Effect of different reductants for palladium loading on hydrogen storage capacity of double-walled carbon nanotubes

The effects of different reductants for palladium loading on the hydrogen sorption characteristics of double-walled carbon nanotubes (DWCNTs) have been investigated. Pd nanoparticles were loaded on DWCNT surfaces for dissociation of H₂ into atomic hydrogen, which spills over to the defect sites on the DWCNTs. When we use different reductants, the reduction capabilities and other effects of the different reductants are different, which affects the hydrogen storage capacity of the DWCNTs. In this work, the amount of hydrogen storage capacity was determined (by AMC Gas Reactor Controller) to be 1.7, 2.0, 2.55, and 3.0 wt% for pristine DWCNTS and for 2.0%Pd/DWCNTs using H₂, l-ascorbic acid, and NaBH₄ as reductants, respectively. We found that the hydrogen storage capacity can be enhanced by loading with 2% Pd nanoparticles and selecting a suitable reductant. Furthermore, the sorption can be attributed to the chemical reaction between atomic hydrogen and the dangling bonds of the DWCNTs.     

Chemical processing of double-walled carbon nanotubes for enhanced hydrogen storage

Double-walled carbon nanotubes (DWCNTs) were modified for enhanced hydrogen storage by employing a combination of two techniques: KOH activation for the formation of defects on DWCNT surfaces and loading of the DWCNTs with nanocrystalline Pd. The physical properties of the pristine DWCNTs and chemically modified DWCNTs were systematically characterised by X-ray diffraction, transmission electron microscopy, Raman spectroscopy and Brunauer–Emmett–Teller (BET) surface area measurements. The amounts of hydrogen storage capacity were measured at ambient temperature and found to be 1.7, 2.0, 3.7, and 2.8 wt% for pristine DWCNTS, 2 wt% Pd DWCNTs, activated DWCNTs, and 2 wt% Pd activated DWCNTs, respectively. Hydrogen molecules could be adsorbed on defect sites created by chemical activation in DWCNTs through van der Waals forces. For Pd nanoparticle loaded DWCNTs, H₂ molecules could be dissociated into atomic hydrogen and adsorbed on defect sites. We found that the hydrogen storage capacity of DWCNTs can be significantly enhanced by chemical activation or loading with Pd nanoparticles.     

In situ deposition of Pd nanoparticles with controllable diameters in hollow carbon spheres for hydrogen storage

A novel in situ synthesis of Pd nanoparticles supported in hollow carbon spheres (HCS) is reported. The size of the nanoparticles can be tuned via application of different Pd precursors. The hydrogen storage properties of Pd supported in HCS under room temperature were examined at partial pressures. We observed significant difference between the storage capacities of two samples containing Pd nanoparticles with different diameter distributions. The results showed that the sample with suitable diameters of Pd nanoparticles was more favorable for the H₂ storage, even lower mass of Pd was used. The maximum hydrogen storage of 0.36 wt % exhibited the sample with Pd nanoparticles with the diameter of 11 nm (measured at 298 K and 24 bar) and it was enhanced by the factor of two in respect to the pristine HCS. The enhanced storage capacity is due to cumulative hydrogen adsorption by HCS and Pd nanoparticles. We also propose the mechanism of hydrogen storage in our material.     

Activated carbons doped with Pd nanoparticles for hydrogen storage

Three activated carbons (ACs) having apparent surface areas ranging from 2450 to 3200 m²/g were doped with Pd nanoparticles at different levels within the range 1.3–10.0 wt.%. Excess hydrogen storage capacities were measured at 77 and 298 K at pressures up to 8 MPa. We show that hydrogen storage at 298 K depends on Pd content at pressures up to 2–3 MPa, below which the stored amount is low (<0.2 wt.%). At higher pressures, the micropore volume controls H₂ storage capacity. At 77 K, Pd doping has a negative effect on hydrogen storage whatever the pressure considered. From N₂ adsorption at 77 K, TPR, XRD, TEM, and H₂ chemisorption studies, we concluded that: (i) Pd particles remained mainly decorating the outer surface of the ACs; (ii) increasing Pd content produced an increase of the metal particle size; (iii) ACs with higher surface area produced smaller metallic nanoparticles at a given Pd content.     

