Dry etching of TaN thin film using CH4/Ar inductively coupled plasma

In this research, we investigated the TaN etch rate and selectivity with under layer (HfO₂) and mask material (SiO₂) in inductively coupled CH₄/Ar plasma. As the CH₄ content increased from 0% to 80% in CH₄/Ar plasma, the TaN etch rate was increased from 11.9 to 22.8 nm/min. From optical emission spectroscopy (OES), the intensities for CH [431 nm] and H [434 nm] were increased with the increasing CH₄ content from 0% to 100% in CH₄/Ar plasma. The results of x-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) showed no accumulation of etch by-products from the etched surface of TaN thin film. As a result of OES, AES and XPS analysis, we observed the etch by-products from the surfaces, such as Ta-N-CH and N-CH bonds. Based on the experimental results, the TaN etch was dominated by the chemical etching with the assistance of Ar sputtering in reactive ion etching mechanism.     

Dry etching characteristics of HfAlO3 thin films in BCl3/Ar plasma using inductively coupled plasma system

In this study, we monitored the HfAlO₃ etch rate and selectivity to SiO₂ as a function of the etch parameters (gas mixing ratio, RF power, DC-bias voltage, and process pressure). A maximum etch rate of 52.6 nm/min was achieved in the 30% BCl₃/(BCl₃ + Ar) plasma. The etch selectivity of HfAlO₃ to SiO₂ reached 1.4. As the RF power and the DC-bias voltage increased, the etch rate of the HfAlO₃ thin film increased. As the process pressure decreased, the etch rate of the HfAlO₃ thin films increased. The chemical state of the etched surfaces was investigated by X-ray Photoelectron Spectroscopy (XPS). According to the results, the etching of HfAlO₃ thin films follows the ion-assisted chemical etching mechanism.     

Etch characteristics of HfO2 thin films by using CF4/Ar inductively coupled plasma

In this study, we carried out an investigation of the etching characteristics (etch rate, selectivity) of HfO₂ thin films in the CF₄/Ar inductively coupled plasma (ICP). The maximum etch rate of 54.48 nm/min for HfO₂ thin films was obtained at CF₄/Ar (=20:80%) gas mixing ratio. At the same time, the etch rate was measured as function of the etching parameters such as ICP RF power, DC-bias voltage, and process pressure. The X-ray photoelectron spectroscopy analysis showed an efficient destruction of the oxide bonds by the ion bombardment as well as an accumulation of low volatile reaction products on the etched surface. Based on these data, the chemical reaction was proposed as the main etch mechanism for the CF₄-containing plasmas.     

Dry etching of magnesium oxide thin films by using inductively coupled plasma for buffer layer of MFIS structure

Magnesium oxide thin film has been widely used as a buffer layer and substrate for growing various thin film materials because of very low Gibbs free energy, low dielectric constant and low refractive index. The investigations of the MgO etching characteristics in BCl₃/Ar plasma were carried out using the inductively coupled plasma system. It was found that the increasing BCl₃ in the mixing ratio of BCl₃/Ar plasma causes monotonic MgO etch rate. The results showed in the BCl₃-rich plasma that the etching process is dominantly supplied by the chemical pathway through the ion-assisted chemical reaction.     

Dry etching properties of TiO2 thin films in O2/CF4/Ar plasma

In this work, the etching properties of titanium dioxide (TiO₂) thin film in additions of O₂ at CF₄/Ar plasma were investigated. The maximum etch rate of 179.4 nm/min and selectivity of TiO₂ of 0.6 were obtained at an O₂/CF₄/Ar (=3:16:4 sccm) gas mixing ratio. In addition, the etch rate and selectivity were measured as a function of the etching parameters, such as the RF power, DC-bias voltage, and process pressure. The efficient destruction of the oxide bonds by ion bombardment, which was produced from the chemical reaction of the etched TiO₂ thin film, was investigated by X-ray photoelectron spectroscopy. To determine the re-deposition of sputter products and reorganization of such residues on the surface, the surface roughness of TiO₂ thin film were examined using atomic force microscopy.     

