Photocatalytic properties of SrTiO3 nanoparticles prepared by a polyacrylamide gel route

A polyacrylamide gel method has been used to prepare SrTiO₃ nanoparticles. It is found that the choice of chelating agent has a great influence on the SrTiO₃ synthesis. The use of citric acid as the chelating agent leads to the synthesis of pure SrTiO₃ at a calcination temperature of 550 °C. By using the chelating agent acetic acid, however, a much higher calcination temperature at 800 °C is required to produce a single sample. The citric acid- and acetic acid-resulted samples exhibit both sphere- particle morphology, and have an average particle size of ~ 55 nm and ~ 100 nm, respectively. The photocatalytic properties of the as-prepared SrTiO₃ nanoparticles have been investigated by the degradation of Congo Red, RhB, MO, and MB under ultraviolet irradiation. The citric acid-resulted sample is found to exhibit a photocatalytic activity higher than the acetic acid-resulted sample, expectedly due to its relatively smaller particle size. In addition, different degradation efficiencies are found between the dyes, and the highest degradation efficiency is observed for Congo Red.     

Influence of processing method on the properties of hydroxyapatite nanoparticles in the presence of different citrate ion concentrations

The objective of this study was to investigate the effect of processing methods on the formation of ultra fine hydroxyapatite (HAp) nanoparticles in the presence of citrate ions and analyze their various physical properties. The addition of the citrate ions was found to reduce the size and prevent the agglomeration of HAp particles dramatically in the high gravity (HG) method compared to precipitation method. In precipitation method, the particle size reduced from 300 ± 70 nm to 90 ± 20 nm with the addition of citrate ions. In high gravity method, the particle size decreased more significantly from 80 ± 10 nm to 13 ± 5 nm with the addition of citrate ions. Furthermore, more uniform size distribution of nanoparticles was achieved in high gravity method. X-ray diffraction of nanoparticles prepared in both method exhibited slight shift of peaks to the higher angle with the addition of citric acid, indicating the incorporation of carbonate (CO₃) content in the HAp nanoparticles irrespective of the particle size. The mechanical properties of HWMPE matrix composite reinforced with nanoparticles was examined and this nanocomposite with nanoparticles prepared in high gravity method with the addition of citrate ions showed increased mechanical strength due to the considerable reduction in the particle size and higher uniformity of the particles. In vitro cellular analyses of the nanoparticle prepared in high gravity with the addition of citrate ions also displayed the most pronounced spreading of cell growth.     

Fabrication and photocatalytic activity of YMn2O5 nanoparticles

In this work, a polyacrylamide gel route is introduced to synthesize YMn₂O₅ nanoparticles. It is demonstrated that high-quality YMn₂O₅ nanoparticles with a uniform size and spherical shape can be prepared using different chelating agents. However, the average particle size of the products is found to have a dependence on the choice of the chelating agent. The sample prepared using citric acid as the chelating agent has an average particle size of ~ 45 nm, while the sample prepared by using the chelating agent EDTA has a particle size centered around 70 nm. The optical energy bandgap of the citric acid- and EDTA-resulted samples is obtained, from optical absorption measurements, to be 1.21 and 1.17 eV, respectively. The photocatalytic experiments reveal that the as-prepared YMn₂O₅ nanoparticles exhibit an interesting photocatalytic activity for oxidative decomposition of methyl red under ultraviolet and visible-light irradiation.     

Characterization of silica-coated Ag nanoparticles synthesized using a water-soluble nanoparticle micelle

This article describes the synthesis of silica-coated Ag nanoparticles using a water-soluble nanoparticle micelle under basic conditions. Monodispersed Ag nanoparticles with a mean particle size of 7 nm were synthesized using AgNO₃ in the presence of ascorbic acid as a reducing agent. The Ag nanoparticles were easily re-dispersed into an aqueous solution by surface adsorption of surfactant molecules, indicating formation of water-soluble nanoparticle micelles. Silica-coated Ag nanoparticles ranging in size from 50 to 100 nm were obtained by controlling the surfactant, Ag nanoparticle and tetraethylortho silicate (TEOS) concentrations. Adsorbed surfactant monolayers on Ag nanoparticles were used as a template for the silica shell because of the hydrophobicity of TEOS. In all cases, the size of the resulting particles increased linearly as these concentrations increased. Based on transmission electron microscopy, all the Ag nanoparticles were completely covered with a silica shell. In most samples, however, Ag nanoparticle size increased from 7 to 50 nm due to evaporation of hexane by heating. Although mean particle size of silica-coated Ag nanoparticles was drastically altered, characteristic absorption peaks were observed at approximately 410 nm.     