Hydrogen storage in hybrid nanostructured carbon/palladium materials: Influence of particle size and surface chemistry

Hydrogen adsorption on porous materials is one of the possible methods proposed for hydrogen storage for transport applications. One way for increasing adsorption at room temperature is the inclusion of metal nanoparticles to increase hydrogen–surface interactions. In this study, ordered mesoporous carbon materials were synthesized by replication of nanostructured mesoporous SBA-15 silica. The combination of different carbon precursors allowed to tailor the textural, structural and chemical properties of the materials. These carbons were used for the synthesis of hybrid nanostructured carbon/palladium materials with different sizes of metal nanoparticles. The hydrogen sorption isotherms were measured at 77 K and 298 K between 0.1 and 8 MPa. Hydrogen storage capacities strongly correlate with the textural properties of the carbon at 77 K. At room temperature, Pd nanoparticles enhance hydrogen storage capacity by reversible formation of hydride PdH_x and through the spillover mechanism. The hydrogen uptake depends on the combined influences of metal particle size and of carbon chemical properties. Carbons obtained from sucrose precursors lead to the hybrid materials with the highest storage capacities since they exhibits a large microporous volume and a high density of oxygenated surface groups.     

Hydrogen sorption properties of Pd-doped carbon molecular sieves

Decoration with transition metal catalysts has been reported to enhance H₂ storage capacity of carbon materials at ambient temperature. Furthermore, it has been proposed that surface oxygen groups may improve the process. In this study, a carbon molecular sieve was subjected to controlled oxidation and consequent doping with Pd nanoparticles. The H₂ sorption performance of the pristine and oxidized, undoped and doped materials was examined at 298 K up to 20 bar. It was found that the non-oxidized carbon-Pd composite did not show any spillover based sorption increase. On the other hand the oxidized samples reveal a slight enhancement that could be attributed to a weak chemisorption process initiated by the so-called ‘‘spillover’’ effect. Overall, the contribution of spillover to the total hydrogen storage capacity of this system (under the conditions studied) was not found to be of great significance.     

Enhancement of H2 uptake due to morphological modulation in vanadium pentoxide foam

The high pressure H₂ sorption isotherms for vanadium pentoxide foam (VOF) were obtained at a liquid nitrogen temperature. The enhancement of hydrogen storage capacity occurred in as-prepared VOF (∼1.0 wt%) in contrast to that in pristine vanadium pentoxide (∼0.2 wt%). The maximum capacity of hydrogen storage (∼2.0 wt%) was achieved by thermal annealing at T_a = 623 K. The enhancement of hydrogen storage in VOF is attributed to the morphological modulation by thermal annealing.     

Hydrogen sorption in transition metal modified mesoporous materials

Ni, Rh and Pd incorporated mesoporous MCM-41, MCM-48, HMS and SBA-15 samples were synthesized and were characterized using XRD, ICP/EDX and N₂ adsorption–desorption at 77.4 K. The hydrogen adsorption studies in the synthesized materials were performed at 77.4 K (up to 112 kPa) and 303 K (up to 4000 kPa). The hydrogen adsorption isotherms of pristine and transition metals incorporated mesoporous materials at 77.4 K were completely reversible reflecting physisorption of hydrogen in these materials. The hydrogen adsorption isotherms at 303 K were not reversible showing the chemisorption of hydrogen in these materials at 303 K. Hydrogen sorption studies showed that transition metal modification improved the hydrogen storage capacity of mesoporous materials at 303 K. The desorption of the adsorbed hydrogen by heating up to 500 K from the mesoporous materials were also carried out for studying the recovery of adsorbed hydrogen from transition metal incorporated mesoporous materials.     

Enhancement of hydrogen storage capacity in polyaniline-vanadium pentoxide nanocomposites

The high-pressure H₂ sorption isotherms of polyaniline–vanadium pentoxide nanocomposites (PANI–VONC) have been performed at liquid nitrogen temperature. A large increment of hydrogen storage capacity occurs in PANI–VONC (∼1.8 wt%) in contrast to that in pristine vanadium pentoxide (∼0.2 wt%) and in non-treated polyaniline (∼0.2 wt%). It is considered that the reason for the enhancement of hydrogen storage in PANI–VONC is the intercalation of polyaniline (PANI) into the vanadium pentoxide layers. The intercalation of PANI decreases the interlayer distance from 1.1 nm between vanadium pentoxide layers to 0.72 nm between vanadium pentoxide layer and polyaniline layer.     

