Raman Study of Grain Size Effects in the Melting Behavior of 15Na2CO3-10BaCO3-75SiO2 Batches

By means of Raman spectroscopy the melting behavior of 15Na₂CO₃−10BaCO₃−75SiO₂ batches with different grain sizes of raw materials was investigated both qualitatively and quantitatively. The results show that the reaction rate at low temperatures ( T ≤800° to 900°C) increases when finer grains of all raw materials are used; upon pelletizing the fine batch the reaction rate increases even further. At high temperatures ( T > 900°C) the grain size of SiO₂ is the main determining factor, the melting rate being increased when fine SiO₂ grains are used.     

Phase Equilibria and Ionic Conductivity in the System ZrO2−Yb2O3−Y2O3

The phase equilibria in the zirconia-rich part of the system ZrO₂−Yb₂O₃−Y₂O₃ were determined at 1200°, 1400°, and 1650°C. The stabilizing effects of Yb₂O₃ and Y₂O₃ were found to be quite similar with <10 mol% of either being necessary to fully stabilize the cubic fluorite-structure phase at 1200°C. The two binary ordered phases, Zr₃Yb₄O₁₂ and Zr₃Y₄O₁₂, are completely miscible at 1200°C. These were the only binary or ternary phases detected. The ionic conductivities of ternary specimens in this system were measured using the complex impedance analysis technique. For a given level of total dopant, the substitution of Yb₂O₃ for Y₂O₃ gives only minor increases in specimen conductivity.     

Phase Transitions in Pb(Mg1/3Nb2/3)O3–PbTiO3 Studied by Low-Frequency Internal Friction Measurement

The low-frequency internal friction (0.1 Hz< f <10 Hz) of (100− x %)Pb(Mg_1/3Nb_2/3)O₃− x %PbTiO₃ ( x =0, 13, 23, 33) ceramics has been measured in the temperature range between 90 and 500 K. All of the internal friction peaks show a height that is inversely proportional to the measurement frequency, thus they can be attributed to first-order phase transitions. The phase transitions between rhombohedral, monoclinic, and tetragonal phases in ceramics with x =33 occur over a very broad temperature range from 150 to 400 K, indicating that the giant piezoelectric effect in this material may be attributed to a field-induced phase transition process.     

Massive Transformation in the Y2O3-Bi2O3 System

Cubic solid solutions in the Y₂O₃-Bi₂O₃ system with ∼25% Y₂O₃ undergo a transformation to a rhombohedral phase when annealed at temperatures ≤ 700°C. This transformation is composition-invariant and is thermally activated, and the product phase can propagate across matrix grain boundaries, indicating that there is no special crystallo-graphic orientation relationship between the product and the parent phases. Based on these observations, it is proposed that cubic → rhombohedral phase transformation in the Y₂O₃-Bi₂O₃ system is a massive transformation. Samples of composition 25% Y₂O₃-75% Bi₂O₃ with and without aliovalent dopants were annealed at temperatures ≤ 700°C for up to 10000 h. ZrO₂ as a dopant suppressed while CaO and SrO as dopants enhanced the kinetics of phase transformation. The rate of cubic/rhombohedra1 interface migration (growth rate or interface velocity) was also similarly affected by the additions of dopants; ZrO₂ suppressed while CaO enhanced the growth rate. Diffusion studies further showed that ZrO₂ suppressed while CaO enhanced cation interdiffusion coefficient. These observations are rationalized on the premise that cation interstitials are more mobile compared to cation vacancies in cubic bismuth oxide. The maximum growth rate measured was ∼10⁻¹⁰ m/s, which is orders of magnitude smaller than typical growth rates measured in metallic alloys. This difference is explained in terms of substantially lower diffusion coefficients in these oxide systems compared to metallic alloys.     