络合剂和交联剂对凝胶法制备TbMnO3纳米颗粒的影响

采用改进的聚丙烯酰胺凝胶法制备了TbMnO3纳米颗粒．以Tb和Mn的无机盐水溶液为原料,通过加入丙烯酰胺使溶液成胶,在溶液成胶过程中,丙烯酰胺聚合形成高分子网络骨架,为粒子提供生长的空间．利用热重（TG）分析、差示扫描量热（DSC）分析、傅里叶变换红外光谱仪（FTIR）及X射线衍射（XRD）等多种手段研究了干凝胶的热分解及TbMnO,的形成．实验表明,分别以柠檬酸和EDTA作为络合剂,在800℃煅烧温度下均可制备出高纯TbMnO3纳米颗粒,但产物的颗粒尺寸和形貌与络合剂的选取有关．扫描电子显微镜（SEM）观察显示,以柠檬酸为络合刺制得的样品,颗粒形貌规整,呈球形,颗粒尺寸分布较窄,平均粒径约为67nm;以EDTA为络合剂制得的样品,颗粒形态主要以长球形和近球形为主,兼有少量的杆状,平均颗粒尺寸约为115nm．此外,实验还发现,在前驱体溶液中加入适量的双丙烯酰胺,可以使产物颗粒的尺寸适度减小,形貌变得更为规整．磁滞回线测量结果表明,TbMnO3纳米颗粒在室温下表现为顺磁性．     

Synthesis of spherical NiO nanoparticles through a novel biosurfactant mediated emulsion technique

Spherical nickel oxide nanoparticles were synthesized by microemulsion technique using rhamnolipids as the surfactant along with n-heptane and water. Nickel hydroxide (Ni(OH)₂) particles were first formed which were then calcined to obtain nickel oxide (NiO) particles. Scanning Electron Microscopy (SEM) studies revealed that the synthesized nickel hydroxide particles were spherical in shape with stacked lamellar sheets. Nickel hydroxide was converted to nickel oxide by calcinations at 600 °C for 3 h and was confirmed by X-ray Diffraction (XRD) analysis. Transmission Electron Microscopy (TEM) showed that the nickel oxide particles were crystalline and of uniform size. The effect of pH on particle size was investigated and it was found that the particle size decreased from 86 ± 8 nm at pH 11.6 to 47 ± 5 nm at pH 12.5. A novel method using rhamnolipid biosurfactant for microemulsion synthesis has been demonstrated which offers an eco-friendly alternative to conventional microemulsion technique based on organic surfactants.     

Synthesis of cobalt boride nanoparticles using RF thermal plasma

Nanosize cobalt boride particles were synthesized from the vapor phase using a 30 kW–4 MHz radio frequency (RF) thermal plasma. Cobalt and boron powder mixtures used as precursors in different composition and feed rate were evaporated immediately in the high temperature plasma and cobalt boride nanoparticles were produced through the quenching process. The X-ray diffractometry (XRD) patterns of cobalt boride nanoparticles prepared from the feed powder ratio of 1:2 and 1:3 for Co:B showed peaks that are associated with the Co₂B and CoB crystal phases of cobalt boride. The XRD analysis revealed that increasing the powder feed rate results in a higher mass fraction and a larger crystalline diameter of cobalt boride nanoparticles. The images obtained by field emission scanning electron microscopy (FE-SEM) revealed that cobalt boride nanoparticles have a spherical morphology. The crystallite size of the particles estimated with XRD was found to be 18–22 nm.     