Characteristics of GaN thin films by inductively coupled plasma etching with Cl2/BCl3 and Cl2/Ar

GaN thin films were etched by inductively coupled plasma (ICP). The effects of BCl₃ and Ar with different Cl₂ fraction are studied and compared. The ICP power and RF power are also altered to investigate the different effects by using Cl₂/BCl₃ or Cl₂/Ar as etching gases. The etch rate and surface morphology of the etched surface are characterized by using surface profiler, scanning electron microscopy and atomic force microscopy. The root-mean-square roughness values are systematically compared. It is found that the etch rates of Cl₂/Ar are higher than that of the Cl₂/BCl₃ in the Cl₂ fraction ranging from 10 to 90%. When the ICP power is increased, the RMS roughness of GaN surface after ICP etching shows reverse trend between Cl₂/BCl₃ and Cl₂/Ar gas mixture. The results indicate quite different features using Cl₂/BCl₃ and Cl₂/Ar for GaN ICP etcing under the same conditions.     

Dry etching of TiN in N2/Cl2/Ar adaptively coupled plasma

We investigated the N₂ additive effect on the etch rates of TiN and SiO₂ and etch profile of TiN in N₂/Cl₂/Ar adaptively coupled plasma (ACP). The mixing ratio of Cl₂ and Ar was fixed at 75 and 25 sccm, respectively. The N₂ flow rate was increased from 0 to 9 sccm under the constant pressure of 10 mTorr. As N₂ flow rate was increased in N₂/Cl₂/Ar plasma, the etch rate of TiN was linearly increased, but that of SiO₂ was increased non-monotonically. The etch profile and the compositional changes of TiN was investigated with field emission-scanning electron microscope (FE-SEM), FE-Auger electron spectroscopy (FE-AES) and x-ray photoelectron spectroscopy (XPS). When 9 sccm N₂ was added into Cl₂/Ar, a steep etch profile and clean surface of TiN was obtained. In addition, the signals of TiN and Ti were disappeared in FE-AES and XPS when N₂ additive flow into Cl₂/Ar was above 6 sccm. From the experimental data, the increase in TiN etch rate was mainly caused by the increase of desorption and evacuation rate of etch by products because of the increased effective pumping speed. The etch mechanism of TiN in N₂/Cl₂/Ar ACP plasma can be concluded as the ion enhanced chemical etch.     

Etch characteristics of FePt magnetic thin films using inductively coupled plasma reactive ion etching

Etch characteristics of L10 FePt thin films masked with TiN films were investigated using an inductively coupled plasma (ICP) reactive ion etching in a CH₃OH/Ar plasma. As the CH₃OH gas was added to Ar, the etch rates of FePt thin films and TiN hard mask gradually decreased, and the etch profile of FePt films improved with high degree of anisotropy. With increasing ICP rf power and dc-bias voltage to substrate and decreasing gas pressure, the etch rate increased and the etch profile becomes vertical without any redepositions or etch residues. Based on the etch characteristics and surface analysis of the films by X-ray photoelectron spectroscopy, it can be concluded that the etch mechanism of FePt thin films in a CH₃OH/Ar gas does not follow the reactive ion etch mechanism but the chemically assisted sputter etching mechanism, due to the chemical reaction of FePt film with CH₃OH gas.     

Etch characteristics of IrMn thin films using an inductively coupled plasma of CH3OH/Ar

An inductively coupled plasma reactive ion etching of IrMn magnetic thin films patterned with Ti hard mask was studied in a CH₃OH/Ar gas mix. As the CH₃OH concentration increased, the etch rates of IrMn thin films and Ti hard mask decreased, while the etch profiles improved with high degree of anisotropy. The effects of coil rf power, dc-bias voltage to substrate and gas pressure on the etch characteristics were investigated. The etch rate increased and the etch profile improved with increasing coil rf power, dc-bias voltage and decreasing gas pressure. X-ray photoelectron spectroscopy revealed that the chemical reaction between IrMn films and CH₃OH gas occurred, leading to the clean and good etch profile with high degree of anisotropy of 90°.     

