Characterization and optical properties of bismuth chalcogenide films prepared by pulsed laser deposition technique

Thin films of Bi-based chalcogenides were prepared by pulsed laser deposition (PLD) technique according to the stoichiometric formula: Bi₂(Se_1−xTe_x)₃. Their optical properties were studied aiming to find the suitable area of application and the optimum composition amongst the samples under study. X-ray diffraction analysis proved the crystallinity of the deposited samples; in addition, surface roughness and films homogeneity were studied by atomic force microscopy (AFM) confirming the suitability of PLD technique to prepare homogenous and smooth films of the concerned alloys. Absorption coefficient calculations showed higher absorption values of 5×10⁵ and 6×10⁵ cm⁻¹ for Te contents of 90% and 100% in the Bi₂(Se_1−xTe_x)₃ system respectively. Optical band gap of the concerned films were calculated and found to be in the range of 0.76–1.11 eV, exhibiting comparable values with the previously reported by other authors. Optical studies conformed direct and allowed transitions in all films. Refractive index (n) and dielectric constants (Ɛ_r) and (Ɛ_i) were calculated and studied as a function of the wavelength. Values and behavior of (n), (Ɛ_r) and (Ɛ_i) indicated strong dependence on the composition and the wavelength range.     

Influence of heat treatment on the structural,optical and electrical properties of Cd20Sn10Se70 thin films

The effect of annealing temperature (T_a) on the structural, optical, and electrical properties of thermally evaporated Cd₂₀Sn₁₀Se₇₀ thin films has been investigated. Differential Thermal Analysis (DTA) was used to determine the glass transition temperature (T_g) of the prepared alloy. X-ray diffraction studies showed that the as-deposited film and the films that were annealed at T_a<T_g are of low crystallinity. On annealing above T_g, these films showed a polycrystalline nature. The surface morphology and microstructure of as-deposited and annealed films have been examined by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Their optical constants were calculated from the transmittance measurements in the range 200–2500 nm. The dispersion of refractive index was analyzed in terms of the single-oscillator Wemple-Di Domenico model. Analysis of the optical absorption data indicates that the optical band gap E_g of these films obeys Tauc׳s relation for the allowed direct transition. The optical band gap E_g as well as the activation energy for the electrical conduction ∆E were found to increase with increase of annealing temperature up to T_g, whereas above T_g there is a remarkable decrease in both E_g and ∆E. The obtained results were interpreted in terms of the Mott-Davis model and amorphous–crystalline transformation.     

Effects of Sb,Zn doping on structural,electrical and optical properties of SnO2 thin films

Highly transparent, low resistive pure and Sb, Zn doped nanostructured SnO₂ thin films have been successfully prepared on glass substrates at 400° C by spray pyrolysis method. Structural, electrical and optical properties of pure and Sb, Zn doped SnO₂ thin films are studied in detail. Powder X-ray diffraction confirms the phase purity, increase in crystallinity, size of the grains (90–45 nm), polycrystalline nature and tetragonal rutile structure of thin films. The scanning electron microscopy reveals the continuous change in surface morphology of thin films and size of the grains decrease due to Sb, Zn doping in to SnO₂. The optical transmission spectra of SnO₂ films as a function of wavelength confirm that the optical transmission increases with Sb, Zn doping remarkably. The optical band gap of undoped film is found to be 4.27 eV and decreases with Sb, Zn doping to 4.19 eV, 4.07 eV respectively. The results of electrical measurements indicate that the sheet resistance of the deposited films improves with Sb, Zn doping. The Hall measurements confirm that the films are degenerate n-type semiconductors.     

Antimony sulfide (Sb2S3) thin films by pulse electrodeposition: Effect of thermal treatment on structural,optical and electrical properties

Antimony sulfide films have been deposited by pulse electrodeposition on Fluorine doped SnO₂ coated glass substrates from aqueous solutions containing SbCl₃ and Na₂S₂O₃. The crystalline structure of the films was characterized by X-ray diffraction, Raman spectroscopy and TEM analysis. The deposited films were amorphous and upon annealing in nitrogen/sulfur atmosphere at 250 °C for 30 min, the films started to become crystalline with X-ray diffraction pattern matching that of stibnite, Sb₂S₃, (JCPDS 6-0474). AFM images revealed that Sb₂S₃ films have uniformly distributed grains on the surface and the grain agglomeration occurs with annealing. The optical band gap calculated from the transmittance and the reflectance studies were 2.2 and 1.65 eV for as deposited and 300 °C annealed films, respectively. The annealed films were photosensitive and exhibited photo-to-dark current ratio of two orders of magnitude at 1 kW/m² tungsten halogen radiation.     

