Determination of 1600° and 1700°C. Liquidus Lines in CaO-2Al2O3 and AI2O3 Stability Fields of the System CaO—Al2O3—SiO2

The 1600° and 1700°C. liquidus lines in the CaO·2Al₂O₃ and A1₂O₃ stability fields of the system CaO-Al₂O₃-SiO₂ are determined from the chemical analyses of saturated slags at these temperatures.     

Solubility of NiO in Al2O3

Solubility of NiO in Al₂O₃ was determined by electron probe microanalysisy A diffusion couple method was used by coupling an NiO-doped Al₂O₃ polycrystal to a pure single crystal of Al₂O₃. The solubility of NiO in Al₂O₃ in air was 230 wt ppm (157 at. ppm of cations) and 170 wt ppm (116 at. ppm) at 2073 and 1973 K, respectively. The solubility of NiO in Al₂O₃ obtained in this work was compared with our previous work of the solubility of MgO in Al₂o₃.     

Structure of B2O3 and Binary Aluminoborate Melts at 1600°C

Viscosity and density data were obtained up to 1700°C for a series of binary aluminoborate melts that contained as much as 15 mole% (∼21 wt%) Al₂O₃ and up to 1620°C for pure molten B₂O₃. Large expansion coefficient decreases and a slight activation energy increase for B₂O₃ above 1400°C suggested a tightening of its structure. The addition of Al₂O₃ reduced viscosity and increased activation energy. The decreased compositional dependence of molar volume (compared to SiO₂ additions) and the increased expansion coefficients accompanying Al₂O₃ additions suggested a loosening of the O—B—O structure at 1600°C. Molar volume deviations from ideality were similar to but smaller than those for SiO₂ and GeO₂ additions at 1300°C. Microclustering of aluminum-bearing polyhedra appeared to occur at slightly higher boron atom contents than with SiO₂ and GeO₂ additions.     

Thermal Grooving of MgO and Al2O3

High-purity polycrystalline MgO and Al₂O₃ were thermally grooved at 1500° and 1600°C. Accurate techniques were developed for following the growth of a single groove. For high-purity samples growth kinetics were essentially similar to those reported in the literature but were determined to be controlled by volume diffusion. Specimens for thermal grooving were prepared from Al₂O₃ to which transition metal oxides (Fe₂O₃₉, MnO, and TiO₂), which are known to accelerate shrinkage and sintering of Al₂O₃ powder compacts, had been added; the rate of groove growth was increased remarkably by minor amounts of these additives. Control of partial pressure indicated that Fe²⁺ and Ti⁴⁺ are the species active in promoting groove growth. Substantial evidence was found for volume diffusion as the mechanism controlling groove formation.     

Superplastic Deformation in Fine-Grained MgO 2Al2O3 Spinel

Fine-grained polycrystals of MgO 2A1₂O₃ spinel were deformed to large strains at strain rates ranging from 1O^-5 to 1O^-3 s^-1 and at temperatures from 1723 to 1885 K. These polycrystals were ductile at low strain rates and high temperatures; the ductility was especially remarkable at temperatures near the solvus. The mechanism of deformation, which was determined by measuring the change of flow stress with grain size, was dislocation creep, with the stress exponent in the power-law creep equation having a value of 2.1 ± 0.4. Despite deformation of several hundred percent, the grain size remained equiaxed, and deformation led to the evolution of a grain size which depended only on the strain rate and temperature. The initial microstructure had an influence on whether the poly-crystal would fracture or flow; a small initial grain size and a supersaturated solid solution were conducive to ductile flow. The ductility is attributed to dynamic recrystallization. It is proposed that the onset of fracture and the onset of dynamic recrystallization are competitive processes. Conditions which promote dynamic recrystallization also promote ductile flow.     

Activity–Composition Relations in FeCr2O4–FeAl2O4 and MnCr2O4–MnAl2O4 Solid Solutions at 1500° and 1600°C

Activity–composition relations of FeCr₂O₄–FeAl₂O₄ and MnCr₂O₄–MnAl₂O₄ solid solutions were derived from activity–composition relations of Cr₂O₃–Al₂O₃ solid solutions and directions of conjugation lines between coexisting spinel and sesquioxide phases in the systems FeO–Cr₂O₃–Al₂O₃ and MnO–Cr₂O₃–Al₂O₃. Moderate positive deviations from ideality were observed.     

Subsolidus Phase Relationships in the System Fe2O3–Al2O3–TiO2 between 1000° and 1300°C

Subsolidus phase equilibria in the system Fe₂O₃–Al₂O₃–TiO₂ were investigated between 1000° and 1300°C. Quenched samples were examined using powder X-ray diffraction and electron probe microanalytical methods. The main features of the phase relations were: (a) the presence of an M₃O₅ solid solution series between end members Fe₂TiO₅ and Al₂TiO₅, (b) a miscibility gap along the Fe₂O₃–Al₂O₃ binary, (c) an α-M₂O₃( ss ) ternary solid-solution region based on mutual solubility between Fe₂O₃, Al₂O₃, and TiO₂, and (d) an extensive three-phase region characterized by the assemblage M₃O₅+α-M₂O₃( ss ) + Cor( ss ). A comparison of results with previously established phase relations for the Fe₂O₃–Al₂O₃–TiO₂ system shows considerable discrepancy.     

