InGaAs-InP mesa DHBTs with simultaneously high f/sub /spl tau// and f/sub max/ and low C/sub cb//I/sub c/ ratio

We report an InP-InGaAs-InP double heterojunction bipolar transistor (DHBT), fabricated using a conventional triple mesa structure, exhibiting a 370-GHz f/sub /spl tau// and 459-GHz f/sub max/, which is to our knowledge the highest f/sub /spl tau// reported for a mesa InP DHBT-as well as the highest simultaneous f/sub /spl tau// and f/sub max/ for any mesa HBT. The collector semiconductor was undercut to reduce the base-collector capacitance, producing a C/sub cb//I/sub c/ ratio of 0.28 ps/V at V/sub cb/=0.5 V. The V/sub BR,CEO/ is 5.6 V and the devices fail thermally only at >18 mW//spl mu/m/sup 2/, allowing dc bias from J/sub e/=4.8 mA//spl mu/m/sup 2/ at V/sub ce/=3.9 V to J/sub e/=12.5 mA//spl mu/m/sup 2/ at V/sub ce/=1.5 V. The device employs a 30 nm carbon-doped InGaAs base with graded base doping, and an InGaAs-InAlAs superlattice grade in the base-collector junction that contributes to a total depleted collector thickness of 150 nm.     

Efficient PDFA module using high-NA PbF/sub 2//InF/sub 3/-based fluoride fiber

The highest reported single-pass gain coefficient of 0.36 dB/mW has been achieved using a newly developed Pr/sup 3+/-doped high-NA PbF/sub 2//InF/sub 3/-based fluoride fiber, with a /spl Delta/n of 6.6%, a core diameter of 1.2 /spl mu/m and a transmission loss of 250 dB/km at 1.2 /spl mu/m. This fiber was used to construct an efficient PDFA module with a MOPA-LD. A small-signal net gain of 22.5 dB was achieved at 1.30 /spl mu/m with a pump power of 23m mW.     

Low-frequency noise in submicrometer MOSFETs with HfO/sub 2/, HfO/sub 2//Al/sub 2/O/sub 3/ and HfAlO/sub x/ gate stacks

Low-frequency noise measurements were performed on p- and n-channel MOSFETs with HfO/sub 2/, HfAlO/sub x/ and HfO/sub 2//Al/sub 2/O/sub 3/ as the gate dielectric materials. The gate length varied from 0.135 to 0.36 /spl mu/m with 10.02 /spl mu/m gate width. The equivalent oxide thicknesses were: HfO/sub 2/ 23 /spl Aring/, HfAlO/sub x/ 28.5 /spl Aring/ and HfO/sub 2//Al/sub 2/O/sub 3/ 33 /spl Aring/. In addition to the core structures with only about 10 /spl Aring/ of oxide between the high-/spl kappa/ dielectric and silicon substrate, there were "double-gate oxide" structures where an interfacial oxide layer of 40 /spl Aring/ was grown between the high-/spl kappa/ dielectric and Si. DC analysis showed low gate leakage currents in the order of 10/sup -12/A(2-5/spl times/10/sup -5/ A/cm/sup 2/) for the devices and, in general, yielded higher threshold voltages and lower mobility values when compared to the corresponding SiO/sub 2/ devices. The unified number-mobility fluctuation model was used to account for the observed 1/f noise and to extract the oxide trap density, which ranged from 1.8/spl times/10/sup 17/ cm/sup -3/eV/sup -1/ to 1.3/spl times/10/sup 19/ cm/sup -3/eV/sup -1/, somewhat higher compared to conventional SiO/sub 2/ MOSFETs with the similar device dimensions. There was no evidence of single electron switching events or random telegraph signals. The aim of this paper is to present a general discussion on low-frequency noise characteristics of the three different high-/spl kappa//gate stacks, relative comparison among them and to the Si--SiO/sub 2/ system.     

