Investigation of non-aqueous electrodeposited CdS/Cd1−xZnxTe heterojunction solar cells

Polycrystalline Cd_1−xZn_xTe solar cells with efficiency of 8.3% were grown by cathodic electrodeposition on glass/ITO/CdS substrates using non-aqueous ethylene glycol bath. The deposit is characterised versus the process conditions by XRD and found to possess a preferred (1 1 1) orientation on Sb doping in the electroplating bath. The surface morphology of the deposit is studied using atomic force microscope. The average RMS roughness for the ternary film was higher than that for the binary CdTe. Optical properties of the films were carried out to study the band gap and calculation of molar concentration ‘x’. The effects of Sb doping in CdS/Cd_1−xZn_xTe heterojunctions have been studied. The short circuit current density (c) was found to improve and series resistance (R_s) reduced drastically upon Sb doping. This improvement in J_sc is attributed to an increase in quantum efficiency. The evaluation of solar cell parameters was also carried out using the current–voltage characteristics in dark and illumination. The best results were obtained when 2×10⁻³ M ZnCl₂ along with antimony were present in the deposition bath. Under AM 1.5 conditions the open circuit voltage, short circuit current density, and fill factor of our best cell were V_oc=600 mV, J_sc=26.66 mA/cm², FF=0.42 and efficiency, η=8.3%. The carrier concentration and built-in potential of Cd_1−xZn_xTe calculated from Mott–Schottky plot was 2.72×10¹⁷ cm⁻³ and 1.02 eV.     

Influence of aminothiazole additives in I/I3 redox electrolyte solution on Ru(II)-dye-sensitized nanocrystalline TiO2 solar cell performance

The influence of aminothiazole additives in acetonitrile solution of an I⁻/I₃⁻ redox electrolyte on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′- bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) (N719) dye-sensitized TiO₂ solar cell was studied. The current–voltage characteristics were investigated under AM 1.5 (100 mW/cm²) for nine different aminothiazole compounds. The aminothiazole additives tested had varying influences on the solar cell performance. Most of the additives enhanced the open-circuit photovoltage (V_oc), but reduced the short circuit photocurrent density (J_sc) of the solar cell. Both the physical and chemical properties of the aminothiazoles were computationally calculated in order to determine the reasons that the additive influenced solar cell performance. The larger the calculated partial charge of the nitrogen atom in the thiazole, the higher the V_oc value. The V_oc value increased as the dipole moment of aminothiazoles in acetonitrile increased. Moreover, the V_oc of the solar cell also increased as the size of the aminothiazole molecules decreased. These results suggest that the electron donicity of the aminothiazole additives influenced the interaction with the TiO₂ photoelectrode, which altered the dye-sensitized solar cell performance.     

InA1As/InGaAs low-band-gap cell on InP for high efficiency multi-structure solar cell system

InA1As/InGaAs solar cells on InP for a low-band-gap cell have been fabricated. From theoretical simulation it is expected that the optimized InA1As/InGaAs cell should have photovoltaic characteristics values of J_sc = 21.2 mA cm⁻², V_oc = 0.345 V, FF = 0.745 and ν = 4.02% at one sun AM0 without an AR-coating. The best performance achieved by experiment was J_sc = 22.0 mA cm⁻², V_oc = 0.320 V, FF = 0.695, ν = 3.61% without an AR-coating. The uniformity of the characteristics was much improved utilizing the InGaAs cap layer for a low contact resistivity.     

Influence of alkylaminopyridine additives in electrolytes on dye-sensitized solar cell performance

The influence of alkylaminopyridine additives on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell with an I⁻/I₃⁻ redox electrolyte in acetonitrile was studied. The current–voltage characteristics were measured for more than 20 different alkylaminopyridines under AM 1.5 (100 mW/cm²). The alkylaminopyridine additives tested had varying effects on the performance of the cell. All the additives decreased the short circuit photocurrent density (J_sc), but increased the open-circuit photovoltage (V_oc) of the solar cell. Molecular orbital calculations imply that the dipole moment of the alkylaminopyridine molecules influences the J_sc of the cell and that the size, solvent accessible surface area, and ionization energy all affect the V_oc of the cell. The highest V_oc of 0.88 V was observed in an electrolyte containing 4-pyrrolidinopyridine, which is comparable to the maximum V_oc of 0.9 V for a cell consisting of TiO₂ electrode and I⁻/I₃⁻ redox system.     

