Joint effect of halides and ethanol extract of <Emphasis Type="Italic">Lasianthera africana</Emphasis> on inhibition of corrosion of mild steel in H<Subscript>2</Subscript>SO<Subscript>4</Subscript>

Inhibitive and adsorption properties of ethanol extract of Lasianthera africana for inhibition of corrosion of mild steel in H₂SO₄ were studied using gravimetric, thermometric, gasometric, and infrared (IR) methods. The extract was found to be a good inhibitor of corrosion of mild steel in H₂SO₄. Inhibitive properties of the extract were attributed to enhancement in adsorption of the inhibitor on mild-steel surface by saponin, alkaloid, tannin, flavanoid, cardiac glycoside, and anthraquinone (present in the extract). Also, adsorption of the inhibitor was found to be exothermic, spontaneous, and consistent with assumptions of Langmuir and Temkin adsorption isotherms. Synergistic study revealed that, of the investigated halides, only KCl may enhance adsorption of the inhibitor, whereas KBr and KI antagonized its adsorption. Based on the decrease in efficiency of the inhibitor with temperature, with values of activation energy and free energy of adsorption below the threshold values of −40 and 80 kJ mol⁻¹, respectively, a physical adsorption mechanism has been proposed for adsorption of ethanol extract of Lasianthera africana on the surface of mild steel.     

Electrocatalytic reduction of hydrogen peroxide at nanostructured copper modified electrode

The electrocatalytic reduction of hydrogen peroxide (H₂O₂) has been studied at nanostructured copper (Cu_nano) modified glassy carbon (GC/Cu_nano) electrode in phosphate buffer (pH 7.2). The electrical properties of GC/Cu_nano modified electrodes were studied by electrochemical impedance spectroscopy (EIS). Surface and electrochemical characterization were carried out by using atomic force microscopy (AFM) and cyclic voltammetry. A well-defined H₂O₂ reduction signal, which is due to mediation of a surface active site redox transition exhibits at the GC/Cu_nano electrode. The Cu_nano is acting as a bridge without the aid of any other electron mediator, which enables the direct electron transfer between the modified electrode and the substrate. The results are compared with bulk copper macroelectrode and emphasized the efficiency of the Cu_nano modified electrode. Systematic investigations were made to optimize the experimental parameter, such as applied potential (E_app) for copper electrodeposition. The calibration curve obtained from chronoamperometric studies was found to be linear in the range 0.5 to 8.0 μM H₂O₂ with a detection limit of ca.10 nM (S/N = 3) at the GC/Cu_nano electrode. The modified electrode is stable for 1 week in phosphate buffer after repetitive measurements.     

Effect of copolymer ratio on hydrolytic degradation of poly(lactide-co-glycolide) from drug eluting coronary stents

The in vitro hydrolytic degradation behavior of poly(d,l-lactide-co-glycolide) (PLGA) has been systematically investigated from the drug eluting coronary stents with respect to different copolymer compositions. The drug-polymer coated stents were incubated in phosphate buffer saline (pH 7.4) at 37 °C and 120 rpm up to 12 months to facilitate hydrolytic degradation. Gel permeable chromatography, differential scanning calorimetry and scanning electron microscopy were employed to characterize their degradation profiles. The study supports the bulk degradation behavior for PLGA from coated stents. Molecular weight of polymer decreased immediately after immersion in PBS but mass loss was not observed during first few days. The rate of hydrolytic degradation was influenced by copolymer ratio, i.e., degradation of 50:50 PLGA was fastest followed by 65:35 PLGA and 75:25 PLGA. The drug release from PLGA coated stent followed biphasic pattern which was governed by surface dissolution and diffusion of drug rather than polymer degradation.     

Glass transition behavior and dynamic fragility in polylactides containing mobile and rigid amorphous fractions

The segmental dynamics of polylactide chains covering the T_g − 30 °C to T_g + 30 °C range was studied in absence and presence of a crystalline phase by dynamic mechanical analysis (DMA) using the framework provided by the WLF theory and the Angell's dynamic fragility concept. An appropriate selection of stereoisomers combined with a thermal conditioning strategy to promote crystallization (above T_g) or relaxation of chains (below T_g) was revealed as an efficient method to tune the ratio of the rigid and mobile amorphous phases in polylactides. A single bulklike mobile amorphous phase was taken for poly(d,l-lactide) (PDLLA). In turn three phases, comprising a mobile amorphous fraction (MAF, X_MA), a rigid amorphous fraction (RAF, X_RA) and a crystalline fraction (X_c) were determined in poly(l-lactide) (PLLA) by modulated differential scanning calorimetry (MDSC) according to a three-phase model. The analysis of results confirms that crystallinity and RAF not only elevate the T_g and the breadth of the glass transition region but also yields an increase in dynamic fragility parameter (m) which entails the existence of a smaller length-scale of cooperativity of polylactide chains in confined environments. Consequently it is proposed that crystallinity is acting in polymeric systems as a topological constraint that, preventing longer range dynamics, provides a faster segmental dynamics by the temperature dependence of relaxation times according to the strong-fragile scheme.     