Phase Equilibria in the Pseudoternary System ZrO2−Y2O3−Cr2O3 at 1600°C in Air

The pseudoternary system ZrO₂-Y₂O₃-Cr₂O₃ was studied at 1600°C in air by the quenching method. Only one intermediate compound, YCrO₃, was observed on the Y₂O₃−Cr₂O₃ join. ZrO₂ and Y₂O₃ formed solid solutions with solubility limits of 47 and 38 mol%, respectively. The apex of the compatibility triangle for the cubic ZrO₂, Cr₂O₃, and YCrO₃ three-phase region was located at =17 mol% Y₂O₃ (83 mol% ZrO₂). Below 17 mol% Y₂O₃, ZrO₂ solid solution coexisted with Cr₂O₃. Cr₂O₃ appears to be slightly soluble in ZrO₂(ss).     

Phase Formation in the System Na2O · Al2O3-CaO · A12O3-Al2O3 at 1200°C in Air

Phase relations in the system Na₂O_· Al₂O₃-CaO· Al₂O₃-Al₂O₃ at 1200°C in air were determined using the quenching method and high-temperature X-ray diffraction. The compound 2Na₂O · 3CaO · 5Al₂O₃, known from the literature, was reformulated as Na₂O · CaO · 2Al₂O₃. A new compound with the probable composition Na₂O · 3CaO · 8Al₂O₃ was found. Cell parameters of both compounds were determined. The compound Na₂O · CaO-2Al₂O₃ is tetragonal with a = 1.04348(24) and c = 0.72539(31) nm; it forms solid solutions with Na₂O · Al₂O₃ up to 38 mol% Na₂O at 1200°C. The compound Na₂O · 3CaO · 8Al₂O₃ is hexagonal with) a = 0.98436(4) and c = 0.69415(4) nm. The compound CaO · 6Al₂O₃ is not initially formed from oxide components at 1200°C but behaves as an equilibrium phase when it is formed separately at higher temperatures. The very slow transformation kinetics between β and β "-Al₂O₃ make it very difficult to determine equilibrium phase relations in the high-Al₂O₃ part of the diagram. Conclusions as to lifetime processes in high-pressure sodium discharge lamps can be drawn from the phase diagram.     

High-Temperature Elastic Properties of Polycrystalline MgO and Al2O3

Adiabatic bulk modulus, B_s , of polycrystalline MgO and Al₂O₃ was measured from 298° to 1473°K using the resonance technique. The Grüneisen constant, calculated from the measured bulk modulus, was constant over the whole temperature range (1.53 for MgO and 1.34 for Al₂O₃). Another important parameter,     , is constant at high temperature and is 3.1 for MgO and 3.6 for Al₂O₃. The Poisson's ratio increases linearly with temperature for MgO and Al₂O₃. To describe the change of bulk modulus with temperature a theoretical equation was verified by using the foregoing constants. A practical form of this theoretical equation is where B_s⁰ is the adiabatic bulk modulus at 0°K, δ is the quantity     , γ is the Grüneisen constant, H is the enthalpy. The experimental data are described very well by this equation, which is equivalent to the empirical equation suggested by Wachtman et al., B_s^T= B_s⁰ - CT exp (-T_c/T) , where C and T_c are empirical constants.     

Bimodal Sintering of Al2O3/Al2O3 Platelet Ceramic Composites

The sintering behavior of an Al₂O₃ compact containing uniformly dispersed Al₂O₃ platelets has been investigated. The results reveal a significant decrease in the sintering rate as well as the formation of voids and cracklike defects in the presence of nonsinterable platelets. The addition of a small amount (2 vol%) of tetragonal-ZrO₂ particles enhances the sintering rate, increases end-point density (∼99.5% of theoretical density) and prevents formation of sintering defects.     

Hydration of 3CaO·Al2O3 and 3CaO·Al2O3+] Gypsum With and Without CaCl2

Paste samples of tricalcium aluminate alone, with CaCl₂, with gypsum, and with gypsum and CaCl₂ were hydrated for up to 6 months and the hydration products characterized by SEM, XRD, and DTA. Tricalcium aluminate hydrated initially to a hexagonal hydroaluminate phase which then changed to the cubic form; the transformation rate depended on the size and shape of the sample and on temperature. The addition of CaCl₂ to tricalcium aluminate resulted in the formation of 3CaO · Al₂O₃· CaCl₂·10H₂O and 4CaO · Al₂O₃· 13H₂O, or a solid solution of the two. The chloride retarded the formation of the cubic phase 3CaO · Al₂O₃· 6H₂O; the addition of gypsum resulted in the formation of monosulfoaluminate with a minor amount of ettringite. When chloride was added to tricalcium aluminate and gypsum, more ettringite was formed, although 3CaO · Al₂O₃· CaSO₄· 12H₂O and 3CaO · Al₂O₃· CaCl₂· 10H₂O were the main hydration products.     