Effect of thickness on the structural,optical and electrical properties of RF magnetron sputtered GZO thin films

Gallium-doped zinc oxide (GZO) thin films with very high conductivity and transparency were successfully deposited by RF magnetron sputtering at a substrate temperature of 400 °C. The dependence of the film properties over the thickness was investigated. X-ray diffraction (XRD) results revealed the polycrystalline nature of the films with hexagonal wurtzite structure having preferential orientation along [001] direction normal to the substrate. The lowest resistivity obtained from electrical studies was 5.4×10⁻⁴ Ω cm. The optical properties were studied using a UV–vis spectrophotometer and the average transmittance in the visible region (400–700 nm) was found to be 92%, relative to the transmittance of a soda–lime glass reference for a GZO film of thickness 495 nm and also the transparency of the films decreases in the near IR region of the spectra. The mobility of the films showed a linear dependence with crystallite size. GZO film of thickness 495 nm with the highest figure of merit indicates that the GZO film is suitable as an ideal transparent conducting oxide (TCO) material for solar cell applications.     

Effect of temperature on structural and optical properties of ZnS thin films by chemical bath deposition without stirring the reaction bath

ZnS thin films were deposited at different temperatures on glass substrates by chemical bath deposition method without stirring the deposition bath. With deposition temperature increasing from 50 °C to 90 °C, pH decreases rapidly, homogeneous precipitation of ZnS, instead of Zn(OH)₂ easily forms in the bath. It means that higher temperature is favorable for the formation of relatively high stoichiometric film, due to the lower concentration of OH⁻. The thickness of the films deposited at 90 °C is much higher than that of the films deposited at 50 °C and 70 °C. Combining the film thickness with the change of pH, the growth of film, especially deposited at 90 °C mainly comes from the fluctuation region of pH. At the same time, with the increase of deposition temperature, the obtained films are transparent, homogeneous, reflecting, compact, and tightly adherent. The ZnS films deposited for 1.5 h, 2 h and 2.5 h at 70 °C and 90 °C have the cubic structure only after single deposition. The average transmission of all films, especially the thicker films deposited at 90 °C, is greater than 90% for wavelength values in the visible region. Comparing with the condition of stirring, the structural and optical properties of films are improved significantly. The direct band gaps range from 3.93 to 4.06 eV.     

Effect of thermal annealing on structural and optical properties of titanyl phthalocyanine thin films

Thin films of titanyl phthalocyanine (TiOPc) have been deposited on both fused quartz and glass substrates by the thermal evaporation technique. The structural and optical properties of the as-deposited and annealed films have been reported. The structural features of the as-deposited and annealed films have been studied by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), and Fourier-transform infrared (FT-IR) technique. The optical constants (refractive index, n, and absorption index, k) of the films have been presented for the first time in the wavelength range 200–2500 nm by using spectrophotometric measurements at nearly normal incidence. The band gaps of the as-deposited film at 1.48 eV and 2.5 eV corresponding to Q-band and B or Soret band were red-shifted to 1.15 eV and 2.19 eV, respectively, when the film annealed at 433 K.     

Effect of annealing temperature on structural,electrical and optical properties of spray pyrolytic nanocrystalline CdO thin films

Nanocrystalline CdO thin films were prepared onto a glass substrate at substrate temperature of 300 °C by a spray pyrolysis technique. Grown films were annealed at 250, 350, 450 and 550 °C for 2.5 h and studied by the X-ray diffraction, Hall voltage measurement, UV-spectroscopy, and scanning electron microscope. The X-ray diffraction study confirms the cubic structure of as-deposited and annealed films. The grain size increases whereas the dislocation density decreases with increasing annealing temperature. The Hall measurement confirms that CdO is an n-type semiconductor. The carrier density and mobility increase with increasing annealing temperature up to 450 °C. The temperature dependent dc resistivity of as-deposited film shows metallic behavior from room temperature to 370 K after which it is semiconducting in nature. The metallic behavior completely washed out by annealing the samples at different temperatures. Optical transmittance and band gap energy of the films are found to decrease with increasing annealing temperature and the highest transmittance is found in near infrared region. The refractive index and optical conductivity of the CdO thin films enhanced by annealing. Scanning electron microscopy confirms formation of nano-structured CdO thin films with clear grain boundary.     

