A Semitransparent Inorganic Perovskite Film for Overcoming Ultraviolet Light Instability of Organic Solar Cells and Achieving 14.03% Efficiency

Organic solar cells (OSCs) can be unstable under ultraviolet (UV) irradiation. To address this issue and enhance the power conversion efficiency (PCE), an inorganic‐perovskite/organic four‐terminal tandem solar cell (TSC) based on a semitransparent inorganic CsPbBr₃ perovskite solar cell (pero‐SC) as the top cell and an OSC as bottom cell is constructed. The high‐quality CsPbBr₃ photoactive layer of the planar pero‐SC is prepared with a dual‐source vacuum coevaporation method, using stoichiometric precursors of CsBr and PbBr₂ with a low evaporation rate. The resultant opaque planar pero‐SC exhibits an ultrahigh open‐circuit voltage of 1.44 V and the highest reported PCE of 7.78% for a CsPbBr₃‐based planar pero‐SC. Importantly, the devices show no degradation after 120 h UV light illumination. The related semitransparent pero‐SC can almost completely filter UV light and well maintain photovoltaic performance; it additionally shows an extremely high average visible transmittance. When it is used to construct a TSC, the top pero‐SC acting as a UV filter can utilize UV light for photoelectric conversion, avoiding the instability problem of UV light on the bottom OSC that can meet the industrial standards of UV‐light stability for solar cells, and leading to the highest reported PCE of 14.03% for the inorganic‐perovskite/organic TSC.     

Hysteresis‐Free 1D Network Mixed Halide‐Perovskite Semitransparent Solar Cells

The morphology of hybrid organic–inorganic perovskite films is known to strongly affect the performance of perovskite‐based solar cells. CH₃NH₃PbI_3‐xCl_x (MAPbI_3‐xCl_x) films have been previously fabricated with 100% surface coverage in glove boxes. In ambient air, fabrication generally relies on solvent engineering to obtain compact films. In contrast, this work explores the potential of altering the perovskites microstructure for solar cell engineering. This work starts with CH₃NH₃PbI_3‐xCl_x, films with grain morphology carefully controlled by varying the deposition speed during the spin‐coating process to fabricate efficient and partially transparent solar cells. Devices produced with a CH₃NH₃PbI_3‐xCl_x film and a compact thick top gold electrode reach a maximum efficiency of 10.2% but display a large photocurrent hysteresis. As it is demonstrated, the introduction of different concentrations of bromide in the precursor solution addresses the hysteresis issues and turns the film morphology into a partially transparent interconnected network of 1D microstructures. This approach leads to semitransparent solar cells with negligible hysteresis and efficiencies up to 7.2%, while allowing average transmission of 17% across the visible spectrum. This work demonstrates that the optimization of the perovskites composition can mitigate the hysteresis effects commonly attributed to the charge trapping within the perovskite film.     

TiO2 Electron Transport Bilayer for Highly Efficient Planar Perovskite Solar Cell

In planar perovskite solar cells, it is vital to engineer the extraction and recombination of electron–hole pairs at the electron transport layer/perovskite interface for obtaining high performance. This study reports a novel titanium oxide (TiO₂) bilayer with different Fermi energy levels by combing atomic layer deposition and spin‐coating technique. Energy band alignments of TiO₂ bilayer can be modulated by controlling the deposition order of layers. The TiO₂ bilayer based perovskite solar cells are highly efficient in carrier extraction, recombination suppression, and defect passivation, and thus demonstrate champion efficiencies up to 16.5%, presenting almost 50% enhancement compared to the TiO₂ single layer based counterparts. The results suggest that the bilayer with type II band alignment as electron transport layers provides an efficient approach for constructing high‐performance planar perovskite solar cells.     