Inductively coupled plasma reactive ion etching of titanium thin films using a Cl2/Ar gas

Inductively coupled plasma reactive ion etching of titanium thin films patterned with a photoresist using Cl₂/Ar gas was examined. The etch rates of the titanium thin films increased with increasing the Cl₂ concentration but the etch profiles varied. In addition, the effects of the coil rf power, dc-bias voltage and gas pressure on the etch rate and etch profile were investigated. The etch rate increased with increasing coil rf power, dc-bias voltage and gas pressure. The degree of anisotropy in the etched titanium films improved with increasing coil rf power and dc-bias voltage and decreasing gas pressure. X-ray photoelectron spectroscopy revealed the formation of titanium compounds during etching, indicating that Ti films etching proceeds by a reactive ion etching mechanism.     

Dry etch properties of IZO thin films in a CF4/Ar adaptively coupled plasma system

In this study, we investigated to the etch characteristics of indium zinc oxide (IZO) thin films in a CF₄/Ar plasma, namely, etch rate and selectivity toward SiO₂. A maximum etch rate of 76.6 nm/min was obtained for IZO thin films at a gas mixture ratio of CF₄/Ar (25:75%). In addition, etch rates were measured as a function of etching parameters, including adaptively coupled plasma chamber pressure. X-ray photoelectron spectroscopy analysis showed efficient destruction of the oxide bonds by ion bombardment, as well as accumulation of low volatile reaction products on the surface of the etched IZO thin films. Field emission Auger electron spectroscopy analysis was used to examine the efficiency of ion-stimulated desorption of the reaction products.     

The dry etching property of TiO2 thin films using metal-insulator-metal capacitor in inductively coupled plasma system

In this work, we investigated the etching characteristics of TiO₂ thin films and the selectivity of TiO₂ to SiO₂ in a BCl₃/Ar inductively coupled plasma (ICP) system. The maximum etch rate of 84.68 nm/min was obtained for TiO₂ thin films at a gas mixture ratio of BCl₃/Ar (25:75%). In addition, etch rates were measured as a function of etching parameters, such as the RF power, DC-bias voltage and process pressure. Using the X-ray photoelectron spectroscopy analysis the accumulation of chemical reaction on the etched surface was investigated. Based on these data, the ion-assisted physical sputtering was proposed as the main etch mechanism for the BCl₃-containing plasmas.     

Etch characteristics of indium zinc oxide thin films using inductively coupled plasma of a Cl2/Ar gas

Inductively coupled plasma reactive ion etching of indium zinc oxide (IZO) thin films masked with a photoresist was performed using a Cl₂/Ar gas. The etch rate of the IZO thin films increased as Cl₂ gas was added to Ar gas, reaching a maximum at 60% Cl₂ and decreasing thereafter. The degree of anisotropy in the etch profile improved with increasing coil rf power and dc-bias voltage. Changes in pressure had little effect on the etch profile. X-ray photoelectron spectroscopy confirmed the formation of InCl₃ and ZnCl₂ on the etched surface. The surface morphology of the films etched at high Cl₂ concentrations was smoother than that of the films etched at low Cl₂ concentrations. These results suggest that the dry etching of IZO thin films in a Cl₂/Ar gas occurs according to a reactive ion etching mechanism involving ion sputtering and a surface reaction.     

GaN etch rate and surface roughness evolution in Cl2/Ar based inductively coupled plasma etching

Cl₂/Ar based inductively coupled plasma (ICP) etching of GaN is investigated using photoresist mask in a consequential restricted domain of pressure < 1.2 Pa and radio frequency (RF) sample power < 100 W, for selective mesa etching. The etch characteristics and root-mean-square (rms) surface roughness are studied as a function of process parameters viz. process pressure, Cl₂ percentage in total flow rate ratio, and RF sample power at a constant ICP power, to achieve moderate GaN etch rate with anisotropic profiles and smooth surface morphology. The etch rate and resultant surface roughness of etched surface increased with pressure mainly due to dominant reactant limited etch regime. The etch rate and surface roughness show strong dependence on RF sample power with the former increasing and the later decreasing with the applied RF sample power up to 80 W. The process etch yield variation with applied RF sample power is also reported. The studied etch parameters result in highly anisotropic mesa structures with Ga rich etched surface.     