Highly efficient photon-to-electron conversion with mercurochrome-sensitized nanoporous oxide semiconductor solar cells

Dye-sensitized solar cells based on nanoporous oxide semiconductor thin films such as TiO₂, Nb₂O₅, ZnO, SnO₂, and In₂O₃ with mercurochrome as the sensitizer were investigated. Photovoltaic performance of the solar cell depended remarkably on the semiconductor materials. Mercurochrome can convert visible light in the range of 400–600 nm to electrons. A high incident photon-to-current efficiency (IPCE), 69%, was obtained at 510 nm for a mercurochrome-sensitized ZnO solar cell with an I⁻/I₃⁻ redox electrolyte. The solar energy conversion efficiency under AM1.5 (99 mW cm⁻²) reached 2.5% with a short-circuit photocurrent density (J_sc) of 7.44 mA cm⁻², a open-circuit photovoltage (V_oc) of 0.52 V, and a fill factor (ff) of 0.64. The J_sc for the cell increased with increasing thickness of semiconductor thin films due to increasing amount of dye, while the V_oc decreased due to increasing of loss of injected electrons due to recombination and the rate constant for reverse reaction. Dependence of photovoltaic performance of mercurochrome-sensitized solar cells on semiconductor particles, light intensity, and irradiation time were also investigated. High performance of mercurochrome-sensitized ZnO solar cells indicate that the combination of dye and semiconductor is very important for highly efficient dye-sensitized solar cells and mercurochrome is one of the best sensitizers for nanoporous ZnO photoelectrode. In addition, a possibility of organic dye-sensitized oxide semiconductor solar cells has been proposed as well as one using metal complexes.     

Influence of electrolytes on the photovoltaic performance of organic dye-sensitized nanocrystalline TiO2 solar cells

We have studied the influence of electrolytes on the photovoltaic performance of mercurochrome-sensitized nanocrystalline TiO₂ solar cells using LiI, LiBr, and tetraalkylammonium iodides as the electrolyte. Short-circuit photocurrent density (J_sc) and open-circuit photovoltage (V_oc) depended strongly on the electrolyte. J_sc of 3.42 mA cm⁻² and V_oc of 0.52 V were obtained for the LiI electrolyte and J_sc of 2.10 mA cm⁻² and V_oc of 0.86 V were obtained for the Pr₄NI electrolyte. This difference in photovoltaic performance was due to the change in the conduction band level of the TiO₂ electrode. Large V_oc of 0.99 V was obtained for the LiBr electrolyte due to the large energy gap between the conduction band level of TiO₂ and the Br/Br₂ redox potential. Solar cell performance also depended strongly on organic solvent, suggesting that the physical properties of solvents such as Li ion conductivity and donor number affect photovoltaic performance.     

Properties of CuIn1−xGaxSe2

Polycrystalline bulk samples of CuIn_1−xGa_xSe₂ weregrown with nominal x = 0.15, 0.25 and 0.5. Mobility, conductivity and band gap were measured at room and low temperatures. Mobilities for x = 0.21 were several hundred cm² V⁻¹s⁻¹ at room temperature and for x = 0.15 were 10³ cm² V⁻¹ s⁻¹, all n type. The band gaps were estimated from the spectra of photoelectrochemical cells at room temperature (with 8.5 K photoluminescence estimates shown in brackets), as 1.10 eV (1.14) for x = 0.21, and 1.07 eV (1.093) for x = 0.15. Crystal mechanical properties as regards cracks were not as good as for CuInSe₂, using similar growth techniques.     

Boron-doped diamond-like amorphous carbon as photovoltaic films in solar cell

In this paper, the photovoltaic feature of metal-boron carbide-silicon (MCS) solar cell was reported. The boron-doped diamond-like carbon thin film on n-silicon substrate has been prepared using arc-discharge plasma chemical vapor deposition (PCVD) technique. The conductivity and the resistivity of the film were measured by Bio-Rad Hall5500PC system to be p-type semiconductor and 3–12 Ω cm/□, respectively. The boron content in the films was about 0.8–1.2%, obtained from Auger electron spectroscopy (AES), and some microcrystalline diamond grains (0.5–1.0 μm) embedded in the mainly amorphous network were revealed through scanning electron microscope (SEM) and Raman spectrum. The performance of Au/C(B)/n-Si heterojunction solar cells has been given under dark I–V rectifying curve and I–V working curve (with 100 mW cm⁻² illumination). A measurement of open-circuit voltage V_oc=580 mV and short-circuit current density J_sc=32.5 mA cm⁻² was obtained. Accordingly, the energy conversion efficiency of the device was tentatively determined to be about 7.9% in AM 1.5, 100 mW/cm² illuminated.     

