Impedimetric immobilized DNA-based sensor for simultaneous detection of Pb2+, Ag+, and Hg2+

An unlabeled immobilized DNA-based sensor was reported for simultaneous detection of Pb(2+), Ag(+), and Hg(2+) by electrochemical impedance spectroscopy (EIS) with [Fe(CN)(6)](4-/3-) as redox probe, which consisted of three interaction sections: Pb(2+) interaction with G-rich DNA strands to form G-quadruplex, Ag(+) interaction with C-C mismatch to form C-Ag(+)-C complex, and Hg(2+) interaction with T-T mismatch to form T-Hg(2+)-T complex. Circular dichroism (CD) and UV-vis spectra indicated that the interactions between DNA and Pb(2+), Ag(+), or Hg(2+) occurred. Upon DNA interaction with Pb(2+), Ag(+), and Hg(2+), respectively, a decreased charge transfer resistance (R(CT)) was obtained. Taking advantage of the R(CT) difference (ΔR(CT)), Pb(2+), Ag(+), and Hg(2+) were selectively detected with the detection limit of 10 pM, 10 nM, and 0.1 nM, respectively. To simultaneously (or parallel) detect the three metal ions coexisting in a sample, EDTA was applied to mask Pb(2+) and Hg(2+) for detecting Ag(+); cysteine was applied to mask Ag(+) and Hg(2+) for detecting Pb(2+), and the mixture of G-rich and C-rich DNA strands were applied to mask Pb(2+) and Ag(+) for detecting Hg(2+). Finally, the simple and cost-effective sensor could be successfully applied for simultaneously detecting Pb(2+), Ag(+), and Hg(2+) in calf serum and lake water.     

A new Schiff's base ligand immobilized agarose membrane optical sensor for selective monitoring of mercury ion

A highly selective optical sensor was developed for the Hg(2+) determination by chemical immobilization of 2-[(2-sulfanylphenyl)ethanimidoyl]phenol (L), on an agarose membrane. Spectrophotometric studies of complex formation between the Schiff's base ligand L and Hg(2+), Sr(2+), Mn(2+), Cu(2+), Al(3+), Cd(2+), Zn(2+), Co(2+) and Ag(+) metal ions in methanol solution indicated a substantially larger stability constant for the mercury ion complex. Consequently, the Schiff's base L was used as an appropriate ionophore for the preparation of a selective Hg(2+) optical sensor, by its immobilization on a transparent agarose film. A distinct color change, from yellow to green-blue, was observed by contacting the sensing membrane with Hg(2+) ions at pH 4.5. The effects of pH, ionophore concentration, ionic strength and reaction time on the immobilization of L were studied. A linear relationship was observed between the membrane absorbance at 650 nm and Hg(2+) concentrations in a range from 1×10(-2) to 1×10(-5) mol L(-1) with a detection limit (3σ) of 1×10(-6) mol L(-1). No significant interference from 100 times concentrations of a number of potentially interfering ions was detected for the mercury ion determination. The optical sensor was successfully applied to the determination of mercury in amalgam alloy and spiked water samples.     

Antimony film electrode for electrochemical stripping analysis

In this work, an antimony film electrode (SbFE) is reported for the first time as a possible alternative for electrochemical stripping analysis of trace heavy metals. The SbFE was prepared in situ on a glassy carbon substrate electrode and employed in combination with either anodic stripping voltammetry or stripping chronopotentiometry in nondeaerated solutions of 0.01 M hydrochloric acid (pH 2). Several key operational parameters influencing the electroanalytical response of SbFE were examined and optimized, such as deposition potential, deposition time, and composition of the measurement solution. The SbFE exhibited well-defined and separated stripping signals for both model metal ions, Cd(II) and Pb(II), surrounded with low background contribution and a relatively large negative potential range. The electrode revealed good linear behavior in the examined concentration range from 20 to 140 microg L-1 for both test metal ions, with a limit of detection (3sigma) of 0.7 microg L-1 for Cd(II) and 0.9 microg L-1 for Pb(II) obtained after a 120 s deposition step, and good reproducibility, with a relative standard deviation (RSD) of +/-3.6% for Cd(II) and +/-6.2% for Pb(II) (60 microg L-1, n = 12). When comparing the SbFE with the commonly used mercury film electrode and recently introduced bismuth film electrode, the newly proposed electrode offers a remarkable performance in more acidic solutions (pH < or = 2), which can be advantageous in electrochemical analysis of trace heavy metals, hence contributing to the wider applicability of electrochemical stripping techniques in connection with "mercury-free" electrodes.     

