Synthesis of 3,3′-Bis(2,2′,4,4′,6,6′-Hexanitortilbene)

This paper describes the synthesis of 3,3′bis(2,2′,4,4′,6,6′-hexanitrostilbene) (5). Based on the Ullmann reaction we prepared the title compound in nitrobenzene by using 3-chloro 2,2′,4,4′,6,6′-hexanitroztilbene (4) as the starting material and copper powder as the catalyst. (4) was reacted with hydrazine, not to yield a desired product, azo-3,3′bist(2,2′,4,4′,6,6′-hexanitrostilbene.) but to form a well-known explosive, 2,2′,4,4′,6,6′-hexanitrostibene (6). Differential scanning calorimetrical analysis has shown that (5) begins to decompose at the temperature of 298°C.     

Studies on the Synthesis of 2,2′,4,4′,6,6′-Hexanitrostilbene

The synthesis of 2,2′,4,4′,6,6′-hexanitrostilbene by oxidative coupling of 2,4,6-trinitrotoluene in the presence of metal catalysts has been studied. The effects of reaction parameters on product yields have been evaluated and mechanisms for the reaction are proposed.     

A Parametric Study of the Synthesis of 2,2′,4,4′,6,6′-Hexanitrostilbene from trinitrotoluene and sodium hypochlorite

The synthesis of 2,2′,4,4′,6,6′-hexanitrostilbene by the action of alkaline sodium hypochlorite on 2,4,6-trinitrotoluene has been studied. The effects of time, temperature, pH, solvent composition and mode of TNT addition on the yield of HNS are discussed. The reaction, usually referred to as the Shipp synthesis, is shown to be highly susceptible to variations in process conditions, particularly base and water concentrations. The conversion of 2,4,6-trinitrobenzyl chloride, an intermediate in the Shipp reaction, to HNS has also been examined.     

Crystallography and Structure–Property Relationships of 2,2″,4,4′,4″,6,6′,6″‐Octanitro‐1,1′ : 3′,1″‐Terphenyl (ONT)

An X‐ray crystallographic study of 2,2″,4,4′,4″,6,6′,6″‐octanitro‐1,1′ : 3′,1″‐terphenyl (ONT) has been carried out. The dihedral angles between benzene rings vary from 84.9° to 89.4°. Nonbinding interatomic distances of oxygen atoms inside all the nitro groups are shorter than the intermolecular contact radii for oxygen. On the basis of the DFT B3LYP/6‐31(d, p) method it was found that the difference between the X‐ray structure in the solid phase and DFT result for the gas phase is 98 kJ mol⁻¹, and the bearer of the highest initiation reactivity of the ONT molecule in the solid phase should be the nitro group at 4″‐position, in contrast to those at 4′‐ or 6′‐position that play this role in the isolated molecule. It has been stated that the nitro groups at the reaction centers of the ONT molecule are relatively well specified by their ¹⁵N NMR chemical shifts.     

Synthesis and Energetic Properties of 4,4′,5,5′‐Tetranitro‐2,2′‐biimidazolate(N4BIM) Salts

This paper describes the synthesis and characterization of several salts of 4,4′,5,5′‐tetranitro‐2,2′‐biimidazolate (N4BIM). Each of the salts were characterized chemically, thermally, morphologically, as well as with respect to destructive stimuli (impact, electrostatic discharge, friction, thermal). These salts show promise as propellant ingredient additives, and in particular, the bis‐triaminoguanidinium salt of N4BIM displays excellent burn rate and combustion behavior. Our combustion studies have shown that TAGN4BIM displays a fast burning rate and has the lowest pressure dependence exponent yet measured for a triaminoguanidinium salt.     

Bishydrazinium and Diammonium Salts of 4,4′,5,5′‐Tetranitro‐2,2′‐biimidazolate (TNBI): Synthesis and Properties

The diammonium ( 1 ) and bishydrazinium ( 2 ) salts of 4,4′,5,5′‐tetranitro‐2,2′‐biimidazolate (TNBI) were synthesized and their physical properties as well as predicted explosive performance characteristics are described. These dianionic salts are easily formed in good yields by reaction of TNBI with aqueous solutions of the cationic species. TNBI is synthesized from 2,2′‐biimidazole, which is ultimately synthesized by the condensation of aqueous glyoxal with ammonium acetate. The compounds were characterized by NMR spectroscopy, vibrational (FT‐IR and Raman) spectroscopy, elemental analysis, thermal analysis (DSC, VTS and calorimetry), and small scale safety testing (impact, friction, ESD). The measured densities and heats of formation are reported. The materials show promise for use in IM explosive and propellant formulations due to the combination of their calculated performances, thermal stability and insensitivity to stimuli.     