Structural,optical, photoluminescence,electrochemical, and photoelectrochemical properties of Fe doped ZnSe hexagonal nanorods

The present investigation describes that the iron (Fe) doped ZnSe hexagonal nanorods were successfully synthesized via chemical synthesis specifically galvanostatic mode of electrodeposition and addition of Fe in order to improve the PEC performance of ZnSe electrodes using a galvanostatic mode. These crystalline Fe doped ZnSe hexagonal nanorods electrodes are characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and optical properties, such as UV–vis spectroscopy, photoluminescence spectroscopy, electrochemical impedance spectroscopy (EIS), Raman spectroscopy and photoelectrochemical properties. It is seen that at 5% Fe doped ZnSe hexagonal nanorods show the open circuit voltage (V_oc) was 100 mV, and short circuit current (I_sc) was 110 μA. The observed fill factor and efficiency were found to be 44% and 0.15%, respectively.     

Effect of Ar ion irradiation on structural and optical properties of e-beam evaporated cadmium telluride thin films

CdTe thin films were prepared using e-beam evaporation technique. The prepared films were irradiated by Ar⁺ ions at different fluencies using multipurpose aluminum (Al) probe as in-situ. This could also be used in ion bombardment for cleaning the substrate prior to coating. The as grown and Ar⁺ ion irradiated films were confirmed to be of polycrystalline nature with X-ray technique. Ar⁺ ion irradiation enhances the growth of (1 1 1) oriented CdTe crystals and the Cd enrichment on the surface of CdTe thin films. Higher Ar⁺ ion flux helps to grow (2 2 0) oriented CdTe thin film. A considerable change in structural parameters like crystallite size, lattice parameter, internal strain, etc. could be observed as a result of high Ar⁺ ion flux. The applied in-plan stress in both as grown and irradiated film was identified to be of tensile nature. The applied stress was observed between 0.016 and 0.067 GPa for all Ar⁺ ion irradiated samples. As a result of the Ar⁺ ion irradiation, the in-plan stress varies between 1.38×10⁹ and 5.58×10⁹ dyn/cm². The observed bad gap was increased for higher Ar⁺ ion flux. It shows the effect of Ar⁺ ion irradiation on the modifications of optical properties. The observed results were encouraging on the use of simple multipurpose Al probe for Ar⁺ ion irradiation process as in-situ.     

The effect of annealing on the physical properties of thermally evaporated CuIn2n+1S3n+2 thin films (n=0, 1, 2 and 3)

In this study, the annealing effect on structural, electrical and optical properties of CuIn_2n+1S_3n+2 thin films (n=0, 1, 2 and 3) are investigated. CuIn_2n+1S_3n+2 films were elaborated by vacuum thermal evaporation and annealed at 150 and 250 °C during 2 h in air atmosphere. XRD data analysis shows that CuInS₂ and CuIn₃S₅ (n=0 and 1) crystallize in the chalcopyrite structure according to a preferential direction (112), CuIn₅S₈ and CuIn₇S₁₁ (n=2 and 3) crystallize in the cubic spinel structure with a preferential direction (311). The optical characterization allowed us to determine the optical constants (refractive indexes 2.2–3.1, optical thicknesses 250–500 nm, coefficients of absorption 10⁵ cm^?1, coefficients of extinction <1, and the values of the optical transitions 1.80–2.22 eV) of the samples of all materials. We exploited the models of Cauchy, Wemple–DiDomenico and Spitzer–Fan for the analysis of the dispersion of the refractive index and the determination of the optical and dielectric constants.     