Ring-opening polymerization of six-membered cyclic esters catalyzed by tetrahydroborate complexes of rare earth metals

Catalytic behavior of tetrahydroborate complexes of rare earth metals, Ln(BH₄)₃(THF)_x (1: Ln = La, x = 3; 2: Ln = Pr, x = 2; 3: Ln = Nd, x = 3; 4: Ln = Sm, x = 3; 5: Ln = Y, x = 2.5; 6: Ln = Yb, x = 3), for ring-opening polymerization (ROP) of six-membered cyclic esters, δ-valerolactone (VL) and d,l-lactide (d,l-LA), was studied. The controlled polymerization of VL with 1-6 proceeded in THF at 60 °C. The catalytic activities of these complexes for the ROP of VL were observed to be in order of the ionic radii of the metals: 1(La) ≥ 2(Pr) ≥ 3(Nd) > 4(Sm) > 5(Y) > 6(Yb). The obtained polymers were demonstrated to be hydroxy-telechelic by ¹H NMR and MALDI-TOF MS spectroscopy. The controlled ROP of d,l-LA also proceeded by these complexes. The activities of these complexes for the d,l-LA ROP were also in order of the ionic radii of the metals.     

Properties of l-tyrosine based polyphosphates pertinent to potential biomaterial applications

Since their introduction by Kohn and Langer et al. in 1984, l-tyrosine based ‘pseudo’ poly(amino acids) have undergone extensive research in the area of polymeric biomaterials. Starting from l-tyrosine based diphenolic monomers, polyiminocarbonates, polycarbonates and polyarylates have been developed by Kohn and co-workers and are being investigated for potential orthopedic biomaterial applications. Mao et al. have reported development of l-tyrosine based polyphosphates and polyphosphonates in a patent, however, detailed structural and physico-chemical characterization studies on such polymers have not been reported yet. For the purpose of the current paper, using a novel solid phase process for synthesis of l-tyrosine based diphenolic monomers and adapting the polymerization process described by Mao et al., l-tyrosine based polyphosphates were developed and investigated for their pertinent bioengineering properties. The properties investigated consist of chemical solubility, hydrophilicity and hydrolytic degradation. The results of this investigation are crucial to validate further investigation of biomaterial applications of these polymers.     

Electrocatalytic oxidation of some amino acids on a nickel-curcumin complex modified glassy carbon electrode

This study investigated the electrocatalytic oxidation of alanine, l-arginine, l-phenylalanine, l-lysine and glycine on poly-Ni(II)-curcumin film (curcumin: 1,7-bis [4-hydroxy-3-methoxy phenyl]-1,6-heptadiene-3,5-dione) electrodeposited on a glassy carbon electrode in alkaline solution. The process of oxidation and its kinetics were established by using cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy techniques. Voltammetric studies indicated that in the presence of amino acids the anodic peak current of low valence nickel species increased, followed by a decrease in the corresponding cathodic current. This indicates that amino acids were oxidized on the redox mediator which was immobilized on the electrode surface via an electrocatalytic mechanism. Using Laviron's equation, the values of α and k_s for the immobilized redox species were determined as 0.43 ± 0.03 and 2.47 ± 0.02 × 10⁶ s⁻¹, respectively. The rate constant, the electron transfer coefficient and the diffusion coefficients involved in the electrocatalytic oxidation of amino acids were determined.     

