Effect of hydraulic retention time on biohydrogen production from palm oil mill effluent in anaerobic sequencing batch reactor

The feasibility of hydrogen generation from palm oil mill effluent (POME), a high strength wastewater with high solid content, was evaluated in an anaerobic sequencing batch reactor (ASBR) using enriched mixed microflora, under mesophilic digestion process at 37 °C. Four different hydraulic retention times (HRT), ranging from 96 h to 36 h at constant cycle length of 24 h and various organic loading rate (OLR) concentrations were tested to evaluate hydrogen productivity and operational stability of ASBR. The results showed higher system efficiency was achieved at HRT of 72 h with maximum hydrogen production rate of 6.7 LH₂/L/d and hydrogen yield of 0.34 LH₂/g COD_feeding, while in longer and shorter HRTs, hydrogen productivity decreased. Organic matter removal efficiency was affected by HRT; accordingly, total and soluble COD removal reached more than 37% and 50%, respectively. Solid retention time (SRT) of 4-19 days was achieved at these wide ranges of HRTs. Butyrate was found to be the dominant metabolite in all HRTs. Low concentration of volatile fatty acid (VFA) confirmed the state of stability and efficiency of sequential batch mode operation was achieved in ASBR. Results also suggest that ASBR has the potential to offer high digestion rate and good stability of operation for POME treatment.     

Effect of hydraulic retention time on the hydrogen production in a horizontal and vertical continuous stirred-tank reactor

Hydraulic retention time (HRT) is the main process parameter for biohydrogen production by anaerobic fermentation. This paper investigated the effect of the different HRT on the hydrogen production of the ethanol-type fermentation process in two kinds of CSTR reactors (horizontal continuous stirred-tank reactor and vertical continuous stirred-tank reactor) with molasses as a substrate. Two kinds of CSTR reactors operated with the organic loading rates (OLR) of 12kgCOD/m3•d under the initial HRT of the 8 h condition, and then OLR was adjusted as 6kgCOD/m3•d when the pH drops rapidly. The VCSTR and HCSTR have reached the stable ethanol-type fermentation process within 21 days and 24 days respectively. Among the five HRTs settled in the range of 2–8 h, the maximum hydrogen production rate of 3.7LH₂/Ld and 5.1LH₂/Ld were investigated respectively in the VCSTR and HCSTR. At that time the COD concentration and HRT were 8000 mg/L and 5 h for VCSTR, while 10000 mg/L and 4 h for HCSTR respectively.Through the analysis on the composition of the liquid fermentation product and biomass under the different HRT condition in the two kinds of CSTR, it can found that the ethanol-type fermentation process in the HCSTR is more stable than VCSTR due to enhancing biomass retention of HCSTR at the short HTR.     

Hydrogen and methane production in a bio-electrochemical system assisted anaerobic baffled reactor

In this study, a new process was proposed to enhance the stability and efficiency of an anaerobic baffled reactor (ABR). The process was examined in a four equal compartments ABR with total volume of 3.46 L. The first compartment was operated for fermentative hydrogen production and the last three compartments were used as continuous singer chamber microbial electrolysis cells (MECs) for methanogenesis. The system was operated at 35 ± 1 °C and hydraulic retention time (HRT) of 24 h with influent chemical oxygen demand (COD) concentration of 3500 mg/L–4000 mg/L. The results indicated that the proportion of hydrogen in the first compartment was 20.7% and proportions of methane in the last three compartments were 98.0%, 93.6% and 70.1%, respectively. A total of 98.0% of COD removal rate was achieved as well. Hence, this new system has following advantages: hydrogen production with cleaner effluent, high COD removal rate, and net methane production for practical use.     

