CO2 methanation combined with NH3 decomposition by in situ H2 separation using a Pd membrane reactor

Combination of the reactions by means of membrane separation techniques are of interest. The CO₂ methanation was combined with NH₃ decomposition by in situ H₂ separation through a Pd membrane. The CO₂ methanation reaction in the permeate side was found to significantly enhance the H₂ removal rate of Pd membrane compared to the use of sweep gas. The reaction rate of CO₂ methanation was not influenced by H₂ supply through the Pd membrane in contrast to NH₃ decomposition in the retentate side. However, the CH₄ selectivity could be improved by using a membrane separation technique. This would be caused by the active dissociated H species which might immediately react with adsorbed CO species on the catalysts to CH₄ before those CO species desorbed. From the reactor configuration tests, the countercurrent mode showed higher H₂ removal rate in the combined reaction at 673 K compared to the cocurrent mode but the reaction rate in CO₂ methanation should be improved to maximize the perfomance of membrane reactor.     

An oxy-fuel mass-recirculating process for H2 production with CO2 capture by autothermal catalytic oxyforming of methane

A new oxy-fuel H₂ generation process with CO₂ avoidance is provided. The process utilizes mass recirculation of CO and H₂O to the oxyforming reactor. A comparison between non-recirculating and mass-recirculating oxyforming reactor operation is given. Main benefits of mass recirculation are emphasized. The oxyforming reactor is integrated with the H₂ and CO₂ separators, fuel cell and O₂ generator. In the process C/O is equal to 0.5 while C/H determines the temperature level in the reactor. The reaction system includes combustion, steam reforming and water–gas shift reactions. The oxyforming process is found to be mass transport controlled with O₂ as the limiting reactant. It is emphasized that under MR conditions the decomposition of H₂/CO₂ by water–gas shift reaction is suppressed by means of CO/H₂O-enrichment and hence MR conditions allow for higher temperatures beneficial to endothermic steam reforming reaction. Under MR conditions the thermodynamic equilibrium limits are overcome and all reactions are forced to proceed to the completion which enables 100% selectivities to H₂ and CO₂. The effects of operation parameters such as temperature, flow rate, pressure and composition are examined. The derived S-terms enable for the concise interpretation of the effect of pressure on the concentration gradients transverse to the flow. The consistent control algorithm of the oxyforming reactor is provided.     

Thermodynamic analysis of a membrane-assisted chemical looping reforming reactor concept for combined H2 production and CO2 capture

There is great consensus that hydrogen will become an important energy carrier in the future. Currently, hydrogen is mainly produced by steam reforming of natural gas/methane on large industrial scale or by electrolysis of water when high-purity hydrogen is needed for small-scale hydrogen plants. Although the conventional steam reforming process is currently the most economical process for hydrogen production, the global energy and carbon efficiency of this process is still relatively low and an improvement of the process is key for further implementation of hydrogen as a fuel source. Different approaches for more efficient hydrogen production with integrated CO₂ capture have been discussed in literature: Chemical Looping Combustion (CLC) or Chemical Looping Reforming (CLR) and membrane reactors have been proposed as more efficient alternative reactor concepts relative to the conventional steam reforming process. However, these systems still present some drawbacks. In the present work a novel hybrid reactor concept that combines the CLR technology with a membrane reactor system is presented, discussed and compared with several other novel technologies. Thermodynamic studies for the new reactor concept, referred to as Membrane-Assisted Chemical Looping Reforming (MA-CLR), have been carried out to determine the hydrogen recovery, methane conversion as well as global efficiency under different operating conditions, which is shown to compare quite favorably to other novel technologies for H₂ production with CO₂ capture.     

Role of CO2 in the CH4 oxidation and H2 formation during fuel-rich combustion in O2/CO2 environments

