Magnetic and FTIR studies of BixY3−xFe5O12 (x = 0, 1, 2) powders prepared by the metal organic decomposition method

The crystallization process of bismuth substituted yttrium iron garnet (Bi_xY_3−xFe₅O₁₂; x = 0, 1, 2) powder prepared by the metal-organic decomposition method has been studied with various sintering temperatures. The pure garnet phase was observed for the x = 1 powder at 900 °C sintering temperature, whereas the x = 0, 2 powder showed secondary phases. The x = 0 powder showed a similar crystallization process to that of the solid state reaction method. For the x =1, 2 powders, it is proposed that the lowering of the crystallization temperature is due to the lowered stability of the intermediate phase. The infrared spectroscopy and magnetic properties were also investigated. The pure garnet phase showed three absorption bands located at 563, 598, 655 cm⁻¹ that shifted to 555, 588, 639 cm⁻¹ along with an increase of bismuth concentration. The maximum values of saturation and remanence magnetization and the minimum value of coercivity were observed for the x = 1 powder sintered at 900 °C, which were 20.8 emu/g, 2.67 emu/g, and 31.9 Oe, respectively.     

MOCVD growth and characterizations of BxAl1−xAs and BxAl1−x−yInyAs alloys

Zinc-blende B_xAl_1−xAs and B_xAl_1−x−yIn_yAs alloys have been grown on exactly oriented (0 0 1)GaAs substrates by low pressure metalorganic chemical vapor deposition (LP-MOCVD). The influence of susceptor coating, growth temperature and gas-phase boron mole fraction on boron incorporation into AlAs has been comprehensively investigated. It has been found that boron incorporation into AlAs could be enhanced and the optimal growth temperature range of B_xAl_1−xAs alloys changed from 580 °C to 610 °C when SiC-coated graphite susceptors were replaced by the non-coated ones. In this study, the maximum boron composition x of 2.8% was achieved for the pseudomorphically strained B_xAl_1−xAs alloys. AFM measurements show that RMS roughness of B_xAl_1−xAs alloys increased sharply with the increase of gas-phase boron mole fraction. Raman spectra of B_xAl_1−xAs alloys show a linear increase of the BAs shift with boron composition x. Based on BAlAs deposition, bulk B_xAl_1−x−yIn_yAs (x = 1.9%) quaternary alloy was grown lattice-matched to GaAs successfully. Moreover, 10-period BAlAs/GaAs and BAlInAs/GaAs MQW heterostructures were also demonstrated.     

Room temperature electroresistance in Sr2−xGdxMnTiO6 perovskites (0 ≤ x ≤ 1)

We report on the room temperature strong (∼80%) electroresistance (ER) in the double perovskite with mixed Mn valence: Sr_2−xGd_xMnTiO₆, 0 ≤ x ≤ 1. Both, continuous and pulsed current-voltage curves are almost identical which indicates that the observed electroresistance is not associated with heating. This is also supported by simultaneous temperature measurements. ER is negligible (absent) in the x = 0 compound and increases with the increase of Gd content ‘x’. The amplitude of ER has a maximum for x = 0.75, suggesting that ER is determined by both the double exchange and the Mn³⁺ concentration. At the same time, magnetic interactions change from the antiferromagnetic (x = 0) to ferromagnetic ones as x → 1, thus linking the ER with ferromagnetism.     

Synthesis, structural and microwave dielectric properties of Al2W3−xMoxO12 (x = 0-3) ceramics

Low dielectric ceramics in the Al₂W_3−xMo_xO₁₂ (x = 0-3) system have been prepared through solid state ceramic route. The phase purity of the ceramic compositions has been studied using powder X-ray diffraction (XRD) studies. The microstructure of the sintered ceramics was evaluated by Scanning Electron Microscopy (SEM). The crystal structure of the ceramic compositions as a result of Mo substitution has been studied using Laser Raman spectroscopy. The microwave dielectric properties of the ceramics were studied by Hakki and Coleman post resonator and cavity perturbation techniques. Al₂Mo_xW_3−xO₁₂ (x = 0-3) ceramics exhibited low dielectric constant and relatively high unloaded quality factor. The temperature coefficient of resonant frequency of the compositions is found to be in the range −41 to −72 ppm/°C.     

