Dielectric and Raman Spectroscopic Studies of Na0.5Bi0.5TiO3–BaSnO3 Ferroelectric System

A series of lead‐free perovskite solid solutions of (1 ? x) Na_0.5Bi_0.5TiO₃(NBT)—x BaSnO₃(BSN), for 0.0 ≤ x ≤ 0.15 have been synthesized using a high‐temperature solid‐state reaction route. The phase transition behaviors are studied using dielectric and Raman spectroscopic techniques. The ferroelectric to relaxor phase transition temperature (T_FR) and the temperature corresponding to maximum dielectric permittivity (T_m) are estimated from the temperature‐dependent dielectric data. Dielectric studies show diffuse phase transition around ~335°C in pure NBT and this transition temperature decreases with increase in x. The disappearance of x‐dependence of A₁ mode frequency at ~134 cm^?1 for x ≥ 0.1 is consistent with rhombohedral‐orthorhombic transition. In situ temperature dependence Raman spectroscopic studies show disappearance and discontinuous changes in the phonon mode frequencies across rhombohedral (x < 0.1)/orthorhombic (x ≥ 0.1) to tetragonal transition.     

High electrocaloric effect in hot‐pressed Pb0.85La0.1(Zr0.65Ti0.35)O3 ceramics with a wide operating temperature range

The temperature stability of the electrocaloric effect (ECE) in relaxor ferroelectric Pb_0.85La_0.1(Zr_0.65Ti_0.35)O₃ (PLZT) prepared by the hot‐press sintering method has been investigated. Compared to the PLZTs prepared via the conventional sintering process, the hot‐pressed PLZTs exhibit larger ECE and superior temperature stability. The hot‐pressed sample with an appropriate content of excess PbO presents a high ΔT of 2.4°C and ΔS of 2.3 J kg^?1·K^?1, both of which are 30% greater than those of the conventionally sintered samples measured at 100 kV·cm^?1. More importantly, the hot‐pressed specimens display great stable electrical properties, including the dielectric breakdown strength and electrical resistivity in the temperature range from 0°C to 100°C, whose ECE instability, especially, is only one‐half that of the samples prepared by the conventional solid‐state method. In addition, the ECE and its stability of the hot‐pressed sample can be further enhanced by increasing the operating electric field to a relatively high level of 200 kV·cm^?1. This work demonstrates hot‐press sintering is an effective method to fabricate ferroelectric ceramics with high ECE as well as desirable temperature stability.     

Large Strain Response and Fatigue‐Resistant Behavior in Ternary Bi0.5Na0.5TiO3–BaTiO3–Bi(Zn0.5Ti0.5)O3 Solid Solutions

A ternary solid solution (1 ? x)(0.88Bi_0.5Na_0.5TiO₃–0.12BaTiO₃)‐xBi(Zn_0.5Ti_0.5)O₃ (BNBZT, BNBZTx) was designed and fabricated using the traditional solid‐state reaction method. The temperature and composition dependence of dielectric, ferroelectric, piezoelectric, and fatigue properties were systematically investigated and a schematic phase diagram was proposed. The substitution with Bi(Zn_0.5Ti_0.5)O₃ was found to shift the phase transition (ferroelectric tetragonal to relaxor pseudocubic phase) to lower temperatures. At a critical composition x of 0.05, large electric‐field‐induced strain response with normalized strain S_max/E_max as high as 526 pm/V was obtained under a moderate field of 4 kV/mm around room temperature. The strain exhibited good temperature stability within the temperature range of 25°C–120°C. In addition, excellent fatigue‐resistant behavior was observed in the proposed BNBZT solid solution after 10⁶ bipolar cycles. These give the BNBZT system great potential as environmental friendly solid‐state actuator.     