Sintering behavior of spherical aggregated nanoparticles prepared by spraying colloidal precursor in a heated flow

The sintering behavior of spherical aggregated nanoparticles prepared by spraying colloidal precursor into a heated flow was investigated both experimentally and theoretically. Spherical micrometer-sized particles consisting of compactly aggregated nanoparticles were formed, due to solvent evaporation and the drying process of the colloidal precursor. The degree of sintering of aggregated nanoparticles depended on the furnace temperature profile, residence time and primary particle size of the aggregated nanoparticles. Spherical monodispersed colloidal silica, in sizes ranging from 22 to 100 nm was selected as the primary particles. The sintering rate increased with temperature and residence time, and decreased with increasing primary particle size. The aggregated nanoparticles sintered completely, resulting in particles with smooth surfaces that were synthesized at 1400 °C, residence time 31.7 s that was obtained by using a carrier gas flow rate of 1.5 L/min and 0.1 M colloidal silica nanoparticles 100 nm in size. An appropriate model of sintering in the system was proposed to explain the shrinkage and the neck growth of the aggregated nanoparticles. The sintering analysis suggested that solid-state volume diffusion suitably described the sintering mechanism of spherical aggregated silica nanoparticles in a heated flow.     

Experimental measurements of gold nanoparticle nucleation and growth by citrate reduction of HAuCl4

Gold particle nucleation and growth were analyzed systematically by UV–vis, ELS and TEM measurements. The gold seed particles ranging from 14.3 nm to 20.3 nm were prepared with monodisperse size distribution by citrate reduction reaction of various initial HAuCl₄ concentrations. Gold nanoparticles of different sizes were made by the seed-mediated growth process. In the first stage of seed-mediated growth, most of gold precursors were used for the growth of seed particles, but, further supply of gold precursors promotes the nucleation of small particles and decreases the average particle diameters while the polydispersity of particles increases. This research can be used as basic data to prepare gold nanoparticles with specific properties for different applications.     

Template-free hydrothermal derived cobalt oxide nanopowders: Synthesis,characterization, and removal of organic dyes

Pure spinel cobalt oxide nanoparticles were prepared through hydrothermal approach using different counter ions. First, the pure and uniform cobalt carbonate (with particle size of 21.8–29.8 nm) were prepared in high yield (94%) in an autoclave in absence unfriendly organic surfactants or solvents by adjusting different experimental parameters such as: pH, reaction time, temperature, counter ions, and (Co²⁺:CO₃^2?) molar ratios. Thence, the spinel Co₃O₄ (with mean particle size of 30.5–47.35 nm) was produced by thermal decomposition of cobalt carbonate in air at 500 °C for 3 h. The products were characterized by powder X-ray diffraction (XRD), Fourier transform infrared (FTIR), transmission electron microscope (TEM), scanning electron microscope (SEM), and thermal analysis (TA). Also, the optical characteristics of the as-prepared Co₃O₄ nanoparticles revealed the presence of two band gaps (1.45–1.47, and 1.83–1.93 eV). Additionally, adsorption of methylene blue dye on Co₃O₄ nanoparticles was investigated and the uptake% was found to be >99% in 24 h.     

Synthesis of nanocrystalline GaN from Ga2O3 nanoparticles derived from salt-assisted spray pyrolysis

Gallium nitride (GaN) nanoparticles were successfully produced from nano-sized gallium oxide (Ga₂O₃) particles under a flow of ammonia gas. The gallium oxide nanoparticles were prepared by salt-assisted spray pyrolysis (SASP). Highly crystalline Ga₂O₃ nanoparticles with an average diameter of approximately 10 nm were obtained at various temperatures when a flux salt (LiCl, 5 mol/l) was added to the precursor solution. The effects of the crystallinity of the Ga₂O₃ particles and nitridation time on transformation to GaN were characterized using X-ray diffraction and scanning/transmission electron microscopy. Highly crystalline GaN nanoparticles with a mean size of 23.4 nm and a geometric standard deviation of 1.68 nm were obtained when Ga₂O₃ nanoparticles with relatively low crystallinity were used as the starting material. The resulting GaN nanoparticles showed a photoluminescence peak at 364 nm under UV excitation at 254 nm.     

The novel,one step and facile synthesis of ZnO nanoparticles using heteropolyoxometalates and their photoluminescence behavior

A novel and facile wet chemical method is presented to synthesize zinc oxide nanoparticles (NPs) under ambient atmosphere and temperature. Keggin type heteropolyoxometalate (H₃[PW₁₂O₄₀]) was used as stabilizer and the effect of stirring time and amount of H₃[PW₁₂O₄₀] (HPW) were studied. XRD and TEM techniques were applied for the morphological and structural characterizations of NPs. Size of nanoparticles were determined using TEM, Scherrer’s formula as well as effective mass approximation. The results of these three methods are in good agreements and revealed single hexagonal zincite type crystalline with average particle size in the range of 3–15 nm. Photoluminescence behavior of the prepared sample shows a strong orange to red emission centred at about 620–635 nm, a green emission at around 550 nm and broad UV emission at around 400 nm.     

