Ultra-high elevated temperature strength of TiB2-based ceramics consolidated by spark plasma sintering

Spark plasma sintering of TiB₂–boron ceramics using commercially available raw powders is reported. The B₄C phase developed during reaction-driven consolidation at 1900 °C. The newly formed grains were located at the grain junctions and the triple point of TiB₂ grains, forming a covalent and stiff skeleton of B₄C. The flexural strength of the TiB₂–10 wt.% boron ceramic composites reached 910 MPa at room temperature and 1105 MPa at 1600 °С. Which is the highest strength reported for non-oxide ceramics at 1600 °C. This was followed by a rapid decrease at 1800 °C to 480–620 MPa, which was confirmed by increased number of cavitated titanium diboride grains observed after flexural strength tests.     

Fracture and property relationships in the double diboride ceramic composites by spark plasma sintering of TiB2 and NbB2

Bulk titanium diboride–niobium diboride ceramic composites were consolidated by spark plasma sintering (SPS) at 1950°C. SPS resulted in dense specimens with a density exceeding 98% of the theoretical density and a multimodal grain size ranging from 1 to 10 μm. During the SPS consolidation, the pressure was applied and released at 1950 and 1250°C, respectively. This allowed obtaining a two-phase composite consisting of TiB₂ and NbB₂. For these ceramics composites, we evaluated the flexural strength and fracture toughness and room and elevated temperatures. Room-temperature strength of thus produced bulks was between 300 and 330 MPa, at 1200°C or 1600°C an increase in strength up to 400 MPa was observed. Microstructure after flexure at elevated temperatures revealed the appearance of the needle-shape subgrains of NbB₂, an evidence for ongoing plastic deformation. TiB₂–NbB₂ composites had elastic loading stress curves at 1600°C, and at 1800°C fractured in the plastic manner, and strength was ranged from 300 to 450 MPa. These data were compared with a specimen where a (Ti,Nb)B₂ solid solution was formed during SPS to explain the behavior of TiB₂–NbB₂ ceramic composites at elevated temperatures.     

High‐Temperature Strength of Boron Suboxide Ceramic Consolidated by Spark Plasma Sintering

The spark plasma sintering (SPS) of B₆O ceramics using a highly crystalline boron suboxide powder with a low oxygen deficiency level is reported. The monolithic boron suboxide ceramic exhibited a room‐temperature strength of 300 ± 20 MPa, which is comparable to the strength of monolithic boron carbide. With increasing flexural test temperature, the strength of the boron suboxide ceramics increased to 450 MPa at 1400°C. The increase in strength with the temperature is associated with the unique microstructure of boron suboxide grains, which allows intergranular “brittle” fracture along subgrains even at 1400°C. This suggests that even higher strengths can be achieved.     

Effect of titanium diboride on the homogeneity of boron carbide ceramic by flash spark plasma sintering

A novel method, namely flash spark plasma sintering (FSPS), combining flash sintering and electric field assisted sintering, was utilized to densify boron carbide/titanium diboride (B₄C/TiB₂) composites. Further, sintering homogeneity of the composites with different contents of TiB₂ was systematically investigated and theoretical model was built. Results indicated that addition of 50?wt% TiB2 led to the densification of B₄C/TiB₂ composite by up to 97.7% with regional range 1.9% at 1872?°C under pressure of 4?MPa in 60?s. The preferential pathway of TiB₂ network proves to disperse the central current and distribute thermal flow throughout the specimen possibly via tunneling, electronic field emission effect at first stage and lower-resistance composite pathway latter, contributing to the increased homogeneity.     

Power-controlled flash spark plasma sintering of gadolinia-doped ceria

Electric field-assisted sintering (FAST) is a rapidly growing scientific and engineering domain. In the present paper, we describe the process of flash sintering (FS) in a configuration of classical spark plasma sintering (SPS) (graphite punch and boron nitride (BN) die), also called flash spark plasma sintering (FSPS). The densification process of Gd_0.1Ce_0.9O_2-x powder is studied in detail with a focus on the transition from FAST to FS. We discuss the electrical, geometrical, and thermal evolution of the process and the characteristics of the final compacts. Low electrical fields are sufficient for the onset of FS. Ceria is a material difficult to sinter by FAST techniques due to its known mechanochemical transformations. We observed the disintegration of pellets after experiments with well-pronounced flash event.     