Thickness dependent physical properties of chemically deposited nanocrystalline MgSe thin films deposited at room temperature by solution growth method

Chemical bath deposition method has been employed to deposit nanocrystalline magnesium selenide thin films of thickness 104–292 nm onto glass substrates at room temperature. The deposition bath consists of magnesium chloride, triethanolamine (TEA) and selenium dioxide. The as deposited films were characterized by X-ray diffraction, scanning electron microscopy (SEM), atomic force microscopy (AFM), optical absorption, electrical resistivity and thermo-emf measurements. The X-ray diffraction (XRD) studies revealed that the crystallinity of the magnesium selenide thin film increases with thickness. SEM studies reveal that MgSe films exhibit uniform distribution of round shaped grains over the entire substrate surface.The optical band-gap and electrical resistivity of MgSe film decrease as the film thickness increases. Such type of dependence is attributed to the quantum size effect that is observed in nanocrystalline semiconductors.The thermo-emf measurement confirms its p-type conductivity.     

Studies on the properties of sputter-deposited Ag-doped ZnO films

Ag-doped ZnO films were prepared by simultaneous rf magnetron sputtering of ZnO and dc magnetron sputtering of Ag on glass substrate. The influences of dopant content and substrate temperature on the properties of the as-grown films were investigated. Several analytical tools such as X-ray diffraction, spectrophotometer, atomic force microscopy, scanning electron microscopy and four-point probe were used to explore the possible changes in electrical and optical properties. The as-grown film has a preferred orientation in the (0 0 2) direction. As the amounts of the Ag dopant were increased, the crystallinity as well as the transmittance and optical band gap were decreased while the electrical resistivity increased. However, as the substrate temperature was increased, the crystallinity and the transmittance were increased. A small amount of Ag (<1 at%) lowered the resistivity by 30% with only a slight decrease in the visible transparency.     

Optical,morphological and electrical studies of Zn:PbS thin films

Structural, electrical, and optical properties of undoped and Zn doped lead sulfide (PbS) thin films are benign reported in this paper. The subjected films were grown on glass substrates at 25 °C by a chemical bath deposition (CBD) method. The concentration of Zn in the deposition bath represented by the ratio [Zn²⁺]/[Pb²⁺] was varied from 0% to 5%. It was found that the film׳s grains decreased in size with increasing Zn content in the film. XRD data showed the polycrystalline nature of the film its crystal orientation peak intensities decreased with higher doping concentration of Zn. Atomic force microscopy (AFM) measurements revealed that the surface roughness of the films decreased due to zinc doping as well. However, with increasing of the dopant concentration from 0% to 5%, the average transmittance of the films varied over the range of 35–75%. The estimated optical band (E_g) gaps of undoped and Zn doped PbS thin films were in the range of 0.72–1.46 eV. Hall Effect measurements electrical resistivity, carrier concentration and Hall mobility have been determined for the titled film as functions on the Zn content within the film׳s textures. The overall result of this work suggested that the Zn:PbS film is a good candidate as an absorber layer in the modern solar cell devices.     

Effect of the deposition rate on the phase transition in silver telluride thin films

Silver telluride thin films of thickness 50 nm have been deposited at different deposition rates on glass substrates at room temperature and at a pressure of 2×10⁻⁵ mbar. The electrical resistivity was measured in the temperature range 300–430 K. The temperature dependence of the electrical resistance of Ag₂Te thin films shows structural phase transition and coexistence of low temperature monoclinic phase and high temperature cubic phase. The effect of deposition rate on the phase transition and the electrical resistivity of silver telluride thin films in relation to carrier concentration and mobility are discussed.     

Influence of annealing temperature on the phase composition and optical properties of CuInS2 films

We studied the growth of CuInS₂ thin films by single-source evaporation of CuInS₂ powder in a high-vacuum system with a base pressure of 10^?3 Pa. After evaporation, the films were annealed in a sulfur atmosphere at temperatures from 200 to 500 °C for 1 h. XRD curves and Raman spectra of the films demonstrated that chalcopyrite CuInS₂ was the major crystalline phase. The morphology of Cu_xS exhibited a star-like structure, which we report for the first time. The phase composition and optical properties of our polycrystalline thin films were effectively modified by annealing in S. For films annealed at 200 and 350 °C, a secondary CuIn₁₁S₁₇ phase appeared, which may be related to solid-state reaction in the S atmosphere. This secondary CuIn₁₁S₁₇ phase has not been widely reported in previous studies. After annealing at 500 °C, only a chalcopyrite phase was detected, with bandgap energy of 1.46 eV, which is nearly identical to the optimal bandgap energy (1.5 eV) of single-crystal CuInS₂. This indicates that the composition of the CuInS₂ film annealed at 500 °C was nearly stoichiometric. The bandgap of the samples first increased and then decreased with increasing annealing temperature, which may be attributed to an increase in grain size, the secondary CuIn₁₁S₁₇ phase, and deviation from stoichiometry.     