Functionalized micelles from new ABC polyglycidol-poly(ethylene oxide)-poly(d,l-lactide) terpolymers

New ABC type terpolymers of poly(ethoxyethyl glycidyl ether)/poly(ethylene oxide)/poly(d,l-lactide) were obtained by multi-mode anionic polymerization. After successive deprotection of the ethoxyethyl groups from the first block, highly hydroxyl functionalized copolymers of polyglycidol/poly(ethylene oxide)/poly(d,l-lactide) were obtained. These copolymers form elongated ellipsoidal micelles by direct dissolution in water. The micelles consist of a poly(d,l-lactide) core and stabilizing shell of polyglycidol/poly(ethylene oxide). The hydroxyl groups of polyglycidol blocks situated at the micelle surface provide high functionality, which could be engaged in further chemical modification resulting in a potential drug targeting agents. The micellization process of the copolymers in aqueous media was studied by hydrophobic dye solubilization, static and dynamic light scattering, and transmission electron microscopy.     

Spherulite growth of l-lactide copolymers: Effects of tacticity and comonomers

The spherulite growth behavior and mechanism of l-lactide copolymers, poly(l-lactide-co-d-lactide) [P(LLA-DLA)], poly(l-lactide-co-glycolide) [P(LLA-GA)], and poly(l-lactide-co-ε-caprolactone) [P(LLA-CL)] have been studied using polarization optical microscopy in comparison with poly(l-lactide) (PLLA) having different molecular weights to elucidate the effects of incorporated comonomer units. The incorporation of comonomer units reduced the radius growth rate of spherulites (G) and increased the induction period of spherulite formation (t_i), irrespective of the kind of comonomer unit. Such effects became remarkable with the content of comonomers. At a crystallization temperature (T_c) of 130 °C, the disturbance effects of comonomers on the spherulite growth decreased in the following order: d-lactide>glycolide>ε-caprolactone, when compared at the same comonomer unit or reciprocal of averaged l-lactyl unit sequence length (l_l). The t_i estimation indicated that the glycolide units have the lowest disturbance effects on the formation of spherulite (crystallite) nuclei. The PLLA having the number-average molecular weight (M_n) exceeding 3.1×10⁴ g mol⁻¹ showed the transition from regime II to regime III at T_c=120 °C, whereas PLLA with the lowest M_n of 9.2×10³ g mol⁻¹ crystallized solely in regime III kinetics and the copolymers excluding P(LLA-DLA) with 3% of d-lactide units crystallized solely according to regime II kinetics. The nucleation and front constant for regime II and III [K_g(II), K_g(III), G₀(II), and G₀(III), respectively] estimated with each (not with a fixed for high-molecular-weight PLLA) decreased with increasing the amount of defects per unit mass of the polymer for crystallization, i.e. with increasing the comonomer content and the density of terminal group through decreasing the molecular weight.     

Broadband dielectric spectroscopic characterization of the hydrolytic degradation of carboxylic acid-terminated poly(d,l-lactide) materials

Broadband dielectric spectroscopy was used to examine carboxylic acid-terminated poly(d,l-lactide) samples that were hydrolytically degraded in 7.4 pH phosphate buffer solutions at 37 °C. The dielectric spectral signatures of degraded samples were considerably more distinct than those of undegraded samples and a T_g-related relaxation associated with long range chain segmental mobility was seen. For both degraded and undegraded samples, a relaxation peak just beneath a DSC-based T_g was observed, which shifts to higher frequency with increasing temperature. Thus, this feature is assigned as the glass transition as viewed from the dielectric relaxation perspective. Linear segments on log-log plots of loss permittivity vs. frequency, in the low frequency regime, are attributed to d.c. conductivity. An upward shift in relaxation peak maximum, f_max, observed especially after 145 d of immersion in buffer, implies a decrease in the time scale of long range segmental motions with increased degradation time.Permittivity data for degraded and undegraded materials were fitted to the Havriliak-Negami equation with subtraction of the d.c. conductivity contribution to uncover pure relaxation peaks. Parameters extracted from these fits were used to construct Vogel-Fulcher-Tammann-Hesse (VFTH) curves and distribution of relaxation time, G(τ), curves for all samples. It was seen that the relaxation times for the α-transition in both degraded and undegraded samples showed VFTH temperature behavior. G(τ) curves showed a general broadening and shift to lower τ with degradation, which can be explained in terms of a broadening of molecular weight within degraded samples and faster chain motions.     