Indium‐Free Perovskite Solar Cells Enabled by Impermeable Tin‐Oxide Electron Extraction Layers

Corrosive precursors used for the preparation of organic–inorganic hybrid perovskite photoactive layers prevent the application of ultrathin metal layers as semitransparent bottom electrodes in perovskite solar cells (PVSCs). This study introduces tin‐oxide (SnO_x) grown by atomic layer deposition (ALD), whose outstanding permeation barrier properties enable the design of an indium‐tin‐oxide (ITO)‐free semitransparent bottom electrode (SnO_x/Ag or Cu/SnO_x), in which the metal is efficiently protected against corrosion. Simultaneously, SnO_x functions as an electron extraction layer. We unravel the spontaneous formation of a PbI₂ interfacial layer between SnO_x and the CH₃NH₃PbI₃ perovskite. An interface dipole between SnO_x and this PbI₂ layer is found, which depends on the oxidant (water, ozone, or oxygen plasma) used for the ALD growth of SnO_x. An electron extraction barrier between perovskite and PbI₂ is identified, which is the lowest in devices based on SnO_x grown with ozone. The resulting PVSCs are hysteresis‐free with a stable power conversion efficiency (PCE) of 15.3% and a remarkably high open circuit voltage of 1.17 V. The ITO‐free analogues still achieve a high PCE of 11%.     

Efficient Perovskite Solar Cells Fabricated Through CsCl‐Enhanced PbI2 Precursor via Sequential Deposition

The fabrication of high‐quality perovskite film highly relies on chemical composition and the synthesis method of perovskite. So far, sequentially deposited MA_0.03FA_0.97Pb(I_0.97Br_0.03)₃ polycrystalline film is adopted to produce high‐performance perovskite solar cells with record power conversion efficiency (PCE). Fewer grain boundaries and incorporation of inorganic cation (e.g., cesium) would further increase device performance via sequential deposition. Here, cesium chloride (CsCl) is introduced into lead iodide (PbI₂) precursor solution that beneficially modulates the property of PbI₂ film, leading to larger grains with cesium incorporation in the resulting perovskite film. The enlarged crystal grains originate from a slower nucleation process for CsCl‐containing PbI₂ film when reacting with formamidine iodide, confirmed by in situ confocal photoluminescence imaging. Photovoltaic devices based on CsCl‐containing PbI₂ film demonstrate a higher averaging efficiency of 21.3% than 20.3% of the devices without CsCl additives for reverse scan. More importantly, the device stability is improved by CsCl additives that retain over 90% of their initial PCE value after 4000 min tracking at maximum power point under 1‐sun illumination. This work paves a way to further improve the photovoltaic performance of mixed‐cation‐halide perovskite solar cells via a sequential deposition method.     

Low-Temperature Chemical Bath Deposition of Conformal and Compact NiOX for Scalable and Efficient Perovskite Solar Modules

A scalable and low-cost deposition of high-quality charge transport layers and photoactive perovskite layers are the grand challenges for large-area and efficient perovskite solar modules and tandem cells. An inverted structure with an inorganic hole transport layer is expected for long-term stability. Among various hole transport materials, nickel oxide has been investigated for highly efficient and stable perovskite solar cells. However, the reported deposition methods are either difficult for large-scale conformal deposition or require a high vacuum process. Chemical bath deposition is supposed to realize a uniform, conformal, and scalable coating by a solution process. However, the conventional chemical bath deposition requires a high annealing temperature of over 400 °C. In this work, an amino-alcohol ligand-based controllable release and deposition of NiO_X using chemical bath deposition with a low calcining temperature of 270 °C is developed. The uniform and conformal in-situ growth precursive films can be adjusted by tuning the ligand structure. The inverted structured perovskite solar cells and large-area solar modules reached a champion PCE of 22.03% and 19.03%, respectively. This study paves an efficient, low-temperature, and scalable chemical bath deposition route for large-area NiO_X thin films for the scalable fabrication of highly efficient perovskite solar modules.     