Biohydrogen production in anaerobic fluidized bed reactors: Effect of support material and hydraulic retention time

This study evaluated two different support materials (polystyrene and expanded clay) for biohydrogen production in an anaerobic fluidized bed reactor (AFBR) treating synthetic wastewater containing glucose (4000 mg L⁻¹). The AFBRs contained either polystyrene (R1) or expanded clay (R2) as support materials were inoculated with thermally pre-treated anaerobic sludge and operated at a temperature of 30 °C and a pH of approximately 5.5. The AFBRs were operated with a range of hydraulic retention times (HRTs) between 1 and 8 h. For R1 with an HRT of 2 h, the maximum hydrogen yield (HY) was 1.90 mol H₂ mol⁻¹ glucose, with 0.805 mg of biomass (as total volatile solids, or TVS) attached to each g of polystyrene. For R2 operated at an HRT of 2 h, the maximum HY was 2.59 mol H₂ mol⁻¹ glucose, with 1.100 mg of attached biomass (as TVS) g⁻¹ expanded clay. The highest hydrogen production rates (HPR) were 0.95 and 1.21 L h⁻¹ L⁻¹ for R1 and R2, respectively, using an HRT of 1 h. The H₂ content increased from 16–47% for R1 and from 22–51% for R2. No methane was detected in the biogas produced throughout the period of AFBR operation. These results show that the values of HY, HPR, H₂ content, and g of attached biomass g⁻¹ support material were all higher for AFBRs containing expanded clay than for reactors containing polystyrene.     

Continuous biohydrogen production from liquid swine manure supplemented with glucose using an anaerobic sequencing batch reactor

Liquid swine manure supplemented with glucose (10 g/L) was used as substrate for hydrogen production using an anaerobic sequencing batch reactor at 37 ± 1 °C and pH 5.0 under different hydraulic retention times (HRTs). Decreasing HRT from 24 to 8 h caused an increasing hydrogen production rate from 0.05 to 0.15 L/h/L. Production rates of both total biogas and hydrogen were linearly correlated to HRT with R² being 0.993 and 0.997, respectively. The hydrogen yield ranged between 1.18 and 1.63 mol-H₂/mol glucose and the 12 h HRT was preferred for high production rate and efficient yield. For all the five HRTs examined, the glucose utilization efficiency was over 98%. The biogas mainly consisted of carbon dioxide and hydrogen (up to 43%) with no methane detected throughout the experiment. Ethanol and organic acids were the major aqueous metabolites produced during fermentation, with acetic acid accounting for 56–58%. The hydrogen yield was found to be related to the acetate/butyrate ratio.     

Biohydrogen from molasses with ethanol-type fermentation: Effect of hydraulic retention time

Though ethanol-type fermentation has many advantages for improving hydrogen production rate (HPR) in continuously mode hydrogen producing system, information on this fermentation is very deficient. The effect of hydraulic retention time (HRT) on biohydrogen production and operational stability of ethanol-type fermentation was investigated in a continuous stirred tank reactor (CSTR) using molasses as substrate. Five HRTs were examined, ranging from 4 to 10 h. At HRT 5 h, the highest HPR of 12.27 mmol L⁻¹ h⁻¹ was obtained from ethanol-type fermentation in the pH range of 4.3–4.4. During the whole operation process, ethanol, butyrate and acetate were the predominant metabolites. A total COD concentration of ethanol and acetate accounted for above 73.3% of total soluble microbial products. Linear regression showed that HPR and ethanol production rate were proportionately correlated at all HRTs which could be expressed as y = 0.9821x − 3.5151 (r² = 0.9498). It is meaningful that the proposed recovery of both hydrogen and ethanol from fermentation process can improve energy production rate and economic profit. Results demonstrated that the best energy production rate was 15.50 kJ L⁻¹ h⁻¹, occurred at HRT = 5 h.     

