共查询到20条相似文献,搜索用时 421 毫秒
1.
高杆灯基座紧固地脚螺栓抗风荷载时承受能力的计算,一般是先提出假设的地脚螺栓的允许直径,再以这种螺栓在不控制预紧力的条件下所承受的静荷载时的轴向拉力加以验算。这里必须先计算出高杆灯所在地区有可能经受到的其最大风荷载为准则(注)。例如:经计算得知,某台高... 相似文献
2.
富拉尔基第二发电厂1号炉省煤器改造后,结构荷重增加25%,为此对原结构在荷载和内压作用下,各部件的结构力、力矩、应力和强度等进行了分析并提出了一整套计算方法。 相似文献
3.
将白噪声型的宽频带随机扰力概念应用于钢球磨煤机弹簧隔振基础的设计中,结合大型火力发电厂钢球磨煤机弹簧隔振基础的设计,介绍了该基础的设计方法、钢球磨煤机弹簧隔振效率的计算以及通过弹簧隔振基础传递到基础下部动荷载的计算. 相似文献
4.
对于非承重墙下条形基础宽度的计算,往往忽略了承重墙与非承重墙相互交接处的荷载叠加效应,本文根据砖砌体结构的传力特性对这方面作了有益的探讨,并推荐了参考设计方法。 相似文献
5.
针对刚性基础下"全部或部分基桩竖向刚度各不相同""同一根基桩竖向抗拔刚度与抗压刚度不相同"时桩顶竖向力计算问题,通过分析,给出完整的桩顶竖向力计算公式和相应的"基桩竖向刚度迭代算法",以求解基桩顶部竖向力;在此基础上,针对诸如承受风荷载等需要考虑水平荷载作用方向问题的桩基础,给出桩顶竖向力随水平荷载作用方向变化而变化的自动算法,并编制了相应的计算程序,建立刚性承台桩基础基桩变刚度设计技术.实际工程中,当刚性基础下基桩竖向刚度存在差异分布时,在不同方向水平荷载作用下,桩顶竖向力控制值的计算相当复杂;所编制的计算程序可以较好地解决这个问题,为工程设计提供了一种准确、高效的分析工具. 相似文献
6.
7.
单个集中荷载作用下架空线张力计算 总被引:1,自引:0,他引:1
根据输电线路工程架线施工的实际工程需要,建立了单个集中荷载作用下架空线计算的数学模型,进行了程序设计,解决了在集中荷载作用下架空线计算的难题。 相似文献
8.
综合考虑高压输电线路直线塔和耐张塔导地线设计荷载的计算过程,采用Visual C++语言设计和实现了导地线设计荷载的自动计算程序.深入剖析电气荷载向节点荷载的转换过程,给出了直线塔V串挂线形式的荷载转换方法和计算公式.该程序具有交互性友好的界面,可以大大节省铁塔结构设计人员的工作量. 相似文献
9.
10.
输电线设计覆冰荷载计算方法的对比分析 总被引:3,自引:2,他引:3
为了使重冰区线路设计覆冰荷载的计算方法与国际标准接轨,此文以3个长期预测输电线覆冰的气象站的资料,将1991年IEC826-4法与我国现用的PⅢ型法进行计算对比分析,供设计覆冰荷载计算时参考。 相似文献
11.
电接触材料在工作过程中会受到机械磨损、环境腐蚀及电弧侵蚀,其中,电弧侵蚀对电接触材料影响最大,它是影响接触材料的电寿命和可靠性的最重要因素。笔者对采用熔渗法制备的CuCr50与电弧法制备的CuCr45电接触材料分别进行DC 50 V,20、30、40、50 A的电接触试验,并通过扫描电镜观察材料在电弧侵蚀后的形貌,对这两种材料在直流、阻性负载条件下的电弧侵蚀特征进行对比研究。结果表明,CuCr45与CurCr50在DC 50 V,20、30、40、50 A条件下,材料都由阳极向阴极转移;之后归纳出电弧侵蚀后两种材料的表面形貌特征,最后分析了两种材料的燃弧能量与熔焊力。 相似文献
12.