Crystal structure and magnetic properties of DyCuxGa2−x (x = 0-2.0) antiferromagnetic compounds

DyCu_xGa_2−x (x = 0-2.0) compounds have been synthesized; meanwhile, their crystal structure and magnetic properties have been investigated by X-ray diffraction and magnetic measurements. The result shows that the continuous solid-solution series crystallize in three phases, with the structure types of AlB₂ (x = 0-0.2), DyCuGe (x = 0.3-0.6) and CeCu₂ (x = 0.7-2.0), respectively. The main reason to form the three structure types is considered to be the average atomic radius ratio of R to Cu/Ga. Magnetic-ordering transition of the compounds with x = 0.2-0.6 takes place at about 20 K and 113 K, while those of other compounds only takes place at about 20 K, which is attributed to the change of the near Dy-Dy distances and the ordered substitution of Ga by Cu.     

Thermoelectric properties of Cu1−xPtxFeO2 (0.0 ≤ x ≤ 0.05) delafossite-type transition oxide

The samples of Cu_1−xPt_xFeO₂ (0 ≤ x ≤ 0.05) delafossite were synthesized by solid state reaction method for studying thermoelectric properties. The properties of Seebeck coefficient, electrical conductivity and thermal conductivity were measured in the high temperature ranging from 300 to 960 K. The results of Seebeck coefficient, electrical conductivity and power factor were increased with increasing Pt substitution and temperature. The thermal conductivity was decreased from 5.8 to 3.5 W/mK with increasing the temperature from 300 to 960 K. An important results, the highest value of power factor and ZT is 2.0 × 10⁻⁴ W/mK² and 0.05, respectively, for x = 0.05 at 960 K.     

Preparation and characterization of La1−xKxFeO3 (x = 0-1) by self-propagating high-temperature synthesis for use as soot combustion catalyst

This paper proposes La_1−xK_xFeO₃ prepared by self-propagating high-temperature synthesis (SHS) as an alternative to platinum catalysts for promoting diesel soot combustion. The catalytic property of eleven products SHSed with different substitution ratios of potassium (x = 0-1) was experimentally evaluated using a thermobalance. In the mass loss curves of the product, T₅₀ was defined as the temperature at which the weight of the reference soot decreases to half its initial weight. The BET specific surface area of SHSed La_1−xK_xFeO₃ depended on x strongly. All the products showed good oxidation catalytic activity. Despite having the smallest surface area (0.11 m²/g) among the obtained products, La_0.9K_0.1FeO₃ (x = 0.1) was found to be the best catalyst with the lowest T₅₀ (442 °C). T₅₀ of La_1−xK_xFeO₃ decreased with increasing x for x > 0.2. The products with x = 0.6 and 0.8 were the second-best catalysts in terms of their T₅₀. Moreover, average apparent activation energy of La_0.9K_0.1FeO₃ (x = 0.1) calculated by Friedman method using TG was as much as 61 kJ/mol lower than that of Pt/Al₂O₃ catalyst. In conclusion, potassium-substituted SHSed La_1−xK_xFeO₃ can be used as an alternative to Pt/Al₂O₃ for soot combustion.     

High-Q microwave dielectrics in the (Mg1−xZnx)Al2O4 (x = 0-0.1) system

The microwave dielectric properties and the microstructures of (Mg_1−xZn_x)Al₂O₄ (x = 0-0.1) ceramic system prepared by the conventional solid-state route were investigated. The forming of spinel-structured (Mg_1−xZn_x)Al₂O₄ (x = 0-0.1) solid solutions was confirmed by the XRD patterns and the measured lattice parameters, which linearly varied from a = b = c = 8.0815 Å for MgAl₂O₄ to a = b = c= 8.0828 Å for (Mg_0.9Zn_0.1)Al₂O₄. By increasing x, the Q × f of (Mg_1−xZn_x)Al₂O₄ can be tremendously boosted from 82,000 GHz at x = 0 to a maximum of 156,000 GHz at x = 0.05. The Zn substitution was effective in reducing the dielectric loss without detrimental effects on the ?_r and τ_f values of the ceramics.     