Consolidation by spark plasma sintering of polyimide and polyetheretherketone

This article presents two high‐temperature thermoplastic powders which were sintered by spark plasma sintering in order to get homogeneous mechanical properties. Dense polyimide (PI) and polyetheretherketone (PEEK) specimens were obtained at temperatures as low as 320°C for PI and 200°C for PEEK, respectively. Relative densities higher than 99% were reached for both materials. In order to characterize their properties, in situ measurements with compression and hardness tests were carried out on sintered samples. This method allowed to obtain polymeric materials with improved mechanical properties. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40783.     

Microstructure and flexural strength of hafnium diboride via flash and conventional spark plasma sintering

Microstructure evolution in bulk hafnium diboride ceramics prepared by spark plasma sintering in flash regime was compared with conventional spark plasma sintering. The conventional and flash spark plasma sintering resulted in ceramics with a high relative density exceeding 96% of their theoretical density. A remarkably fine grain size distribution was noticed for the specimen prepared in the flash regime. This atypical microstructure evolution provides a possible insight into the mechanism of flash sintering for conductive bulks. The room temperature flexural strength of the hafnium diboride processed by flash SPS was 650 MPa which is 140 MPa higher than the sample produced by conventional SPS.     

Thermochemical model on the carbothermal reduction of oxides during spark plasma sintering of zirconium diboride

Carbon was used to reduce oxides in spark plasma sintered ZrB₂ ultra-high temperature ceramics. A thermodynamic model was used to evaluate the reducing reactions to remove B₂O₃ and ZrO₂ from the powder. Powder oxygen content was measured and carbon additions of 0.5 and 0.75 wt% were used. A C–ZrO₂ pseudo binary diagram, ZrO₂–B₂O₃–C pseudo ternaries, and Zr–C–O potential phase diagrams were generated to show how the reactions can be related to an open system experiment in the tube furnace. Scanning transmission electron microscopy identified impurity phases composed of amorphous Zr–B–O with lamellar BN and a Zr–C–O ternary model was calculated under SPS sintering conditions at 1900°C and 6 Pa to understand how oxides can be retained in the microstructure.     

High‐temperature mechanical behavior of ZrB2‐based composites with micrometer‐ and nano‐sized SiC particles

Using micrometer‐ and nano‐sized SiC particles as reinforcement phase, two ZrB₂‐SiC composites with high strength up to 1600°C were prepared using high‐energy ball milling, followed by hot pressing. The composite microstructure comprised finer equiaxed ZrB₂ and SiC grains and intergranular amorphous phase. The temperature dependency of flexure strength related to the initial particle size of SiC. In the case of micrometer‐sized SiC, the high‐temperature strength was improved up to 1500°C compared to room‐temperature strength, but the strength degraded at 1600°C, with strength values of 600‐770 MPa. In the case of nano‐sized SiC, the enhanced high‐temperature strength was observed up to 1600°C, with strength values of 680‐840 MPa.     

In-situ graphene platelets formation and its suppression during reactive spark plasma sintering of boron carbide/titanium diboride composites

Boron carbide composites with 10 vol.% TiB₂ were prepared by reactive sintering of B₄C, TiO₂, and carbon black powder mixture at the temperature of 1800 °C, under a pressure of 70 MPa in a vacuum. The combined effects of electric current and in-situ reactions led to a significant overheating of the central part of the sample, while no overheating was observed for hot press and non-reactive SPS processes. A lower electrical resistivity of TiB₂ produced a significant Joule heating of boron carbide, leading to its partial decomposition to form gaseous boron and graphene platelets. Homogenous, fully dense and graphene-free samples were obtained when employing an insulating Al₂O₃ paper during reactive SPS. A short dwell time (30 s after a degassing step of 6 min) and the uniform distribution of fine TiB₂ grains were the main advantages of isolated SPS over the reactive hot press and SPS processes, respectively.     

High‐Strength B4C–TaB2 Eutectic Composites Obtained via In Situ by Spark Plasma Sintering

The in situ synthesis/consolidation of B₄C–TaB₂ eutectic composites by spark plasma sintering (SPS) is reported. Samples for the evaluation of bending strength were cut from specimens with diameters of 30 mm. The sample prepared for the three‐point flexural strength test had fibers of tantalum diboride with diameter of 1.3 ± 0.4 μm distributed in the B₄C matrix, thereby reducing composites brittleness and yielding an indentation fracture toughness of up to 4.5 MPa·m^1/2. Furthermore, the Vickers hardness of B₄C–TaB₂ eutectics formed by SPS was as high as 26 GPa at an indentation load of 9.8 N. The flexural strength of the B₄C–TaB₂ system has been reported for the first time. Some steps were identified in the load–displacement curve, suggesting that micro‐ and macrocracking occurred during the flexural test. Ceramic composites with a eutectic structure exhibited a room‐temperature strength of 430 ± 25 MPa. Compared with other eutectic composites of boron carbide with transition‐metal diborides, room‐temperature strength the B₄C–TaB₂ was 40% higher than that of B₄C–TiB₂ ceramics, demonstrating advantage of the in situ synthesis/consolidation of eutectic composites by SPS.     

