共查询到20条相似文献,搜索用时 156 毫秒
1.
抛光机磨头驱动部件的动态特性分析 总被引:3,自引:1,他引:2
本对抛光机磨头驱动部件的动态特性进行了分析,建立了主轴横向振动的弹性动力学模型,介绍了主要固有频率的计算方法,提出了改善动态特性的措施,对减少主轴振动和避免产生共振有实际意义。 相似文献
2.
使用电磁动态塑化挤出机,对HDPE/CaCO,复合材料的挤出片材做横向和纵向拉伸性能研究。振动力场能够有效地改善HDPE/CaCO,片材的拉伸强度和拉伸断裂伸长率,在本实验范围内,与稳态挤出制品相比,片材的横向和纵向拉伸强度分别提高了16.4%和15.6%,横向和纵向拉伸断裂伸长率分别提高了38.9%和44.0%;振动对材料横向的影响比对纵向更具有规律性。 相似文献
3.
《炭素技术》2016,(5)
铝用炭素材料的弹性模量与其抗热震性有很大的相关性。弹性模量测定分为静态法和动态法,而动态法又有横向振动共振法和纵向振动共振法两种不同的激振方式。从弹性模量的类别来说,静态法和纵向振动共振法都属于长度方向上的应力应变关系,也称之为杨氏模量,而横向振动共振法本质上是切变模量。铝用炭素材料因骨料颗粒较大,不能普遍适合采用横向振动共振法测定弹性模量,而静态法和纵向振动共振法能够很好地测定铝用炭素材料弹性模量。由于铝用炭素材料弹性形变阶段的非线性,采用静态法测定的结果明显要比纵向振动共振法小。鉴于铝用炭素材料在铝电解过程中处于受迫振动状态,采用纵向振动共振法测定弹性模量能够更加真实地反映铝电解生产的实际情况。 相似文献
4.
5.
振动力场对m-PE-LLD薄膜拉伸强度的影响 总被引:1,自引:0,他引:1
使用电磁动态吹膜机组加工m-PE-LLD薄膜,将振动力场引入到塑化挤出的全过程,考察了振动力场对m-PE-LLD薄膜拉伸强度的影响。研究发现,振动力场的加入使m-PE-LLD吹塑薄膜的横向强度增大、纵向强度减小,纵、横向拉伸强度趋于均匀。振动力场对PE-LD和PE-HD的拉伸强度的影响具有相似的规律,初步的分析机理认为:振动力场引入后,聚合物熔体同时受到轴向和周向的作用力,分子链会沿两个作用力的方向进行排列,形成网格化排列的结构,从而使薄膜纵、横向强度趋于均一。 相似文献
6.
7.
为了减少风机自身振动对混凝土基础和周边设备的影响,将风机底座与混凝土基础固定方式由地脚螺栓固定改造为使用ZD型阻尼弹簧减振器直接放置在混凝土基础上,改造后风机横向和纵向振动明显降低,混凝土基础振动明显减小,取得了很好的减振和隔振效果. 相似文献
8.
9.
介绍氯气压缩机主轴成分;分析主轴发生裂纹的原因是:淬火前组织中存在缺陷,导致纵向裂纹;提出改进措施:锻件在进行调质处理前再进行一次正火处理。 相似文献
10.
选取某款弱化沟槽呈“H”形的聚碳酸酯/丙烯腈?丁二烯?苯乙烯共聚物(PC/ABS)合金材质安全气囊盖板为研究对象,并构建了其有限元仿真模型,对比有限元力学仿真分析结果与理论计算值验证了该有限元仿真模型的可靠性;通过ISIGHT软件集成Catia和ANSYS,选取安全气囊盖板弱化沟槽的横向长度、深度,纵向长度、深度4个参数作为设计变量,选取弱化沟槽横向最大应力与纵向最大应力作为响应变量,分析了设计变量对响应变量的贡献度分布特征并采用NSGA遗传算法对响应变量多目标优化。结果表明,横向长度、纵向深度对横向最大应力为负贡献度,横向深度、纵向长度为正贡献度;横向深度、纵向长度对纵向最大应力为负贡献度,横向长度、纵向深度为正贡献度;在合理范围内,4个参数值的优化设计,实现了横向最大应力提高和纵向最大应力降低的多目标优化,有效减少了安全气囊盖板爆破时产生的碎屑量,提升了产品的安全性能。 相似文献
11.
12.
聚酯饮料瓶结晶与取向研究 总被引:1,自引:0,他引:1
应用广角 X射线衍射及密度法研究了聚酯饮料瓶结晶与取向及其原料和半成品的结构。结果表明 ,聚酯饮料瓶坯已有晶核生成 ,在聚酯瓶成型过程中 ,由于纵向拉伸与横向吹胀阶段拉伸张力的各向异性 ,聚酯产生了方向不同的结晶与取向作用 ,导致 PET瓶料的结晶与取向的差异。广角 X射线衍射法可以测定聚酯饮料瓶结晶与取向结构 ,可为固相缩聚 PET的聚合及吹瓶工艺提供参考。 相似文献
13.
14.
对1107JC泵轴断裂原因进行了分析,结果表明,大尺寸的非金属夹杂和背帽外缘的点焊是引起泵轴过早断裂的主要原因。在分析的基础上提出了预防断裂的措施。 相似文献
15.
16.
A shaft kiln is considered to be a promising pyrolysis device for the efficient decomposition of municipal wastes. In this device, the temperature distributions of the gas and solid phases can be separately controlled, thereby leading to considerably different profiles for both the phases. The temperature controllability in a shaft kiln helps us to obtain a suitable profile of the gas-phase temperature for the decomposition of tar that evolves from the solid phase. By leveraging this advantage of the shaft kiln, we performed further pyrolysis and steam reforming of the volatiles formed from the pyrolysis of biomass and several polymers using a two-stage reactor that was maintained at different temperatures. The amount of tar decreased with an increase in the temperature in the upper reactor in the absence of a catalyst. By using the experimental results, we developed a lumped kinetic model for secondary gas-phase reactions and performed a kinetic analysis of the reactions that proceeded in the upper reactor. It is confirmed that the simulation model is successful in reproducing the product distribution of the gas-phase reactions of volatiles from biomass and polymers. 相似文献
17.
通过改造,可从加工UDY原丝变为加工POY原丝.扩大了适用范围和使用价值。分析了未改造前出现的问题,并介绍了罗拉辊联轴器改造方案、工艺过程以及改造后的使用效果. 相似文献
18.
19.
In this paper,we consider the process development and scaling up of trickle-bed reactor for 1,4-butynediolsynthesis.Three laboratory chemical reactors have been used,i.e.,a batchwise stirred kettle for the de--termination of intrinsic kinetics,a continuous rotating basket reactor for macrokinetics of large catalystpellets,and an external recycle differential trickle-bed reactor for bed-kinetics under liquid flow rates of in-dustrial equipment.The kinetic data obatined from above three reactors can be correlated in power form rate equations,and the results not only present definite proof of the relationships between contacting effectiveness factorsand liquid flow rates developed by Satterfield,but also verify the influences of liquid flow rates under higherand lower temperatures.The external contacting effectiveness factors in trickle-bed reactor we determined can be used to correctthe macrokinetic models of catalyst pellets determined from rotating basket,and the corrected kinetic modelscan be checked by an adiabatic pilot equipment with rather successful results. 相似文献
20.