Effect of the sintering temperature on the properties of nanocrystalline Ca1−xSmxMnO3 (0 ≤ x ≤ 0.4) powders

Nanocrystalline Ca_1−xSm_xMnO₃ (0 ≤ x ≤ 0.4) manganites were prepared by a soft chemical method (Pechini method) followed by auto-combustion and sintering in air at 1073 or 1473 K. Single-phase powders with general composition Ca_1−xSm_xMnO₃ were obtained after 18 h annealing. The particle and grain sizes of the substituted Sm-manganites did not exhibit variation with samarium content, but increase with increasing the sintering temperature. All manganites show two active IR vibrational modes near 400 and 600 cm⁻¹ characteristic of the BO₆ octahedron vibrations.For the samples sintered at T_s = 1473 K, the partial substitution of calcium by samarium in the CaMnO₃ phase induces a marked decrease in the electrical resistivity, in the temperature range of 300-900 K, and at the same time a metal-to-insulator transition occurs; for T_s = 1073 K all the samples present semiconductor behaviour. With the increase of the annealing temperature the grain size increases and a metal-semiconductor transition appears. The results can be ascribed to the Mn⁴⁺/Mn³⁺ ratio and particle grain size. The effects of particle size on the electrical properties can be attributed to the domain status, changes in the Mn-O-Mn bond angle and Mn-O bond length.     

The effects of thermal treatment on the physical properties of Sr2FeMo1−xMxO6 perovskite with M = W, Ta and x ≤ 0.3

The Sr₂FeMo_1−xM_xO₆ double perovskites with M = W and Ta and x ≤ 0.3, were obtained by sintering at 1300 °C, during 4 and 8 h, respectively. The perovskites crystallize in a tetragonal structure having I4/mmm space group. The grains are more homogeneous when sintering time is increased. The samples sintered longer time show higher values of saturation magnetizations, resistivities and magnetoresistivities than the samples sintered during 4 h. The intergrain tunnelling magnetoresistance as well as the intragrain contributions, respectively were analysed as function of temperature and external field. The changes in the physical properties, when the sintering time is increased, have been correlated with the number of antisite defects as well as the nature of grain boundaries.     

Synthesis and thermoelectric properties of the PbSe1−xTex alloys

The PbSe_1−xTe_x alloys with x = 0.2, 0.3, 0.5, 0.85 and 1.0 were prepared by induction melting, ball milling and spark plasma sintering techniques. The thermoelectric properties of the samples were investigated. The XRD analysis indicated that all samples are NaCl-type structure solid solutions Pb(Se,Te) containing nanograins. Increasing Te content resulted in increasing the lattice parameter a. The thermoelectric measurements show that all samples are n-type semiconductors in temperature range from 300 K to 673 K. The electrical resistivity of the doped sample is much smaller than that of pure PbSe, but comparable to that of PbTe. The absolute Seebeck coefficients for the doped sample PbSe_1−xTe_x with x = 0.2, 0.3 and 0.5 range from 150 μV/K at 300 K to 250 μV/K at 673 K, which is much larger than that of pure PbSe (66-138 μV/K), but smaller than that of PbTe (230-310 μV/K) in the same experimental conditions. The thermal conductivity for the doped sample PbSe_1−xTe_x with x = 0.2, 0.3 and 0.5 range from 0.95 to 0.66 W/m K, which is much smaller than that of pure PbSe (2.1-1.3 W/m K) or PbTe (1.4-1.1 W/m K). As a result, the figure of merit for the doped sample can be enhanced. The maximum dimensionless figure of merit ZT of 1.15 was obtained in the sample PbTe_0.5Se_0.5 at 573 K, more than 50% higher than that of pure PbTe prepared in the same condition.     

The nanostructure, wear and corrosion performance of arc-evaporated CrBxNy nanocomposite coatings

The composition, nanostructure, tribological and corrosion behaviour of reactive arc evaporated CrB_xN_y coatings have been studied and compared to CrN. The CrB_xN_y coatings were deposited on a commercial Oerlikon Balzers RCS coating system employing 80:20 Cr:B targets. To vary the composition, the nitrogen fraction was adjusted (N₂ fraction = N₂/(Ar + N₂)) and a moderate bias voltage of − 20 V was applied during coating growth. The coating composition and nanostructure was determined using time-of-flight elastic recoil detection analysis (TOF-ERDA), x-ray diffraction (XRD) and x-ray photoelectron spectroscopy (XPS). Ball-on-disc dry sliding wear tests were conducted using an alumina ball counterface both at room temperature and at 500 °C with the relative humidity controlled at 20%. Potentiodynamic corrosion tests were undertaken in 3.5% NaCl aqueous solution. The wear tracks were examined using optical profilometry and scanning electron microscopy (SEM); the surface composition inside and outside of the wear tracks were investigated using Raman spectroscopy and XPS. All coatings exhibit nanocomposite structures and phase compositions which are in fair agreement with those expected from the equilibrium phase diagram. The lowest wear rate at room temperature and 500 °C was found for CrB_0.14N_1.14, which was shown to exhibit the highest hardness and possesses a nanocomposite nc-CrN/a-BN structure. CrB_0.12N_0.84 coatings showed the lowest passive current density in potentiodynamic corrosion tests.     