Temperature‐insensitive strain behavior in 0.99[(1−x)Bi0.5(Na0.80K0.20)0.5TiO3−xBiFeO3]–0.01Ta lead‐free piezoelectric ceramics

Lead‐free 0.99[(1?x)Bi_0.5(Na_0.80K_0.20)_0.5TiO₃?xBiFeO₃]–0.01Ta (BNKT20–100xBF–1Ta) lead‐free piezoelectric ceramics were fabricated through conventional solid state sintering method. Results showed that change of BF content in the BNKT20–100xBF–1Ta induced a phase transition from ferroelectric to ergodic relaxor phase with a significant disruption of the long‐range ferroelectric order. A large electric‐field‐induced strain of 0.36% (at 80 kV/cm driving field, corresponding to a large signal of ~450 pm/V) which is derived from a reversible field‐induced ergodic relaxor to ferroelectric phase transformation, was obtained in the composition with x=0.01 near the ferroelectric‐ergodic relaxor phase boundary. Moreover, an attractive property for application in nonlinear actuators demanding enhanced thermal stability was obtained in this material, which showed a temperature‐insensitive strain characteristic in the temperature range from room temperature to 100°C.     

Composition‐ and Temperature‐Dependent Large Strain in (1−x)(0.8Bi0.5Na0.5TiO3–0.2Bi0.5K0.5TiO3)– xNaNbO3 Ceramics

Ternary solid solutions of (1 ? x)(0.8Bi_0.5Na_0.5TiO₃–0.2Bi_0.5K_0.5TiO₃)– xNaNbO₃ (BNKT–xNN) lead‐free piezoceramics were fabricated using a conventional solid‐state reaction method. Pure BNKT composition exhibited an electric‐field‐induced irreversible structural transition from pseudocubic to ferroelectric rhombohedral phase at room temperature. Accompanied with the ferroelectric‐to‐relaxor temperature T_F‐R shifted down below room temperature as the substitution of NN, a compositionally induced nonergodic‐to‐ergodic relaxor transition was presented, which featured the pinched‐shape polarization and sprout‐shape strain hysteresis loops. A strain value of ~0.445% (under a driving field of 55 kV/cm) with large normalized strain of ~810 pm/V was obtained for the composition of BNKT–0.04NN, and the large strain was attributed to the reversible electric‐field‐induced transition between ergodic relaxor and ferroelectric phase.     

Enhanced electrocaloric response and energy storage performance of Li-substituted BaTiO3 ceramics

Recently, ferroelectric and antiferroelectric ceramic materials have gained a lot of interest for the development of environment-friendly highly-efficient electrocaloric refrigeration and energy-storage devices. In this work, lead-free Ba_1−xLi_xTiO₃ ceramics with x = 0, 0.01, 0.02, 0.03, 0.04, and 0.05 were synthesized by the conventional solid-state reaction method, and the effect of Li doping on dielectric, leakage current, ferroelectric, electrocaloric, and energy storage properties of BaTiO₃ ceramics was systematically investigated. The XRD and Raman studies confirmed that the structure of Ba_1−xLi_xTiO₃ remains tetragonal as for BaTiO₃. The Li substitution shifted the phase transition (T_C) of BaTiO₃ slightly towards the lower temperature side. Significant drop in leakage current was observed with an addition of Li content. The maximum values of the electrocaloric effect (ΔT), electrocaloric responsivity, and coefficient of performance were found to be 1.44 K, 0.24 × 10⁻⁶ K m/V, and 5.75, respectively, for x = 0.04 at an applied field of 60 kV/cm near the Curie temperature. The maximal value of energy storage density was found to be 0.42 J/cm³ with an energy storage efficiency of 60% for x = 0.05. Our results suggested that lead-free Ba_1−xLi_xTiO₃ ceramic material is a promising candidate for potential applications in solid-state refrigeration technology and high-efficiency energy storage devices.     