Simplified Perovskite Solar Cell with 4.1% Efficiency Employing Inorganic CsPbBr3 as Light Absorber

Perovskite solar cells with cost‐effectiveness, high power conversion efficiency, and improved stability are promising solutions to the energy crisis and environmental pollution. However, a wide‐bandgap inorganic–semiconductor electron‐transporting layer such as TiO₂ can harvest ultraviolet light to photodegrade perovskite halides, and the high cost of a state‐of‐the‐art hole‐transporting layer is an economic burden for commercialization. Here, the building of a simplified cesium lead bromide (CsPbBr₃) perovskite solar cell with fluorine‐doped tin oxide (FTO)/CsPbBr₃/carbon architecture by a multistep solution‐processed deposition technology is demonstrated, achieving an efficiency as high as 4.1% and improved stability upon interfacial modification by graphene quantum dots and CsPbBrI₂ quantum dots. This work provides new opportunities of building next‐generation solar cells with significantly simplified processes and reduced production costs.     

Matching Charge Extraction Contact for Wide‐Bandgap Perovskite Solar Cells

Efficient wide‐bandgap (WBG) perovskite solar cells are needed to boost the efficiency of silicon solar cells to beyond Schottky–Queisser limit, but they suffer from a larger open circuit voltage (V_OC) deficit than narrower bandgap ones. Here, it is shown that one major limitation of V_OC in WBG perovskite solar cells comes from the nonmatched energy levels of charge transport layers. Indene‐C60 bisadduct (ICBA) with higher‐lying lowest‐unoccupied‐molecular‐orbital is needed for WBG perovskite solar cells, while its energy‐disorder needs to be minimized before a larger V_OC can be observed. A simple method is applied to reduce the energy disorder by isolating isomer ICBA‐tran3 from the as‐synthesized ICBA‐mixture. WBG perovskite solar cells with ICBA‐tran3 show enhanced V_OC by 60 mV, reduced V_OC deficit of 0.5 V, and then a record stabilized power conversion efficiency of 18.5%. This work points out the importance of matching the charge transport layers in perovskite solar cells when the perovskites have a different composition and energy levels.     

Efficient Flexible Solar Cell based on Composition‐Tailored Hybrid Perovskite

Organic–inorganic hybrid perovskites (OIHPs) are new photoactive layer candidates for lightweight and flexible solar cells due to their low‐temperature process capability; however, the reported efficiency of flexible OIHP devices is far behind those achieved on rigid glass substrates. Here, it is revealed that the limiting factor is the different perovskite film deposition conditions required to form the same film morphology on flexible substrates. An optimized perovskite film composition needs a different precursor ratio, which is found to be essential for the formation of high‐quality perovskite films with longer radiative carrier recombination lifetime, smaller density of trap states, reduced precursor residue, and uniform and pin‐hole free films. A record efficiency of 18.1% is achieved for the flexible perovskite solar‐cell devices made on an indium tin oxide/poly(ethylene terephthalate) substrate via a low temperature (≤100 °C) solution process.     

Planar‐Structure Perovskite Solar Cells with Efficiency beyond 21%

Low temperature solution processed planar‐structure perovskite solar cells gain great attention recently, while their power conversions are still lower than that of high temperature mesoporous counterpart. Previous reports are mainly focused on perovskite morphology control and interface engineering to improve performance. Here, this study systematically investigates the effect of precise stoichiometry, especially the PbI₂ contents on device performance including efficiency, hysteresis and stability. This study finds that a moderate residual of PbI₂ can deliver stable and high efficiency of solar cells without hysteresis, while too much residual PbI₂ will lead to serious hysteresis and poor transit stability. Solar cells with the efficiencies of 21.6% in small size (0.0737 cm²) and 20.1% in large size (1 cm²) with moderate residual PbI₂ in perovskite layer are obtained. The certificated efficiency for small size shows the efficiency of 20.9%, which is the highest efficiency ever recorded in planar‐structure perovskite solar cells, showing the planar‐structure perovskite solar cells are very promising.     