Influence of pyrazole derivatives in I/I3 redox electrolyte solution on Ru(II)-dye-sensitized TiO2 solar cell performance

The influence of pyrazole additives in an I⁻/I₃⁻ redox electrolyte solution on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) (N719) dye-sensitized TiO₂ solar cell was studied. The current–voltage characteristics of the cell were measured using 18 different pyrazole derivatives. All of the pyrazole additives enhanced the open-circuit photovoltage (V_oc) and the solar energy conversion efficiency (η), but reduced the short-circuit photocurrent density (J_sc). Most of the pyrazoles improved fill factor (ff). The physical and chemical properties of the pyrazoles were computationally calculated in order to elucidate the reasons for the additive effects on cell performance. The greater the partial charge of the nitrogen atom at position 2 in the pyrazole group, the larger the V_oc, but the smaller the J_sc values. As the dipole moment of the pyrazole derivatives increased, the V_oc value increased, but the J_sc value decreased. The V_oc of the cell also increased as the ionization energy of the pyrazoles decreased. These results suggest that the electron donicity of the pyrazole additives affected the interaction with the nanocrystalline TiO₂ photoelectrode, the I⁻/I₃⁻ electrolyte, and the acetonitrile solvent, which changed the Ru(II)-dye-sensitized solar cell performance.     

Blue sensitizers for solar cells: Natural dyes from Calafate and Jaboticaba

Blue-violet anthocyanins from Jaboticaba (Myrtus cauliflora Mart) and Calafate (Berberies buxifolia Lam) were employed as TiO₂ dye-sensitizers. Solar cells sensitized by Jaboticaba extracts achieved up to J_sc=9.0 mA cm⁻², V_oc=0.59 V, P_max=1.9 mW cm⁻² and ff=0.54, while for Calafate sensitized cells the values determined were up to J_sc=6.2 mA cm⁻², V_oc=0.47 V, P_max=1.1 mW cm⁻² and ff=0.36. Other natural dyes were evaluated without significant photocurrent, demonstrating that only selected extracts are capable of converting sunlight in electricity. The results obtained with extracts of Jaboticaba and Calafate show a successful conversion of visible light into electricity by using natural dyes as wide band-gap semiconductor sensitizers in dye-sensitized solar cells. It also represents an environmentally friendly alternative for dye-sensitized solar cells with low cost production and an excellent system for educational purposes.     

New trends to grow the n-CdZn (S1−xSex)2/p-CuIn(S1−xSex)2 heterojunction thin films for solar cell applications

The n-CdZn(S_1−xSe_x) and p-CuIn(S_1−xSe_x)₂ thin films have been grown by the solution growth technique (SGT) on glass substrates. Also the heterojunction (p–n) based on n-CdZn (S_1−xSe_x)₂ and p-CuIn (S_1−xSe_x)₂ thin films fabricated by same technique. The n-CdZn(S_1−xSe_x)₂ thin film has been used as a window material which reduced the lattice mismatch problem at the junction with CuIn (S_1−xSe_x)₂ thin film as an absorber layer for stable solar cell preparation. Elemental analysis of the n-CdZn (S_1−xSe_x)₂ and p-CuIn(S_1−xSe_x)₂ thin films was confirmed by energy-dispersive analysis of X-ray (EDAX). The structural and optical properties were changed with respect to composition ‘x’ values. The best results of these parameters were obtained at x=0.5 composition. The uniform morphology of each film as well as the continuous smooth thickness deposition onto the glass substrates was confirmed by SEM study. The optical band gaps were determined from transmittance spectra in the range of 350–1000 nm. These values are 1.22 and 2.39 eV for CuIn(S_0.5Se_0.5)₂ and CdZn(S_0.5Se_0.5)₂ thin films, respectively. J–V characteristic was measured for the n-CdZn(S_1−xSe_x)₂/p-CuIn(S_1−xSe_x)₂ heterojunction thin films under light illumination. The device parameters V_oc=474.4 mV, J_sc=13.21 mA/cm², FF=47.8% and η=3.5% under an illumination of 85 mW/cm² on a cell active area of 1 cm² have been calculated for solar cell fabrication. The J–V characteristic of the device under dark condition was also studied and the ideality factor was calculated which is equal to 1.9 for n-CdZn(S_0.5Se_0.5)₂/p-CuIn(S_0.5Se_0.5)₂ heterojunction thin films.     