Biological hydrogen production from sweet sorghum syrup by mixed cultures using an anaerobic sequencing batch reactor (ASBR)

Continuous biological hydrogen production from sweet sorghum syrup by mixed cultures was investigated by using anaerobic sequencing batch reactor (ASBR). The ASBR was conducted based on the optimum condition obtained from batch experiment i.e. 25 g/L of total sugar concentration, 1.45 g/L of FeSO₄ and pH of 5.0. Feasibility of continuous hydrogen fermentation in ASBR operation at room temperature (30 ± 3 °C) with different hydraulic retention time (HRT) of 96, 48, 24 and 12 hr and cycle periods consisting of filling (20 min), settling (20 min), and decanting (20 min) phases was analyzed. Results showed that hydrogen content decreased with a reduction in HRT i.e. from 42.93% (96 hr HRT) to 21.06% (12 hr HRT). Decrease in HRT resulted in a decrease of solvents produced which was from 10.77 to 2.67 mg/L for acetone and 78.25 mg/L to zero for butanol at HRT of 96 hr-12 hr, respectively. HRT of 24 hr was the optimum condition for ASBR operation indicated by the maximum hydrogen yield of 0.68 mol H₂/mol hexose. The microbial determination in DGGE analysis indicated that the well-known hydrogen producers Clostridia species were dominant in the reacting step. The presence of Sporolactobacillus sp. which could excrete the bacteriocins causing the adverse effect on hydrogen-producing bacteria might responsible for the low hydrogen content obtained.     

Hydrogen production from alcohol distillery wastewater containing high potassium and sulfate using an anaerobic sequencing batch reactor

In this study, the feasibility of hydrogen production from alcohol distillery wastewater containing high potassium and sulfate was investigated using an anaerobic sequencing batch reactor (ASBR). The seed sludge taken from an anaerobic tank treating the distillery wastewater was boiled for 15 min before being fed to the ASBR. The ASBR system was operated under different feed chemical oxygen demand (COD) values and different COD loading rates at a mesophilic temperature of 37 °C, a controlled pH at 5.5, and a cycle time of 6 cycles per day. When the studied ASBR was operated under the best conditions (providing a maximum hydrogen production efficiency) of a feed COD of 40,000 mg/l, a COD loading rate of 60 kg/m³ d, and a hydraulic retention time of 16 h, the produced gas was found to contain 34.7% H₂ and 65.3% CO_2, without any methane being detected. Under these best conditions, the specific hydrogen production rate (SHPR) of 270 ml H₂/g MLVSS d (or 3310 ml H₂/l d), and hydrogen yield of 172 ml H₂/g COD removed, were obtained. When the feed COD exceeded 40,000 mg/l, the process performance in terms of hydrogen production decreased because of the potassium and sulfate toxicity.     

Effect of pre-treatment and hydraulic retention time on biohydrogen production from organic wastes

This study investigated the effect of pre-treatment and hydraulic retention time (HRT) on biohydrogen production from organic wastes. Various pre-treatments including thermal, base, acid, ultrasonication, and hydrogen peroxide were applied alone or in combination to enhance biohydrogen production from potato and bean wastewater in batch tests. All the pre-treated samples showed higher hydrogen production than the control tests. Hydrogen peroxide pre-treatment achieved the best results of 939.7 and 470 mL for potato and bean wastewater, respectively. Continuous biohydrogen production from sucrose, potato and bean wastewater was significantly influenced by reducing the HRT as 24, 18 and 12 h. Sucrose and potato showed similar behavior, where the hydrogen production rate (HPR) increased with decreasing the HRT. Optimum hydrogen yield results of 320 mL-H₂/g-VS (sucrose) and 150 mL-H₂/g-VS (potato) were achieved at HRT of 18 h. Bean wastewater showed optimum HPR of 0.65 L/L.d with hydrogen yield of 80 mL-H₂/g-VS at 24 h HRT.     