Solid solution synthesis of tantalum carbide‐hafnium carbide by spark plasma sintering

Solid solutions of Tantalum carbide (TaC) and Hafnium carbide (HfC) were synthesized by spark plasma sintering. Five different compositions (pure HfC, HfC‐20 vol% TaC, HfC‐ 50 vol% TaC, HfC‐ 80 vol% TaC, and pure TaC) were sintered at 1850°C, 60 MPa pressure and a holding time of 10 min without any sintering aids. Near‐full density was achieved for all samples, especially in the HfC‐contained samples. The porosity in pure TaC samples was caused by the oxygen contamination (Ta₂O₅) on the starting powder surface. The addition of HfC increased the overall densification by transferring the oxygen contamination from TaC surface and forming ultrafine HfO₂ and Hf‐O‐C grains. With the increasing HfC concentration, the overall grain size was reduced by 50% from HfC‐ 80 vol% TaC to HfC‐20 vol% TaC sample. The solid solution formation required extra energy, which restricted the grain growth. The lattice parameters for the solid solution samples were obtained using X‐ray diffraction which had an excellent match with the theoretical values computed using Vegard's Law. The mechanical properties of the solid solution samples outperformed the pure TaC and HfC carbides samples due to the increased densification and smaller grain size.     

Synthesis of YB2C2 by high-energy ball milling and reactive spark plasma sintering

X-ray pure yttrium diborodicarbide (YB₂C₂) was synthesized for the first time via modified spark plasma sintering (SPS) using Y₂O₃, B₄C, and carbon as starting materials. Homogeneous intermixing of the raw powder by high energy ball milling (HEBM) promoted the formation of YB₂C₂ powder with layered structure by boro/carbo-thermal reduction. The average particle size of the synthesized powder at an optimum synthesis temperature (1625℃) was 568 nm. Small amount of YB₂C was formed by consuming YB₄ at and above 1625°C. The metal basis purity of the synthesized YB₂C₂ powder was 99.84%. X-ray pure YB₂C₂ was obtained by densifying the synthesized YB₂C₂ powder at 1900°C for 60 minutes at a pressure of 80 MPa using SPS. This study reports a simple method for the fabrication of X-ray pure rare earth metal diborodicarbides (ReB₂C₂).     

Synthesis of dense NiZn ferrites by spark plasma sintering

Dense NiZn ferrites were fabricated by spark plasma sintering (SPS) at 900 °C and 20 MPa in short periods. The powder was densified to 98% of the theoretical density by the SPS process. The SPS disks exhibited a higher saturation magnetization (Ms), up to 272 emu/cm³, than did the disks sintered by the conventional process. A higher coercivity (Hci) was obtained when the green bodies were sintered by the SPS process for 5 min. A modest holding time is essential to obtain fine grain and uniformity in the SPS process. Secondary crystallization, inhomogeneous microstructure and intragranular pores were found as a result of the rapid sintering and relatively longer holding time in the SPS process. Infrared (IR) spectra were also measured in the range from 350 to 700 cm⁻¹ to study the efforts of the SPS process on NiZn ferrites.     

Electrical properties of reduced 3YTZP ceramics consolidated by spark plasma sintering

3 mol% Yttria doped zirconia ceramics were consolidated by spark plasma sintering (SPS) at two sintering temperatures with the aim of achieving two different reduction levels. Microstructural characterization of the ceramics was performed by scanning electron microscopy (SEM). Electrical properties were investigated by means of impedance spectroscopy from room temperature up to 500 °C. The two ceramics presented a remarkably different electrical behavior. The effect of the extra electrons introduced by reduction during SPS on both the bulk and the grain boundary conductivity was analyzed and discussed.     