The effect of CO₂ reactivity on CH₄ oxidation and H₂ formation in fuel-rich O₂/CO₂ combustion where the concentrations of reactants were high was studied by a CH₄ flat flame experiment, detailed chemical analysis, and a pulverized coal combustion experiment. In the CH₄ flat flame experiment, the residual CH₄ and formed H₂ in fuel-rich O₂/CO₂ combustion were significantly lower than those formed in air combustion, whereas the amount of CO formed in fuel-rich O₂/CO₂ combustion was noticeably higher than that in air. In addition to this experiment, calculations were performed using CHEMKIN-PRO. They generally agreed with the experimental results and showed that CO₂ reactivity, mainly expressed by the reaction CO₂ + H → CO + OH (R1), caused the differences between air and O₂/CO₂ combustion under fuel-rich condition. R1 was able to advance without oxygen. And, OH radicals were more active than H radicals in the hydrocarbon oxidation in the specific temperature range. It was shown that the role of CO₂ was to advance CH₄ oxidation during fuel-rich O₂/CO₂ combustion. Under fuel-rich combustion, H₂ was mainly produced when the hydrocarbon reacted with H radicals. However, the hydrocarbon also reacted with the OH radicals, leading to H₂O production. In fact, these hydrocarbon reactions were competitive. With increasing H/OH ratio, H₂ formed more easily; however, CO₂ reactivity reduced the H/OH ratio by converting H to OH. Moreover, the OH radicals reacted with H₂, whereas the H radicals did not reduce H₂. It was shown that OH radicals formed by CO₂ reactivity were not suitable for H₂ formation. As for pulverized coal combustion, the tendencies of CH₄, CO, and H₂ formation in pulverized coal combustion were almost the same as those in the CH₄ flat flame.     

Hydrogen permeation properties of Pd-coated V89.8Cr10Y0.2 alloy membrane using WGS reaction gases

The influence of co-existing gases on the hydrogen permeation was studied through a Pd-coated V_89.8Cr₁₀Y_0.2 alloy membrane. Preliminary hydrogen permeation experiments have been confirmed that hydrogen flux was 6.26 ml/min/cm² for a Pd-coated V_89.8Cr₁₀Y_0.2 alloy membrane (thick: 0.5 mm) using pure hydrogen as feed gas. Also, the hydrogen permeation flux decreased with decrease of hydrogen partial pressure at constant pressure when H₂/CO₂ and H₂/CO₂/H₂S mixture applied as feed gas respectively and permeation fluxes were satisfied with Sievert's law in different feed conditions. It was found from XRD and SEM results after permeation test that the Pd-coated V_89.8Cr₁₀Y_0.2 alloy membrane had good stability and durability for various mixture feeding conditions.     

H2SO4 stability of PBI-blend membranes for SO2 electrolysis

For hydrogen to become a serious contender for replacing fossil fuels, the manufacturing thereof has to be further investigated. One such process, the membrane based Hybrid Sulfur (HyS) process, where hydrogen is produced from the electrolysis of SO₂, has received considerable interest recently. Since H₂SO₄ is formed during SO₂ electrolysis, H₂SO₄ stability is a prerequisite for any membrane to be used in this process. In this study, pure as well as blended polybenzimidazole (PBI), partially fluorinated poly(arylene ether) (sFS) and nonfluorinated poly(arylene ethersulfone) (sPSU) membranes were investigated in terms of their acid stability as a function of acid concentration. Membranes were characterized using weight change, TGA, GPC, SEM/EDX and IEC. While a general stability was observed at 30 and 60 wt% H₂SO₄, the blended sFS-PBI and sPSU-PBI showed the highest stability throughout. According to the VI curve obtained for the SO₂ electrolysis, the sPSU-PBI blend membrane performed slightly better than Nafion^®117.     

Coal gasification with in situ CO2 capture by the synthetic CaO sorbent in a 1 kWth dual fluidised-bed reactor

Coal gasification with in situ CO₂ capture is believed to be able to produce highly concentrated H₂ with little or no CO₂ compared with the conventional process. This has been demonstrated by other researchers working on a single fluidised bed by continuously feeding the CaO sorbent. This work presents the results of coal gasification with in situ CO₂ capture by a synthetic CaO sorbent in a 1 kW_th dual fluidised-bed reactor at atmospheric pressure, which has not been reported in the literature. The synthetic CaO sorbent is cyclically used by going through multiple carbonation/calcination cycles during coal gasification.     