Hydrogen production from alcohol wastewater with added fermentation residue by an anaerobic sequencing batch reactor (ASBR) under thermophilic operation

The objective of this study was to investigate the enhancement of hydrogen production from alcohol wastewater by adding fermentation residue using an anaerobic sequencing batch reactor (ASBR) under thermophillic operation (55 °C) and at a constant pH of 5.5. The digestibility of the added fermentation residue was also evaluated. For a first set of previous experiments, the ASBR system was operated to obtain an optimum COD loading rate of 50.6 kg/m³ d of alcohol wastewater without added fermentation residue and the produced gas contained 31% H₂ and 69% CO₂. In this experiment, the effect of added fermentation residue (100–1200 mg/l) on hydrogen production performance was investigated under a COD loading rate of 50.6 kg/m³ d of the alcohol wastewater. At a fermentation residue concentration of 1000 mg/l, the produced gas contained 40% H₂ and 60% CO₂ without methane and the system gave the highest hydrogen yield and specific hydrogen production rate of 128 ml/g COD removed and 2880 ml/l d, respectively. Under thermophilic operation with a high total COD loading rate (51.8 kg/m³ d) and a short HRT (21 h) at pH 5.5, the ASBR system could only break down cellulose (41.6%) and hemicellulose (21.8%), not decompose lignin.     

An anaerobic sequential batch reactor for enhanced continuous hydrogen production from fungal pretreated cornstalk hydrolysate

Anaerobic sequencing batch reactor (ASBR) process offers great potential for H₂ production from wastewaters. In this study, an ASBR was used at first time for enhanced continuous H₂ production from fungal pretreated cornstalk hydrolysate by Thermoanaerobacterium thermosaccharolyticum W16. The reactor was operated at different hydraulic retention times (HRTs) of 6, 12, 18, and 24 h by keeping the influent hydrolysate constant at 65 mmol sugars L⁻¹. Results showed that increasing the HRT from 6 to 12 h led to the H₂ production rate increased from 6.7 to the maximum of 9.6 mmol H₂ L⁻¹ h⁻¹ and the substrate conversion reached 90.3%, although the H₂ yield remained at the same level of 1.7 mol H₂ mol⁻¹ substrate. Taking into account both H₂ production and substrate utilization efficiencies, the optimum HRT for continuous H₂ production via an ASBR was determined at 12 h. Compared with other continuous H₂ production processes, ASBR yield higher H₂ production at relatively lower HRT. ASBR is shown to be another promising process for continuous fermentative H₂ production from lignocellulosic biomass.     

Effect of hydraulic retention time on a continuous biohydrogen production in a packed bed biofilm reactor with recirculation flow of the liquid phase

The present paper reports on results obtained from experiments carried out in a laboratory-scale anaerobic packed bed biofilm reactor (APBR), with recirculation of the liquid phase, for continuously biohydrogen production via dark fermentation. The reactor was filled with Kaldnes^® biofilm carrier and inoculated with an anaerobic mesophilic sludge from a urban wastewater treatment plant (WWTP). The APBR was operated at a temperature of 37 °C, without pH buffering. The effect of theoretical hydraulic retention time (HRT) from 1 to 5 h on hydrogen yield (HY), hydrogen production rate (HPR), substrate conversion and metabolic pathways was investigated. This study indicates the possibility of enhancing hydrogen production by using APBR with recirculation flow. Among respondents values of HRT the highest average values of HY (2.35 mol H₂/mol substrate) and HPR (0.085 L h^?1L^?1) have been obtained at HRT equal to 2 h.     

Effect of hydraulic retention time on hydrogen production from sewage sludge and wine vinasse in a thermophilic acidogenic CSTR: A promising approach for hydrogen production within the biorefinery concept

The aim of the present study was to investigate the effect of hydraulic retention time (HRT) on hydrogen production from sewage sludge:wine vinasse (50:50 v/v) in a laboratory-scale continuously stirred tank reactor under thermophilic conditions. For this purpose, nine HRT ranging from 5.0 to 0.25 days were tested. Maximum hydrogen production and specific hydrogen production of 0.90 LH₂/L_reactor/d and 35.19 mLH₂/g VS_added were respectively obtained at a HRT of 0.5 days. Eubacteria was the main group (65–79%) for all the tested HRT. Decreasing HRT was inversely correlated with hydrogen production and microbial population. HRT of 0.5 days is optimal for the growth of the acidogenic population and therefore this population is more active and maximum microbial activity (15.28·10^?10 LH₂/cells) was also achieved at this HRT.     