Influence of Non-Stoichiometry on the Structure and Properties of Ba(Zn1/3Nb2/3)O3 Microwave Dielectrics: I. Substitution of Ba3W2O9

A narrow region of Zn-vacancy-containing cubic perovskites was formed in the (1− x )Ba₃(ZnNb₂)O₉−( x )Ba₃W₂O₉ system up to 2 mol% substitution ( x =0.02). The introduction of cation vacancies enhanced the stability of the 1:2 B-site ordered form of the structure, Ba(Zn_{1− x} □ _x )_1/3(Nb_{1− x} W _x )_2/3O₃, which underwent an order–disorder transition at 1410°C, ∼35° higher than pure Ba(Zn_1/3Nb_2/3)O₃. The Zn vacancies also accelerated the kinetics of the ordering reaction, and samples with x =0.006 comprised large ordered domains with a high lattice distortion ( c/a =1.226) after a 12 h anneal at 1300°C. The tungstate-containing solid solutions can be sintered to a high density at 1390°C, and the resultant ordered ceramics exhibit some of the highest microwave dielectric Q factors ( Q × f =1 18 000 at 8 GHz) reported for a niobate-based perovskite.     

Kinetics of {001} Pb(Mg1/3Nb2/3)O3–35 mol% PbTiO3 Single Crystals Grown by Seeded Polycrystal Conversion

The kinetics of {001}-oriented Pb(Mg_1/3Nb_2/3)O₃–35 mol% PbTiO₃ (PMN–35PT) single crystals grown by seeded polycrystal conversion were systematically quantified as a function of excess PbO liquid phase. The coarsening behavior of the corresponding matrix grains was similarly quantified. Single-crystal seed plates were embedded in a matrix of PMN-35PT with varying amounts of liquid phase (PbO) content in the range of 0 to 5 vol% and annealed at 1150°C for 0–10 h. Apparent maxima in the growth rates were observed at a PbO content of ∼3 vol% for both the single crystal and matrix grains. In both cases, the growth data were found to most closely follow cubic growth kinetics. Implications regarding the effect of PbO volume fraction on the matrix and single-crystal growth mechanisms are discussed.     

A Novel Temperature-Compensated Microwave Dielectric (1−x)(Mg0.95Ni0.05)TiO3−xCa0.6La0.8/3TiO3 Ceramics System

The microstructure and microwave dielectric properties of a (1− x )(Mg_0.95Ni_0.05)TiO₃− x Ca_0.6La_0.8/3TiO₃ ceramics system have been investigated. The system was prepared using a conventional solid-state ceramic route. In order to produce a temperature-stable material, Ca_0.6La_0.8/3TiO₃ was added for a near-zero temperature coefficient (τ_f). With partial replacement of Mg²⁺ by Ni²⁺, the dielectric properties of the (1− x )(Mg_0.95Ni_0.05)TiO₃− x Ca_0.6La_0.8/3TiO₃ ceramics can be promoted. The microwave dielectric properties are strongly correlated with the sintering temperature and the composition. An excellent Q × f value of 118,000 GHz can be obtained for the system with x =0.9 at 1325°C. For practical application, a dielectric constant (ɛ_r) of 24.61, a Q × f value of 102,000 GHz, and a temperature coefficient of resonant frequency (τ_f) of −3.6 ppm/°C for 0.85(Mg_0.95Ni_0.05)TiO₃−0.15Ca_0.6La_0.8/3TiO₃ at 1325°C are proposed. A parallel-coupled line band-pass filter is designed and simulated using the proposed dielectric to study its performance.     

Fusion and Vaporization Characteristics of ZrTe3O8

The only intermediate phase stable in air in the system ZrO₂−TeO₂ is ZrTe₃O₈ with a cubic, distorted, fluorite-type structure. The compound melts congruently at 1014°± 5°C to an unstable liquid. Vaporization occurs, with loss of TeO₂, at high temperatures with an activation energy of 64 kcal per mole of ZrTe₃O₈. No glass formation was observed in the system.     