Electrocaloric effect and pyroelectric performance in (K,Na)NbO3-based lead-free ceramics

The issue of how to achieve an electrocaloric effect (ECE) and pyroelectric effect in a material simultaneously remains to be a challenge for developing practical solid-state cooling devices and RF-detectors. Here, we structure a polymorphic phase transition (PPT) region by doping modification in KNN-based ceramics, which are developed to achieve the ECE. The direct measured ECE and pyroelectric properties are investigated in lead-free (1-x)K_0.5Na_0.5NbO₃-xBi_0.5Na_0.5ZrO₃ (KNN-xBNZ) ceramics. The adiabatic temperature change (∆T) of 0.22 K at 100°C, 0.14 K at 70°C and 0.16 K at 30°C can be obtained under an electric field of 35 kV cm^–1 for x = 0.03, 0.04 and 0.05, respectively. In addition, the temperature dependence of pyroelectric coefficient (p) is established for all compositions via the Byer-Roundy method. A large p of 454.46 × 10^–4 C m^–2 K^–1 is detected at Curie temperature (T_C) in the ceramics with x = 0.03. Achieving electrocaloric effect and pyroelectric performance simultaneously may shed light and provide a feasible design scheme for developing practically useful electrocaloric and pyroelectric materials.     

Structure,dielectric, electrostrictive and electrocaloric properties of environmentally friendly Bi-substituted BCZT ferroelectric ceramics

In this study, environmentally friendly Bi-substituted [(Ba_0.85Ca_0.15)_1-3x/2Bi_x](Zr_0.1Ti_0.9)O₃ (BCZT-xBi) ferroelectric ceramics with x = 0–0.08 were prepared using a solid-state sintering method. The structures, dielectric, electrostrictive and electrocaloric properties of the Bi-substituted BCZT ceramics were thoroughly investigated. With an increase in the Bi³⁺ content, the temperature corresponding to the maximum permittivity (T_m) decreased monotonously. Meanwhile, the broadening of the dielectric peaks and the increase in the relaxation coefficient of the ceramics transformed their typical ferroelectric-to-paraelectric phase transition to diffuse phase transition (DPT). This was further confirmed by the trends shown by the ferroelectric properties of the ceramics. The current peak intensity in current-electric field (I-E) curves decreased with an increase in x and finally became constant, indicating that domain reversal disappeared gradually. High electrostrictive coefficient Q₃₃ values of 0.0307, 0.0299 and 0.0223 m⁴/C² were obtained for the ceramics with x = 0.02, 0.04 and 0.06 respectively. The Q₃₃ values of the ceramics indicated their temperature-insensitive nature over the temperature range of 30–120 °C. Although the maximum value of the electrocaloric adiabatic temperature change (ΔT) (0.91 K) was achieved at x = 0.02, the thermally stability of ΔT is improved with an increase in x from 0.02 to 0.06. The results indicated that x = 0.06 improved the thermal stability of the electrostrictive and electrocaloric performance. By increasing the driving field strength, better electrostrictive and electrocaloric responses could be achieved.     

Large electrocaloric responses in [Bi1/2(Na,K)1/2]TiO3‐based ceramics with giant electro‐strains

The electrocaloric effect (ECE) is investigated through indirect measurement in two lead‐free [Bi_1/2(Na,K)_1/2]TiO₃‐based ceramics that were previously reported to display giant electro‐strains. In the Nb‐doped ceramic, denoted as BNKT‐2.5Nb, a decent temperature change of ΔT=1.85 K and an electrocaloric responsivity of ΔT/ΔE=0.37 (10^?6Km V^?1) are found around room temperature (32°C). While in the Ta‐doped ceramic, BNKT‐1.5Ta, a wide operation temperature range (T_span ~55 K) is observed near room temperature. Additional electrical measurements, as well as transmission electron microscopy experiments, are performed to identify the mechanisms of the ECE in both ceramics.     

Physical Properties of La1−xEuxPO4,0 ≤ x ≤ 1, Monazite‐Type Ceramics

Synthetic La_1?xEu_xPO₄ monazite‐type ceramics with 0 ≤ x ≤ 1 have been characterized by ultrasound techniques, dilatometry, and micro‐calorimetry. The coefficients of thermal expansion and the elastic properties are, to a good approximation, linearly dependent on the europium concentration. Elastic stiffness coefficients range from 182(1) to 202(1) GPa for c₁₁ and from 53.8(7) to 61.1(4) GPa for c₄₄. They are strongly dependent on the density of the sample. The coefficient of thermal expansion at 673 K is 8.4(3)  × 10^?6 K^?1 for LaPO₄ and 9.9(3)  × 10^?6 K^?1 for EuPO₄, respectively. The heat capacities at ambient temperature are between 101.6(8) J·(mol·K)^?1 for LaPO₄ and 110.1(8) J·(mol·K)^?1 for EuPO₄. The difference between the heat capacity of LaPO₄ and the Eu‐containing solid solutions is dominated by electronic transitions of the 4f‐electrons at temperatures above 75 K.     