Optical investigations on indium oxide nano-particles prepared through precipitation method

Visible light emitting indium oxide nanoparticles were synthesized by precipitation method. Sodium hydroxide dissolved in ethanol was used as a precipitating agent to obtain indium hydroxide precipitates. Precipitates, thus formed were calcined at 600 °C for 1 h to obtain indium oxide nanoparticles. The structure of the particles as determined from the X-Ray diffraction pattern was found to be body centered cubic. The phase transformation of the prepared nanoparticles was analyzed using thermogravimetry. Surface morphology of the prepared nanoparticles was analyzed using high resolution-scanning electron microscopy and transmission electron microscopy. The results of the analysis show cube-like aggregates of size around 50 nm. It was found that the nanoparticles have a strong emission at 427 nm and a weak emission at 530 nm. These emissions were due to the presence of singly ionized oxygen vacancies and the nature of the defect was confirmed through Electron paramagnetic resonance analysis.     

Effect of different solvents in the synthesis of LaCoO3 nanopowders prepared by the co-precipitation method

This paper describes the obtention of LaCoO₃ nanopowders by the co-precipitate method with ammonium hydroxide from solvent such as water, ethyl alcohol and ethylene glycol. The crystalline structure and average particle size are dependent of type-solvent. The XRD patterns indicated that the LaCoO₃ nanopowders prepared with water and ethyl alcohol exhibit a pure perovskite-type LaCoO₃ in the rhombohedra structure. The average diameter of the particles prepared with ethyl alcohol and water are 27 ± 4.49 nm and 64.4 ± 12.92 nm respectively. High resolution transmission electron microcopy revealed an oriented attachment mechanism for the growth of aggregated LaCoO₃ nanocrystals. Room temperature magnetization results of the heat treated LaCoO₃ nanopowders exhibited a paramagnetic behavior. The average particle size and formation temperature of LaCoO₃ obtained in this study is comparatively lower than those reported in the literature.     

Physical and electrochemical study of cobalt oxide nano- and microparticles

Cobalt oxide nanocrystals of size 17–21 nm were synthesized by a simple reaction between cobalt acetate (II) and dodecylamine. On the other hand, micrometric Co₃O₄ was prepared using the ceramic method. The structural examination of these materials was performed using powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and transmission electron microscopy (TEM and HRTEM). XRD studies showed that the oxides were pure, well-crystallized, spinel cubic phases with a-cell parameter of 0.8049 nm and 0.8069 nm for the nano and micro-oxide, respectively. The average particle size was 19 nm (nano-oxide) and 1250 μm (micro-oxide). Morphological studies carried out by SEM and TEM analyses have shown the presence of octahedral particles in both cases. Bulk and surface properties investigated by X-ray photoelectron spectroscopy (XPS), point zero charge (pzc), FTIR and cyclic voltammetry indicated that there were no significant differences in the composition on both materials. The magnetic behavior of the samples was determined using a vibrating sample magnetometer. The compounds showed paramagnetic character and no coercivity and remanence in all cases. Galvanostatic measurements of electrodes formed with nanocrystals showed better performance than those built with micrometric particles.     

Microwave-assisted synthesis of BaWO4 nanoparticles and its photoluminescence properties

Single-crystal BaWO₄ nanoparticles have been successfully synthesized under microwave irradiation. The results show that nearly monodisperse BaWO₄ nanoparticles have been successfully prepared without using surfactants. The products were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and photoluminescence (PL). The XRD results indicated that the BaWO₄ nanoparticles obtained had a tetragonal unit cell (a = 0.5612, c = 1.2706 nm). The TEM images show that the as-prepared BaWO₄ have good narrow particle-sized distributions containing a number of nanoparticles with uniform sizes. The products show a strong photoluminescence peak at 432–436 nm with the excitation at 365 nm.     