Effect of MgO Solute on Microstructure Development in Al2O3

The effect of MgO as a solid-solution additive in the sintering of Al₂O₃ was studied. The separate effects of the additive on densification and grain growth were assessed. Magnesia was found to increase the densification rate during sintering by a factor of 3 through a raising of the diffusion rate. The grain-size dependence of the densification rate indicated control primarily by grain-boundary diffusion. Magnesia also increased the grain growth rate during sintering by a factor of 2.5. The dependence of the grain growth rate on density and grain size suggested a mechanism of surface-diffusion-controlled pore drag. It was argued, therefore, that MgO enhanced grain growth by raising the surface diffusion coefficient. The effect of MgO on the densification rate/grain growth rate ratio was, therefore, found to be minimal and, consequently, MgO did not have a significant effect on the grain size/density trajectory during sintering. The role of MgO in the sintering of alumina was attributed mainly to its ability to lower the grain-boundary mobility.     

Microstructure Development in Al2O3-Platelet-Reinforced Ce-ZrO2/Al2O3 Composites

Composites containing Ce-ZrO₂, Al₂O₃, and aligned Al₂O₃ platelets were produced by centrifugal consolidation and pressureless sintering, followed by heat treatments at 1600°C for varied duration. Constituents in the consolidated microstructures were either uniformly distributed throughout or segregated into gradient layers, depending critically on platelet content. Quantitative image analysis was used to examine microstructure development with heat treatment. Changes in the volume fraction, dimensional anisotropy, and gradient of pores and platelets, as well as changes in the phase gradient, were quantified. Microstructure development was strongly dependent on the initial microstructure design attained from suspension processing.     

Dynamic Fracture Characterization of Al2O3 and SiCw/Al2O3

The dynamic stress intensity factors, which were determined with newly developed bar impact facilities and a new data reduction procedure, for an Al₂O₃ ceramic and 29 vol% SiC_w/Al₂O₃ composite were virtually identical, thus indicating that the short SiC whiskers were ineffective under dynamic fracture. SEM studies revealed five distinct fracture morphologies with increased percentage area of transgranular fracture in both materials with rapid crack propagation. Also, the high dynamic stress intensity factor caused multiple microscopic crack planes to form and then join as the crack advanced.     

Phase Equilibria in the Ti-AI-O System at 945°C and Analysis of Ti/Al2O3 Reactions

Phase relations in the Ti-Al-O system were evaluated experimentally at 945°C. The tie lines were established using equilibrated samples with phase compositions determined by electron probe microanalysis. The phase relations were in agreement with previous estimates but the phase fields of α-Ti[O,Al] and Ti₃Al[O] were significantly different. The Ti₃Al[O] phase has a maximum solubility of 22 at. % O, corresponding to a nominal stoichiometry of Ti₃AlO, whereas the α-Ti[O,Al] phase, at a maximum O solubility of 33.33 at. %, has a negligible amount of Al in solution. The disagreement between these results and previous studies was attributed to the differences in experimental techniques for sample preparation and analysis. The reported layer sequences at the Ti/Al₂O₃ interface were evaluated based on the ternary section and the corresponding O activity diagram. The layered interfaces were found to be stable, with the evolution of the reaction products governed by the thickness of the initial Ti layer and the O partial pressure in the ambient.     

Phase Equilibria in the System CaO-MgO-B2O3 at 900°C

Phase equilibria in the system CaO-MgO-B₂O₃ were investigated at 900°C using X-ray powder diffraction techniques. With the exception of MgO-B₂O₃, the binary phases reported previously were confirmed, but no ternary phases were found. Solid solution effects were investigated for the binary phases by comparison of patterns, whereas for CaO and MgO, accurate lattice parameters were compared. No solid solutions were detected. As a result, the isothermal equilibrium diagram at 900°C reduces to three phase triangles. X-ray powder diffraction data for the calcium berates are included.     

Isothermal Section of a Cu2O–Al2O3–SiO2 Pseudo-Ternary System at 1150°C in Air

In this study, the isothermal section of a Cu₂O–Al₂O₃–SiO₂ pseudo-ternary phase diagram at 1150°C was analyzed by means of a scanning electronic microscope and powder X-ray diffraction of the quenched samples qualitatively, and the compositions of the tie-points of the tie-planes as well as their regions were determined by in situ high-temperature quantitative X-ray diffraction analysis and energy-dispersive X-ray spectroscopy. Then, the isothermal section of the Cu₂O–Al₂O₃–SiO₂ pseudo-ternary phase diagram at 1150°C was constructed; it was found that the isothermal section is composed of two single liquid-phase regions, five two-phase regions, and six three-phase regions.