Enhanced pyroelectric properties in (Bi0.5Na0.5)TiO3–BiAlO3–NaNbO3 ternary system lead‐free ceramics

High pyroelectric performance and good thermal stability of pyroelectric materials are desirable for the application of infrared thermal detectors. In this work, enhanced pyroelectric properties were achieved in a new ternary (1?x)(0.98(Bi_0.5Na_0.5)(Ti_0.995Mn_0.005)O₃–0.02BiAlO₃)–xNaNbO₃ (BNT–BA–xNN) lead‐free ceramics. The effect of NN addition on the microstructure, phase transition, ferroelectric, and pyroelectric properties of BNT–BA–xNN ceramics were investigated. It was found that the average grain size decreased as x increased to 0.03, whereas increased with further NN addition. The pyroelectric coefficient p at room temperature (RT) was significantly increased from 3.87 × 10^?8Ccm^?2K^?1 at x = 0 to 8.45 × 10^?8Ccm^?2K^?1 at x = 0.03. The figures of merit (FOMs), F_i, F_v and F_d, were also enhanced with addition of NN. Because of high p (7.48 × 10^?8Ccm^?2K^?1) as well as relatively low dielectric permittivity (~370) and low dielectric loss (~0.011), the optimal FOMs at RT were obtained at x = 0.02 with F_i = 2.66 × 10^?10 m/V, F_v = 8.07 × 10^?2 m²/C, and F_d = 4.22 × 10^?5 Pa^?1/2, which are superior to other reported lead‐free ceramics. Furthermore, the compositions with x ≤ 0.03 exhibited excellent temperature stability in a wide temperature range from 20 to 80°C because of high depolarization temperature (≥110°C). Those results unveil the potential of BNT–BA–xNN ceramics for infrared detector applications.     

Novel BiFeO3–BaTiO3–Ba(Mg1/3Nb2/3)O3 Lead‐Free Relaxor Ferroelectric Ceramics for Energy‐Storage Capacitors

A novel lead‐free relaxor ferroelectric ceramic of (0.67?x)BiFeO₃–0.33BaTiO₃–xBa(Mg_1/3Nb_2/3)O₃ [(0.67?x)BF–0.33BT–xBMN, x = 0–0.1] was prepared by a solid‐state reaction method. A relatively high maximum polarization P_max of 38 μC/cm² and a low remanent polarization P_r of 5.7 μC/cm² were attained under 12.5 kV/mm in the x = 0.06 sample, leading to an excellent energy‐storage density of W ~1.56 J/cm³ and a moderate energy‐storage efficiency of η ~75%. Moreover, a good temperature stability of the energy storage was obtained in the x = 0.06 sample from 25°C to 190°C. The achievement of these characteristics was basically attributed to an electric field induced reversible ergodic to ferroelectric phase transition owing to similar free energies near a critical freezing temperature. The results indicate that the (0.67?x)BF–0.33BT–xBMN lead‐free realxor ferroelectric ceramic could be a promising dielectric material for energy‐storage capacitors.     

Preparation and Electric Properties of Bi0.5Na0.5TiO3–Bi(Al0.5Ga0.5)O3 Lead‐Free Piezoceramics

A new lead‐free BNT‐based piezoelectric ceramics of (1 ? x)Bi_0.5Na_0.5TiO₃–xBi(Al_0.5Ga_0.5)O₃ (x = 0, 0.02, 0.03, 0.04, and 0.05) were synthesized using a conventional ceramic fabrication method. Their structures and electrical properties were investigated. All the samples show a typical ferroelectric P(E) loops and S(E) curves at room temperature. The optimal properties are obtained at the composition of the x = 0.03. The substitution of Bi(Al_0.5Ga_0.5)O₃ enhances piezoelectric constant and increases Curie temperature from 58 pC/N and 310°C of pure BNT to 93 pC/N and 325°C of the x = 0.03. The temperature‐dependent P(E) loops and S(E) curves of 0.97BNT–0.03BAG indicate that phase transition from ferroelectric to antiferroelectric takes place over a very wide temperature region from 80°C to 180°C. The results show that the introduction of BAG improves the electrical properties of BNT.     