Influence of coating conditions on the H2 separation performance from H2/CH4 gas mixtures by the PDMS/PEI composite membrane

In the present study, the composite polyetherimide (PEI) membrane coated with poly dimethyl siloxane (PDMS) was synthesized and optimum conditions of coating were obtained for separation of hydrogen from methane. Three coating techniques “pouring solution inclined by 45°”, “film casting” and “dip-coating” were used. The effect of sequential coating for different methods on permselectivity of the membranes was investigated. In addition, the influences of coating conditions including coating solution concentration, coating and curing temperatures were examined. The results showed that when the concentration of PDMS coating solution was increased; the permeance of H₂ was initially declined rapidly and was then gradually leveled off. The optimum concentration of coating solution was 15 wt.%. The examination of the curing and coating temperatures showed no significant effect on H₂ permeance and selectivity. In the “dip coating” method, two times coating showed superior permeance and selectivity and in “film casting”, the performance of triple coating was promising. Higher selectivities for the composite membrane prepared by “dip-coating” introduced this method as the best method. The sequential dip-coating with different PDMS concentrations was applied and the selectivity was enhanced significantly from 26 to 96 for pure gases and from 22 to 70 for the binary gas mixture. Finally, the influence of pressure on the separation performance of the fabricated membrane was investigated.     

Preparation and characterization of multi-walled carbon nanotube/PBNPI nanocomposite membrane for H2/CH4 separation

By combining organic polymers normally used to make membrane filters with inorganic substances, multi-walled carbon nanotube (MWCNTs), an extraordinary ability to separate H₂ from CH₄ was developed in this study. A series of MWCNTs/PBNPI nanocomposite membrane with a nominal MWCNTs content between 1 and 15 wt% were prepared by solution casting method, in which the very fine MWCNTs were embedded into glassy polymer membrane. Detailed characterizations, such as morphology, thermal stability and crystalline structure have been conducted to understand the structures, composition and properties of nanocomposite membranes. The results found that this new class of membrane had increased permeability and enhanced selectivity, and a useful ability to filter gases and organic vapours at the molecular level.     

Recent developments in membrane-based technologies for CO2 capture

Developing new methods and technologies that compete with conventional industrial processes for CO₂ capture and recovery is a hot topic in the current research. Conventional processes do not fit with the current approach of process intensification but take advantage due to their maturity and large-scale implementation. Acting in a precombusion scenario or post-combustion scenario involves the separation of CO₂/H₂ or CO₂/N₂, respectively.     

High capacity potassium-promoted hydrotalcite for CO2 capture in H2 production

This paper presents an experimental study for a newly modified K₂CO₃-promoted hydrotalcite material as a novel high capacity sorbent for in-situ CO₂ capture. The sorbent is employed in the sorption enhanced steam reforming process for an efficient H₂ production at low temperature (400–500 ^°C). A new set of adsorption data is reported for CO₂ adsorption over K-hydrotalcite at 400 °C. The equilibrium sorption data obtained from a column apparatus can be adequately described by a Freundlich isotherm. The sorbent shows fast adsorption rates and attains a relatively high sorption capacity of 0.95 mol/kg on the fresh sorbent. CO₂ desorption experiments are conducted to examine the effect of humidity content in the gas purge and the regeneration time on CO₂ desorption rates. A large portion of CO₂ is easily recovered in the first few minutes of a desorption cycle due to a fast desorption step, which is associated with a physi/chemisorption step on the monolayer surface of the fresh sorbent. The complete recovery of CO₂ was then achieved in a slower desorption step associated with a reversible chemisorption in a multi-layer surface of the sorbent. The sorbent shows a loss of 8% of its fresh capacity due to an irreversible chemisorption, however, it preserves a stable working capacity of about 0.89 mol/kg, suggesting a reversible chemisorption process. The sorbent also presents a good cyclic thermal stability in the temperature range of 400–500 °C.     

Catalytic CO2 reforming of CH4 over Cr-promoted Ni/char for H2 production

The objective of the study is to investigate the catalytic performance of Cr-promoted Ni/char in CO₂ reforming of CH₄ at 850 °C. The char obtained from the pyrolysis of a long-flame coal at 1000 °C was used as the support. The catalysts were prepared by incipient wetness impregnation methods with different metal precursor doping sequence. The characterization of the composite catalysts was evaluated by XRD, XPS, SEM-EDS, TEM, H₂-TPR, CO₂-TPD, CH₄-TPSR, and CO₂-TPO. The results indicate that the catalyst prepared by co-impregnation of Ni and Cr possess higher activity than those by sequential impregnation. The optimal loading of Cr on 5 wt% Ni/char is 7.8 wt‰. Moreover, the molar feed ratio of CH₄/CO₂ has a considerable effect on both the stability and the activity of Cr–Ni/char. The main effect of Cr is the great enhance of the adsorption to CO₂. It is interesting that the conversions of CH₄ and CO₂ over Cr-promoted Ni/char and Ni/char decrease initially, following by a steady rise as the reaction proceeds with time-on-stream (TOS). In addition, cyclic tests were conducted and no distinct deterioration in the catalytic performance of the catalysts was observed. On the basis of the obtained results, nickel carbide was speculated to be the active species which was formed during the CO₂ reforming of CH₄ reaction.     