Fermentative H2 production using a switchgrass steam exploded liquor fed to mixed anaerobic cultures: Effect of hydraulic retention time,linoleic acid and nitrogen sparging

Fermentative hydrogen (H₂) production from a steam exploded switchgrass liquor using inhibited mixed anaerobic microbial communities was studied in upflow anaerobic sludge blanket reactors (UASBRs). Increasing the H₂ yield was accomplished by treating the inoculum with linoleic acid (LA), varying the hydraulic retention time (HRT) and sparging liquid phase with nitrogen (N₂). A maximum H₂ yield of 2.56 ± 0.10 mol mol⁻¹ hexose, was obtained at a 6 h HRT in LA treated cultures sparged with N₂. Sparging or LA treatment alone was able to enhance the H₂ yield by 46 ± 5% and 38 ± 3%, respectively, in comparison to control cultures operating at a 6 h HRT. Of the different methods employed, N₂ sparging in combination with LA treatment proved to be more effective in enriching the H₂ producing bacteria belonging to Clostridium sp. Species belonging to Propionibacterium, Bacteroides and Eubacterium, which were associated with H₂ consumption and reduced byproducts formation, were observed in addition to Clostridium sp. in unsparged control cultures.     

Biohydrogen production,sludge granulation,and microbial community in an anaerobic inner cycle biohydrogen production (AICHP) reactor at different hydraulic retention times

This study investigated the continuous biohydrogen production in an anaerobic inner cycle biohydrogen production (AICHP) reactor fed with synthetic molasses wastewater as the model substrate under mesophilic conditions (37 ± 1 °C). The hydraulic retention times (HRTs) were set as 6.12, 4.90, 4.08, 3.50, and 3.06 h. Both maximum hydrogen production rate (HPR) (8.08 ± 0.48 L/L/d) and maximum granule formation were achieved at the HRT of 3.50 h. Acetic acid and butyric acid were the dominant metabolites in all tested HRTs throughout the experiment. Microbial community analysis showed that shortening the HRT promoted hydrogen production. This was mainly achieved by enhancing the growth of acetogenic bacteria in the AICHP reactor, rather than the growth of hydrogen-producing bacteria.     

Hydrogen production from alcohol wastewater by an anaerobic sequencing batch reactor under thermophilic operation: Nitrogen and phosphorous uptakes and transformation

The objective of this study was to investigate hydrogen production from alcohol wastewater using an anaerobic sequencing batch reactor (ASBR) under thermophilic operation and at a constant pH of 5.5. Under the optimum COD loading rate of 68 kg/m³d, the produced gas contained 43% H₂ without methane and the system provided a hydrogen yield and specific hydrogen production rate of 130 ml H₂/g COD removed and 2100 ml H₂/l d, respectively, which were much higher than those obtained under the mesophilic operation. Under thermophilic operation, both nitrogen and phosphate uptakes were minimal at the optimum COD loading rate for hydrogen production and most nitrogen uptake was derived from organic nitrogen. Under the thermophilic operation for hydrogen production, the nutrient requirement in terms of COD:N:P was found to be 100:6:0.5, which was much higher than that for the methenogenic step for methane production under both thermophilic and mesophilic operations and for the acidogenic step for hydrogen production under mesophilic operation.     