Optical and electrical measurement of FeSe2 thin films obtained at low temperature

FeSe₂ thin films were prepared at low temperature by thermal annealing at 350 °C during 6 h of sequentially evaporated iron and selenium films under selenium atmosphere. The structural, optical and electrical characteristics were investigated. The roughness of films (~76 nm) was confirmed by AFM images. Moreover, optical band gap of FeSe₂, which was evaluated as nearly 1.11 eV and confirmed by the electrical study which yielded a value in the order of 1.08 eV. The electrical conductivity, conduction mechanism, dielectric properties and relaxation model of theses thin films were studied using impedance spectroscopy technique in the frequency range 5 Hz–13 MHz under various temperatures (180–300 °C). Besides, complex impedance and AC conductivity have been investigated on the basis of frequency and temperature dependence.     

Effect of fluorine doping on the structural,optical and electrical properties of spray deposited cadmium stannate thin films

Cadmium stannate (Cd₂SnO₄) thin films were coated on Corning 1737 glass substrates at 540 °C by spray pyrolysis technique, from the aqueous solution of cadmium acetate and tin (II) chloride precursors. Fluorine doped Cd₂SnO₄ (F: Cd₂SnO₄) thin films were prepared by adding ammonium fluoride in the range of 0–5 wt% of the total weight of cadmium acetate and tin (II) chloride in the spray solution. Thickness of the prepared films is about 300 nm. X-ray diffraction analysis of the Cd₂SnO₄ and 3 wt% F: Cd₂SnO₄ films shows the signature for the growth along (222) direction. Scanning electron micrographs showed that fluorine doping effectively modifies the surface morphology of Cd₂SnO₄ films. Average optical transmittance in the visible region (500–850 nm) for Cd₂SnO₄ is ~79% and it is increased to ~83% for 1 wt% doping concentration of the NH₄F in the solution. Fluorescence spectra of F: Cd₂SnO₄ (1 wt% and 3 wt%) exhibit peak at 601 nm. F: Cd₂SnO₄ film (1 wt%) shows mobility of ~42 cm²/V s, carrier concentration of ~9.5×10¹⁹ cm^?3 and resistivity of ~1.5×10^?3 Ω cm.     

Effect of post-growth annealing on the structural,optical and electrical properties of V2O5 nanorods and its fabrication,characterization of V2O5/p-Si junction diode

We report the synthesis of V₂O₅ nanorods by utilizing simple wet chemical strategy with ammonia meta vanadate (NH₄VO₃) and polyethylene glycol (PEG) exploited as precursor and surfactant agent, respectively. The effect of post-annealing on structural, optical and electrical properties of V₂O₅ nanorods was characterized by XRD, HRSEM-EDX, TEM, FT-IR, UV (DRS), PL, TG–DTA and DC conductivity studies. The X-ray diffraction analysis revealed that the prepared sample annealed at 150 °C for 5 h which exhibited anorthic phase of V₅O₉ and annealed at 300–600 °C showed the anorthic phase change to orthorhombic phase of V₂O₅ due to the post-annealing effect. The surface morphology results indicated that increasing temperature caused a change from microrods to a nanorods shape in the morphology of V₂O₅. FT-IR spectrum confirmed that the presence of V₂O₅ functional groups and the formation of V–O bond. The optical band gap was found in the range 2.5–2.48 eV and observed to decreases with various annealed temperature. The DC electrical conductivity was studied as a function of temperature which indicated the semiconducting nature. Further, the potential of V₂O₅ nanostructures were grown on the p-Si substrate using the nebulizer spray technique. The junction properties of the V₂O₅/p-Si diode were evaluated by measuring current (I)–voltage (V) and AC characteristics.