波动性负荷在运行过程中会向公用电网注入大量的谐波和间谐波,严重影响了电网的安全稳定运行。GB/T 17626.30规定对每一个待测参数都有Class A、S和B三类测量方法,而国内的电能质量测试仪器长期存在不同仪器采用不同测量方法导致测量结果互有差异的问题。基于Class A、S和B三类谐波测量方法的定义和算法,结合点焊机和电弧炉两种典型波动性负荷的实测数据,分析并对比了此三类测量方法在谐波测量中的最大值和95%概率大值的差异性。最后从实际工程应用的角度,给出了三类测量方法的适用场合和相关结论。 相似文献
13.
14.
针对电力系统短期负荷预测的特点,以及人工神经网络的自学习和复杂的非线性拟合能力,将人工神经网络的BP、Elman、RBF三种模型用于短期负荷预测,建立了短期电力负荷预测模型,综合考虑气象、天气等影响负荷因素进行短期负荷预测.某电网实际预测结果表明,RBF比BP、Elman有更好的预测精度,更快的速度. 相似文献
15.
16.
E. V. Belousov A. N. Shishkov A. N. Gorozhankin A. E. Bychkov 《Russian Electrical Engineering》2015,86(12):712-715
Ways to reduce radial loads on the bearings of electric machines with an electric traction drive are considered. An idea of compensation for radial loads is proposed, and a mathematical model of the electric motor drive with the controlled radial forces in the vertical direction is developed on the basis of a field-regulated reluctance machine. The model takes into account the influence of the vertical forces that are generated by various machine windings and wear in the mechanical part of the electric motor. Additional winding is used to appropriately assess the influence of the radial force. The maximum vertical force acting on the machine is calculated from the obtained waveforms. This fact allowed us to identify the future direction of research. Methods of mathematical modeling construct the dependence of the vertical force from the currents flowing in the windings of the electric machine. The minimum force is created when the field current changes, and the maximum force is created when the armature circuit current is varied. This indicates that the winding provides maximum compensation for the radial force. 相似文献
17.
18.
《IEEJ Transactions on Electrical and Electronic Engineering》2017,12(1):38-44
The structure of the modern wind turbine is becoming larger and more complex, with the wind rotor exceeding hundreds of meters in diameter. The blade shear force is also becoming increasingly serious below the rated wind speed, which leads to structure fatigue loads and instability of the generator power. For improving the dynamic performance of large wind turbines, it was proposed that individual pitch control (IPC) method was operated below the rated wind speed. In this paper, we analyze the relationship between the aerodynamic characteristics of blades and the nonlinear time‐varying pitch control system based on wind shear and the tower shadow effect. The combination of IPC and torque control is used to optimize the control mode of the wind turbine. By fine‐tuning the pitch angle, the unbalanced force on the wind rotor was relieved to achieve the purpose of mitigating fatigue loads. Finally, our experimental results prove the validity of the proposed IPC method below the rated wind speed by showing that it can improve power quality and reduce fatigue loads of the key components without reducing the generator output power. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc. 相似文献
19.
高拱坝坝基断层的处理是拱坝建基面设计中重要的一环,该处应力复杂,确定置换体、锚固体所应承受加固力比较困难。本文运用变形加固理论对高拱坝坝基断层的加固机理进行研究。变形加固理论揭示了自承力、加固力、外荷载、结构稳定性和变形之间内在的联系,指出在给定外荷载作用下,结构的加固区域就是出现不平衡力的区域,为抑制破坏所需加固力即为不平衡力的反向力。研究结果表明:坝基断层为不平衡力集中区,断层的不平衡力与断层受力相比为小量,但它关系到断层的稳定性;不平衡力的大小、方向和分布有助于确定断层的加固区域及制定合理的加固方案。 相似文献
20.
在不同弯头壁厚条件下,通过管道应力计算来考察弯头壁厚变化对管道应力、管道对设备接口推力和推力矩以及管系中弹性支吊架荷载的影响.由于弯头壁厚增加,使得管系中弯头处一次应力降低,二次应力上升,使得管系对设备接口推力和推力矩增加,且推力矩的增加尤为显著,使得管系中弹性支吊点荷载增加,支吊架弹簧跳号. 相似文献