Dielectric study on dynamics and conformation of poly(d,l-lactic acid) in dilute and semi-dilute solutions

Fractionated samples of d,l-poly(lactic acid) (PLA) were prepared and the dielectric normal mode relaxation was studied for dilute and semi-dilute solutions of the PLA in a good solvent benzene. Results indicate that in the dilute regime the normal mode relaxation time is proportional to [η]M_w in agreement with the Rouse-Zimm theory, where [η] and M_w denote the intrinsic viscosity and weight average molecular weight, respectively. The dielectric relaxation strength which is proportional to the mean square end-to-end distance 〈r²〉 increases with increasing M_w with the power of 2ν, where ν is the excluded volume parameter determined from [η]. The relaxation time in the semi-dilute regime increases with increasing concentration C due to increases of the entanglement density and the friction coefficient. The relaxation time corrected to the iso-friction state agrees approximately with the dynamic scaling theories. The relaxation strength decreases with increasing concentration indicating that 〈r²〉 decreases on account of the screening of the excluded volume effect. The concentration dependence of 〈r²〉 agrees approximately with the scaling theory proposed by Daoud and Jannink.     

Hydrolytic degradation of poly(d,l-lactide) as a function of end group: Carboxylic acid vs. hydroxyl

d,l-Lactide was initiated with 1,4-butanediol in the presence of stannous octoate catalyst to provide hydroxyl-terminated poly(d,l-lactide) at 5000 and 20,000 g/mol. Portions of these materials were reacted with succinic anhydride in the presence of 1-methylimidazole to convert the hydroxyl functionality to succinic acid-terminated polymers in relatively high yield. The four materials were placed in a 7.4 pH buffered saline solution at 37 °C and monitored up to 180 days for their relative moisture uptake and weight loss behaviors. Carboxylic acid functionality displayed a dramatic effect on the moisture uptake behaviors for the 5000 and 20,000 g/mol polymers when compared to their respective hydroxyl functional materials. Carboxylic acid functionality significantly increased the hydrolytic degradation rate and mass loss behavior for the 5000 g/mol material, but did not affect the hydrolytic degradation rate for the higher molecular weight sample. These results suggest that moisture uptake is not the rate limiting step for the hydrolytic degradation high molecular weight poly(d,l-lactide).     

Poly(d,l-lactide)/poly(methyl methacrylate) interpenetrating polymer networks: Synthesis, characterization, and use as precursors to porous polymeric materials

The use of semi-hydrolyzable oligoester-derivatized interpenetrating polymer networks (IPNs) as nanostructured precursors provides a straightforward and versatile approach toward mesoporous networks. Different poly(d,l-lactide) (PLA)/poly(methyl methacrylate) (PMMA)-based IPNs were synthesized by resorting to the so-called in situ sequential method. The PLA sub-network was first generated from a dihydroxy-telechelic PLA oligomer via an end-linking reaction with Desmodur^® RU as a triisocyanate cross-linker. Subsequently, the methacrylic sub-network was created by free-radical copolymerization of methyl methacrylate (MMA) and a dimethacrylate (either bisphenol A dimethacrylate or diurethane dimethacrylate) with varying compositions (initial MMA/dimethacrylate composition ranging from 99/1 to 90/10 mol%). Both cross-linking processes were monitored by real-time infrared spectroscopy. The microphase separation developed in IPN precursors was investigated by differential scanning calorimetry (DSC). Furthermore, the quantitative hydrolysis of the PLA sub-network, under mild basic conditions, afforded porous methacrylic structures with pore sizes ranging from 10 to 100 nm -at most- thus showing the effective role of cross-linked PLA sub-chains as porogen templates. Pore sizes and pore size distributions were determined by scanning electron microscopy (SEM) and thermoporometry via DSC measurements. The mesoporosity of residual networks could be attributed to the good degree of chain interpenetration associated with both sub-networks in IPN precursors, due to their peculiar interlocking framework.     

Improved preparative electrochemical oxidation of d-glucose to d-glucaric acid

The 2,2,6,6-tetramethyl-1-piperidinyloxy free radical (TEMPO) mediated electrochemical oxidation of d-glucose to d-glucaric acid on a synthetically useful scale is reported. Using TEMPO and a graphite felt anode combined with a stainless steel cathode, d-glucose was oxidized under different conditions (pH, temperature, co-oxidant), and the reaction outcomes were analyzed. Optimized conditions for such oxidation are provided along with few new interesting results unique to this reaction, such as the appearance of a novel triacid.     