Effect of dry/wet-phase inversion method on fabricating polyetherimide-derived CMS membrane for H2/N2 separation

The research investigated carbon molecular sieve (CMS) membranes through the dry/wet-phase inversion method from the casting polyetherimide (PEI) on alumina support for hydrogen separation. Different coating techniques such as dry method (slide casting followed by drying under vacuum; and spin coating followed by drying under vacuum); and wet method (spin coating and then later kept in an isopropyl alcohol (IPA)/water coagulating bath) at different pyrolysis temperatures of 550, 600, 650 °C min⁻¹ were also investigated.     

Sorbent enhanced hydrogen production from steam gasification of coal integrated with CO2 capture

In this work, CO₂ capture and H₂ production during the steam gasification of coal integrated with CO₂ capture sorbent were investigated using a horizontal fixed bed reactor at atmospheric pressure. Four different temperatures (650, 675, 700, and 750 °C) and three sorbent-to-carbon ratios ([Ca]/[C] = 0, 1, 2) were studied. In the absence of sorbent, the maximum molar fraction of H₂ (64.6%) and conversion of coal (71.3%) were exhibited at the highest temperature (750 °C). The experimental results verified that the presence of sorbent in the steam gasification of coal enhanced the molar fraction of H₂ to more than 80%, with almost all CO₂ was fixed into the sorbent structure, and carbon monoxide (CO) was converted to H₂ and CO₂ through the water gas shift reaction. The steam gasification of coal integrated with CO₂ capture largely depended on the reaction temperature and exhibited optimal conditions at 675 °C. The maximum molar fraction of H₂ (81.7%) and minimum CO₂ concentration (almost 0%) were obtained at 675 °C and a sorbent-to-carbon ratio of 2.     

Ultrasonic spray pyrolysis synthesis of Ag/TiO2 nanocomposite photocatalysts for simultaneous H2 production and CO2 reduction

Simultaneous photocatalytic hydrogen production and CO₂ reduction (to form CO and CH₄) from water using methanol as a hole scavenger were investigated using silver-modified TiO₂ (Ag/TiO₂) nanocomposite catalysts. A simple ultrasonic spray pyrolysis (SP) method was used to prepare mesoporous Ag/TiO₂ composite particles using TiO₂ (P25) and AgNO₃ as the precursors. The material properties and photocatalytic activities were compared with those prepared by a conventional wet-impregnation (WI) method. It was found that the samples prepared by the SP method had a larger specific surface area and a better dispersion of Ag nanoparticles on TiO₂ than those prepared by the WI method, and as a result, the SP samples showed much higher photocatalytic activities toward H₂ production and CO₂ reduction. The optimal Ag concentration on TiO₂ was found to be 2 wt%. The H₂ production rate of the 2% Ag/TiO₂–SP sample exhibited a six-fold enhancement compared with the 2% Ag/TiO₂–WI sample and a sixty-fold enhancement compared with bare TiO₂. The molar ratio of H₂ and CO in the final products can be tuned in the range from 2 to 10 by varying the reaction gas composition, suggesting a viable way of producing syngas (a mixture of H₂ and CO) from CO₂ and water using the prepared Ag/TiO₂ catalysts with energy input from the sun.     

An experimental investigation of H2 emissions of a 2004 heavy-duty diesel engine supplemented with H2

Hydrogen (H₂) emissions characteristics of H₂-diesel dual fuel engine were measured using a 2004 turbocharged heavy-duty diesel engine with H₂ supplemented into the intake air. The emissions of H₂ were measured using an Electron Pulse Ionization (EPI) Mass Spectrometer (MS). The effect of the amount of H₂ added, the engine load, and diesel fuel flow rates on the emissions of H₂ and its combustion efficiency in the engine were investigated.     

