1229–1237, 2014. © 2013 Society of Plastics Engineers     

Tailoring Carbon Fiber/Carbon Nanotubes Interface to Optimize Mechanical Properties of Cf‐CNTs/SiC Composites

C_f/SiC composites were fabricated using fiber coatings including CNTs and matrix infiltration using the polymer impregnation and pyrolysis process. Interface between fiber and CNTs (CF/CNTs) was tailored to optimize mechanical properties of hybrid composites. The tailored interphases, such as Pyrocarbon (PyC) and PyC/SiC, protect fibers from degradation during the growth of CNTs successfully. Hybrid composites with well‐tailored CF/CNTs interface displayed significantly increased mechanical strength (352 ± 21 MPa) compared with that (34 ± 3 MPa) of composites reinforced with CNTs, which grown on carbon fibers directly. The interfacial bonding strength of hybrid composites was improved and optimized by tailoring the CF/CNTs interface. Interfacial failure modes were studied, and a firm interface bonding at the joint where CNTs grown was observed.     

Hybrid clay‐carbon nanotube/PET composites: Preparation,processing, and analysis of physical properties

The aim of this work was the preparation of novel composites of poly(ethylene terephthalate) (PET) and nano‐hybrid systems based on clay used as catalyst for the growth of multi walled carbon nanotubes (Clay‐CNTs), through catalytic chemical vapor deposition (CCVD). The carbon content into the hybrid filler was 58.1 wt %. Composites with 1.0, 1.5, 2.0, 3.0 wt % of Clay–CNTs were obtained by melt compounding and processed using a microinjection molding press. Unfilled PET was processed in the same composites conditions. Structural characterization and physical properties (thermal, degradation, mechanical, and electrical) were analyzed and correlated to the hybrid filler loading, and carbon nanotubes amount. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40441.     

Incorporation of 4‐aminobenzene functionalized multi‐walled carbon nanotubes in polyaniline for application in formic acid electrooxidation

Incorporation of carbon nanotubes (CNTs) in conducting polymer can lead to new composites with enhanced electrical and mechanical properties. However, the development of such composites has been hampered by the inability to disperse CNTs in polymer matrix due to the lack of chemical compatibility between polymers and CNTs. Covalent sidewall functionalization of carbon nanotube provides a feasible route to incorporate carbon nanotube in polymer. In this work, 4‐aminobenzene groups were grafted onto the surface of multi‐walled carbon nanotube (MWNT) via C? C covalent bond. Polyaniline (PANI)/MWNT composites were fabricated by electrochemical polymerization of aniline containing well‐dissolved functionalized MWNTs. The obtained composites can be used as catalyst supports for electrooxidation of formic acid. Cyclic voltammogram results show that platinum particles deposited in PANI/MWNT composite films exhibit higher electrocatalytic activity and better long‐term stability towards formic acid oxidation than that deposited in pure PANI films. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and properties of hierarchical composites based on carbon nanotubes‐coated glass babric preform

A strategy based on carbon nanotubes (CNTs)‐containing sizing dispersion has been implemented to fabricate nanocomposite preforms and their hybrid multiscale composites. The state of pristine CNTs and carboxylic acid functionalized CNTs (CNTs–COOH) in sizing dispersion was effectively monitored by on‐line measuring electrical conductivity. The effects of different CNTs coating applied onto glass fabric on wettability of nanocomposite fibrous reinforcement with epoxy matrix were evaluated using scanning electron microscopy and capillary experiment. A CNTs‐COOH loading of 0.5 wt% gave rise to 97% and 30°C increases in the storage modulus (G′) and glass transition temperature of the resulting hybrid composites, respectively. The enhanced thermomechanical properties of the CNTs hybrid composites are closely related to the stable CNTs sizing dispersion and uniform coating onto fiber reinforcement. The mechanism for reinforcing composites through toughening resin region with CNTs desorbing from primary fiber surface during impregnation has been identified. POLYM. COMPOS. 37:979–986, 2016. © 2014 Society of Plastics Engineers     

Fluoroelastomer‐MWNT nanocomposites‐1: Dispersion,morphology, physico‐mechanical,and thermal properties

The present article reports the preparation and characterization of fluoroelastomer/multi‐walled nanotube hybrid nanocomposites prepared by conventional rubber mixing using a two‐roll mill. The morphology of the resulting hybrid nanocomposites were characterized by X‐ray diffraction (XRD), scanning (SEM) and transmission electron microscopies (TEM). SEM photographs showed the formation of completely exfoliated and uniformly dispersed nanotubes in the polymer matrix during the high shear mixing process. Magnetic force microscopy (MFM) has been used to further study the topography of the composites which also showed complete exfoliation. The effect of increasing MWNT loadings on the mechanical properties like tensile strength, modulus, elongation at break, hardness, and tear resistance has also been studied. The fracture surface of the composite has been studied by SEM. A “cross hatched pattern” has been observed. The thermal stability of the composites has been studied by TGA and increase in decomposition temperature with increase in MWNT loadings has been observed which was attributed to the antioxidant nature of nanotubes. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers.     

