Phase transitions and dimensional and morphological changes in an “Aluminum Hydroxide-Alumina” system under a shock-wave action

A method is proposed to study the sequence of phase transitions in powdered materials under a shock-wave action. It is shown that the aluminum hydroxide-alumina system has the following sequence of phase transformations under a shock-wave action: bayerite boehmite -Al₂O₃ -Al₂O₃. It is found that there are no transitional high-temperature modifications of alumina. A method is developed for obtaining a submicron alumina powder, which allows obtaining materials with a controlled phase composition, including a thermodynamically stable -modification of Al₂O₃. The specific features of the morphological structure and the phase and structural characteristics of powders after a shock-wave action are considered.Translated from Fizika Goreniya i Vzryva, Vol. 41, No. 1, pp. 110–119, January–February, 2005.     

Asymmetric structure analysis of active surface-sites by in situ polarized total-reflection fluorescence EXAFS

An in situ polarization-dependent total reflection fluorescence yield EXAFS system has been developed to analyze the asymmetric structures of catalytically active metal sites on single crystal surfaces. This technique separately reveals the bonding feature parallel and perpendicular to the support surface. The systems of Cu ion on -quartz(0001), Co oxide on -alumina(0001), and Pt₄ on -alumina(0001) were investigated as model surfaces of supported catalytic systems. The location of Cu sites on -quartz(0001), the epitaxial growth mode of Co₃O₄ on -alumina(0001), and the Pt raft structure with metal-support interaction in Pt₄ / -alumina(0001) were observed.     

Investigation of sex pheromone components of female asian corn borer,Ostrinia furnacalis (Hübner) (Lepidoptera: Pyralidae) in Taiwan

(E)-12-Tetradecenyl acetate (E12–14OAc), (Z)-12-tetradecenyl acetate (Z12–143nOAc), and tetradecanyl acetate (14OAc) were extracted and identified as major chemical components from female tips of the Asian corn borer,Ostrinia furnacalis (Hübner) (Lepidoptera: Pyralidae) in Taiwan, with a combined wash ratio of 483715 and an individual female ratio of 453916. The average amount ofE12-,Z12–14OAc and 14OAc in each female gland was 6.6±4.6, 5.8±3.5, and 2.4±1.7 ng/female, respectively. The mixture of these three synthetic chemicals not only gave strong activities in male antennae but also could catch significantly more males than virgin females in field-trapping tests. The field test also showed no significant difference in trapping ability among the three-component Taiwan formulations, the two-component Taiwan formulation (Z12–14OAc andZ1214OAc, 5347), and the Japan formulation (Z12–14 OAc andE 12–14OAc, 3:2).     

Factors governing the electrochemical synthesis of α-nickel (ii) hydroxide

The electrodeposition of -nickel hydroxide is promoted by the simultaneous chemical corrosion of the electrode by an acidic nitrate bath. Chemical corrosion results in the formation of a poorly ordered layered phase which is structurally similar to -nickel hydroxide and provides nucleation sites for the deposition of the latter. Therefore under conditions which enhance corrosion rates such as low current density (<1.3 mA cm–2), high temperature (60 C), high nickel nitrate concentration ( 1M) and the resultant low pH (1.7), -nickel hydroxide electrodeposition is observed, while -nickel hydroxide forms under other conditions. Further, -nickel hydroxide deposition is more facile on an iron electrode compared to nickel or platinum.     