Dielectric properties and electrocaloric effect of yttrium-modified BaTiO3 ceramics

The electrocaloric effect (ECE) is a promising candidate to replace the vapor-compression cooling technology, which has reached its end of improving the energy utilization efficiency. In the present work, the Y-modified BaTiO₃ ceramics with nominal compositions of Ba(Ti_1-xY_x)O₃ (abbreviated as BT-100xY, where x = 0.0125, 0.025, 0.0375, 0.050 and 0.0625) have been prepared through the conventional solid-state reaction sintering method. The dielectric properties and electrocaloric effect of BT-100xY ceramics have been investigated in detail. The XRD patterns indicate that all the BT-100xY ceramics possess pure perovskite structure without secondary phases. The temperature dependence of dielectric permittivity reveals that the BT-1.25Y, 2.5Y, 3.75Y and 5.0Y are normal ferroelectrics, and the BT-6.25Y is a relaxor ferroelectric. The ECE is calculated through the indirect equation based on Maxwell relation. The BT-2.5Y exhibits the largest ΔT = 1.26 K and the largest ΔS = 1.68 J/kg · K among all the BT-100xY ceramics, and the BT-2.5Y also exhibits the largest ΔT/ΔE = 0.296 × 10^?6 K · m/V and the largest ΔS/ΔE = 0.394 × 10^?6 J · m/kg · K?V. The ECE in our work is comparable with or even larger than that of BaTiO₃-based ceramics previously reported, which indicates that the BT-100xY ceramics are promising ECE materials.     

Pyroelectric energy harvesting using low–TC (1–x)(Ba0.7Ca0.3)TiO3–xBa(Zr0.2Ti0.8)O3 bulk ceramics

Lead‐free ferroelectric ceramics (1–x)(Ba_0.7Ca_0.3)TiO₃–xBa(Zr_0.2Ti_0.8)O₃ (BCTZ100x) with x = 0.20, 0.30, 0.40, 0.50, 0.60, 0.70, and 0.80 were evaluated for their pyroelectric energy harvesting performance, using the Olsen cycle. As the composition ratio x increased, the crystal phase changed to tetragonal, orthorhombic, rhombohedral, and cubic; the phase boundaries crossed each other in the vicinity of BCTZ70. The crossover phase transition behavior between first‐order and diffuse phase transition changed to only the diffusion phase transition with increasing x. A pinching effect occurred because an increase in dielectric constant was also observed. Energy densities N_D of 229 mJ/cm³ and 256 mJ/cm³ for BCTZ50 and BCTZ80 were obtained, respectively, in temperature of 30°C‐100°C and an electric field of 0‐30 kV/cm. These N_D values are over two times higher than that of soft–Pb(Ti,Zr)O₃ (PZT), which exhibits piezoelectric performance equivalent to BCTZ50 at room temperature. Compared with soft–PZT, BCTZ50 and BCTZ80 exhibited larger N_D values owing to their lower Curie temperatures (T_C ~ 50°C‐110°C). We conclude that low–T_C ferroelectrics are useful for pyroelectric energy conversion based on the Olsen cycle even if they are unsuitable for piezoelectric applications at high temperatures.     