Synthesis and characterization of poly(l-glutamic acid)-block-poly(l-phenylalanine)

Poly(γ-benzyl l-glutamate)-block-poly(l-phenylalanine) was prepared via the ring opening polymerization of γ-benzyl l-glutamate N-carboxyanhydride and l-phenylalanine N-carboxyanhydride using n-butylamine·HCl as an initiator for the living polymerization. Polymerization was confirmed by ¹H-nuclear magnetic resonance spectroscopy and matrix assisted laser desorption ionization time of flight mass spectroscopy. After deprotection, the vesicular nanostructure of poly(l-glutamic acid)-block-poly(l-phenylalanine) particles was examined by transmission electron microscopy and dynamic light scattering. The pH-dependent properties of the nanoparticles were evaluated by means of ζ-potential and transmittance measurements. The results showed that the block copolypeptide could be prepared using simple techniques. Moreover, the easily prepared PGA-PPA block copolypeptide showed pH-dependent properties due to changes in the PGA ionization state as a function of pH; this characteristic could potentially be exploited for drug delivery applications.     

Separation of phenylalanine racemates using d-phenylalanine imprinted microbeads as HPLC stationary phase

A successful enantioseparation of d,l-phenylalanine (Phe) was achieved for the first time by using d-Phe imprinted P(MAA-co-EGDMA) microbeads as HPLC stationary phase. The d-Phe imprinted microbeads were prepared by a novel modified suspension polymerization method without derivatization of the water-soluble template molecule. This preparation method was employed in order to capture template molecules in organic phase droplets during polymerization. The prepared d-Phe imprinted P(MAA-co-EGDMA) microbeads were packed into an empty stainless steel column, which was used for the separation of the Phe enantiomers. The selection of a suitable mobile phase, mobile phase composition, pH and flow rate were investigated for determining the best resolution of the Phe enantiomers. Baseline separation was achieved using an organic–aqueous buffer (EtOH–acetate buffer) solution as a mobile phase. Separation factors of more than 2.56, with a resolution of 1.38, were obtained with a mobile phase containing 9–18% (v/v) EtOH in a 0.030 M acetate buffer solution. d-Phe imprinted microbeads were superior to the majority of the reported molecularly imprinted polymers with respect to chiral separation abilities. The column backpressure was less than 300 psi.     

Crystalline,Thermal, and Biodegradable Properties of Poly(L-Lactic Acid)/Poly(D-Lactic Acid)/POSS Melt Blends

A ternary nanocomposite consisting of poly(L-lactic acid) (PLLA), poly(D-lactic acid) (PDLA), and epoxy cyclohexyl polyhedral oligomeric silsesquioxane (e-POSS) was prepared by reactive blending method. Scanning electron microscopy revealed that the feeding of three compositions in batches, i.e., PDLA incorporation at different times, was more beneficial for the even dispersion of POSS in matrix. POSS introduction improved the homocrystallinity and stereocomplex of the blends. Rheological properties and heat resistance were enhanced, which indicated potential extensive application of PLLA-based materials. The optimization of degradation stability in saline buffer was attributed to the various hydrophobic properties of blends caused by POSS structure.     

Structure, mechanical properties and degradation behaviors of the electrospun fibrous blends of PHBHHx/PDLLA

Blends of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) and poly(d,l-lactic acid) (PDLLA) with different ratios were fabricated into fibrous membranes by electrospinning processes. Suggested by DSC, WAXD, and SAXS results, the molecular chains of PHBHHx and PDLLA were partially mixed in the amorphous phase, PDLLA didn’t affect the growth of PHBHHx crystalline phase, and PDLLA was excluded from PHBHHx lamella stacks, i.e. in form of interstack segregation, in the blend fibrous matrix. The mechanical properties of the electrospun fibrous membranes depended on the orientation of fibers in the membranes. The electrospun membranes had higher elongation; furthermore, the tensile strength and modulus of the fibers within the membranes were higher than the corresponding cast membranes. As the content of PDLLA increased, the electrospun fibrous membranes of the blends showed higher elongation and lower tensile modulus due to the decreased number of lamellae. According to the change of molecular weight distribution, both PHBHHx and PDLLA portions in the electrospun blend membranes followed bulk erosion and PDLLA degraded faster than PHBHHx during the degradation process. The morphology change of the electrospun fibrous blends during the hydrolytic degradation indicated that the degradation behaviors were strongly influenced by the miscibility and the structural phase segregation of PHBHHx/PDLLA blend in the electrospun fibers.     

Gold nanowires and the effect of impurities

Metal nanowires and in particular gold nanowires have received a great deal of attention in the past few years. Experiments on gold nanowires have prompted theory and simulation to help answer questions posed by these studies. Here we present results of computer simulations for the formation, evolution and breaking of very thin Au nanowires. We also discuss the influence of contaminants, such as atoms and small molecules, and their effect on the structural and mechanical properties of these nanowires.