Mechanisms of Iron Activation on Fe-Containing Zeolites and the Charge of α-Oxygen

According to previous Mössbauer data [1] -sites formation at the activation of Fe-containing zeolites is accompanied by irreversible self-reduction of the iron, proceeding without participation of an external reducing agent. Reduced Fe²⁺ ions are inert to O₂ but are reversibly oxidized to Fe³⁺ by N₂O, generating the -oxygen species, O, which provide selective oxidation of hydrocarbons.In this work, the mechanism of -sites formation was studied via quantitative measurement of the dioxygen amount desorbed into the gas phase at the step of self-reduction. A prominent role of the zeolite matrix chemical composition has been revealed. For example, with zeolites of Al–Si composition (FeZSM-5 and Fe-), heating to 900 °C in a closed vacuum space leads to irreversible evolution of O₂, which is accompanied by the immediate formation of -sites. Similar heating of B–Si and Ti–Si zeolites also leads to dioxygen evolution; however, this evolution is reversible and is not accompanied by formation of -sites. Activation of these zeolites occurs only in the presence of water vapor. Stoichiometric measurements showed that in terms of charge one regular O^2- ion, removed at the activation, is equivalent to two -oxygen atoms. So, -oxygen is identified as an ion-radical species O ^-., whose unique oxidation properties still distinguish it from the generally observed O^-. radicals.The mechanism of -sites formation is proposed, in which the process of strong chemical stabilization of reduced Fe²⁺ atoms in the zeolite structure is a key step, making impossible the reoxidation of the iron with O₂.     

Synthesis and properties of aromatic polyesters and brominated polyesters derived from α,α′-bis(4-hydroxyphenyl)-1,4(or 1,3)-diisopropylbenzene

The interfacial polycondensation technique was used for the preparation of polyarylates and brominated polyarylates. Polyarylates and brominated polyarylates were prepared by mixing a solution of diacid chloride such as terephthaloyl chloride, isophthaloyl chloride, or their mixture in dichloromethane with an aqueous alkaline solution of ,-bis(4-hydroxyphenyl)-1,4(or 1,3)-diisopropylbenzene or ,-bis(4-hydroxy-3,5-dibromophenyl)-1,4(or 1,3)-diisopropylbenzene using triethylbenzylammonium chloride as the phase transfer agent. Moderate to high molecular weight polyarylates with _inh up to 1.27 dL/g were obtained, and most of them could be cast into tough and flexible films depending on the polymer composition. In general, polymers containing more 1,3-isomer or isophthaloyl chloride moieties gave transparent and flexible films and had lower glass transition temperatures and higher solubility. Although these polymers have two isopropylidene linkages in their repeating units, they still exhibit moderately high thermal stability and show no obvious weight loss before 400 °C. The introduction of bromine on the polymer backbone caused a decrease of inherent viscosity, crystallinity, and thermal stability of the polyarylates, while causing an increase in glass transition temperature and a great enhancement of fire retardancy.     

Electrosynthesis of 4,4′-dinitroazobenzene on PbO2 electrodes

Parameters which affect the electrosynthesis of 4,4-dinitroazobenzene from p-nitroaniline on platinum and PbO₂ electrodes were investigated and optimum conditions were determined. Maximum conversion efficiency for electrosynthesis was 95% with a pure -PbO₂ electrode. It was found that the electrocatalytic activity of a PbO₂ electrode depends upon its / ratio and its degree of crystallinity. The effects of the added base and water on the conversion efficiency were also elucidated.     

Cobalt‐catalyzed amination of 1,3‐cyclohexanediol and 2,4‐pentanediol in supercritical ammonia

The onestep procedure of amination of bifunctional secondary alcohols to diamines has been investigated in a continuous fixedbed reactor. Application of supercritical NH₃ as a solvent and reactant suppressed catalyst deactivation and improved selectivities to amino alcohol intermediates, whereas selectivities to diamines remained poor (8–10%). The main reason for the low diamine selectivity of 1,3dihydroxy compounds is water elimination leading to undesired monofunctional products via ,unsaturated alcohol, ketone or amine intermediates. This side reaction does not occur with 1,4dihydroxy compounds which afford high aminol and diamine selectivities under similar conditions. Amination of secondary diols with ammonia was found to be faster, but less selective than that of the corresponding primary 1,3propanediol.     