Large‐Grain Tin‐Rich Perovskite Films for Efficient Solar Cells via Metal Alloying Technique

Fast research progress on lead halide perovskite solar cells has been achieved in the past a few years. However, the presence of lead (Pb) in perovskite composition as a toxic element still remains a major issue for large‐scale deployment. In this work, a novel and facile technique is presented to fabricate tin (Sn)‐rich perovskite film using metal precursors and an alloying technique. Herein, the perovskite films are formed as a result of the reaction between Sn/Pb binary alloy metal precursors and methylammonium iodide (MAI) vapor in a chemical vapor deposition process carried out at 185 °C. It is found that in this approach the Pb/Sn precursors are first converted to (Pb/Sn)I₂ and further reaction with MAI vapor leads to the formation of perovskite films. By using Pb–Sn eutectic alloy, perovskite films with large grain sizes up to 5 µm can be grown directly from liquid phase metal. Consequently, using an alloying technique and this unique growth mechanism, a less‐toxic and efficient perovskite solar cell with a power conversion efficiency (PCE) of 14.04% is demonstrated, while pure Sn and Pb perovskite solar cells prepared in this manner yield PCEs of 4.62% and 14.21%, respectively. It is found that this alloying technique can open up a new direction to further explore different alloy systems (binary or ternary alloys) with even lower melting point.     

Highly Efficient Perovskite–Perovskite Tandem Solar Cells Reaching 80% of the Theoretical Limit in Photovoltage

Organic–inorganic hybrid perovskite multijunction solar cells have immense potential to realize power conversion efficiencies (PCEs) beyond the Shockley–Queisser limit of single‐junction solar cells; however, they are limited by large nonideal photovoltage loss (V _oc,loss) in small‐ and large‐bandgap subcells. Here, an integrated approach is utilized to improve the V _oc of subcells with optimized bandgaps and fabricate perovskite–perovskite tandem solar cells with small V _oc,loss. A fullerene variant, Indene‐C₆₀ bis‐adduct, is used to achieve optimized interfacial contact in a small‐bandgap (≈1.2 eV) subcell, which facilitates higher quasi‐Fermi level splitting, reduces nonradiative recombination, alleviates hysteresis instabilities, and improves V _oc to 0.84 V. Compositional engineering of large‐bandgap (≈1.8 eV) perovskite is employed to realize a subcell with a transparent top electrode and photostabilized V _oc of 1.22 V. The resultant monolithic perovskite–perovskite tandem solar cell shows a high V _oc of 1.98 V (approaching 80% of the theoretical limit) and a stabilized PCE of 18.5%. The significantly minimized nonideal V _oc,loss is better than state‐of‐the‐art silicon–perovskite tandem solar cells, which highlights the prospects of using perovskite–perovskite tandems for solar‐energy generation. It also unlocks opportunities for solar water splitting using hybrid perovskites with solar‐to‐hydrogen efficiencies beyond 15%.     

Low‐Temperature Soft‐Cover Deposition of Uniform Large‐Scale Perovskite Films for High‐Performance Solar Cells

Large‐scale high‐quality perovskite thin films are crucial to produce high‐performance perovskite solar cells. However, for perovskite films fabricated by solvent‐rich processes, film uniformity can be prevented by convection during thermal evaporation of the solvent. Here, a scalable low‐temperature soft‐cover deposition (LT‐SCD) method is presented, where the thermal convection‐induced defects in perovskite films are eliminated through a strategy of surface tension relaxation. Compact, homogeneous, and convection‐induced‐defects‐free perovskite films are obtained on an area of 12 cm², which enables a power conversion efficiency (PCE) of 15.5% on a solar cell with an area of 5 cm². This is the highest efficiency at this large cell area. A PCE of 15.3% is also obtained on a flexible perovskite solar cell deposited on the polyethylene terephthalate substrate owing to the advantage of presented low‐temperature processing. Hence, the present LT‐SCD technology provides a new non‐spin‐coating route to the deposition of large‐area uniform perovskite films for both rigid and flexible perovskite devices.     