Molecular dynamics simulation of mechanical properties and interaction energy of polythiophene/polyethylene/poly(p‐phenylenevinylene) and CNTs composites

Carbon nanotubes (CNTs) have very important applications in ultrastrong lightweight materials. CNTs can improve mechanical properties of polymer matrix such as breaking stress and Young's modulus. In this article, we studied the interaction between polythiophene (PT)/polyethylene (PE)/poly(p‐phenylenevinylene) (PPV) and CNTs by molecular dynamics (MD) simulation based on a reactive force field (ReaxFF). We studied the influence of CNT diameter, polymer type, and temperature on interaction energy. We found that a large radius CNT at low temperature shows the strongest interaction energy with PT. In addition, we computed the mechanical properties of CNTs‐polymer composites such as the breaking stress, breaking strain, and Young's modulus. Our results show that there is a direct relation between mechanical properties and interaction energy. We found that the mechanical properties of CNTs‐PT composite are better than CNTs‐PPV and CNTs‐PE and it is a good candidate for ultrastrong lightweight materials. We studied the influence of temperature on the mechanical properties. Our results show that CNTs‐polymer composites show stronger mechanical properties at low temperature. We found that ReaxFF can reproduce the other force fields results and it is a very powerful force field to study the various properties of CNTs‐polymer composites. POLYM. COMPOS., 35:2261–2268, 2014. © 2014 Society of Plastics Engineers     

Structure and properties of aeronautical composites using carbon nanotubes/epoxy dispersion as nanocomposite matrix

The structure and properties of hybrid multiscale composites containing carbon nanotubes (CNTs) was reported. CNTs were dispersed in epoxy by using high energy ultrasonication, followed by the fabrication of CNT hybrid composites via resin transfer molding (RTM) processing. The processability of CNTs/epoxy systems was explored by a capillary experiment. The dependences of mechanical and electrical properties of the hybrid composites on CNT content were investigated. Microscopic observation confirms the formation of CNTs percolation network. The different roles of CNT networks in mechanical reinforcement and electrical amelioration were analyzed. One explanation based on the dispersion and distribution of CNTs is proposed. It is found that the variations of the hybrid composites with respect to mechanical and electrical properties are attributed to the hierarchical structure in the hybrid composites. As far as the hybrid multiscale composites produced via RTM process is concerned, the formation of CNT percolation network, subjected to dynamic impregnation, is hindered by the presence of continuous fibrous reinforcement. The hierarchical structure influenced by several competing factors reveals great potential in being able to tailor the structural and functional performance of the CNT hybrid composites. The effects of CNTs on the dimensional stability of polymer based composites are also assessed. POLYM. COMPOS., 34:1690–1697, 2013. © 2013 Society of Plastics Engineers     

Effects of orientation ordering of low‐density polyethylene—multi‐walled carbon nanotubes composites determined by severe plastic deformation

In this work, by the example of the system of linear low‐density polyethylene—multi‐walled carbon nanotubes (LLDPE/CNTs), specific features of the nanocomposite structure modified by severe plastic deformation (SPD) are studied. The effect of SPD on the mechanical properties and electrical conductivity is analyzed. It is shown that SPD leads to destruction of CNTs aggregates and more homogeneous their distribution. CNTs formed structure is characterized by the presence of large (200–300 nm) aggregates of CNTs and small (<100 nm) CNTs aggregates. It is found that within the range of a small degree of strain (up to e = 4.4), rupture is the prevailing mechanism of agglomerate disintegration, and erosion dominates in the range of high strain (e = 4.4–8.5). SPD‐induced formation of a 3D‐conducting network of CNT_S and strengthened LLDPE matrix determines an enhanced set of electrical and mechanical characteristics of the tested composites. POLYM. ENG. SCI., 59:714–723, 2019. © 2018 Society of Plastics Engineers     

Comparison of two different carbon nanotubes-based hybrid multiscale composites with respect to mechanical and electrical properties