The System HfO2-Y2O3-Er2O3

A mathematical model of the liquidus surface based on a reduced polynomial method was proposed for the system HfO₂-Y₂O₃-Er₂O₃. The results of calculations according to this model agree fairly well with the experimental data. Phase equilibria in the system HfO₂-Y₂O₃-Er₂O₃ were studied on melted (as-cast) and annealed samples using X-ray diffraction (at room and high temperatures) and micro-structural and petrographic analyses. The crystallization paths in the system HfO₂-Y₂O₃-Er₂O₃ were established. The system HfO₂-Y₂O₃-Er₂O₃ is characterized by the formation of extended solid solutions based on the fluorite-type (F) form of HfO₂ and cubic (C) and hexagonal (H) forms of Y₂O₃ and Er₂O₃. The boundary curves of these solid solutions have the minima at 2370°C (15. 5 mol% HfO₂, 49. 5 mol% Y₂O₃) and 2360°C (10. 5 mol% HfO₂, 45. 5 mol% Y₂O₃). No compounds were found to exist in the system investigated.     

Phase Relations in the Pyrochlore-Rich Part of the Bi2O3−TiO2−Nd2O3 System

In this study we used solid-state synthesis to determine the phase relations in the pyrochlore-rich part of the Bi₂O₃−TiO₂−Nd₂O₃ system at 1100°C. The samples were analyzed using X-ray powder diffraction and scanning electron microscopy with energy- and wavelength-dispersive spectroscopy. A single-phase pyrochlore ceramic was obtained with the addition of 4.5 mol% of Nd₂O₃. We determined the solubility limits for the three solid solutions: (i) the pyrochlore solid solution Bi_{(1.6–1.08 x )}Nd _x Ti₂O_{(6.4+0.3 x )}, where 0.25< x <0.96; (ii) the solid solution Bi_{4− x} Nd _x Ti₃O₁₂, where 0< x <2.6; and (iii) the Nd_{2− x} Bi _x Ti₂O₇ solid solution, where 0< x <0.35. The determined phase relations in the pyrochlore-rich part are presented in a partial phase diagram of the Bi₂O₃−TiO₂−Nd₂O₃ system in air at 1100°C.     

Solid-Liquid Equilibria in the System Si3N4-AlN-Si02-A12O3

Solid-liquid equilibria at 1750°C and subsolidus phase relations in the system Si₃N₄−AlN-SiO₂−Al₂O₃ were determined for the composition region bounded by the β-Si₃N₄ solid solution line and silica-alumina join X-ray diffraction and optical microscopy were used to determine the phases present in specimens cooled rapidly after equilibration. The extent of a single liquid-phase region and the tie lines for the βsolid solution + liquid field at 1750°C were established from quantitative X-ray diffractometry and lattice parameter measurements of βsolid solutions in equilibrium with liquid. The results were corroborated by optical microscopy and melting behavior observations. A new composition, Si₁₂Al₁₈O₃9N₈, is suggested for the x₁ phase. The lowest melting temperature in the system is ≅ 1480°C and the corresponding composition is 10 eq% Al-90 eq%O.     

Microstructural Evolution in a ZrO2 Wt% Y2O3 Ceramic

Several unusual microstructural features, i.e., 90° tetragonal ZrO₂ twins containing antiphase domain boundaries, tetragonal ZrO₂ precipitates in a colony morphology, and precipitate-free zones at the perimeter of cubic ZrO₂ grains containing fine tetragonal ZrO₂ precipitates, were observed in a single ZrO₂-12 wt% Y₂O₂ ceramic annealed at 1550°, 1400°, and 1250°C, respectively. The type of phase transformation responsible for each microstructural feature is described.     

Phase Equilibration in ZrO2-Y2O3 Alloys by Liquid-Film Migration

The tetragonal ( t ) and cubic ( c ) ZrO₂ solid solutions in two-phase ZrO₂-8 wt% Y₂O₃ ceramics have low and high solute content, respectively. Annealing samples sintered at 1600°C between 700° and 1400°C requires a change in the volume fraction of the coexisting phases, as well as their equilibrium Y₂O₃ content. The enrichment in Y₂O₃ content of the c -ZrO₂ grains is accomplished by liquid-film migration involving the ubiquitous silicate grain-boundary phase, while the volume fraction of t -ZrO₂ increases by the nucleation and growth of cap-shaped t -ZrO₂ lenses. The interfaces between the c -ZrO₂ matrix and the growing t -ZrO₂ lenses are semicoherent.     