Low-frequency noise in submicrometer MOSFETs with HfO/sub 2/, HfO/sub 2//Al/sub 2/O/sub 3/ and HfAlO/sub x/ gate stacks

Low-frequency noise measurements were performed on p- and n-channel MOSFETs with HfO/sub 2/, HfAlO/sub x/ and HfO/sub 2//Al/sub 2/O/sub 3/ as the gate dielectric materials. The gate length varied from 0.135 to 0.36 /spl mu/m with 10.02 /spl mu/m gate width. The equivalent oxide thicknesses were: HfO/sub 2/ 23 /spl Aring/, HfAlO/sub x/ 28.5 /spl Aring/ and HfO/sub 2//Al/sub 2/O/sub 3/ 33 /spl Aring/. In addition to the core structures with only about 10 /spl Aring/ of oxide between the high-K dielectric and silicon substrate, there were "double-gate oxide" structures where an interfacial oxide layer of 40 /spl Aring/ was grown between the high-K dielectric and Si. DC analysis showed low gate leakage currents in the order of 10/sup -12/ A(2-5 /spl times/ 10/sup -5/ A/cm/sup 2/) for the devices and, in general, yielded higher threshold voltages and lower mobility values when compared to the corresponding SiO/sub 2/ devices. The unified number-mobility fluctuation model was used to account for the observed 1/f noise and to extract the oxide trap density, which ranged from 1.8 /spl times/ 10/sup 17/ cm/sup -3/ eV/sup -1/ to 1, 3 /spl times/ 10/sup 19/ cm/sup -3/ eV/sup -1/ somewhat higher compared to conventional SiO/sub 2/ MOSFETs with the similar device dimensions. There was no evidence of single electron switching events or random telegraph signals. The aim of this paper is to present a general discussion on low-frequency noise characteristics of the three different high-K/gate stacks, relative comparison among them and to the Si-SiO/sub 2/ system.     

Very high density RF MIM capacitors (17 fF//spl mu/m/sup 2/) using high-/spl kappa/ Al/sub 2/O/sub 3/ doped Ta/sub 2/O/sub 5/ dielectrics

Using high-/spl kappa/ Al/sub 2/O/sub 3/ doped Ta/sub 2/O/sub 5/ dielectric, we have obtained record high MIM capacitance density of 17 fF//spl mu/m/sup 2/ at 100 kHz, small 5% capacitance reduction to RF frequency range, and low leakage current density of 8.9/spl times/10/sup -7/ A/cm/sup 2/. In combination of both high capacitor density and low leakage current density, a very low leakage current of 5.2/spl times/10/sup -12/ A is calculated for a typical large 10 pF capacitor used in RF IC that is even smaller than that of a deep sub-/spl mu/m MOSFET. This very high capacitance density with good MIM capacitor characteristics can significantly reduce the chip size of RF ICs.     

Long-wavelength In/sub 0.53/Ga/sub 0.47/As-In/sub 0.52/Al/sub 0.48/As large-area avalanche photodiodes and arrays

Large-area (500-/spl mu/m diameter) mesa-structure In/sub 0.53/Ga/sub 0.47/As-In/sub 0.52/Al/sub 0.48/As avalanche photodiodes (APDs) are reported. The dark current density was /spl sim/2.5/spl times/10/sup -2/ nA//spl mu/m/sup 2/ at 90% of breakdown; low surface leakage current density (/spl sim/4.2 pA//spl mu/m) was achieved with wet chemical etching and SiO/sub 2/ passivation. An 18 /spl times/ 18 APD array with uniform distributions of breakdown voltage, dark current, and multiplication gain has also been demonstrated. The APDs in the array achieved 3-dB bandwidth of /spl sim/8 GHz at low gain and a gain-bandwidth product of /spl sim/120 GHz.     

InGaAs/InP DHBTs with 120-nm collector having simultaneously high f/sub /spl tau//, f/sub max//spl ges/450 GHz

InP/In/sub 0.53/Ga/sub 0.47/As/InP double heterojunction bipolar transistors (DHBT) have been designed for increased bandwidth digital and analog circuits, and fabricated using a conventional mesa structure. These devices exhibit a maximum 450 GHz f/sub /spl tau// and 490 GHz f/sub max/, which is the highest simultaneous f/sub /spl tau// and f/sub max/ for any HBT. The devices have been scaled vertically for reduced electron collector transit time and aggressively scaled laterally to minimize the base-collector capacitance associated with thinner collectors. The dc current gain /spl beta/ is /spl ap/ 40 and V/sub BR,CEO/=3.9 V. The devices operate up to 25 mW//spl mu/m/sup 2/ dissipation (failing at J/sub e/=10 mA//spl mu/m/sup 2/, V/sub ce/=2.5 V, /spl Delta/T/sub failure/=301 K) and there is no evidence of current blocking up to J/sub e//spl ges/12 mA//spl mu/m/sup 2/ at V/sub ce/=2.0 V from the base-collector grade. The devices reported here employ a 30-nm highly doped InGaAs base, and a 120-nm collector containing an InGaAs/InAlAs superlattice grade at the base-collector junction.     