Pristine and carboxylic acid functionalised carbon nanotubes (CNTs-P and CNTs-COOH) hybrid composites based on ultrasonically processed nanocomposite epoxy matrix have been prepared. The thermodynamic interactions between CNTs and epoxy components are evaluated through solution experiment. The measurements of mechanical properties and volume electrical resistivity are performed to characterise the structure-property interplay of CNTs hybrid composites. A 0.3?wt-% CNTs-COOH loading significantly enhances the glass transition temperatures (Tg) of the resultant hybrid composites. The re-agglomeration of CNTs-P has been ascribed to the thermodynamic and kinetic factors, which determine the morphological characteristics of CNTs within the overall composites. CNTs-P network enables a continuous conductive path to be present in the composites at lower CNTs-P concentration. An analysis of the effects of the functionalisation of CNTs on the structure and properties of their hybrid composites has been carried out.     

Bulk and nano‐mechanical behavior of silver and silver‐CNT‐reinforced hybrid polymer composites

The present study concerns study of the Bulk and nano‐mechanical properties of Ag‐CNT vis‐à‐vis Ag reinforced polymer composites. The Ag‐CNT hybrid powder blend was prepared by mechanical milling. Variation of the bulk and nano‐mechanical properties has been attributed to the morphological features and the degree of dispersion of the fillers. It has been found that dispersion of Ag‐CNT hybrid particle is beneficial for improvement of both the mechanical properties. POLYM. COMPOS., 37:2581–2587, 2016. © 2015 Society of Plastics Engineers     

Mechanical,thermal and electrical properties of multi‐walled carbon nanotube/aluminium nitride/polyetherimide nanocomposites

A series of polyimide‐based nanocomposites containing polyimide‐grafted multi‐walled carbon nanotubes (PI‐g MWCNTs) and silane‐modified ceramic (aluminium nitride (AlN)) were prepared. The mechanical, thermal and electrical properties of hybrid PI‐g MWCNT/AlN/polyetherimide nanocomposites were investigated. After polyimide grafting modification, the PI‐g MWCNTs showed good dispersion and wettability in the polyetherimide matrix and imparted excellent mechanical, electrical and thermal properties. The utilization of the hybrid filler was found to be effective in increasing the thermal conductivity of the composites due to the enhanced connectivity due to the high‐aspect‐ratio MWCNT filler. The use of spherical AlN filler and PI‐g MWCNT filler resulted in composite materials with enhanced thermal conductivity and low coefficient of thermal expansion. Results indicated that the hybrid PI‐g MWCNT and AlN fillers incorporated into the polyetherimide matrix enhanced significantly the thermal stability, thermal conductivity and mechanical properties of the matrix. Copyright © 2012 Society of Chemical Industry     

Efficient functionalization of multi‐walled carbon nanotubes with p‐aminophenol and their application in the fabrication of poly(amide‐imide)‐matrix composites

The ultrasonically assisted preparation and characterization of poly(amide‐imide) (PAI) composites containing functionalized multi‐walled carbon nanotubes (MWCNTs) are reported. To improve the dispersion in and compatibility with the polymer matrix, the MWCNTs were surface‐modified with p‐aminophenol (p‐AP) under microwave irradiation. The process is fast, one‐pot, easy and results in a high degree of functionalization as well as dispersibility in organic solvents. The p‐AP‐functionalized MWCNTs (MWCNTs‐AP) were analysed by means of field emission and transmission electron microscopy, Fourier transform infrared spectroscopy, X‐ray diffraction and thermogravimetric analysis (TGA). The results consistently confirm the formation of p‐AP functionalities on MWCNTs which are able to undergo additional reactions, while the structure of the MWCNTs remains relatively intact. MWCNTs‐AP/PAI hybrid films were prepared with various MWCNTs‐AP contents (5–15 wt%) using a solution‐casting technique. Microscopic observations show that the dispersion of the MWCNTs‐AP is improved as a result of the organic groups on the MWCNT surface and functional groups in the PAI structure. The properties of the obtained composites were characterized extensively using the aforementioned techniques. TGA results show that the hybrid films exhibit a good thermal stability. Tensile mechanical testing was performed for the prepared composites, the results of which indicate an increase in the elastic modulus and tensile strength with increasing MWCNTs‐AP content. © 2013 Society of Chemical Industry     

Effect of carbon nanotube purification on the electrical and mechanical properties of poly(ethylene terephthalate) composites with carbon nanotubes in low concentration