Temperature and Frequency Dependence of Electric Field‐Induced Phase Transitions in PMN–0.32PT

Single crystal (1 ? x)Pb(Mg_1/3 Nb_2/3)O₃–xPbTiO₃ [PMN–xPT] (x = 0.32) is a relaxor‐ferroelectric material known to exhibit ‘giant’ piezoelectric behavior, with achievable strains in excess of 1% for samples of certain particular crystallographic orientations and chemical compositions close to the morphotropic phase boundary. In this study, we investigate the electric field‐induced structural phase transitions in single crystal PMN–0.32PT with time‐of‐flight neutron diffraction and macroscopic electrical polarization measurements, and show that both the frequency of the applied ac field and the temperature of the sample are critical factors in determining these phase transition fields.     

Ultra‐Wide Temperature Stable Dielectrics Based on Bi0.5Na0.5TiO3–NaNbO3 System

The microstructure, phase structure, ferroelectric, and dielectric properties of (1?x)Bi_0.5Na_0.5TiO₃‐xNaNbO₃ [(1?x)BNT‐xNN] ceramics conventionally sintered in the temperature range of 1080°C–1120°C were investigated as a candidate for capacitor dielectrics with wide temperature stability. Perovskite phase with no secondary impurity was observed by XRD measurement. With increasing NN content, (1?x)BNT‐xNN was found to gradually transform from ferroelectric (x = 0–0.05) to relaxor (x = 0.10–0.20) and then to paraelectric state (x = 0.25–0.35) at room temperature, indicated by P–I–E loops analysis, associated with greatly enhanced dielectric temperature stability. For the samples with x = 0.25–0.35, the temperature coefficient of capacitance (TCC) was found <11% in an ultra‐wide temperature range of ?60°C–400°C with moderate dielectric constant and low dielectric loss, promising for temperature stable capacitor applications.     

Investigation of the Structure and Electrical Properties of (KxNa0.96−xLi0.04)(Nb0.96−yTaySb0.04)O3 Piezoelectric Ceramics Modified with Manganese

The effect of high doping levels of manganese (Mn) on the structure and electrical properties of (K_xNa_1?x)NbO₃ (KNN) ceramics containing Li, Ta, and Sb has been investigated. The samples were measured using synchrotron X‐ray diffraction whereas Rietveld refinement with Fullprof was used to determine the structural information as a function of temperature. Temperature‐dependent dielectric measurement was used to compare the phase transition temperatures. The results show that Mn decreases the temperature range of phase coexistence between the orthorhombic and tetragonal phase from ~180°C to ~120°C. The Curie temperature remained unchanged with Mn addition while the dielectric constant and dielectric loss increased with Mn addition. High amounts of Mn led to a reduction in both piezoelectric and ferroelectric properties. The remnant polarization, remnant strain, and piezoelectric coefficient values decreased from 24 μC/cm², 0.000824, 338 ± 37 pm/V to 13 μC/cm², 0,00014 and 208 ± 27 pm/V, respectively for the undoped and 5 mol% Mn‐doped sample.     

Large Strain Response in 0.99(Bi0.5Na0.4K0.1)TiO3–0.01(KxNa1−x)NbO3 Lead‐Free Ceramics Induced by the Change of K/Na Ratio in (KxNa1−x)NbO3

Influence of K/Na ratio in (K_xNa_1?x)NbO₃ on the ferroelectric stability and consequent changes in the electrical properties of 0.99(Bi_0.5Na_0.4K_0.1)TiO₃–0.01(K_xNa_1?x)NbO₃ (BNKT–K_xNN) ceramics were investigated. Results showed that change of K/Na ratio in KNN induces a phase transition from ferroelectric to ergodic relaxor phase with a significant disruption of the long‐range ferroelectric order, and correspondingly adjusts the ferroelectric–relaxor transition point T_F?R to room temperature. Accordingly, giant strain of ~0.46% (corresponding to a large signal d₃₃* of ~575 pm/V) which is comparable to that of Pb‐based antiferroelectrics is obtained at a K/Na ratio of ~1, and the emergence of large strain response induced by the change of K/Na ratio of KNN can be well explained by the correlation between the position of ferroelectric–ergodic relaxor phase boundary in the BNKT–K_xNN system and the tolerance factor t of the end number (K_xNN). In situ high‐energy X‐ray scattering experiments with external field reveals that the large strain response in the studied system is likely related to the electric field‐induced distortion from the pseudocubic structure.