Performance of p-type silicon-oxide windows in amorphous silicon solar cell

a-SiO_x films have been prepared using silane and pure oxygen as reactive gases in plasma CVD system. Diborane was introduced as a doping gas to obtain p-type conduction silicon oxide. Infrared absorption spectra show the incorporation of Si–O stretch mode around 1000 cm⁻¹. The optical bandgap increases with the oxygen to silane gas ratio, while the electrical conductivity decreases. Hydrogenated amorphous silicon solar cells have been fabricated using p-type a-SiO_x with around 1.85 eV optical bandgap and conductivity greater than 10⁻⁷ S/cm. The measured current–voltage characteristics of the solar cells under 100 mW/cm² artificial light are V_oc=0.84 V, J_sc=14.7 mA/cm², FF=0.635 with a conversion efficiency of 7.84%.     

Photovoltaic characteristics of CuInS2/CdS solar cell by electron beam evaporation

When a CuInS₂/CdS solar cell was fabricated by depositing CdS thin film with dopant In of 1.0 at% on ternary compound CuInS₂ thin film with the lowest resistivity of 5.59 × 10⁻² Ωcm, its best result was as follows: V_oc = 461 mV, I_sc = 26.9 mA, FF = 0.685, η = 5.66% under the illumination of 100 mW/cm². And its series resistance and lattice mismatch was 5.1 Ω and 3.2%, respectively.Besides, a 4 layer structure solar cell of -CuInS₂/high -CuInS₂/high -CdS/low - CdS has been fabricated. When thickness of high - CuInS₂ was 0.2 μm, its best result was as follows: V_oc = 580 mV, I_sc = 30.6 mA, FF = 0.697, η = 8.25%. An its series resistance and lattice mismatch were 4.3 Ω and 2.8%, respectively.     

Semiconductor-sensitized solar cells based on nanocrystalline In2S3/In2O3 thin film electrodes

A possibility of semiconductor-sensitized thin film solar cells have been proposed. Nanocrystalline In₂S₃-modified In₂O₃ electrodes were prepared with sulfidation of In₂O₃ thin film electrodes under H₂S atmosphere. The band gap (E_g) of In₂S₃ estimated from the onset of the absorption spectrum was approximately 2.0 eV. The photovoltaic properties of a photoelectrochemical solar cell based on In₂S₃/In₂O₃ thin film electrodes and I⁻/I₃⁻ redox electrolytes were investigated. This photoelectrochemical cell could convert visible light of 400–700 nm to electron. A highly efficient incident photon-to-electron conversion efficiency (IPCE) of 33% was obtained at 410 nm. The solar energy conversion efficiency, η, under AM 1.5 (100 mW cm⁻²) was 0.31% with a short-circuit photocurrent density (J_sc) of 3.10 mA cm⁻², a open-circuit photovoltage (V_oc) of 0.26 V, and a fill factor ( ff ) of 0.38.     

Photosensitization of nanocrystalline TiO2 films by a polymer with two carboxylic groups, poly (3-thiophenemalonic acid)

Photovoltaic devices were assembled using a conducting polymer; poly (3-thiophenemalonic acid) sensitized TiO₂ electrodes and an electrolyte containing I₃⁻/I⁻ redox couple. This cell exhibited a short-circuit photocurrent (J_sc) of 6.65 mA cm⁻², an open circuit voltage (V_oc) of 355 mV and an efficiency of 1.5% under the illumination of 100 mW cm⁻² (AM 1.5). Addition of an ionic liquid, 1-methyl 3-n-hexylimidazolium iodide, into the electrolyte led to an improvement in the cell performances, achieving an overall efficiency of 1.8% under the same illumination. The average cell characteristics of the later devices are , with a fill factor of 0.65.     

Influence of alkylpyridine additives in electrolyte solution on the performance of dye-sensitized solar cell

The influence of alkylpyridines additive to an I⁻/I₃⁻ redox electrolyte in acetonitrile on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell was studied. I–V measurements were performed using more than 30 different alkylpyridines. The alkylpyridine additives showed a significant influence on the performance of the cell. All the additives decreased the short-circuit photocurrent (J_sc), but most of the alkylpyridines increased the open-circuit photovoltage (V_oc) and fill factor (ff) of the solar cell. The results of the molecular orbital calculations suggest that the dipole moment of the alkylpyridine molecules correlate with the J_sc of the cell. These results also suggest that both the size and ionization energy of pyridines correlate with the V_oc of the cell. Under AM 1.5 (100 mW/cm²), the highest solar energy conversion efficiency (η) of 7.6% was achieved by using 2-propylpyridine as an additive, which was more effective than the previously reported additive, 4-t-butylpyridine.     