A high f/sub OSC//f/sub T/ ratio VCO in SiGe BiCMOS technology

A 37-GHz voltage controlled oscillator (VCO) fabricated in IBM's 47-GHz SiGe BiCMOS technology is presented. The VCO achieves a phase noise of -81dBc/Hz at 1-MHz offset from the carrier while delivering an output power of -30dBm to 50 /spl Omega/ buffers. Drawing 15-mA of dc current from a 3-V power supply the VCO occupies 350/spl mu/m/spl times/280/spl mu/m of silicon area. Capacitive emitter degeneration and compact layout are used to achieve high f/sub OSC//f/sub T/ ratio.     

Electrical characteristics of 8-/spl Aring/ EOT HfO/sub 2//TaN low thermal-budget n-channel FETs with solid-phase epitaxially regrown junctions

The authors demonstrate high-performing n-channel transistors with a HfO/sub 2//TaN gate stack and a low thermal-budget process using solid-phase epitaxial regrowth of the source and drain junctions. The thinnest devices have an equivalent oxide thickness (EOT) of 8 /spl Aring/, a leakage current of 1.5 A/cm/sup 2/ at V/sub G/=1 V, a peak mobility of 190 cm/sup 2//V/spl middot/s, and a drive-current of 815 /spl mu/A//spl mu/m at an off-state current of 0.1 /spl mu/A//spl mu/m for V/sub DD/=1.2 V. Identical gate stacks processed with a 1000-/spl deg/C spike anneal have a higher peak mobility at 275 cm/sup 2//V/spl middot/s, but a 5-/spl Aring/ higher EOT and a reduced drive current at 610 /spl mu/A//spl mu/m. The observed performance improvement for the low thermal-budget devices is shown to be mostly related to the lower EOT. The time-to-breakdown measurements indicate a maximum operating voltage of 1.6 V (1.2 V at 125 /spl deg/C) for a ten-year lifetime, whereas positive-bias temperature-instability measurements indicate a sufficient lifetime for operating voltages below 0.75 V.     

Spectroscopic analysis and diode-pumped laser results of Nd:BaY/sub 2/F/sub 8/

Single crystals of monoclinic BaY/sub 2/F/sub 8/, doped with different Nd/sup 3+/ concentrations, were successfully grown by means of the Czochralski method. Here, we present a polarized infrared (IR) spectroscopic investigation and diode-pumped continuous-wave laser results in the 1 /spl mu/m wavelength region. Moreover for the first time 1.3 /spl mu/m laser emission has been characterized. Q-switching results in the 1-/spl mu/m region are also presented.     

Metal-insulator-metal RF bypass capacitor using niobium oxide (Nb/sub 2/O/sub 5/) with HfO/sub 2//Al/sub 2/O/sub 3/ barriers

A high capacitance density (C/sub density/) metal-insulator-metal (MIM) capacitor with niobium pentoxide (Nb/sub 2/O/sub 5/) whose k value is higher than 40, is developed for integrated RF bypass or decoupling capacitor application. Nb/sub 2/O/sub 5/ MIM with HfO/sub 2//Al/sub 2/O/sub 3/ barriers delivers a high C/sub density/ of >17 fF//spl mu/m/sup 2/ with excellent RF properties, while maintaining comparable leakage current and reliability properties with other high-k dielectrics. The capacitance from the dielectric is shown to be stable up to 20 GHz, and resonant frequency of 4.2 GHz and Q of 50 (at 1 GHz) is demonstrated when the capacitor is integrated using Cu-BEOL process.     