Crystallography and Structure–Property Relationships in 2,2′,2″,2′′′,4,4′,4″,4′′′,6,6′,6″,6′′′‐Dodecanitro‐1,1′ : 3′1″ : 3″,1′′′‐ Quaterphenyl (DODECA)

X‐ray crystallographic study of 2,2′,2″,2′′′,4,4′,4″,4′′′,6,6′,6″,6′′′‐dodecanitro‐1,1′ : 3′1″ : 3″,1′′′‐quaterphenyl (DODECA) has been carried out. Nonbonding interatomic distances of oxygen atoms inside of all the nitro groups are shorter than those corresponding to the intermolecular contact radii for oxygen. By means of the DFT B3LYP/6‐31(d, p) method a difference of 136 kJ mol⁻¹ between the X‐ray and DFT structures of DODECA was found. The bearer of the highest initiation reactivity in its molecule in solid phase should be the nitro group at 4′′′‐position, in contrast to those at 2′‐ or 2″‐positions in its isolated molecule. The most reactive nitro group in the DODECA molecule can be well specified by the relationship between net charges on nitro groups and charges on their nitrogen atoms, both of them for the X‐ray structure. The ¹⁵N chemical shift, corresponding to this nitro group for the initiation by impact and shock, correlates very well with these shifts of the reaction centers of the other six “genuine” polynitro arenes.     

Synthesis and Characterization of 4,4′,5,5′‐Tetranitro‐2,2′‐Bi‐1H‐imidazole (TNBI)

We synthesized 4,4′,5,5′‐tetranitro‐2,2′‐bi‐1H‐imidazole (TNBI), which may serve as a new energetic filler for high explosive formulations. TNBI was synthesized by treating an excess amount of sodium nitrate with 2,2′‐bi‐1H‐imidazole (BI), which was produced from glyoxal and ammonia gas. The overall synthetic yield was 32%. The synthesized TNBI was characterized by performing various chemical analyses including NMR, IR, and CHN analyses. Small scale sensitivity tests were carried out at both research institutes (ADD and ARDEC). The sensitivity results varied from ‘more sensitive than RDX’ to ‘substantially less sensitive than RDX’ according to the purity and conditions of the test samples. Based on our careful characterizations, this large variation in sensitivity was attributed to the moisture content that was present in the test samples due to a hygroscopic nature of TNBI. We also found that the hygroscopic nature of TNBI changed significantly due to the amount of impurities, especially sulfates.     

Synthesis and properties of organosoluble polyimides derived from 2,2′‐dibromo‐ and 2,2′,6,6′‐tetrabromo‐4,4′‐oxydianilines

Two new aromatic diamines, 2,2′‐dibromo‐4,4′‐oxydianiline (DB‐ODA 4 ) and 2,2′,6,6′‐tetrabromo‐4,4′‐oxydianiline (TB‐ODA 5 ), have been synthesized by oxidation, bromination, and reduction of 4,4′‐oxydianiline (4,4′‐ODA). Novel polyimides 6a–f and 7a–f were prepared by reacting DB‐ODA ( 4 ) and TB‐ODA ( 5 ) with several dianhydrides by one‐step method, respectively. The inherent viscosities of these polyimides ranged from 0.31 to 0.99 dL/g (0.5 g/dL, in NMP at 30°C). These polyimides showed enhanced solubilities compared to those derived from 4,4′‐oxydianiline and corresponding dianhydrides. Especially, polyimides 7a , derived from rigid PMDA and TB‐ODA ( 5 ) can also be soluble in THF, DMF, DMAc, DMSO, and NMP. These polyimides also exhibited good thermal stability. Their glass transition temperatures measured by thermal mechanical analysis (TMA) ranged from 251 to 328°C. When the same dianhydrides were used, polyimides 7 containing four bromide substituents had higher glass transition temperatures than polyimides 6 containing two bromide substituents. The effects of incorporating more polarizable bromides on the refractive indices of polyimides were also investigated. The average refractive indices (n_av) measured at 633 nm were from 1.6088 to 1.7072, and the in‐plane/out‐of‐plane birefringences (Δn) were from 0.0098 to 0.0445. It was found that the refractive indices are slightly higher when polyimides contain more bromides. However, this effect is not very obvious. It might be due to loose chain packing resulted from bromide substituents at the 2,2′ and 2,2′,6,6′ positions of the oxydiphenylene moieties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A Parametric Study of the Synthesis of 4,4′,5,5′,7,7′-Hexanitro-1,1′-Binaphthyl

Conditions for the synthesis of 4,4′,5,5′,7,7′-hexanitrobinaphthyl( I ) from 1,1′-binaphthyl have been investigated. It has been found that( I ) can be prepared in 50% yield in a two-stage nitration process.     