钎焊散热器用钎料的成份改进及性能

本文根据金属学原理及钎焊润湿性原理，以铅－锡钎料为基，以降低钎料熔点和增加其润湿性为目的，以Ａｇ、Ｈｇ、Ｃｄ、Ｓｂ、Ｂｉ为改善钎料工艺性能的添加元素，通过正交试验，提出了一种含锡量为１４％的新材料。这种新材料的工艺性能可与含锡４０％的铅－锡钎料相媲美。     

Mercuric ion sensing by a film bulk acoustic resonator

This paper describes a film bulk acoustic resonator (FBAR) mass sensor for detecting Hg2+ ion in water with excellent sensitivity and selectivity. When a thin Au film was deposited on the surface of an FBAR, the resonant frequency shifted to a lower value when the film was exposed to Hg2+ in aqueous solution. The FBAR sensor detected as low as 10(-9) M Hg2+ (0.2 ppb Hg2+) in water. Other ions such as K+, Ca2+, Mg2+, Zn2+, and Ni2+ had little or no effect on the resonant frequency of the FBAR. Coating of the FBAR Au surface with a self-assembled monolayer (SAM) of 4-mercaptobenzoic acid decreased the Hg2+ response.     

β-Galactosidase-based colorimetric paper sensor for determination of heavy metals

We demonstrate a novel approach for rapid, selective, and sensitive detection of heavy metals using a solid-phase bioactive lab-on-paper sensor that is inkjet printed with sol-gel entrapped reagents to allow colorimetric visualization of the enzymatic activity of β-galactosidase (B-GAL). The bioactive paper assay is able to detect a range of heavy metals, either alone or as mixtures, in as little as 10 min, with detection limits as follows: Hg(II) = 0.001 ppm; Ag(I) = 0.002 ppm, Cu(II) = 0.020 ppm; Cd(II) = 0.020 ppm; Pb(II) = 0.140 ppm; Cr(VI) = 0.150 ppm; Ni(II) = 0.230 ppm. The paper-based assay was immune to interferences from nontoxic metal ions such as Na(+) or K(+), could be used to detect heavy metals that were spiked into tap water or lake water, and provided quantitative data that was in agreement with values obtained by atomic absorption. With the incorporation of standard chromogenic metal sensing reagents into a multiplexed bioactive paper sensor, it was possible to identify specific metals in mixtures, albeit with much lower detection limits than were obtained with the enzymatic assay. The paper-based sensor should be valuable for rapid, on-site screening of trace levels of heavy metals in resource limited areas and developing countries.     

Purification of cadmium up to 5N+ by vacuum distillation

Cadmium was refined by vacuum distillation, a technique suitable for low boiling and melting point materials, to remove the heavy and low vapour pressure impurities at ppm level. The detailed analysis of the purified Cd as well as raw Cd was done by ICP-OES techniques for 27 impurity elements. Purification was carried out in an efficient high-yield vacuum distillation system designed and fabricated for purifying 3N+ purity indigenous cadmium to 5N+ (99.999%). Analysis confirmed the reduction of total impurity content from 134 ppm (3N7) for raw Cd to 3 ppm (5N7) upon vacuum distilled Cd. The present study shows that the analysis of impurities such as Fe, Mg and Ca are contributed from environmental effect, whereas impurities such as Pb, Bi, Ag, Ni, Cu, Zn and Tl require adaptation of elemental analysing technique to counter dilution effect. The Hg trace analysis can however be carried out by hydride generation techniques.     

Standard Cells with Cd?Pb Amalgam Electrode

In order to improve the characteristics of standard cells, those containing composite amalgam electrode have been studied. The criterion and test procedures established for selecting high-quality standard cells have been applied. The addition of Pb to Cd amalgam has the effect of reducing the temperature coefficient. The most appropriate composition of amalgam is that of 10 wt % Cd, 3-9 wt % Pb, and the balance Hg. The cells with Cd-Pb amalgam electrode have an EMF higher by about 1000 ?V than that of normal Weston cell, and a temperature coefficient at 20° C or -17 ?V/°C. The other characteristics and stability are the same as those of normal cells and they are suitable for high-precision work. Although zero temperature coefficient may be obtained by adding Pb and Bi to Cd amalgam, its characteristics are inferior to those of normal cells.     