Improved hydrogen storage properties of Mg-based nanocomposite by addition of LaNi5 nanoparticles

Mg (200 nm) and LaNi₅ (25 nm) nanoparticles were produced by the hydrogen plasma-metal reaction (HPMR) method, respectively. Mg–5 wt.% LaNi₅ nanocomposite was prepared by mixing these nanoparticles ultrasonically. During the hydrogenation/dehydrogenation cycle, Mg–LaNi₅ transformed into Mg–Mg₂Ni–LaH₃ nanocomposite. Mg particles broke into smaller particles of about 80 nm due to the formation of Mg₂Ni. The nanocomposite showed superior hydrogen sorption kinetics. It could absorb 3.5 wt.% H₂ in less than 5 min at 473 K, and the storage capacity was as high as 6.7 wt.% at 673 K. The nanocomposite could release 5.8 wt.% H₂ in less than 10 min at 623 K and 3.0 wt.% H₂ in 16 min at 573 K. The apparent activation energy for hydrogenation was calculated to be 26.3 kJ mol⁻¹. The high sorption kinetics was explained by the nanostructure, catalysis of Mg₂Ni and LaH₃ nanoparticles, and the size reduction effect of Mg₂Ni formation.     

Magnesium and iron loaded hollow glass microspheres (HGMs) for hydrogen storage

The development of a safe and efficient method for hydrogen storage is essential for the use of hydrogen with fuel cells for vehicular applications. Hollow glass microspheres (HGMs) have characteristics suitable for hydrogen storage and are expected to be a potential hydrogen carrier to be used for energy release applications. The HGMs with 10–100 μm diameters, 100–1000 Å pore width and 3–8 μm wall thicknesses are expected to be useful for hydrogen storage. In our research we have prepared HGMs from amber glass powder of particle size 63–75 μm using flame spheroidisation method. The HGMs samples with magnesium and iron loading were also prepared to improve the heat transfer property and thereby increase the hydrogen storage capacity of the product. The feed glass powder was impregnated with calculated amount of magnesium nitrate hexahydrate salt solution to get 0.2–3.0 wt% Mg loading on HGMs. Required amount of ferrous chloride tetrahydrate solution was mixed thoroughly with the glass feed powder to prepare 0.2–2 wt% Fe loaded HGMs. Characterizations of all the HGMs samples were done using FEG-SEM, ESEM and FTIR techniques. Adsorption of hydrogen on all the Fe and Mg loaded HGMs at 10 bar pressure was conducted at room temperature and at 200 °C, for 5 h. The hydrogen adsorption capacity of Fe loaded sample was about 0.56 and 0.21 weight percent for Fe loading 0.5 and 2.0 weight percentage respectively. The magnesium loaded samples showed an increase of hydrogen adsorption from 1.23 to 2.0 weight percentage when the magnesium loading percentage was increased from 0 to 2.0. When the magnesium loading on HGMs was increased beyond 2%, formation of nano-crystals of MgO and Mg was seen on the HGMs leading to pore closure and thereby reduction in hydrogen storage capacity.     

Improved hydrogen storage performance of defected carbon nanotubes with Pd spillover catalysts dispersed using supercritical CO2 fluid

Hydrogen storage properties of carbon nanotubes (CNTs) modified by oxidative etching and decoration of Pd spillover catalysts are investigated. A mixed H₂SO₄/H₂O₂ solution containing ferrous ions (Fe²⁺) is useful to open the caps, to shorten the length, and to generate defects on CNTs. The Pd catalysts are deposited on the CNTs with the aid of supercritical carbon dioxide (scCO₂); as a result, a highly dispersed Pd nanoparticles and an intimate connection between Pd and carbon surface can be obtained. Combination of the two approaches can optimize a hydrogen spillover reaction on CNTs, resulting in a superior hydrogen storage capacity of 1.54 wt% (at 25 °C and 6.89 MPa), which corresponds to an enhancement factor of ∼4.5 as compared to that of pristine CNTs.     

Electrochemical hydrogen storage behavior of single-walled carbon nanotubes (SWCNTs) coated with Ni nanoparticles

The electrochemical hydrogen storage properties of Ni nanoparticle coated SWCNT electrodes were investigated. A surface modification technique enabled different amounts of Ni nanoparticles to be deposited on the SWCNT surface, which was first chemically oxidized by 6 N HNO₃. The characteristic properties of the SWCNT samples coated with 4–12 wt.%Ni nanoparticles were examined using a scanning electron microscope with energy dispersive spectroscopy (SEM/EDX); micro-Raman spectroscopy; thermal analysis techniques consisting of both thermogravimetric analysis (TGA) and differential thermal analysis (DTA), and Brunauer–Emmett–Teller (BET) measurements. It was found that all of the SWCNT samples coated with 4–12 wt.%Ni nanoparticles possessed a similar pore-size distribution. According to the electrochemical test results, the highest electrochemical discharge capacity of 1404 mA h g⁻¹ was obtained for the SWCNT electrode coated with 8 wt.%Ni nanoparticles, which corresponded to 5.27 wt.% hydrogen storage. This enhancement of electrochemical hydrogen storage capacity was ascribed to the fact that the Ni nanoparticles act as a redox site, thus leading to an improved electrochemical hydrogen storage capacity. The results indicated that the SWCNT coated with Ni nanoparticles are a potential material for hydrogen storage.     