Realizing Stable Artificial Photon Energy Harvesting Based on Perovskite Solar Cells for Diverse Applications

As the fastest developing photovoltaic device, perovskite solar cells have achieved an extraordinary power conversion efficiency (PCE) of 25.3% under AM 1.5 illumination. However, few studies have been devoted to perovskite solar cells harvesting artificial light, owing to the great challenge in the simultaneous manipulation of bandgap‐adjustable perovskite materials, corresponding matched energy band structure of carrier transport materials, and interfacial defects. Herein, through systematic morphology, composition, and energy band engineering, high‐quality Cs_0.05MA_0.95PbBr_xI_3?x perovskite as the light absorber and Nb_yTi_1?yO₂ (Nb:TiO₂) as the electron transport material with an ideal energy band alignment are obtained simultaneously. The theoretical‐limit‐approaching record PCEs of 36.3% (average: 34.0 ± 1.2%) under light‐emitting diode (LED, warm white) and 33.2% under fluorescent lamp (cold white) are achieved simultaneously, as well as a PCE of 19.5% (average: 18.9 ± 0.3%) under solar illumination. An integrated energy conversion and storage system based on an artificial light response solar cell and sodium‐ion battery is established for diverse practical applications, including a portable calculator, quartz clock, and even environmental monitoring equipment. Over a week of stable operation shows its great practical potential and provides a new avenue to promote the commercialization of perovskite photovoltaic devices via integration with ingenious electronic devices.     

Solution‐Phase Epitaxial Growth of Perovskite Films on 2D Material Flakes for High‐Performance Solar Cells

The quality of perovskite films is critical to the performance of perovskite solar cells. However, it is challenging to control the crystallinity and orientation of solution‐processed perovskite films. Here, solution‐phase van der Waals epitaxy growth of MAPbI₃ perovskite films on MoS₂ flakes is reported. Under transmission electron microscopy, in‐plane coupling between the perovskite and the MoS₂ crystal lattices is observed, leading to perovskite films with larger grain size, lower trap density, and preferential growth orientation along (110) normal to the MoS₂ surface. In perovskite solar cells, when perovskite active layers are grown on MoS₂ flakes coated on hole‐transport layers, the power conversion efficiency is substantially enhanced for 15%, relatively, due to the increased crystallinity of the perovskite layer and the improved hole extraction and transfer rate at the interface. This work paves a way for preparing high‐performance perovskite solar cells and other optoelectronic devices by introducing 2D materials as interfacial layers.     

Compositional Engineering for Thermally Stable,Highly Efficient Perovskite Solar Cells Exceeding 20% Power Conversion Efficiency with 85 °C/85% 1000 h Stability

Perovskite solar cells have received great attention because of their rapid progress in efficiency, with a present certified highest efficiency of 23.3%. Achieving both high efficiency and high thermal stability is one of the biggest challenges currently limiting perovskite solar cells because devices displaying stability at high temperature frequently suffer from a marked decrease of efficiency. In this report, the relationship between perovskite composition and device thermal stability is examined. It is revealed that Rb can suppress the growth of PbI₂ even under PbI₂‐rich conditions and decreasing the Br ratio in the perovskite absorber layer can prevent the generation of unwanted RbBr‐based aggregations. The optimized device achieved by engineering perovskite composition exhibits 92% power conversion efficiency retention in a stress test conducted at 85 °C/85% relative humidity (RH) according to an international standard (IEC 61215) while exceeding 20% power conversion efficiency (certified efficiency of 20.8% at 1 cm²). These results reveal the great potential for the practical use of perovskite solar cells in the near future.     

Dual‐Source Precursor Approach for Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

The highest efficiencies reported for perovskite solar cells so far have been obtained mainly with methylammonium and formamidinium mixed cations. Currently, high‐quality mixed‐cation perovskite thin films are normally made by use of antisolvent protocols. However, the widely used “antisolvent”‐assisted fabrication route suffers from challenges such as poor device reproducibility, toxic and hazardous organic solvent, and incompatibility with scalable fabrication process. Here, a simple dual‐source precursor approach is developed to fabricate high‐quality and mirror‐like mixed‐cation perovskite thin films without involving additional antisolvent process. By integrating the perovskite films into the planar heterojunction solar cells, a power conversion efficiency of 20.15% is achieved with negligible current density–voltage hysteresis. A stabilized power output approaching 20% is obtained at the maximum power point. These results shed light on fabricating highly efficient perovskite solar cells via a simple process, and pave the way for solar cell fabrication via scalable methods in the near future.     