Biohydrogen production from purified terephthalic acid (PTA) processing wastewater by anaerobic fermentation using mixed microbial communities

Purified terephthalic acid (PTA) processing wastewater was evaluated as a fermentable substrate for hydrogen (H₂) production with simultaneous wastewater treatment by dark-fermentation process in a continuous stirred-tank reactor (CSTR) with selectively enriched acidogenic mixed consortia under continuous flow condition in this paper. The inoculated sludge used in the reactor was excess sludge taken from a second settling tank in a local wastewater treatment plant. Under the conditions of the inoculants not less than 6.3 gVSS/L, the organic loading rate (OLR) of 16 kgCOD/m³ d, hydraulic retention time (HRT) of 6 h and temperature of (35 ± 1) °C, when the pH value, alkalinity and oxidation–reduction potential (ORP) of the effluent ranged from 4.2 to 4.4, 280 to 350 mg CaCO₃/L, and −220 to −250 mV respectively, soluble metabolites were predominated by acetate and ethanol, with smaller quantities of propionate, butyrate and valerate. Stable ethanol-type fermentation was formed with the sum of ethanol and acetate concentration ratio of 70.31% to the total liquid products after 25 days operation. The H₂ volume content was estimated to be 48–53% of the total biogas and the biogas was free of methane throughout the study. The average biomass concentration was estimated to be 10.82 gVSS/L, which favored H₂ production efficiently. The rate of chemical oxygen demand (COD) removal reached at about 45% and a specific H₂ production rate achieved 0.073 L/gMLVSS d in the study. This CSTR system showed a promising high-efficient bioprocess for H₂ production from high-strength chemical wastewater.     

Enhancing biohydrogen production from chemical wastewater treatment in anaerobic sequencing batch biofilm reactor (AnSBBR) by bioaugmenting with selectively enriched kanamycin resistant anaerobic mixed consortia

The basic aim of this study was to investigate the feasibility of bioaugmentation strategy in the process of enhancing biohydrogen (H₂) production from chemical wastewater treatment (organic loading rate (OLR)—6.3 kg COD/m³-day) in anaerobic sequencing batch biofilm reactor (AnSBBR) operated at room temperature (28±2$28\pm 2$ °C) under acidophilic microenvironment (pH 6) with a total cycle period of 24 h. Parent augmented inoculum (kanamycin resistant) was acquired from an operating upflow anaerobic sludge blanket (UASB) reactor treating chemical wastewater and subjected to selective enrichment by applying repetitive/cyclic pre-treatment methods [altering between heat-shock treatment (100 °C; 2 h) and acid treatment (pH 3; 24 h)] to eliminate non-spore forming bacteria and to inhibit the growth of methanogenic bacteria (MB). Experimental data revealed the positive influence of bioaugmentation strategy on the overall H₂ production. Specific H₂ production almost doubled after augmentation from 0.297 to 0.483 mol H₂/kg COD_R-day. Chemical wastewater acted as primary carbon source in the metabolic reactions involving molecular H₂ generation leading to substrate degradation. The augmented culture persisted in the system till the termination of the experiments. The survival and retention of the augmented inoculum and its positive effect on process enhancement may be attributed to the adopted reactor configuration and operating conditions. Scanning electron microscope (SEM) images documented the selective enrichment of morphologically similar group of bacteria capable of producing H₂ under acidophilic conditions in anaerobic microenvironment. This depicted work corroborated successful application of bioaugmentation strategy to improve H₂ production rate from anaerobic chemical wastewater treatment.     

Effect of pH and sulfate concentration on hydrogen production using anaerobic mixed microflora

The effects of varying sulfate concentrations with pH on continuous fermentative hydrogen production were studied using anaerobic mixed cultures growing on a glucose substrate in a chemostat reactor. The maximum hydrogen production rate was 2.8 L/day at pH 5.5 and sulfate concentration of 3000 mg/L. Hydrogen production and residual sulfate level decreased with increasing the pH from 5.5 to 6.2. The volatile fatty acids (VFAs) and ethanol fractions in the effluent were in the order of butyric acid (HBu) > acetic acid (HAc) > ethanol > propionic acid (HPr). Fluorescence In Situ Hybridization (FISH) analysis revealed the presence of hydrogen producing bacteria (HPB) under all pH ranges while sulfate reducing bacteria (SRB) were present at pH 5.8 and 6.2. The inhibition in hydrogen production by SRB at pH 6.2 diminished entirely by lowering to pH 5.5, at which activity of SRB is substantially suppressed.