Glass Formation and Properties of Chalcogenides in a GeSe2–As2Se3–PbSe System

The glass-forming region in a GeSe₂–As₂Se₃–PbSe system was determined, and the dependence of properties on the composition as a formula of 20 GeSe₂–(80− x )As₂Se₃− x PbSe ( x =0–30) was investigated. Measurements include density, differential scanning calorimetry, X-ray diffraction, Vis-NIR, and IR transmission spectra. A fairly large glass-forming region was obtained where the higher lead content could be introduced into the system in the As₂Se₃-rich region than in the GeSe₂-rich region. With the introduction of PbSe, the density of glass increased and the calculated molar volume decreased while the crystallization tendency increased, which was indicated by the decreasing Δ T ( T _x− T _g). The activation energy of crystallization and the Avrami exponents were also obtained using the modified Ozawa equation. Under proper annealing conditions, suitable IR transmittance glass–ceramics were obtained.     

Effect of Seeding Sr2KNb5O15 on the Phase Formation and Microstructural Development in Reactive Sintering of Sr2NaNb5O15 Ceramics

The phase formation, densification behavior, and microstructure development of Sr₂NaNb₅O₁₅ (SNN) ceramics in both 10 wt% acicular Sr₂KNb₅O₁₅ (SKN) seed-containing and unseeded systems were investigated in this work. SNN ceramics were reactively sintered from SrNb₂O₆ and NaNbO₃ powders. The results show that the acicular SKN seeds not only accelerate SNN phase formation but also promote the densification at lower temperature. In reactive sintering, the acicular SKN seeds prepared by the molten salt synthesis method can give rise to the formation of a liquid phase and provide the structural framework for the grain growth of ceramics, leading to the formation of large anisotropic grains (>80 μm) in ceramics sintered at 1340°C. However, there are no such large anisotropic grains obtained in the SKN-free system. Observation of the large anisotropic grain growth is explained by the liquid-phase-assisted growth mechanism. For comparison, the microstructure evolution in the system with 10 wt% SKN seed, which was prepared by the conventional mixed-oxide method and without acicular morphology, was also investigated to further support the new growth mechanism.     

Preparation of Dense BaTiO3 Ceramics with Submicrometer Grains by Spark Plasma Sintering

Dense BaTiO₃ ceramics consisting of submicrometer grains were prepared using the spark plasma sintering (SPS) method. Hydrothermally prepared BaTiO₃ (0.1 and 0.5 µm) was used as starting powders. The powders were densified to more than similar/congruent95% of the theoretical X-ray density by the SPS process. The average grain size of the SPS pellets was less than similar/congruent1 µm, even by sintering at 1000-1200°C, because of the short sintering period (5 min). Cubic-phase BaTiO₃ coexisted with tetragonal BaTiO₃ at room temperature in the SPS pellets, even when well-defined tetragonal-phase BaTiO₃ powder was sintered at 1100° and 1200°C and annealed at 1000°C, signifying that the SPS process is effective for stabilizing metastable cubic phase. The measured permittivity was similar/congruent7000 at 1 kHz at room temperature for samples sintered at 1100°C and showed almost no dependence on frequency within similar/congruent10⁰-10⁶ Hz; the permittivity at 1 MHz was 95% of that at 1 kHz.     

High-Pressure Sintering of Nanocrystalline γAl2O3

High-pressure sintering of nanocrystalline γ-A1₂O₃ has been studied over a temperature range of 923-1323 K and at a pressure of 1 GPa. The γ-Al₂O₃ to α-Al₂O₃ transformation temperature changed from 1473 K without pressure to ∼1023 K at 1 GPa. Full density was obtained at 1273 and 1323 K in 10 min. The microhardness value of fully dense α-alumina with a grain size of 142 nm was found to be 25.3 ± 0.8 GPa. The Hall-Petch slope for the very fine grain size range is different from that of the coarse-grained alumina.     