Combustion Properties of Amino‐Substituted Guanidinium 4,4′,5,5′‐Tetranitro‐2,2′‐biimidazolate(N4BIM) Salts

This paper describes the combustion properties of the amino‐substituted guanidinium 4,4′,5,5′‐tetranitro‐2,2′‐biimidazolate (N4BIM) series, including the bis‐mono, di and triaminoguanidinium salts. These salts are of interest as propellant ingredient additives, and in particular, the bis‐triaminoguanidinium salt of N4BIM displays excellent burn rate and combustion behavior. Our combustion studies have shown that TAGN4‐BIM displays a fast burning rate and has the lowest pressure dependence exponent yet measured for a triaminoguanidinium salt.     

Morphology of polyimide fibers derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 4,4′‐oxydianiline

As one member of high performance fibers, aromatic polyimide fibers possess many advantages, such as high strength, high modulus, high and low temperature resistance, and radiation resistance. However, the preparation of the high performance fibers is so difficult that the commercial fibers have not been produced except P84 with good flame retardancy. In this report, a polyimide was synthesized from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐oxydianiline (ODA) and the fibers were prepared from its solution by a dry‐jet wet‐spinning process. The formation of the as‐spun fibers in different coagulation bath composition was discussed. Scanning electron microscope (SEM) was employed to study the morphology of the as‐spun fibers. As a result, the remnant solvent existed in the as‐spun fibers generated from coagulation bath of alcohol and water. There were many fibrils and microvoids with the dimension of tens of nanometers in the fibers. One could observe the obvious fibrillation and the drawn fibers. The measurement for the mechanical properties of the fibers with a drawing ratio of 5.5 indicated that tensile strength and initial modulus were 2.4 and 114 GPa, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 669–675, 2004     

Investigation of the action of flame retardants in cellulose. I. Investigation of the flame retardant action of 2,2′-oxybis(5,5-dimethyl-1,3,2-dioxaphosphorinane-2,2′-disulfide) in cellulose

Pyrolysis experiments were performed in high vacuum and under reduced air pressure (100 Pa). The volatile products of pure cellulose and cellulose containing various amounts of flame retardant 2,2′-oxybis (5,5-dimethyl-1,3,2-dioxaphosphorinane-2,2′-disulfide), i.e., Sandoflam 5060 of Sandoz AG, were studied by means of gas chromatography in combination with mass spectroscopy. The volatile products were characterized with infrared spectroscopy. The studied revealed that the incorporation of the flame retardant enhanced the water release and shifted the onset of this reaction to lower temperature. On the basis of these findings an explanation for the mechanism of flame retardancy in generated cellulose fibers modified with this particular flame retardant is attempted. From experiments with different residual air pressure the influence of oxygen on the primary processes of the pyrolytic degradation of cellulose is being discussed.     

Synthesis and properties of new aromatic polyimides based on 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride

New polyimides with enhanced thermal stability and high solubility were synthesized in common organic solvents from a new dianhydride, 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride (DBBTDA). DBBTDA was used as monomer to synthesize polyimides by using various aromatic diamines. The polymers were characterized by IR and NMR spectroscopy and elemental analysis. These polyimides had good inherent viscosities in N‐methyl‐2‐pyrrolidinone (NMP) and also high solubility and excellent thermo‐oxidative stability, with 5 % weight loss in the range 433 to 597 °C. Copyright © 2004 Society of Chemical Industry     

Copolymers of 3,3′,4,4′-tetraaminobiphenyl and 1,2,4,5-tetraaminobenzene with 1,1′-bis(glyoxalyl)-ferrocene and 1,1′-bis(phenylglyoxalyl)ferrocene

Four monomers were synthesized and four copolymers prepared. The polymers were dark-colored, poorly soluble, crystalline products. The x-ray photographs were typical of triclinic crystals. The polymers degraded at temperatures lower than those characteristic of the analogous homopolymers. The recovered polymers were ferromagnetic.     

Preparation and properties of novel fluorinated polyimides based on 2,2′,6,6′-tetrafluorobenzidine

Fluorinated polyimides were prepared from 2,2′,6,6′-tetrafluorobenzidine and four conventional dianhydride monomers by a solution polycondensation reaction followed by a chemical imidization. Polyimide based on 2,2′,6,6′-tetrafluorobenzidine and hexafluoroisopropylidene bis(3,4-phthalic anhydride) (6FDA) is soluble in organic solvents such as NMP, DMA, DMF, THF, chloroform, and acetone while those based on 2,2′,6,6′-tetrafluorobenzidine and pyromellitic dianhydride (PMDA), benzophenone-3,3′,4,4′-tetracarboxylic acid dianhydride (BTDA), diphenylether-3,3′,4,4′-tetracarboxylic acid dianhydride (ETDA) are not. Polyimide from 2,2′,6,6′-tetrafluorobenzidine and 6FDA possesses high optical transparency at 350–700 nm and has a in-plane refractive index of 1.558 at 632.8 nm. All polyimides exhibit glass transition temperatures above 350°C. They also possess very high thermal stability. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1605–1609, 1998     