Dry etching of TiN in N2/Cl2/Ar adaptively coupled plasma

We investigated the N₂ additive effect on the etch rates of TiN and SiO₂ and etch profile of TiN in N₂/Cl₂/Ar adaptively coupled plasma (ACP). The mixing ratio of Cl₂ and Ar was fixed at 75 and 25 sccm, respectively. The N₂ flow rate was increased from 0 to 9 sccm under the constant pressure of 10 mTorr. As N₂ flow rate was increased in N₂/Cl₂/Ar plasma, the etch rate of TiN was linearly increased, but that of SiO₂ was increased non-monotonically. The etch profile and the compositional changes of TiN was investigated with field emission-scanning electron microscope (FE-SEM), FE-Auger electron spectroscopy (FE-AES) and x-ray photoelectron spectroscopy (XPS). When 9 sccm N₂ was added into Cl₂/Ar, a steep etch profile and clean surface of TiN was obtained. In addition, the signals of TiN and Ti were disappeared in FE-AES and XPS when N₂ additive flow into Cl₂/Ar was above 6 sccm. From the experimental data, the increase in TiN etch rate was mainly caused by the increase of desorption and evacuation rate of etch by products because of the increased effective pumping speed. The etch mechanism of TiN in N₂/Cl₂/Ar ACP plasma can be concluded as the ion enhanced chemical etch.     

A study on the etch characteristics of HfAlO3 dielectric thin film in Cl2/Ar gas chemistry using inductively coupled plasma system

Thin films of HfAlO₃, a high-k material, were etched using inductively-coupled plasma. The dry etching mechanism of the HfAlO₃ thin film was studied by varying the Cl₂/Ar gas mixing ratio, RF power, direct current bias voltage, and process pressure. The maximum etch rate of the HfAlO₃ thin film was 16.9 nm/min at a C1₂/(C1₂ + Ar) ratio of 80%. Our results showed that the highest etch rate of the HfAlO₃ thin films was achieved by reactive ion etching using Cl radicals, due to the high volatility of the metal-chlorides. Consequently, the increased chemical effect caused an increase in the etch rate of the HfAlO₃ thin film. Surface analysis by x-ray photoelectron spectroscopy showed evidence that Hf, Al and O reacted with Cl and formed nonvolatile metal-oxide compounds and volatile metal-chlorides. This effect may be related to the concurrence of chemical and physical pathways in the ion-assisted chemical reaction.     

Cl2/Ar感应耦合等离子体刻蚀InP工艺研究

采用Cl2／Ar感应耦合等离子体对InP进行了刻蚀。讨论了直流自偏压、ICP功率、气体总流量和气体组分等因素对刻蚀速率和粗糙度的影响。结果表明Cl2／Ar气体组分是决定刻蚀效果的重要因素。当Cl2含量为30％左右时,刻蚀中的物理溅射与化学反应过程趋于平衡,刻蚀速率处于峰值区,同时刻蚀粗糙度也可达到最小值。SEM照片显示刻蚀表面光洁。侧壁陡直。     

Etch characteristics of TiN/Al2O3 thin film by using a Cl2/Ar adaptive coupled plasma

In this study, we carried out an investigation in the etching characteristics of TiN thin films in a C1₂/Ar adaptive coupled plasma. The maximum etch rate of the TiN thin films was 768 nm/min at a gas mixing ratio of C1₂ (75%)/Ar (25%). At the same time, the etch rate was measured as functions of the various etching parameters. The X-ray photoelectron spectroscopy analysis showed the efficient destruction of the oxide bonds by the ion bombardment as well as the accumulation of low volatile reaction products on the etched surface. Field emission Auger electron spectroscopy analysis was used to examine the efficiency of the ion-stimulated desorption of the reaction products.     

Inductively coupled plasma reactive ion etching of ZnO films in HBr/Ar plasma

The etching characteristics of ZnO thin films were examined in an HBr/Ar gas mix using an inductively coupled plasma reactive ion etching system. The etch rate and etch profile were systematically investigated as a function of gas concentration. In addition, the effects of etch parameters such as coil rf power, dc-bias voltage, and gas pressure were studied. As the HBr concentration increased, the etch rate of the ZnO films gradually decreased while the etch profile was improved. Surface analyses including X-ray photoelectron spectroscopy and atomic force microscopy were employed to elucidate the etch mechanism of ZnO in an HBr/Ar chemistry.