A new metal-ferroelectric (PbZr/sub 0.53/Ti/sub 0.47/O/sub 3/)-insulator (Dy/sub 2/O/sub 3/)-semiconductor (MFIS) FET for nonvolatile memory applications

Metal-ferroelectric-insulator-semiconductor (MFIS) field-effect transistors with Pb(Zr/sub 0.53/,Ti/sub 0.47/)O/sub 3/ ferroelectric layer and dysprosium oxide Dy/sub 2/O/sub 3/ insulator layer were fabricated. The out-diffusion of atoms between Dy/sub 2/O/sub 3/ and silicon was examined by secondary ion mass spectrometry profiles. The size of the memory windows was investigated. The memory windows measured from capacitance-voltage curves of MFIS capacitors and I/sub DS/-V/sub GS/ curves of MFIS transistors are consistent. The nonvolatile operation of MFIS transistors was demonstrated by applying positive/negative writing pulses. A high driving current of 9 /spl mu/A//spl mu/m was obtained even for long-channel devices with a channel length of 20 /spl mu/m. The electron mobility is 181 cm/sup 2//V/spl middot/s. The retention properties of MFIS transistors were also measured.     

DRAM plate electrode bias optimization for reducing leakage current in UV-O/sub 3/ and O/sub 2/ annealed CVD deposited Ta/sub 2/O/sub 5/ dielectric films

A new plate biasing scheme is described which allowed the use of 65% higher supply voltage without increasing the leakage current for the UV-O/sub 3/ and O/sub 2/ annealed chemical-vapor-deposited tantalum pentaoxide dielectric film capacitors in stacked DRAM cells. Dielectric leakage was reduced by biasing the capacitor plate electrode to a voltage lower than the conventionally used value of V/sub cc//2. Ta/sub 2/O/sub 5/ films with 3.9 nm effective gate oxide, 8.5 fF//spl mu/m/sup 2/ capacitance and <0.3 /spl mu/A/cm/sup 2/ leakage at 100/spl deg/C and 3.3 V supply are demonstrated.<>     

A 12 /spl times/ 12 In/sub 0.53/Ga/sub 0.47/As-In/sub 0.52/Al/sub 0.48/As avalanche photodiode array

We report a 12 /spl times/ 12 In/sub 0.53/Ga/sub 0.47/As-In/sub 0.52/Al/sub 0.48/As avalanche photodiode (APD) array. The mean breakdown voltage of the APD was 57.9 V and the standard deviation was less than 0.1 V. The mean dark current was /spl sim/2 and /spl sim/300 nA, and the standard deviation was /spl sim/0.19 and /spl sim/60 nA at unity gain (V/sub bias/ = 13.5 V) and at 90% of the breakdown voltage, respectively. External quantum efficiency was above 40% in the wavelength range from 1.0 to 1.6 /spl mu/m. It was /spl sim/57% and /spl sim/45% at 1.3 and 1.55 /spl mu/m, respectively. A bandwidth of 13 GHz was achieved at low gain.     

Reliability investigation of 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel

The authors have investigated the reliability performance of G-band (183 GHz) monolithic microwave integrated circuit (MMIC) amplifiers fabricated using 0.07-/spl mu/m T-gate InGaAs-InAlAs-InP HEMTs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel on 3-in wafers. Life test was performed at two temperatures (T/sub 1/ = 200 /spl deg/C and T/sub 2/ = 215 /spl deg/C), and the amplifiers were stressed at V/sub ds/ of 1 V and I/sub ds/ of 250 mA/mm in a N/sub 2/ ambient. The activation energy is as high as 1.7 eV, achieving a projected median-time-to-failure (MTTF) /spl ap/ 2 /spl times/ 10/sup 6/ h at a junction temperature of 125 /spl deg/C. MTTF was determined by 2-temperature constant current stress using /spl Delta/G/sub mp/ = -20% as the failure criteria. The difference of reliability performance between 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel and 0.1-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with In/sub 0.6/Ga/sub 0.4/As channel is also discussed. The achieved high-reliability result demonstrates a robust 0.07-/spl mu/m pseudomorphic InGaAs-InAlAs-InP HEMT MMICs production technology for G-band applications.     