Surface properties of carbon nanotubes (CNTs) were altered by purification with nitric acid, sulfuric acid, ammonium hydroxide, and hydrogen peroxide. As‐received and purified CNT‐based conductive poly (ethylene terephthalate) composites were prepared with a twin‐screw extruder. The effects of CNT purification on the surface properties of the CNTs and on the morphology and electrical and mechanical properties of CNT‐based composites were investigated. Surface energy measurements showed that the acidic component of the surface energies of the CNTs increased after purification. According to Fourier transform infrared (FTIR) spectroscopy, the purification resulted in the formation of oxygen‐containing functional groups on the surfaces of the CNTs. Electron spectroscopy for chemical analysis results indicate the removal of the metallic catalyst residues and an increase in the oxygen content of the CNT surfaces as a result of the purification procedure. X‐ray diffraction analyses revealed a change in the crystalline structure of the CNTs after purification. All of the composites prepared with the purified CNTs had higher electrical resistivities and tensile and impact strength values than the composites based on the as‐received CNTs because of the functional groups and defect sites formed on the surfaces of the CNTs during purification. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

Polypropylene (PP) hybrid composites have been produced by compounding two types of mineral fillers, viz., talc and kaolin with PP copolymer using a twin screw extruder. The PP hybrid composite was injection‐molded into dumbbell specimen for tensile, flexural, and impact properties characterizations. MFI and SEM studies were used to characterize the flow and morphological properties of the PP hybrid composites. The result shows that most of the hybrid composites showed a significant decrease in flow, tensile, flexural, and impact properties compared with the single filler‐filled PP composites. However, a hybridization effect was seen for the PPT20K10 hybrid composites, through the synergistic coalescence of positive characteristics from 20 wt % of talc and 10 wt % of kaolin. This hybrid formulation have given an economically advantageous material with the mechanical properties (tensile, flexural, and impact) comparable to those of the talc‐filled PP composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 434–441, 2007     

Simultaneous ultrasonication‐assisted internal mixing to prepare MWCNTs‐filled epoxy composites with increased strength and thermal conductivity

The uniform dispersion of carbon nanotubes in epoxy resin is one of the key factors to achieve the composites with desirable mechanical and physical property enforcement. However, the widely used dispersion methods have their own respective limitations in pursuing satisfactory nanotube dispersion. Herein, a new dispersion approach, based on the synergetic effect of combining high speed internal mixing with running simultaneously continuous ultrasonication treatment, has been proposed. The dispersion of nanotubes was carried out in a high speed internal mixer, consisting of twin kneading block structured rotors and an integrated ultrasonic horn, which was intercalated into the central position between the twin rotors. At first, the FEM simulation was conducted to optimize the kneading element assembly and illuminate the geometry influence of the ultrasonic horn intercalation on the mixing flow. Afterwards, to confirm the feasibility of the approach, pristine MWCNTs (P‐CNTs), oxidation modified MWCNTs (M‐CNTs) and M‐CNTs/multilayer graphene nanoplatelets (MGPs) hybrid are dispersed into epoxy resin. The dispersion of each sample in its liquid epoxy state is investigated under transparent optical microscopy. More characterizations, including SEM, TG/DTA, tensile test, and thermal conductivity measurements, were conducted on the cured composites. Competitive reinforcements on mechanical tensile property and thermal conductivity were observed. Especially, at a 1.5 wt% M‐CNTs/MGPs hybrid content, the composite mechanical tensile strength and thermal conductivity were 47% and 30% higher than those of neat epoxy. This preliminary study demonstrates the feasibility and practicability of the proposed approach to achieving good MWCNTs dispersion and distribution in epoxy resin. POLYM. COMPOS., 37:870–880, 2016. © 2014 Society of Plastics Engineers     

Synthesis of hybrid ZnO/CNTs nanoparticles and their reinforcement in nylon‐6 polymer fibers