Reaction kinetics and thermal properties of epoxidised cresol novolac/4,4′‐diglycidyl (3,3′,5,5′‐tetramethylbiphenyl) epoxy resin composite cured with aromatic diamine

A series of novel composites based on different ratios of epoxidised cresol novolac (ECN) and 4,4′‐diglycidyl(3,3′,5,5′‐tetramethylbiphenyl) epoxy resin (TMBP) have been prepared with the curing agent 4,4′‐methylenediamine (DDM) and 4,4′‐diaminodiphenylsulfone (DDS), respectively. The investigation of cure kinetics was performed by differential scanning calorimetry using an isoconversional method. The high thermal stabilities of the cured samples were also studied by thermogravimetric analysis. In addition, no phase separation was observed for cured ECN/DDM and ECN/DDS blending with different amounts of TMBP by dynamic mechanical analysis and scanning electron microscopy. Moreover, the cured systems also exhibited excellent impact properties and low moisture absorption. All the results indicate that the ECN/TMBP/DDM and ECN/TMBP/DDS systems are promising materials in electronic packaging. Copyright © 2011 Society of Chemical Industry     

Theoretical Studies on Molecular and Explosive Properties of 4,4′,5,5′‐Tetranitro‐2,2′‐bi‐1H‐imidazole (TNBI)

We performed theoretical studies to predict the molecular structure, molecular properties, and explosive performance of 4,4′,5,5′‐tetranitro‐2,2′‐bi‐1H‐imidazole (TNBI). High levels of ab initio and density functional theories were employed to predict the molecular structure of TNBI. Predicted TNBI structure was in good agreement with that observed by X‐ray crystallography. Heat of formation in the solid phase at 298 K was predicted to be 270.3 kJ/mol. Density of TNBI was predicted to be 1.919–1.956 g/cm³ depending upon the parameter sets of group additivity method. By using these values as input data, we estimated detonation velocity and C–J pressure to be 8.69–8.80 km/s and 34.5‐36.1 GPa, respectively. Impact sensitivity of TNBI was predicted to be 33 cm.     

Synthesis and characterization of organosoluble polyfluorinated polyimides derived from 3,3′,5,5′‐tetrafluoro‐4,4′‐diaminodiphenylmethane and various aromatic dianhydrides

A polyfluorinated aromatic diamine, 3,3′, 5,5′‐tetrafluoro‐4,4′‐diaminodiphenylmethane (TFDAM), was synthesized and characterized. A series of polyimides, PI‐1–PI‐4, were prepared by reacting the diamine with four aromatic dianhydrides via a one‐step high‐temperature polycondensation procedure. The obtained polyimide resin had moderate inherent viscosity (0.56–0.68 dL/g) and excellent solubility in common organic solvents. The polyimide films exhibited good thermal stability, with an initial thermal decomposition temperature of 555°C–621°C, a 10% weight loss temperature of 560°C–636°C, and a glass‐transition temperature of 280°C–326°C. Flexible and tough polyimide films showed good tensile properties, with tensile strength of 121–138 MPa, elongation at break of 9%–12%, and tensile modulus of 2.2–2.9 GPa. The polyimide films were good dielectric materials, and surface and volume resistance were on the order of a magnitude of 10¹⁴ and 10¹⁵ Ω cm, respectively. The dielectric constant of the films was below 3.0 at 1 MHz. The polyfluorinated films showed good transparency in the visible‐light region, with a cutoff wavelength as low as 302 nm and transmittance higher than 70% at 450 nm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1442–1449, 2007     

Preparation and characterization of 3,3′,4,4′-benzophenone tetracarboxylic dianhydride-pyromellitic diahydride alternating polyimides

Four kinds of 3,3′,4,4′-benzophenone tetracarboxylic dianhydride (BTDA)-pyromelliitic dianhydride (PMDA) alternating polyimide (BTDA-PMDA API) were obtained by reacting 1 mol BTDA with 2 mol diamines to form BTDA chain-extended diamines (BTDA CED), followed by the addition of 1 mol PMDA to yield the BTDA-PMDA alternating polyamic acids (BTDA-PMDA APA), and finally by imidizing them thermally. BTDA CED were characterized by elemental analysis, infrared (IR), and ¹H-NMR spectroscopy. The structures of BTDA-PMDA APA and BTDA-PMDA API were investigated by IR and ¹H-NMR spectroscopy, and their thermal properties and interfacial tension were also studied. Furthermore, the characteristic properties of BTDA-PMDA API were compared with their corresponding homopolyimides from BTDA (BTDA HPI) and from PMDA (PMDA HPI). It was found that the alternating condensation polymerization is an effective method to modify polyimides interfacial tension with a small influence on the thermal stability. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 1585–1593, 1997