Consolidation by spark plasma sintering (SPS) of polyetheretherketone

The present study deals with the consolidation of an ultra‐high performance polymer, the poly(ether ether ketone) (PEEK), for structural applications, using the powder metallurgy (PM) way, and more precisely the Spark Plasma Sintering (SPS) processing. The effects of SPS parameters such as temperature, pressure, and dwell time on density and mechanical properties of PEEK were investigated via a Design of Experiments (DoE). A temperature of 250 °C, a pressure of 40 MPa, and a dwell time of 20 min have been identified as the optimal SPS process parameters. In these conditions, a density of 1.31 g / cm³ was reached and homogeneous mechanical properties in the volume determined by means of compression tests were found with a compressive modulus of 2.75 GPa, a yield strength of 134 MPa, and a maximum compressive strain of 43%. These results are better than those of commercial products obtained by injection molding. The pressure appears to be a significant parameter on PEEK properties and plays positive or negative roles according to the responses of DoE studied. To our knowledge, it is one of the first studies based on the application of the PM techniques for PEEK consolidation showing the possibility to process below its melting point. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44911.     

Impact of spark plasma sintering (SPS) on mullite formation in porcelains

The effect of the spark plasma sintering (SPS) process on mullite formation in porcelains was studied using X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. SPS affected the kinetics and morphology of formed mullite. After sintering at 1100°C, unlike conventional sintering, SPS promoted the formation of mullite due to the combination of vacuum and applied pressure. Mullite crystal growth was altered by the atmosphere (vacuum), dwell time (0‐15 minutes), and temperature (1000‐1200°C). The applied pressure caused the mullite needles to orient perpendicular to the direction of the applied load. Depending on SPS dwell time, the mullite formed after sintering at 1100°C also had different crystal structure (tetragonal for short dwell time of 0‐5 minutes and orthorhombic for a long dwell time of 10‐15 minutes). Dissolution of mullite was observed at 1100°C by extending the dwell time by up to 15 minutes and the dissolved mullite reprecipitated on the small needles (~40 nm) and coarsened via Oswald ripening resulting in larger mullite needles (~60 nm).     

CMAS corrosion behavior of a LaPO4 ceramic prepared by spark plasma sintering

At high temperatures in gas turbines, traditional yttria stabilized zirconia materials fail prematurely owing to CMAS (calcium–magnesium–alumina–silicate) corrosion. Thus, new materials need to be developed urgently. In this study, LaPO₄ powder was synthesized by chemical coprecipitation and heat treatment using lanthanum nitrate (La(NO₃)₃∙6H₂O) and ammonium dihydrogen phosphate (NH₄H₂PO₄) as starting materials, and LaPO₄ bulk was prepared by spark plasma sintering. The surface of the LaPO₄ bulk was coated with CMAS (CaO–MgO–Al₂O₃–SiO₂) powder, and the CMAS interaction with the LaPO₄ bulk at different temperatures was investigated. The phase and microstructure of the LaPO₄ powder and bulk, as well as the CMAS corrosion products, were characterized using X-ray diffraction and scanning electron microscope. The superior CMAS resistance of the LaPO₄ bulk was attributed to the low wettability of LaPO₄ by the CMAS melt and the development of dense layers of new corrosion products, which effectively protected the LaPO₄ bulk from CMAS infiltration.     

Fabrication of translucent AlN ceramics with MgF2 additive by spark plasma sintering

Translucent AlN ceramics with 0‐2 wt.% MgF₂ additive were prepared by spark plasma sintering. AlN powder was heated temporarily up to 2000°C, before holding at 1850°C for 20 minutes in N₂ gas. The sintered ceramics consisted of a single phase of hexagonal AlN, and showed a transgranular fracture mode. The total transmittance was improved remarkably by the additive, to reach 74% at a wavelength of 800 nm for 1 wt.% MgF₂. For 2 wt.% MgF₂, the transmittance was slightly lower than that for 1 wt.% MgF₂, and an absorption band was observed apparently at around 400 nm. The addition of MgF₂ along with the temporary heating at higher temperatures than the sintering temperature contributed to improve the transmittance remarkably.     

Densification behaviour and physico-mechanical properties of porcelains prepared using spark plasma sintering

Porcelain powder was consolidated using spark plasma sintering (SPS) at a constant heating rate of 100°C?min^?1 to peak temperatures ranging from 1000 to 1200°C and was observed to sinter at relatively low temperature ～920°C under the SPS conditions while conventional sintering requires ～1050°C. SPS produced densification rates about 10 times greater than conventional sintering. The dwelling step at the optimal peak temperature was negligible due to rapid flow of the molten glass assisted by applied pressure. SPSed samples exhibited denser microstructures, resulting in improved physico-mechanical properties compared with conventionally sintered samples such as apparent bulk density improved from 2.38 to 2.48?g?cm^?3, Vickers hardness improved from 3–5 to 6–7?GPa, and fracture toughness improved from 2–3 to 4–6?MPa?m^1/2.