Response of the European elm bark beetle,Scolytus multistriatus (Coleoptera: Scolytidae), to isomers and components of its pheromone

Laboratory bioassays (two methods) and field tests demonstrated synergistic action of the three components [(–)-4-methyl-3-heptanol (I); (–)-2,4-dimethyl-5-ethyl-6,8-dioxabicylo[3.2.1]octane (-multistriatin) (II); and (–)--cubebene (III)] of the pheromone bouquet ofScolytus multistriatus. Individually and in pairs the components were slightly attractive; I+II was clearly the most active doublet. Indirect evidence indicates that only one of the four enantiomers of I is active. Of the , , and isomers of II, only the is active. With the addition of compound I, slightly attractive extract from mated females became nearly as active as extract from virgin females.     

A miscibility study of ternary blends of polystyrene,tetramethylbisphenol-A polycarbonate,and poly(2,6-dimethyl-1,4-phenylene oxide)

Phase behaviorof ternary blends of polystyrene (PS), tetramethylbisphenol-A polycarbonate (TMPC), and poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) at two different temperatures (i.e., 210 and 300 °C, respectively) was studied by means of differential scanning calorimetry. Miscibility of the ternary blends at either temperature was found restricted to limited compositions, in agreement with simulated spinodal curves based on published values of interaction parameters. The limited ability of PS, which is separately miscible with TMPC and PPO at 210 °C, to act as a common solvent for the immiscible TMPC/PPO pair at this temperature was explained in terms of the disparity in PS/TMPC and PS/PPO pair interactions (i.e., the 'X effect).     

Experimental Study of Ignition of a Gasoline–Air Mixture in a Constant‐Volume Combustion Chamber

The characteristics of flamekernel development in a premixed gasoline–air mixture in a cylindrical constantvolume combustion chamber are measured. The experiments are performed with an initial temperature of 393 K, pressure of 6 bar, and equivalence ratio = 0.8 with the use of various ignition systems and spark plugs. The schlieren pictures of the process are presented, and the measured results for flame velocity, heatrelease rate, and mass fraction of the burnt fuel are analyzed.     

Polyimides based on “multiring” flexible diamines

The five benzene rings-containing (hereafter for convenience, referred to as five-ringrd) diamines ad-bis[4-(4-aminophenoxy)phenyl]-1,4 (or 1,3)-diisopropylbenzene (p- or m-3) were prepared by a nucleophilic substitution of ,-bis(4-hydroxyphenyl)-1, 4 (or 1,3)-diisopropylbenzene (p- or m-1) with p-chloronitrobenzene in the presence of K₂CO₃ and then hydro-reduced. The polyimides were synthesized from diamine 3 and various aromatic dianhydrides via the two-stage procedure that include ring-opening polyaddition in DMAc to give poly(amic acid)s, followed by thermal conversion to polyimides. The poly(amic acid)s had inherent viscosities of 0.63–1.54 dL/g depending on the dianhydrides used. Almost all the poly(amic acid)s could be solution-cast and thermally converted into transparent, flexible, and tough polyimide films. These polyimides have glass transition temperatures in the range of 186–290°C and almost no weight loss up to 500°C in air or nitrogen atmosphere. The polyimide obtained from pyromellitic dianhydride and diamine m-3 showed two endothermic peaks of 270 and 300°C on the diagram of differential scanning calorimetry (DSC), and the other polyimides showed no endotherms on their DSC traces.     