Ultra-fast response and highly selectivity hydrogen gas sensor based on Pd/SnO2 nanoparticles

It is still a challenging task to achieve the rapid detection of hydrogen (H₂) with the rapid development of hydrogen energy sector. In this work, the H₂ sensing capabilities of pristine and Pd-modified SnO₂ nanoparticles with the size of ～7 nm were systematically evaluated. The SnO₂ nanoparticles were synthesized via hydrothermal method and Pd modification was performed using impregnation route. Pd modification remarkably upgraded the H₂ sensing performances compared with the pristine SnO₂ gas sensor. The working temperature of SnO₂ decreased from 300 °C to 125 °C after Pd loading. Among the prepared Pd/SnO₂ gas sensors, 0.50 at.% Pd/SnO₂ sensor exhibited the highest response magnitude of 254 toward 500 ppm H₂ and rapid response/recovery time of 1/22 s at 125 °C. The enhanced H₂ sensing capabilities by Pd modification may be related to the catalytic effect and the resistance modulation.     

Effect of multi-wall carbon nanotubes supported palladium addition on hydrogen storage properties of magnesium hydride

To improve the hydrogen storage performance of magnesium hydride, multi-wall carbon nanotubes supported palladium (Pd/MWCNTs) was introduced to the magnesium-based materials. Pd/MWCNTs catalysts with different amounts of Pd (20 wt.%, 40 wt.%, 60 wt.%, 80 wt.%) were synthesized by a solution chemical reduction method. Afterwards, Mg₉₅–Pd_m/MWCNTs_5−m (m = 0, 1, 2, 3, 4, 5) were prepared for the first time by hydriding combustion synthesis (HCS) and mechanical milling (MM). It is determined by X-ray diffraction (XRD) analysis that Pd/MWCNTs can significantly increase the hydrogenation degree of magnesium during the HCS process. The microstructures of the composites obtained by transmission electron microscope (TEM) and field emission scanning electronic microscopy (FESEM) analyses show that Pd nanoparticles are well supported on the surface of carbon nanotubes and the Pd/MWCNTs are dispersed uniformly on the surface of MgH₂ particles. Moreover, it is revealed that there is a synergistic effect of MWCNTs and Pd on the hydrogen storage properties of the composites. The Mg₉₅–Pd₃/MWCNTs₂ shows the optimal hydriding/dehydriding properties, requiring only 100 s to reach its saturated hydrogen absorption capacity of 6.67 wt.% at 473 K, and desorbing 6.66 wt.% hydrogen within 1200 s at 573 K. Additionally, the dehydrogenation activation energy of MgH₂ in this system is decreased to 78.6 kJ/mol H₂, much lower than that of as-received MgH₂.     

Functionalization of TiO2 nanotubes with palladium nanoparticles for hydrogen sorption and storage

The use of hydrogen as an energy carrier is an attractive solution toward addressing global energy issues and reducing the effects of climate change. Design of new materials with high hydrogen sorption capacity and high stability is critical for hydrogen purification and storage. In this study, titanium dioxide nanotubes (TiO₂NTs) were modified with palladium nanoparticles (PdNPs) utilizing a facile photo-assisted chemical deposition approach. Electrochemical anodization was employed for the direct growth of TiO₂NTs. The PdNP functionalized TiO₂NTs (TiO₂NT/Pd) were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The hydrogen sorption behaviours and stability of the TiO₂NT/Pd nanocomposites were investigated and compared with nanoporous Pd networks that were deposited on a bulk titanium substrate (Ti/Pd) using cyclic voltammetry (CV) and chronoamperometry (CA). Our studies show that the TiO₂NT/Pd nanocomposites possess a much higher hydrogen storage capacity, faster kinetics for hydrogen sorption and desorption, and higher stability than the nanoporous Pd.     

Helical confinement effects on hydrogen storage in double-walled carbon nanotubes

Molecular configurations are some of the important factors that strongly affect the hydrogen adsorption in carbon nanotubes (CNTs). A Quantum Molecular dynamics simulations are performed to study the adsorption isotherm of torsional double-walled carbon nanotubes (DWCNTs) filled with hydrogen molecules. The considered key factors that affect the hydrogen storage responses of the DWCNTs are the adsorption energy and the surface tension effect. Our simulated results show that 2-sided effect is observed and kinetic diameter of H₂ molecules is shortened approximately 4.11% under helical confinement. The results further reveal that the amounts of hydrogen storage wt% are computed at 77 K and found to be 1.77 wt% and 3.92 wt% for pristine and twisted-DWCNTs, respectively. Finally, it is shown that the adsorption heat, which reflects surface property, is twisted dependent.     