In this investigation, in situ synthesis of zinc oxide nanoparticles in the presence of multiwalled carbon nanotubes (CNTs) have been carried out using a sonochemical technique. Zinc(II)acetate was used as a source of ZnO in the presence of ethylene glycol (EG) to obtain zinc oxide (ZnO) nanoparticles. The synthesized hybrid ZnO/CNTs nanoparticles were used as reinforcements to enhance the mechanical, thermal and UV absorbing properties of Nylon‐6 composite fibers. The polymer nanocomposites (PNC) were fabricated by dry mixing Nylon‐6 polymer powder with the ZnO/CNTs hybrid nanoparticles as the first step, then followed by the drying and melt extrusion process of fiber materials in a single‐screw extruder. The extruded fibers were stretched and stabilized using a godet set‐up and wound on a Wayne filament winder machine. The hybrid ZnO/CNTs infused Nylon‐6 composite fibers were compared with commercial ZnO, CNTs infused Nylon‐6 composite fibers and neat Nylon‐6 fibers for their structural and thermal properties. The morphological characteristics of ZnO/CNTs nanoparticles were carried out using X‐ray diffraction and transmission electron microscopy (TEM) techniques. The Nylon‐6 PNC fibers which were of ～80 μ size were tested mechanically. The tensile tests revealed that failure stress of the 1% infused ZnO/CNTs Nylon‐6 PNC fibers is about 73% higher than the neat extruded Nylon‐6 fiber and the improvement in the tensile modulus is 377.4%. The DSC results show an increase in the glass transition temperature and crystallization for ZnO/CNTs infused Nylon‐6 PNC fibers. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Multiscale fiber‐reinforced composites prepared by vacuum‐assisted resin transfer molding

Carbon nanotube (CNT)/aramid fiber epoxy composites were produced using a new manufacturing method proposed in this study. The rheological and morphological experiments of the CNT/PEO nanocomposites indicates that the PEO nanocomposites have a good dispersion state of the CNTs. The flexural mechanical properties of the aramid fiber/CNT epoxy composites were measured. The CNTs dispersed in the epoxy resin between the aramid fibers were observed using field emission scanning electron miscroscope (FESEM). It was found that the flexural properties of the multiscale fiber‐reinforced composites were higher than those of aramid fiber/epoxy composites. POLYM. COMPOS., 28:458–461, 2007. © 2007 Society of Plastics Engineers.     

Recycled milk pouch and virgin LDPE‐LLDPE‐based jute fiber composites

The present investigation deals with the thermo‐mechanical recycling of post consumer milk pouches (LDPE‐LLDPE blend) and its use as jute fiber composite materials for engineering applications. The mechanical, thermal, morphological, and dynamic‐mechanical properties of recycled milk pouch‐based jute fiber composites with different fiber contents were evaluated and compared with those of the virgin LDPE‐LLDPE/jute fiber composites. Effect of artificial weathering on mechanical properties of different formulated composites was determined. The recycled polymer‐based jute fiber composites showed inferior mechanical properties as well as poor thermal stability compared to those observed for virgin polymer/jute fiber composites. However, the jute‐composites made with (50:50) recycled milk pouch‐virgin LDPE‐LLDPE blend as polymer matrix indicated significantly superior properties in comparison to the recycled milk pouch/jute composites. Overall mechanical performances of the recycled and virgin polymeric composites were correlated by scanning electron microscopy (SEM). The dynamic mechanical analysis showed that storage modulus values were lower for recycled LDPE‐LLDPE/jute composites compared to virgin LDPE‐LLDPE/jute composites throughout the entire temperature range, but an increase in the storage modulus was observed for recycled‐virgin LDPE‐LLDPE/jute composites. POLYM. COMPOS. 28:78–88, 2007. © 2007 Society of Plastics Engineers     

Electrical and mechanical properties of carbon nanotube‐epoxy nanocomposites

In this work, electrical conductivity and thermo‐mechanical properties have been measured for carbon nanotube reinforced epoxy matrix composites. These nanocomposites consisted of two types of nanofillers, single walled carbon nanotubes (SW‐CNT) and electrical grade carbon nanotubes (XD‐CNT). The influence of the type of nanotubes and their corresponding loading weight fraction on the microstructure and the resulting electrical and mechanical properties of the nanocomposites have been investigated. The electrical conductivity of the nanocomposites showed a significantly high, about seven orders of magnitude, improvement at very low loading weight fractions of nanotubes in both types of nanocomposites. The percolation threshold in nanocomposites with SW‐CNT fillers was found to be around 0.015 wt % and that with XD‐CNT fillers around 0.0225 wt %. Transmission optical microscopy of the nanocomposites revealed some differences in the microstructure of the two types of nanocomposites which can be related to the variation in the percolation thresholds of these nanocomposites. The mechanical properties (storage modulus and loss modulus) and the glass transition temperature have not been compromised with the addition of fillers compared with significant enhancement of electrical properties. The main significance of these results is that XD‐CNTs can be used as a cost effective nanofiller for electrical applications of epoxy based nanocomposites at a fraction of SW‐CNT cost. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010