Synthesis and characterization of magnetite nanoparticles via the chemical co-precipitation method

Magnetite nanoparticles were synthesized via the chemical co-precipitation method using ammonium hydroxide as the precipitating agent. The size of the magnetite nanoparticles was carefully controlled by varying the reaction temperature and through the surface modification. Herein, the hexanoic acid and oleic acid were introduced as the coating agents during the initial crystallization phase of the magnetite. Their structure and morphology were characterized by the Fourier transform infrared spectroscopy (FTIR), the X-ray diffraction (XRD) and the field-emission scanning electron microscopy (FE-SEM). Moreover, the electrical and magnetic properties were studied by using a conductivity meter and a vibrating sample magnetometer (VSM), respectively. Both of the bare magnetite and the coated magnetite were of the cubic spinel structure and the spherical-shaped morphology. The reaction temperature and the surface modification critically affected the particle size, the electrical conductivity, and the magnetic properties of these particles. The particle size of the magnetite was increased through the surface modification and reaction temperature. In this study, the particle size of the magnetite nanoparticles was successfully controlled to be in the range of 10–40 nm, suitable for various biomedical applications. The electrical conductivity of the smallest particle size was 1.3 × 10^?3 S/cm, within the semi-conductive materials range, which was higher than that of the largest particle by about 5 times. All of the magnetite nanoparticles showed the superparamagnetic behavior with high saturation magnetization. Furthermore, the highest magnetization was 58.72 emu/g obtained from the hexanoic acid coated magnetite nanoparticles.     

Mixture of fuels approach for the solution combustion synthesis of LaAlO3 nanopowders

A modified solution combustion approach was used in the preparation of nanosize LaAlO₃ (～23.6 nm) using mixture of citric acid and oxalic acid as fuels with corresponding metal nitrates. The synthesized and calcined powders were characterized by Fourier transform infra red spectrometry (FTIR), Differential thermal analysis-Thermogravimetry analysis (DTA–TGA), X-ray diffractometry (XRD) and Transmission electron microscopy (TEM). The FTIR spectra show the lower frequency bands at 656 and 442 cm^?1corresponds to metal–oxygen bonds (possible La–O and Al–O stretching frequencies) vibrations for the perovskite structure compound. DTA confirms the formation temperature of LaAlO₃ varies between 830–835 °C. XRD results show that mixture of fuels ratio is influential on the crystallite size of the resultant powders. The average particle size of LaAlO₃-1 as determined from TEM was about 41 nm, whereas for LaAlO₃-2 and LaAlO₃-3 samples, particles are seriously aggregated.     

Structural and magnetic properties of pristine and Fe-doped NiO nanoparticles synthesized by the co-precipitation method

Ni_1?xFe_xO (x = 0 and 0.03) nanoparticles are synthesized by a chemical route. XRD and TEM measurements confirm phase purity and crystallinity of the nanoparticles. Fe substitution in NiO reduces considerably the average particle size of the nanoparticles. The pristine NiO sample with size 14 nm and Fe-substituted sample having size 7 nm show room temperature ferromagnetism. The pristine NiO having 31 nm size and Fe-substituted sample with size 25 nm are found to be antiferromagnetic. The M–H and M–T behavior of the pristine and Fe-doped samples are explained with a core–shell model with an antiferromagnetic core and a ferromagnetic shell. The disordered spins at the shell give rise to a spin-glass like frozen state below 10 K. The obtained room temperature ferromagnetism in the pristine and Fe-doped NiO has been attributed to particle size effect.     

Synthesis of MSnO3 (M = Ba,Sr) nanoparticles by reverse micelle method and particle size distribution analysis by whole powder pattern modeling

Light-to-electricity conversion efficiency in dye-sensitized solar cells critically depends not only on the dye molecule, semiconducting material and redox shuttle selection but also on the particle size and particle size distribution of the semiconducting photoanode. In this study, nanocrystalline BaSnO₃ and SrSnO₃ particles have been synthesized using the microemulsion method. Particle size distribution was studied by whole powder pattern modeling which confirmed narrow particle size distribution with an average size of 18.4 ± 8.3 nm for SrSnO₃ and 15.8 ± 4.2 nm for BaSnO₃. These values are in close agreement with results of transmission electron microscopy. The prepared materials have optimal microstructure for successive investigation in dye-sensitized solar cells.