The decoration of TiO2/reduced graphene oxide by Pd and Pt nanoparticles for hydrogen gas sensing

Reduced graphene oxide (RGO) was used to improve the hydrogen sensing properties of Pd and Pt-decorated TiO₂ nanoparticles by facile production routes. The TiO₂ nanoparticles were synthesized by sol–gel method and coupled on GO sheets via a photoreduction process. The Pd or Pt nanoparticles were decorated on the TiO₂/RGO hybrid structures by chemical reduction. X-ray photoelectron spectroscopy demonstrated that GO reduction is done by the TiO₂ nanoparticles and Ti–C bonds are formed between the TiO₂ and the RGO sheets as well. Gas sensing was studied with different concentrations of hydrogen ranging from 100 to 10,000 ppm at various temperatures. High sensitivity (92%) and fast response time (less than 20 s) at 500 ppm of hydrogen were observed for the sample with low concentration of Pd (2 wt.%) decorated on the TiO₂/RGO sample at a relatively low temperature (180 °C). The RGO sheets, by playing scaffold role in these hybrid structures, provide new pathways for gas diffusion and preferential channels for electrical current. Based on the proposed mechanisms, Pd/TiO₂/RGO sample indicated better sensing performance compared to the Pt/TiO₂/RGO. Greater rate of spill-over effect and dissociation of hydrogen molecules on Pd are considered as possible causes of the enhanced sensitivity in Pd/TiO₂/RGO.     

Catalytic effect of carbon nanostructures on the hydrogen storage properties of MgH2–NaAlH4 composite

The present investigation describes the hydrogen storage properties of 2:1 molar ratio of MgH₂–NaAlH₄ composite. De/rehydrogenation study reveals that MgH₂–NaAlH₄ composite offers beneficial hydrogen storage characteristics as compared to pristine NaAlH₄ and MgH₂. To investigate the effect of carbon nanostructures (CNS) on the de/rehydrogenation behavior of MgH₂–NaAlH₄ composite, we have employed 2 wt.% CNS namely, single wall carbon nanotubes (SWCNT) and graphene nano sheets (GNS). It is found that the hydrogen storage behavior of composite gets improved by the addition of 2 wt.% CNS. In particular, catalytic effect of GNS + SWCNT improves the hydrogen storage behavior and cyclability of the composite. De/rehydrogenation experiments performed up to six cycles show loss of 1.50 wt.% and 0.84 wt.% hydrogen capacity in MgH₂–NaAlH₄ catalyzed with 2 wt.% SWCNT and 2 wt.% GNS respectively. On the other hand, the loss of hydrogen capacity after six rehydrogenation cycles in GNS + SWCNT (1.5 + 0.5) wt.% catalyzed MgH₂–NaAlH₄ is diminished to 0.45 wt.%.     

Hydrogen sorption studies of palladium decorated graphene nanoplatelets and carbon samples

With the increasing population of the world, the need for energy resources is increasing rapidly due to the development of the industry. 88% of the world's energy needs are met from fossil fuels. Since there is a decrease in fossil fuel reserves and the fact that these fuels cause environmental pollution, there is an increase in the number of studies aimed to develop alternative energy sources nowadays. Hydrogen is considered to be a very important alternative energy source due to its some specific properties such as being abundant in nature, high calorific value and producing only water as waste when burned. An important problem with the use of hydrogen as an energy source is its safe storage. Therefore, method development is extremely important for efficient and safe storage of hydrogen. Surface area, surface characteristics and pore size distribution are important parameters in determining the adsorption capacity, and it is needed to develop new adsorbents with optimum parameters providing high hydrogen adsorption capacity. Until recently, several porous adsorbents have been investigated extensively for hydrogen storage. In this study, it was aimed to develop and compare novel Pd/carbon, Pd/multiwalled carbon nanotube, and Pd/graphene composites for hydrogen sorption. All the palladium/carbon composites were characterized by t-plot, BJH desorption pore size distributions, N₂ adsorption/desorption isotherms, and SEM techniques. The maximum hydrogen storage of 2.25 wt.% at −196 °C was achieved for Pd/KAC composite sample. It has been observed that the spillover effect of palladium increases the hydrogen sorption capacity.