Structure–Property Relationships of BaTi1−2yGayNbyO3 (0≤y≤0.35) Ceramics

BaTi_{1−2 y} Ga _y Nb _y O₃ (BTGN) (0≤ y ≤0.35) powders were synthesized at 1300°C by the conventional solid-state method. Room temperature x-ray diffraction patterns for y ≤0.025 and 0.05≤ y ≤0.30 can be indexed as the tetragonal ( P 4 mm ) and cubic ( Pm     m ) polymorphs of BaTiO₃, respectively, whereas y =0.35 consists of a mixture of the cubic polymorph of BaTiO₃ and an 8H hexagonal-type perovskite ( P 6₃/ mcm ) isostructural with Ba₈Ti₃Nb₄O₂₄. Scanning electron microscopy shows the microstructures of BTGN ceramics ( y ≤0.30) sintered at 1500°C to consist of fine grains (1–3 μm) within a narrow grain size and shape distribution. Room temperature transmission electron microscopy for y ≤0.08 reveals core–shell structures and (111) twins in some grains; however, their relative volume decreases with y . Energy dispersive spectroscopy reveals the cores to be Ga and Nb deficient with respect to y . For y >0.08 there is no evidence of core–shell structures, however, some grains have a high density of dislocations, consistent with chemical inhomogeneity. BTGN ceramics exhibit a diverse range of dielectric behavior in the temperature range 120–450 K and can be subdivided into two groups. 0.025≤ y ≤0.15 display modest ferroelectric relaxor-type behavior, with high room temperature permittivity, ɛ₂₅', (>300 at 10 kHz), whereas 0.25≤ y ≤0.30 are temperature and frequency stable dielectrics with ɛ₂₅'<100 that resonate at microwave frequencies with modest quality factors, Q × f , ∼3720 GHz (at ∼5 GHz) for y =0.30.     

High-Temperature Chemistry and Oxidation of ZrB2 Ceramics Containing SiC, Si3N4, Ta5Si3, and TaSi2

The effect of Si₃N₄, Ta₅Si₃, and TaSi₂ additions on the oxidation behavior of ZrB₂ was characterized at 1200°–1500°C and compared with both ZrB₂ and ZrB₂/SiC. Significantly improved oxidation resistance of all Si-containing compositions relative to ZrB₂ was a result of the formation of a protective layer of borosilicate glass during exposure to the oxidizing environment. Oxidation resistance of the Si₃N₄-modified ceramics increased with increasing Si₃N₄ content and was further improved by the addition of Cr and Ta diborides. Chromium and tantalum oxides induced phase separation in the borosilicate glass, which lead to an increase in liquidus temperature and viscosity and to a decrease in oxygen diffusivity and of boria evaporation from the glass. All tantalum silicide-containing compositions demonstrated phase separation in the borosilicate glass and higher oxidation resistance than pure ZrB₂, with the effect increasing with temperature. The most oxidation-resistant ceramics contained 15 vol% Ta₅Si₃, 30 vol% TaSi₂, 35 vol% Si₃N₄, or 20 vol% Si₃N₄ with 10 mol% CrB₂. These materials exceeded the oxidation resistance of the ZrB₂/SiC ceramics below 1300°–1400°C. However, the ZrB₂/SiC ceramics showed slightly superior oxidation resistance at 1500°C.     

Phase Equilibria in the Systems NiO-Cr2,O3,-O2, MgO-Cr2O3−O2, and CdO-Cr2,O3,-O2, at High Oxygen Pressures

Phase equilibria were determined for the systems NiO-Cr₂O₃−O₂, MgO-Cr₂O₃,-O₂, and CdO-Cr₂O₃−O₂ from 450° to above 850° C and at oxygen pressures of from 2 to 3500 atm. Only two intermediate phases were found in the nickel system: NiCrO., (CrVO₄ structure) and the spinel NiCr₂O₄. The magnesium and cadmium systems are similar in that they have three analogous phases: the low-temperature α-MgCrO₄ and α-CdCrO₄ (both with the CrVO₄ structure), the high-temperature β-MgCrO₄ and β-CdCrO₄ (both with the α-MnMoO₄ structure), and the spinels MgCr₂O₄ and CdCr₂O₄. The cadmium system contains an additional phase, Cd₂CrO₅, which is primitive monoclinic.