Charge ordering analysis by electrical and dielectric measurements in Ca2−xPrxMnO4 (x = 0-0.2) compounds

Ca_2−xPr_xMnO₄ (0 ≤ x ≤ 0.2) polycrystalline ceramic powders were synthesized by sol-gel method. The X-ray diffraction (XRD) profiles were indexed with a tetragonal and orthorhombic structure for Ca₂MnO₄ and Pr-doped compounds, respectively. Electrical properties were investigated by dc and ac electrical measurements. The dc measurements have revealed an insulating state for all compounds in 80-350 K temperature range. Both dc and ac measurements have highlighted a charge ordering (CO) transition at T_CO = 233 and 245 K for x = 0.175 and 0.2, respectively. The CO state was found to be accompanied by a jump of the hopping activation energy and a rapid rise of both dielectric permittivity and imaginary part of ac electrical impedance.     

XPS study of Pr1−xCaxMnO3 (x = 0.2, 0.33, 0.4 and 0.84)

We have studied the Mn 2p, Ca 2p, and Pr 4d core levels of Pr_1-xCa_xMnO₃ (x = 0.2, 0.33, 0.4 and 0.84) as a function of x using X-ray photoelectron spectroscopy both at room temperature as well as 77 K. Suppression of chemical potential shifts have been observed at 77 K compared to that of room temperature spectra. We have discussed this result by considering the concept of phase separation.     

Strong correlation between structural, magnetic and transport properties of non-stoichiometric Sr2FexMo2−xO6 (0.8 ≤ x ≤ 1.5) double perovskites

Sr₂Fe_xMo_2−xO₆ (x = 0.8, 0.9, 1.0, 1.1, 1.2, 1.3, 1.4 and 1.5 wt.%) (SFMO) double perovskite oxides of different compositions have been prepared by sol-gel method. These materials were subjected to X-ray diffraction and found that crystal structure changes from tetragonal to cubic around x = 1.2 wt.%. Lattice parameters and unit cell volume have been calculated using X-ray diffraction data. Magnetization studies have been carried out using Vibrating Sample Magnetometer ranging from −15 kOe to +15 kOe and saturation magnetization (M_s) has been determined. Electrical resistivity and magnetoresistance studies have been carried out in the magnetic field range of −40 kOe to +40 kOe keeping the temperature constant at 5, 150 and 300 K using standard four-probe method. Resistivity studies have also been carried out in the temperature ranging from 5 to 300 K keeping the magnetic field constant at 0, 10, 20 and 40 kOe. Maximum degree of Fe/Mo ordering (η_max) of SFMO has been calculated and compared with magnetic and transport properties. It has been found that there is a strong correlation between 3 parameters η_max, M_s and MR (%), i.e. all of them show a maximum at x = 1.0 wt.% and decreases as x deviates from 1.0 in SFMO. It has been also found that there is a different resistivity behavior between x ≤ 1.2 wt.% and x > 1.2 wt.% samples of SFMO. Semiconductor metal transition temperature was found to be maximum at x = 1.0 wt.%.     

Effect of Ni substitution on the structural and transport properties of NixMn0.8−xMg0.2Fe2O4; 0.0 ≤ x ≤ 0.40 ferrite

Ni_xMn_0.8−xMg_0.2Fe₂O₄; 0.0≤ x ≤0.40 was prepared by standard ceramic technique, presintering was carried out at 900 °C and final sintering at 1200 °C with heating/cooling rate 4 °C/min. X-ray diffraction analyses assured the formation of the samples in a single phase spinel cubic structure. The calculated crystal size was obtained in the range of 75-130 nm. A slight increase in the theoretical density and decrease in the porosity was obtained with increasing the nickel content. This result was discussed based on the difference in the atomic masses between Ni (58.71) and Mn (54.938). IR spectral analyses show four bands of the spinel ferrite for all the samples. The conductivity and dielectric loss factor give nearly continuous decrease with increasing Ni-content. This was discussed as the result of the significant role of the multivalent cations, such as iron, nickel, manganese, in the conduction mechanism. Anomalous behavior was obtained for the sample with x = 0.20 as highest dielectric constant, highest dielectric loss and highest conductivity. This anomalous behavior was explained due to the existence of two divalent cations on B-sites with the same ratio, namely, Mg²⁺ and Ni²⁺.     