Enantioselective hydrogenation of α-ketoesters over Pt/alumina modified with cinchonidine: theoretical investigation of the substrate-modifier interaction

Enantio-differentiation in the asymmetric hydrogenation of -ketoesters to -hydroxyesters over platinum catalysts modified with cinchona-alkaloid modifiers occurs through interaction of the ketoester with the cinchona modifier. The structure of the probable transition complex has been calculated for the system methyl pyruvate (substrate) cinchonidine (modifier) using molecular mechanics and quantum chemistry techniques at both ab initio and semiempirical levels. The calculations suggest that protonated cinchonidine is energetically more likely to interact with the substrate and that the crucial interaction occurs via hydrogen bonding of the quinuclidine nitrogen and the oxygen of the -carbonyl moiety of methyl pyruvate. In this complex the methyl pyruvate is transformed into a half-hydrogenated species which is adsorbed on the platinum surface and on hydrogenation yields the product methyll actate. Theoretical studies indicate that adsorption of the complex leading to (R) -methyl lactate is energetically more favourable than that of the corresponding complex which yields (S) -methyl lactate, which may be the key for the enantio-differentiation.     

Epoxidation of Allylic Alcohols with TiO2–SiO2: Hydroxy-Assisted Mechanism and Dynamic Structural Changes During Reaction

Epoxidation of allylic alcohols and cyclohexene with TBHP and titania–silica aerogels containing 1 and 5wt% TiO₂ has been studied. For the oxidation of geraniol and cyclohexenol, the regio- and diastereoselectivities and kinetic data indicate an OH-assisted mechanism involving a dative bond between the OH group and the Ti site. This mechanism is disabled in the oxidation of cyclooctenol due to steric hindrance. The moderate regio- and diastereoselectivities of the aerogels, compared with those of TS-1 and the homogeneous model Ti(OSiMe₃)₄, are attributed to the presence of non-isolated Ti sites and to a silanol-assisted mechanism, according to which model the allylic alcohol is anchored to a neighboring SiOH group instead of the Ti-peroxo complex. Kinetic analysis of the initial transient period revealed rapid catalyst restructuring during the first few turnovers. A feasible explanation is the breaking of Si–O–Ti linkages of the carefully predried aerogels by water or TBHP, resulting in active Ti sites with remarkably different catalytic properties.     

Kinetics and Mechanism of Copolymerization of α-terpineol with Methylmethacrylate in Presence of Azobisisobutyronitrile as an Initiator

The radical copolymerization of -terpineol with methyl-methacrylate in xylene at 80±0.1C for 50 minutes in the presence of azobisisobutyronitrile (AIBN) follows ideal kinetics and results in the formation of a functional and random copolymer. The activation energy is 33 KJ/mole. The IR spectrum and NMR spectra of the copolymer(s) shows the bands at 1750 and 3400 cm^–1 for ester group of methylmethacrylate and alcoholic group of -terpineol and peaks at 3 to 4 for methoxy group and at 6.5 to 7.5 due to alcoholic group of methylmethacrylate and -terpineol repectively. The values of reactivity ratios, calculated by Kelen–Tüdos method, are r ₁ (MMA) = 0.18 and r ₂ (-terpineol) = 0.046. The Alfrey-Price; Q–e parameters for -terpineol has been calculated as 0.149 and 2.486. The mechanism of copolymerization has been elucidated and it is concluded that the double bond present in the monocyclic ring of -terpineol is an active site for copolymerization and the alcoholic group of -terpineol remain to give functional copolymer.     

Surface of a Titanium Target After Interaction with Shaped‐Charge Jet Particles

Coatings containing WC_1-x and W₂C_1-x tungsten carbides were produced on titanium targets by a shapedcharge explosion. The experiment used conical liners with a cone angle of 30° manufactured from a mixture of fine powders of tungsten, graphite, and ammonium nitrate. A comparative quantitative xray analysis of the top and bottom layers of the coating was performed. For the phase WC_1-x in the bottom layer, the value of the cubic unit cell parameter falls outside the range known in the literature. Microhardness in different segments of the target was studied.     