Comparative study on the effect of CO2 and H2O dilution on laminar burning characteristics of CO/H2/air mixtures

A study on the effect of CO₂ and H₂O dilution on the laminar burning characteristics of CO/H₂/air mixtures was conducted at elevated pressures using spherically expanding flames and CHEMKIN package. Experimental conditions for the CO₂ and H₂O diluted CO/H₂/air/mixtures of hydrogen fraction in syngas from 0.2 to 0.8 are the pressures from 0.1 to 0.3 MPa, initial temperature of 373 K, with CO₂ or H₂O dilution ratios from 0 to 0.15. Laminar burning velocities of the CO₂ and H₂O diluted CO/H₂/air/mixtures were measured and calculated using the mechanism of Davis et al. and the mechanism of Li et al. Results show that the discrepancy exists between the measured values and the simulated ones using both Davis and Li mechanisms. The discrepancy shows different trends under CO₂ and H₂O dilution. Chemical kinetics analysis indicates that the elementary reaction corresponding to peak ROP of OH consumption for mixtures with CO/H₂ ratio of 20/80 changes from reaction R3 (OH + H₂ = H + H₂O) to R16 (HO₂+H = OH + OH) when CO₂ and H₂O are added. Sensitivity analysis was conducted to find out the dominant reaction when CO₂ and H₂O are added. Laminar burning velocities and kinetics analysis indicate that CO₂ has a stronger chemical effect than H₂O. The intrinsic flame instability is promoted at atmospheric pressure and is suppressed at elevated pressure for the CO₂ and H₂O diluted mixtures. This phenomenon was interpreted with the parameters of the effective Lewis number, thermal expansion ratio, flame thickness and linear theory.     

Carbon materials for H2 storage

In this work a series of carbons with different structural and textural properties were characterised and evaluated for their application in hydrogen storage. The materials used were different types of commercial carbons: carbon fibers, carbon cloths, nanotubes, superactivated carbons, and synthetic carbons (carbon nanospheres and carbon xerogels). Their textural properties (i.e., surface area, pore size distribution, etc.) were related to their hydrogen adsorption capacities. These H₂ storage capacities were evaluated by various methods (i.e., volumetric and gravimetric) at different temperatures and pressures. The differences between both methods at various operating conditions were evaluated and related to the textural properties of the carbon-based adsorbents. The results showed that temperature has a greater influence on the storage capacity of carbons than pressure. Furthermore, hydrogen storage capacity seems to be proportional to surface area, especially at 77 K. The micropore size distribution and the presence of narrow micropores also notably influence the H₂ storage capacity of carbons. In contrast, morphological or structural characteristics have no influence on gravimetric storage capacity. If synthetic materials are used, the textural properties of carbon materials can be tailored for hydrogen storage. However, a larger pore volume would be needed in order to increase storage capacity. It seems very difficult approach to attain the DOE and EU targets only by physical adsorption on carbon materials. Chemical modification of carbons would seem to be a promising alternative approach in order to increase the capacities.     

HDMR correlations for the laminar burning velocity of premixed CH4/H2/O2/N2 mixtures

Correlations for the laminar burning velocity of premixed CH₄/H₂/O₂/N₂ mixtures were developed using the method of High Dimensional Model Representation (HDMR). Based on experiment data over a wide range of conditions reported in the literature, two types of HDMR correlation (i.e. global and piecewise HDMR correlations) were obtained. The performance of these correlations was assessed through comparison with experimental results and the correlation reported in the literature. The laminar burning velocity predicted by the piecewise HDMR correlations was shown to agree very well with those from experiments. Therefore, the piecewise HDMR correlations can be used as an effective replacement for the full chemical mechanism when the prediction of the laminar burning velocity is needed in certain combustion modeling.     

CO2 and H2O gas conversion into CO and H2 using highly exothermic reactions induced by mixed industrial slags

This communication reports conversion phenomena in which CO₂ and H₂O gases are transformed into CO and H₂, respectively, when exposed to a mixture of molten CaO-rich metallurgical slag and V₂O₃-rich gasifier slag. On reaction, CO₂ and H₂O are thermodynamically driven to become CO and H₂, respectively, by giving up oxygen over the formation of calcium orthovanadate in the slag. The concept was experimentally investigated with a synthetic slag heated to 1500 °C (an assumed slag tap-out temperature in the metallurgical industry) in a CO₂ saturated atmosphere. On heating, a rapid drop in oxygen partial pressure occurred between 1405 °C and 1460 °C, where 97% of CO₂ transformed to CO. Potential industrial applications with the H₂O-to-H₂ conversion are then explored using detailed process computations. If the process is made economically viable, CO₂ and H₂O could be converted into products that are environmentally and industrially attractive and that have the potential for energy savings and greenhouse gas reduction in a process.