Electrochemical hydrogen storage properties of non-stoichiometric La0.7Mg0.3−xCaxNi2.8Co0.5 (x = 0-0.10) electrode alloys

The microstructure and electrochemical hydrogen storage characteristics of La_0.7Mg_0.3−xCa_xNi_2.8Co_0.5 (x = 0, 0.05 and 0.10) alloys prepared by arc-melting and subsequent powder sintering method are investigated. The electrochemical measurement results show that the cycle stability after 100 charge/discharge cycles first increases from 46.4% (x = 0) to 54.3% (x = 0.05), then decreases to 43.2% (x = 0.10), and the high rate dischargeability increases from 64.5% (x = 0) to 68.5% (x = 0.10) at the discharge current density of 1200 mA/g. The electrochemical impedance spectroscopy analysis indicates that the electrochemical kinetics of the alloy electrodes is improved by increasing Ca. The entire results exhibit that a suitable content of Ca (x = 0.05) can improve the overall electrochemical hydrogen storage characteristics of the alloys.     

Part II. Large scale applications of NixMn0.8−xMg0.2Fe2O4; 0.1 ≤ x ≤ 0.35 using laser irradiation

Ni_xMn_0.8−xMg_0.2Fe₂O₄; 0.1 ≤ x ≤ 0.35 was prepared by standard ceramic technique at sintering temperature 1200 °C using heating / cooling rate 4 °C/min. The samples were irradiated by Nd YAG pulsed laser with energy of the pulse 250 mJ. X-ray diffractograms reveal cubic spinel structure for all the samples before and after laser irradiation. After laser irradiation, better crystallinity was obtained in a form of an increase in the calculated crystal size. This increase was discussed as due to the change in the valence of some ions like Fe³⁺, Ni²⁺ and Mn²⁺. The conductivity of all the investigated samples decreases after laser irradiation and becomes temperature independent for a wider range than that before irradiation. This was ascribed to electron rearrangement after laser irradiation. Accordingly, these ferrites are recommended to be useful in electronic devices.     

Magnetocaloric effect in the Ce2Fe17−xMnx helical magnets

The Ce₂Fe_17−xMn_x (x = 0-2) compounds demonstrate a complex temperature dependence of the magnetocaloric effect MCE, which is inverse in a narrow temperature interval just below Néel temperature T_N and normal at higher or lower temperatures. The normal MCE exhibits two peaks in the vicinity of temperatures of ferromagnetic ordering Θ_T and T_N for compositions x = 0-0.35, 1.3-2 or one peak near T_N for antiferromagnets with x = 0.5-1. The maximal change of the peak entropy −S_M is about 3 J/kg K in a field of 5 T for the compounds with x = 0-0.5 at T ∼230 K close to T_N. The drastic decrease of the MCE, by half, in the Ce₂Fe_17−xMn_x system is traceable to a decrease of the spontaneous magnetization and the helical type of magnetic states in the compounds.     

Preparation of CuIn1−xGaxS2 (x = 0.5) flowers consisting of nanoflakes via a solvothermal method

CuIn_1−xGa_xS₂ (x = 0.5) flowers consisting of nanoflakes were successfully prepared by a biomolecule-assisted solvothermal route at 220 °C for 10 h, employing copper chloride, gallium chloride, indium chloride and l-cysteine as precursors. The biomolecule l-cysteine acting as sulfur source was found to play a very important role in the formation of the final product. The diameter of the CuIn_0.5Ga_0.5S₂ flowers was 1-2 μm, and the thickness of the flakes was about 15 nm. The obtained products were characterized by X-ray diffraction (XRD), energy dispersion spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction spectroscopy (SAED), and UV-vis absorption spectroscopy. The influences of the reaction temperature, reaction time, sulfur source and the molar ratio of Cu-to-l-cysteine (reactants) on the formation of the target compound were investigated. The formation mechanism of the CuIn_0.5Ga_0.5S₂ flowers consisting of flakes was discussed.