Electrical characteristics and reliability of UV transparent Si/sub 3/N/sub 4/ metal-insulator-metal (MIM) capacitors

In this paper, we discuss the electrical characteristics and reliability of UV transparent Si/sub 3/N/sub 4/ metal-insulator-metal (MIM) capacitors. We examine film thicknesses in the range of 55 to 25 nm with capacitance densities from 1.2 ff//spl mu/m/sup 2/ to 2.8 ff//spl mu/m/sup 2/, respectively, for single MIM capacitors. A new approach for projecting the dielectric reliability of these films extends the limits of maximum operating voltage. Accounting for temperature acceleration and area scaling, the projected lifetimes can be met for a wide range of operating conditions.     

RF, DC, and reliability characteristics of ALD HfO/sub 2/-Al/sub 2/O/sub 3/ laminate MIM capacitors for Si RF IC applications

High-performance metal-insulator-metal capacitors using atomic layer-deposited HfO/sub 2/-Al/sub 2/O/sub 3/ laminate are fabricated and characterized for RF and mixed-signal applications. The laminate capacitor can offer high capacitance density (12.8 fF//spl mu/m/sup 2/) up to 20 GHz, low leakage current of 4.9/spl times/10/sup -8/ A/cm/sup 2/ at 2 V and 125/spl deg/C, and small linear voltage coefficient of capacitance of 211 ppm/V at 1 MHz, which can easily satisfy RF capacitor requirements for year 2007 according to the International Technology Roadmap for Semiconductors. In addition, effects of constant voltage stress and temperature on leakage current and voltage linearity are comprehensively investigated, and dependences of quadratic voltage coefficient of capacitance (/spl alpha/) on frequency and thickness are also demonstrated. Meanwhile, the underlying mechanisms are also discussed.     

A novel high-/spl kappa/ SONOS memory using TaN/Al/sub 2/O/sub 3//Ta/sub 2/O/sub 5//HfO/sub 2//Si structure for fast speed and long retention operation

A novel high-/spl kappa/ silicon-oxide-nitride-oxide-silicon (SONOS)-type memory using TaN/Al/sub 2/O/sub 3//Ta/sub 2/O/sub 5//HfO/sub 2//Si (MATHS) structure is reported for the first time. Such MATHS devices can keep the advantages of our previously reported TaN/HfO/sub 2//Ta/sub 2/O/sub 5//HfO/sub 2//Si device structure to obtain a better tradeoff between long retention and fast programming as compared to traditional SONOS devices. While at the same time by replacing hafnium oxide (HfO/sub 2/) with aluminum oxide (Al/sub 2/O/sub 3/) for the top blocking layer, better blocking efficiency can be achieved due to Al/sub 2/O/sub 3/'s much larger barrier height, resulting in greatly improved memory window and faster programming. The fabricated devices exhibit a fast program and erase speed, excellent ten-year retention and superior endurance up to 10/sup 5/ stress cycles at a tunnel oxide of only 9.5 /spl Aring/ equivalent oxide thickness.     

High-performance Pt/SrBi/sub 2/Ta/sub 2/O/sub 9//HfO/sub 2//Si structure for nondestructive readout memory

Metal-ferroelectric-insulator-semiconductor (MFIS) capacitors with 390-nm-thick SrBi/sub 2/Ta/sub 2/O/sub 9/ (SBT) ferroelectric film and 8-nm-thick hafnium oxide (HfO/sub 2/) layer on silicon substrate have been fabricated and characterized. It is demonstrated for the first time that the MFIS stack exhibits a large memory window of around 1.08 V at an operation voltage of 3.5 V. Moreover, the MFIS memory structure suffers only 18% degradation in the memory window after 10/sup 9/ switching cycles. The excellent performance is attributed to the formation of well-crystallized SBT perovskite thin film on top of the HfO/sub 2/ buffer layer, as evidenced by the distinctive sharp peaks in X-ray diffraction (XRD) spectra. In addition to its relatively high /spl kappa/ value, HfO/sub 2/ also serves as a good seed layer for SBT crystallization, making the proposed Pt/SrBi/sub 2/Ta/sub 2/O/sub 9//HfO/sub 2//Si structure ideally suitable for low-voltage and high-performance ferroelectric memories.