Lead (II) ion detection in surface water with pM sensitivity using aza-crown-ether-modified silver nanoparticles via dynamic light scattering

In this paper, we reported ultrasensitive lead ion detection in environmental water with pM sensitivity using aza-crown-ether-modified silver nanoparticles (ACE-Ag NPs) through dynamic light scattering (DLS). The colorimetric method based on ACE-Ag NPs is not capable of detecting Pb2+ ions over other metal ions (Fe3+, Co2+, Cu2+, Hg2+, Cd2+, Ag+, Li+, Na+, K+ and Cs+) with high sensitivity. But DLS has improved the selectivity and sensitivity of the Pb2+ detection system (50-fold or more) over colorimetric method, and its detection limit is 0.25 pM (1.03 ppt). The Pb2+ DLS assay can be applied to detect Pb2+ in the environmental water, such as in Yangtze and East Lake water samples with a detection limit of 0.20 and 0.22 pM, which is much lower than the maximum contamination level of 4.8×10(-8) M for lead in surface water defined by the national environmental quality standards of China (GB 3838-2002). Also, this method has a good performance in the determination of Pb2+ in drinking water, which is much lower than the maximum contamination level (MCL) of 72 nM for lead as defined by the US Environmental Protection Agency (EPA).     

Sample preconcentration using ion-exchange polymer film for laser ablation sampling inductively coupled plasma atomic emission spectrometry

An efficient sample pretreatment/introduction technique for the inductively coupled plasma atomic emission spectrometry (ICP-AES) using ion exchange for analyte preconcentration and matrix separation and laser ablation sampling for sample introduction has been developed. Ammonium pyrrolidine dithiocarbamate (APDC)-polystyrene films are coated on glass plates for analyte preconcentration. Repetitive laser ablation sampling of the polymer film removes the ion-exchanged metal ions from the polymer film as fine particles for sample introduction into the ICP. After immersing the sample probe in a sample solution for 5 min, the ICP emission intensity for laser ablation of the polymer film is a few times larger than that after solution nebulization. The sample probe removes only a small fraction of the sample solution and, therefore, in principle, does not disturb the original solution significantly. Single-pulse laser ablation of the polymer film shows that the ion-exchanged metal ion concentration in the film reduces exponentially with the depth of the polymer film. Ion exchange to the polymer film is probably limited by the rate of metal ion diffusion into the film. Calibration curves for Cu, Hg, Pb, and Zn show linear dynamic range of ～1-2 orders of magnitude. The linear dynamic range for Cu increases to >3 orders of magnitude when using Pb as an internal standard. RSD of the ICP emission intensity is ～8%.     

Bi(III)4-methylpiperidinedithiocarbamate coprecipitation procedure for separation--pre-concentration of trace metal ions in water samples by flame atomic absorption spectrometric determination

A pre-concentration method was developed for determination of trace amounts of cadmium, copper and lead in water samples by FAAS after coprecipitation by using potassium 4-methylpiperidinedithiocarbamate (K4-MPDC) as a chelating agent and Bi(III) as a carrier element. This procedure is based on filtration of the solution containing precipitate on a cellulose nitrate membrane filter following Cd(II), Cu(II) and Pb(II) coprecipitation with Bi(III)4-MPDC and then the precipitates together with membrane filter were dissolved in concentrated nitric acid. The metal contents of the final solution were determined by FAAS. Several parameters including pH of sample solution, amount of carrier element and reagent, standing time, sample volume for precipitation and the effects of diverse ions were examined. The accuracy of the method was tested with standard reference material (MBH, C31XB20 and CRM BCR-32) and Cd, Cu and Pb added samples. Determination of Cd, Cu and Pb was carried out in sea water, river water and tap water samples. The recoveries were >95%. The relative standard deviations of determination were less than 10%.     

