基于C8051F020和Atmega16的无线温度测量系统设计

提出了基于片上系统C8051F020和AVR单片机Atmega16无线温度测量系统的研发方案,同时结合C8051F020和Atmega16两个微处理器,给出了CPU结构和独立的温度补偿方案,同时介绍了无线测温系统的主要特点和硬件系统各模块的功能和特点,并对主控制模块和无线发射模块的软件设计进行了论述。实际测试表明．本设计可以使温度测量的速度和精度有效提高,同时可提升系统的稳定性。     

单片机液晶显示系统的设计

以C8051F单片机和液晶显示控制器KS0108为核心,设计了单片机控制的液晶显示系统。重点研究了图形的动态显示技术,介绍了液晶显示模块的硬件、软件特性。文中设计的电路在C8051F020单片机仿真实验系统上进行了仿真,实验结果表明,设计达到了预期目标。     

基于C8051F020的船载卫星电视接收系统

船载卫星电视接收天线为三轴捷联式陀螺稳定系统,该系统可以隔离船体的运动,实现天线相对于大地的稳定性并能跟踪卫星.C8051F020单片机是美国Cygnal公司推出的完全集成的混合信号SoC(片上系统).文中介绍了以C8051F020单片机为核心的船载卫星电视接收系统的设计方案,并给出了硬件和软件的实现方法.     

基于USB20C模块的单片机系统与PC机的通信

为了解决单片机系统与PC机间通过RS-232C接口传输数据速度慢的问题,提出了采用专用USB模块-USB20C来设计USB接口电路的方法。通过USB20C与高性能单片机C8051F020的硬件连接。实现了数控切割系统中C8051F020与PC机的高速数据通信,并给出了C8051F020端软件的具体实现。该方法避免了开发USB接口驱动程序,传输速率快,可靠性高,很好地满足了数控系统的实时性要求。对采用USB接口传输数据的应用系统设计有一定的参考价值。     

利用C8051F020系列单片机实现智能仪器开发

简单介绍C8051F020系列混合信号单片机,简述利用该单片机进行智能仪器开发的基本方法.并在此基础上简要介绍一种利用C8051F020单片机实现的基于Ka、Ku、X三个波段的简易一次雷达系统构成的用于测量特定物质燃烧火焰特性的微波测量系统,及简述该系统的组成、工作原理以及实现方法.     

基于C8051F020单片机的多路压力测量仪

介绍了一种基于C8051F020单片机的多路压力测量仪.该测量仪选用电阻应变式压力传感器采集压力信号,并经放大电路处理后送入C8051F020单片机,再由C8051F020单片机内部的A/D转换器将采集到的压力信号进行模数转化,然后分别对数据进行存储和显示.该测量仪能测量6路压力信号,并且各测量点都能单独检测和设置.由于采用了C8051F020单片机,简化了硬件电路,增强了抗干扰能力,使得测量仪具有测量精度高,冲击小等特点.     

用C8051F020主控的液晶显示模块FM12232C及其应用

介绍了C8051F020单片机和图形点阵液晶显示模块FM12232C的性能特点，分析了在单片机C8051F020主控下FM12232C的硬件接口电路和软件设计方法，利用该方法可成功实现对液晶模块的控制和汉字显示。     

C8051F020单片机在磁致伸缩位移传感器中的应用

介绍了一种基于C8051F020单片机的数据采集系统,叙述了磁致伸缩线性位移传感器的工作原理、C8051F020单片机性能等,通过C8051F020单片机组成的硬件电路对磁致位移传感器数据进行采集,将采集到的位移数据进行滤波、放大、转换并在液晶显示器上显示出来。     

C8051F020单片机及其在总磷在线自动分析仪中的应用

C8051F020是Cygnal公司生产的混合信号系统级单片机 ,片内集成了CIP-51的CPU内核 ,且指令系统与MCS-51完全兼容。文章介绍了C8051F020的性能特点 ,给出了基于C8051F020单片机的总磷在线自动分析仪的设计构成及应用程序流程。     

基于C8051F020单片机的电机变频遥控控制系统

本文介绍了以C8051F020单片机为核心的遥控控制系统,该系统主要由遥控发射器和C8051F020单片机控制的接收电路以及输入检测、输出控制电路组成。系统结构灵活、成本低,易于扩充和修改。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.