Large-area high efficiency single crystalline silicon solar cells

This paper reports on a 100 cm² single crystalline silicon solar cell with a conversion efficiency of 19.44% (J_sc = 37.65 mA/cm², V_oc = 638 mV, FF = 0.809). The cell structure is as simple as only applying the textured surface, oxide passivation, and back surface field by the screen printing method. The comparison between cell performances of the CZ (Czochralski) and FZ (Floating zone) silicon substrates was investigated. The higher efficiency cells were obtained for the FZ substrate rather than the CZ substrate. The influence of the phosphorus concentration of the emitter on the cell efficiency has also been investigated. A good result was obtained when the surface concentration of phosphorus was 3 × 10²⁰ cm⁻³ and the junction depth was about 0.6 μm.     

Preparation and properties of CdS/CdTe thin film solar cell produced by periodic pulse electrodeposition technique

CdS/CdTe solar cells have been prepared by periodic pulse electrodepositionmethod. 10.8% efficient cell was made with open circuit voltage (V_oc)≈753mV, short-circuit current (J_sc)≈23.6 mA/cm² and fill factor (FF)≈0.61. Current-voltage-temperature measurments showed the variation of ideality factor (A) from 1.88 at 344 K to 4.49 at 202 K whereas voltage factor (α) was almost constant above 276 K. The junction transport is possibly dominated by a tunneling mechanism. Capacitance measurements gave the value of diffusion potential as 1.2 eV, ionized charged density as 5.9 × 10¹⁵ cm⁻³ and number of interface states (N_IS) as 2.8 × 10¹¹ cm⁻² eV⁻¹ at zero volt bias. Measurements of open circuit voltage (V_oc) with temperature gave the value of barrier height as 1.42 eV.     

Bulk p-CuInSe2 photo-electrochemical solar cells

Dense CuInSe₂ of high quality, prepared by the fusion technique in evacuated quartz ampoule from stoichiometric melt, crystallizes in the chalcopyrite structure. Compositional analysis carried out by secondary ion mass spectrometry (SIMS) and energy dispersive spectroscopy (EDS) indicates a uniform distribution of elements through the depth and a composition close to the stoichiometry. The diffuse reflectance spectrum gives a band gap at 0.94 eV. The electrical conductivity follows an Arrhenius-type law with activation energy of 23 meV in conformity with polarons hopping. Above 320 °C, CuInSe₂ undergoes an irreversible oxidation. The thermal variation of the thermopower indicates p-type behavior attributed to copper deficiency and a hole mobility μ_300 K of 0.133 cm² V⁻¹ s⁻¹, thermally activated. In KCl media, the compound exhibits an excellent chemical stability with a corrosion rate of 8 μmol cm⁻² month⁻¹. The photo-electrochemical properties, investigated for the first time on the ingots, confirm the p-type conductivity. From the capacitance measurements, the flat band potential (V_fb=−0.62V_SCE) and the holes density (N_A=4×10¹⁷ cm⁻³) were determined. The valence band, located at 4.43 eV below vacuum, is made up of mainly Se orbital with little admixture of Cu character. The change of the electrolyte causes a variation in the potential V_fb (dV_fb/dpH=−0.058 V pH⁻¹) indicating strong OH⁻ adsorption. The fill factor in S²⁻ media was found to be 0.54; such result was corroborated by semi-logarithmic plots.     

p-doped μc-Si:H window layers prepared by hot-wire CVD for amorphous solar cell application

We report on boron-doped μc-Si:H films prepared by hot-wire chemical vapor deposition (HWCVD) using silane as a source gas and trimethylboron (TMB) as a dopant gas and their incorporation into all-HW amorphous silicon solar cells. The dark conductivity of these films was in the range of 1–10 (Ω cm)⁻¹. The open circuit voltage V_oc of the solar cells was found to decrease from 840 mV at low hydrogen dilution H-dil=91% to 770 mV at high H-dil =97% during p-layer deposition which can be attributed to the increased crystallinity at higher H-dil and to subsequent band edge discontinuity between μc-Si:H p- and amorphous i-layer. The short circuit current density J_sc and the fill factor FF show an optimum at an intermediate H-dil and decrease for the highest H-dil. To improve the conversion efficiency and the reproducibility of the solar cells, an amorphous-like seed layer was incorporated between TCO and the bulk p-layer. The results obtained until now for amorphous solar cells with and without the seed layer are presented. The I–V parameters for the best p–i–n solar cell obtained so far are J_sc=13.95 mA/cm², V_oc=834 mV, FF=65% and η=7.6%, where the p-layers were prepared with 2% TMB. High open circuit voltages up to 847 mV could be achieved at higher TMB concentrations.