Improvement in the Adhesion Between Electrode of a SOFC and Ag Paste as a Current Collector by Au Deposition

This paper reports the use of Au films to improve the performance of the stacked solid oxide fuel cell(SOFC) based on the characterization of the interface and the adhesion between the electrodes of the SOFCs and the Ag paste. The specimens were manufactured to perform the experiment as follows. A Si O2 wafer with a 300 mm notch was attached to the electrodes of a SOFC by a Ag paste and Au film, which were deposited on the electrodes by sputtering for 1 min or 5 min deposition time and annealed at300 C for 1 h. The four-point bending test was performed, which resulted in the formation of an extended crack at the tip on the wafer notch, and the crack propagation was observed using a stereo microscope equipped with a charge-coupled device(CCD). Consequently, the interfacial adhesion energy and the effect of the Au film between the each electrode and the Ag paste can be evaluated. On the cathode, the interfacial adhesion energy without Au film was 2.59 J/m2(upper value) and the adhesion energy increased to 11.59 J/m2(upper value) and 15.89 J/m2(lower value) with the Au film. On the anode,the interfacial adhesion energy without Au film was 1.74 J/m2(upper value), which increased to 11.07 J/m2(upper value) and 14.74 J/m2(lower value) with the Au film. In addition, the interface areas were analyzed by scanning electron microscopy(SEM) and energy dispersive spectroscopy(EDS) to estimate the interface delamination.     

Voltammetric sensor for general purpose organohalide detection at picogram per liter concentrations based on a simple collector-generator method

With the aim of producing a general purpose sensor for environmental analysis, we describe a simple and sensitive method for organohalide detection, based on an electrochemical collector-generator process. The sensor consists of four coplanar electrodes contacting a solution volume of 300 microL, containing organohalide. At the first working electrode (a Zn/PTFE composite), the analyte is electrolyzed to liberate halide ions. At the second working electrode (Ag), the halide ions are detected by cathodic stripping voltammetry. Using a preconcentration time of 600 s, with differential pulse voltammetry for stripping, the responses to 1-chloropropane, chloroform, carbon tetrachloride, iodoethane, and bromoethane can be plotted on a common calibration curve, with a detection limit of 0.1 nM (1.3 pg L(-1) or less depending on the organohalide). To the best of our knowledge, this is the lowest reported organohalide detection limit by an electrochemical method and is so far the only general purpose electrochemical method sensitive enough for regulatory requirements. The sensor response was invariant for approximately 40 measurements. Analysis of tap water, spiked with chloroform or carbon tetrachloride, gave recoveries within 1.0-2.6% of the recoveries by the standard GC method.     

Sensitive and selective detection of mercury (II) based on the aggregation of gold nanoparticles stabilized by riboflavin

Gold nanoparticles (AuNPs) can be stabilized by riboflavin against tris buffer-induced aggregation. However, in the presence of mercury (II) (Hg2+), riboflavin can be released from the AuNPs surface and the riboflavin-Hg2+ complex formed, leading to the aggregation of AuNPs in tris buffer. The aggregation extent depends on the concentration of Hg2+. Based on the aggregation extent, a simple and sensitive method of determining Hg2+ is developed. The method enables the detection of Hg2+ over the concentration range of 0.02-0.8 microM, with a detection limit (3sigma) of 14 nM, and shows excellent selectivity for Hg2+ over other metal ions (Cu2+, Co2+, Cd2+, Pb2+, Mg2+, Zn2+, Ag+, Ce3+, Ca2+, Al3+, K+). More importantly, the method avoids complicated surface modifications and tedious separation processes.     

ICP-AES法测定金箔的含金量

研究了ICP-AES法直接测定金箔中的Ag、Cu、Zn、Fe、Pb、Sb、Bi微量元素,通过差减法计算出金箔的含金量,确定了仪器最佳工作参数,研究了分析条件中功率的选取、分析线的选择、雾化器压力的优化、样品提升量的影响,并对金箔中Au基体可能存在的干扰等进行了探讨。所建立的分析方法精密度、准确度符合微量分析的要求,用于金箔样品分析,准确、快速、简便,结果满意。     

Synthesis of polyimide from 5,5'-bis(bromomethyl)-2,2':6',2'-terpyridine and investigation of the polymer sorption behavior towards some metal ions

The synthesis of a terpyridine-based polyimide sorbent for solid-phase extraction (SPE) of some metal ions is described. For this purpose, 5,5'-bis(bromomethyl)-2,2':6',2'-terpyridine was polymerized with the corresponding diimide derivatives of dianhyrides to give polyimides utilizing terpyridine unit in the main chain. This polymer was used for its extraction capabilities for Pb(II), Ni(II), Cu(II), Zn(II), Cd(II) and Hg(II), at different pH. Under competitive conditions and at pH<0.6, the selectivity order was Pb approximately Cd approximately Zn. Enhanced selectivity was observed at pH 3.5, the order was Cu>Ni>Zn approximately Cd approximately Pb. Quantitative recoveries>97% were observed for all metals in case loading was stopped before reaching the point of breakthrough. As the synthesized polyimides are insoluble in water, solid-liquid extractions have been carried out and the resins sorption for mixture of basic and/or precious metals have been studied under various experimental conditions (reaction time and hydrochloric acid concentration).     