Thermally Stable MAPbI3 Perovskite Solar Cells with Efficiency of 19.19% and Area over 1 cm2 achieved by Additive Engineering

Solution‐processed perovskite (PSC) solar cells have achieved extremely high power conversion efficiencies (PCEs) over 20%, but practical application of this photovoltaic technology requires further advancements on both long‐term stability and large‐area device demonstration. Here, an additive‐engineering strategy is developed to realize a facile and convenient fabrication method of large‐area uniform perovskite films composed of large crystal size and low density of defects. The high crystalline quality of the perovskite is found to simultaneously enhance the PCE and the durability of PSCs. By using the simple and widely used methylammonium lead iodide (MAPbI₃), a certified PCE of 19.19% is achieved for devices with an aperture area of 1.025 cm², and the high‐performing devices can sustain over 80% of the initial PCE after 500 h of thermal aging at 85 °C, which are among the best results of MAPbI₃‐based PSCs so far.     

Highly Efficient Porphyrin‐Based OPV/Perovskite Hybrid Solar Cells with Extended Photoresponse and High Fill Factor

Employing a layer of bulk‐heterojunction (BHJ) organic semiconductors on top of perovskite to further extend its photoresponse is considered as a simple and promising way to enhance the efficiency of perovskite‐based solar cells, instead of using tandem devices or near infrared (NIR)‐absorbing Sn‐containing perovskites. However, the progress made from this approach is quite limited because very few such hybrid solar cells can simultaneously show high short‐circuit current (J_SC) and fill factor (FF). To find an appropriate NIR‐absorbing BHJ is essential for highly efficient, organic, photovoltaics (OPV)/perovskite hybrid solar cells. The materials involved in the BHJ layer not only need to have broad photoresponse to increase J_SC, but also possess suitable energy levels and high mobility to afford high V_OC and FF. In this work, a new porphyrin is synthesized and blended with [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) to function as an efficient BHJ for OPV/perovskite hybrid solar cells. The extended photoresponse, well‐matched energy levels, and high hole mobility from optimized BHJ morphology afford a very high power conversion efficiency (PCE) (19.02%) with high V_oc, J_SC, and FF achieved simultaneously. This is the highest value reported so far for such hybrid devices, which demonstrates the feasibility of further improving the efficiency of perovskite devices.     

Polarized Ferroelectric Polymers for High‐Performance Perovskite Solar Cells

In hybrid organic–inorganic lead halide perovskite solar cells, the energy loss is strongly associated with nonradiative recombination in the perovskite layer and at the cell interfaces. Here, a simple but effective strategy is developed to improve the cell performance of perovskite solar cells via the combination of internal doping by a ferroelectric polymer and external control by an electric field. A group of polarized ferroelectric (PFE) polymers are doped into the methylammonium lead iodide (MAPbI₃) layer and/or inserted between the perovskite and the hole‐transporting layers to enhance the build‐in field (BIF), improve the crystallization of MAPbI₃, and regulate the nonradiative recombination in perovskite solar cells. The PFE polymer‐doped MAPbI₃ shows an orderly arrangement of MA⁺ cations, resulting in a preferred growth orientation of polycrystalline perovskite films with reduced trap states. In addition, the BIF is enhanced by the widened depletion region in the device. As an interfacial dipole layer, the PFE polymer plays a critical role in increasing the BIF. This combined effect leads to a substantial reduction in voltage loss of 0.14 V due to the efficient suppression of nonradiative recombination. Consequently, the resulting perovskite solar cells present a power conversion efficiency of 21.38% with a high open‐circuit voltage of 1.14 V.