Transport of phosphorus forms and of nitrate through a clay soil under grass and cereal production

Many nutrients are lost from soil to water viatile drains. However, there are very few reliable studies of such phosphorus(P)losses under Swedish agriculture practices, especially in connection tofertiliser and slurry applications and related to nutrient balances. Tile drainlosses were measured from nine experimental plots in south-west Sweden; fourplots were measured for 7 years and five plots for 2–3 years. Cereals,mainly spring barley (Hordeum vulgare, L.) and oats(Avena sativa, L.), were grown in six plots, while oneplotwas cultivated with grass, timothy (Phleum pratense L.)andmeadow fescue (Festuca pratensis, L.), one with lucerne(Medicago sativa, L.) and meadow fescue (F.pratensis, L.), and the last one was a set-aside withgrass (Lolium perenne, L. and Trifoliumrepens, L.) that was neither fertilised nor used for crop removal.Attention was paid to the forms in which P was transported to water since thishas important ecological implications. Average losses of particulate P (PP)fromthe set-aside land was significantly lower than from the cerealproduction, but the average losses of soluble reactive P (SRP) and dissolvednonreactive P (DUP) were the same. Average loss of PP from the grass ley during 3years (0.09 kg per ha^–1 y^–1) wassignificantly less than the losses from cereal production. Total P loss of 0.3kg per ha^–1 y^–1 was equal to the averagelossfrom the Swedish monitoring network of observation fields. Compared to theaverage nitrate-nitrogen (NO₃-N) leaching, which was 7 kg perha^–1 y^–1 from cereals, the NO₃-Nleaching was very low from the plots with lucerne-grass and set-aside.After applying and directly ploughing in 80 kg ha^–1 ofsuperphosphate for cereal production in November 1998, 0.6–1.8 kgSRP ha^–1 y^–1 was lost through the drain tiles.Surface application of cattle slurry in spring 1999 to the grass ley alsoresulted in a very pronounced increased base level of SRP. This paper documentsthe importance of applying slurry during dry conditions and of placingfertiliser into the soil according to crop requirements in the time perspectiveof one year.     

Synergistic interaction between potato glycoalkaloidsα-solanine andα-chaconine in relation to destabilization of cell membranes: Ecological implications

In studies of the lysis of rabbit erythrocytes, red beet cells, andPenicillium notatum protoplasts by the potato glycoalkaloids -solanine and -chaconine, the latter was consistently the more membrane-disruptive compound and erythrocytes the more susceptible cell type. A 11 mixture of solanine and chaconine produced pronounced synergistic effects in all three test systems. In beet cells, such effects were apparent from an early stage of treatment and persisted over a period of several hours. With erythrocytes and fungal protoplasts, the synergism was maximal with mixtures containing approximately 70% chaconine, whereas with beet cells it peaked at approximately 40% chaconine. Synergistic interactions between solanine and chaconine also occurred with regard to cholesterol binding in vitro, with a maximum response corresponding to the 50% mixture. The implications of these findings for the nature and efficacy of chemical defense systems in plants are discussed.     

Oxidation of α- and β-pinene catalyzed by MnIII (Salen) Cl·H2O

The cationic complex Mn^III (Salen) is a very effective catalyst for the oxidation of both- and-pinene. The higher selectivity towards epoxide formation supports the rebound oxygen mechanism. A turnover of 40 was obtained for both compounds after 16 h of reaction with a molar ratio 10.011 (feedstock: catalyst: iodosobenzene) and conversions between 50 and 60% were observed. A very high selectivity (55%) was determined for epoxide formation from -pinene. The good selectivity observed for myrtanal isomers (6.5 and 23.2%) from-pinene is related to the prior formation of the 1,2-epoxides.     

Nanocomposite route to the stabilization of porous ϑ-alumina

Stabilization of -alumina phase by silica was studied in nanocomposite (diphasic) alumina-silica gels by XRD and BET surface areas measurements. Five wt.% of silica (22 nm particles) increased the crystallization temperature of to -alumina by about 100°C from boehmite (10 nm particles) derived alumina. Stabilization of -alumina was caused by the formation of intimate contact (Al-O-Si) between components by diffusion of silica into the defect alumina structure.Also with the Department of Agronomy.