Simultaneous multi-element detection of metal ions bound to a Datura innoxia material

An on-line detection scheme has been developed for the determination of metal ion affinities for binding to a plant-based substrate. This involves monitoring the effluent of a column packed with cell-wall fragments from the plant Datura innoxia for 27 different elements simultaneously by coupling the column to an ICP emission spectrometer. Previously accepted procedures for removing native metal ions from biological materials by washing the material with a pH 2 solution were found to be insufficient for this material. Measurable amounts of Na, Mg, Al, Ca, Mn, Fe, Ni, Cr, Zn, Cd, Pb, Ba, Sr, and Si were all detected in an effluent from the introduction of 1.0M HCl following washing the material in a pH 2 solution. Metal ion breakthrough curves for Cd(2+), Zn(2+), Ni(2+), Cu(2+), and Pb(2+) were found to exhibit an affinity order of Pb(2+)>Cu(2+)>Zn(2+) congruent with Cd(2+)>Ni(2+) for an equimolar mixture of these metal ions. This configuration also enabled the displacement of metal ions to be detected as the breakthrough curve for a subsequent metal ion was monitored. Comparison of Ni and Zn binding indicates a simple ion exchange model is insufficient to explain sequential binding of these metal ions.     

Microstructures formed from mixed solders on copper substrate

Abstract

With the development and use of a variety of Pb free solders, it is probable that some solder joints in electronic assemblies may be made with solders of two different compositions. To investigate possible microstructures resulting from such procedure, samples were prepared using small balls of four different Sn–Ag–Cu (SAC) Pb free solders, as well as Sn–Zn–Al solder, melted together with eutectic Pb–Sn solder paste and also various SAC solder pastes, on a copper substrate. It was observed that using eutectic Pb–Sn solder paste with an SAC solder ball introduced some Pb–Sn eutectic microstructure and changed the ternary eutectic present from Ag₃Sn–Cu₆Sn₅–Sn to Ag₃Sn–Pb–Sn. Use of an SAC solder paste with Sn–Zn–Al solder introduced an apparent Ag–Cu–Zn ternary compound, replacing Zn lamellae of the Sn–Zn eutectic. With eutectic Pb–Sn solder paste, the Pb–Sn–Zn ternary eutectic was formed. It was noted that use of a high Sn solder results in rapid dissolution of the copper substrate.     

铂、钯材料ICP分析方法的研究

由于铂、钯材料被广泛应用于多种精密行业,其材料含量也越来越受到重视,目前采用的方法不是操作复杂就是范围太窄而不符合日常检测要求,因此急需建立一种简捷快速的、适用于铂、钯材料含量为95．0％-99．99％的化学分析方法。该文用电感耦合等离子发射光谱分析,测定铂、钯材料中铂（钯）、铑、铱、钌、金、银、铜、铁、镍、铝、铅、锰、铬、镁、锡、硅、锌及铋等杂质元素的方法,达到了检出限低、重复性好、回收率在88．3％-100％的检测目标。     

Aqua regia extracted metals in sediments from the industrial area and surroundings of Pančevo, Serbia

Surface and buried sediments were analyzed for Ba, Ca, Cd, Co, Cr, Cu, Mn, Ni, Pb, Zn and V, as well as for total carbon and hydrogen to assess the distribution of sediment pollution due to the vicinity of the petrochemical complex. The samples, collected from 20 locations within the petrochemical complex and from 16 locations outside the complex, were aqua regia extracted and analyzed by ICP/OES. Metals were determined with an acceptable accuracy for certified metals of 82-113%. The precision for the aqua regia extraction was satisfactory, less than 20%, except for Cd where it was 28%. Comparison of the data from the petrochemical with those from the non-petrochemical areas showed different distributions of the metals. Metals that exceeded the baseline range; Ba, Cd, Cu, Zn and Pb, were detected in higher concentrations in sediments that were under the influence of the chlor-alkali plant within the petrochemical complex. Comparison with data from the petrochemical complex and its surroundings and their distribution demonstrated that the metal compositions of the sediments were modified by anthropogenic activities.