Design of a robust and efficient power electronic interface for the grid integration of solar photovoltaic generation systems

Nowadays, the penetration of photovoltaic (PV) solar power generation in distributed generation (DG) systems is growing rapidly. This condition imposes new requirements to the operation and management of the distribution grid, especially when high integration levels are achieved. Under this scenario, the power electronics technology plays a vital role in ensuring an effective grid integration of the PV system, since it is subject to requirements related not only to the variable source itself but also to its effects on the stability and operation of the electric grid. This paper proposes an enhanced interface for the grid connection of solar PV generation systems. The topology employed consists of a three-level cascaded Z-source inverter that allows the flexible, efficient and reliable generation of high quality electric power from the PV plant. A full detailed model is described and its control scheme is designed. The dynamic performance of the designed architecture is verified by computer simulations.     

A novel maximum power point tracker for thermoelectric generation system

In this paper, a novel hybrid maximum power point tracking (MPPT) method is proposed and investigated. The proposed MPPT technique combines the simplicity of perturb and observe (P&O) method and the fast tracking ability of open circuit voltage (OCV) method. The advantages of the proposed MPPT approach include fast tracking speed, no additional circuit required and no temporary power loss. To validate the feasibility of the proposed MPPT technique, an 1.2 kW thermoelectric generation system for industrial waste heat recovery is also constructed, experimental results show that comparing with conventional P&O technique, the proposed method can improve the tracking speed for 42.9% and 86.2% when temperature differences are ΔT = 60 °C and ΔT = 180 °C, respectively. Moreover, the energy loss can be improved by 24.0% and 87.0% when temperature differences are ΔT = 60 °C and ΔT = 180 °C, respectively.     

Adaptive maximum power point tracking control of fuel cell power plants

A fuel cell's output power depends nonlinearly on the applied current or voltage, and there exists a unique maximum power point (MPP). This paper reports a first attempt to trace MPPs by an extremum seeking controller. The locus of MPPs varies nonlinearly with the unpredictable variations in the fuel cell's operation conditions. Thus, a maximum power point tracking (MPPT) controller is needed to continuously deliver the highest possible power to the load when variations in operation conditions occur. A two-loop cascade controller with an intermediate converter is designed to operate fuel cell power plants at their MPPs. The outer loop uses an adaptive extremum seeking algorithm to estimate the real-time MPP, and then gives the estimated value to the inner loop as the set-point, at which the inner loop forces the fuel cell to operate. The proposed MPPT control system provides a simple and robust control law that can keep the fuel cell working at MPPs in real time. Simulation shows that this control approach can yield satisfactory results in terms of robustness toward variations in fuel cell operation conditions.     

Modeling and simulation of three phase multilevel inverter for grid connected photovoltaic systems

This paper presents a control for a three phase five-level neutral clamped inverter (NPC) for grid connected PV system. The maximum power point tracking (MPPT) is capable of extracting maximum power from the PV array connected to each DC link voltage level. The MPPT algorithm is solved by fuzzy logic controller. The fuzzy MPPT is integrated with the inverter so that a DC–DC converter is not needed and the output shows accurate and fast response. A digital PI current control algorithm is used to remain the current injected into the grid sinusoidal and to achieve high dynamic performance with low total harmonic distortion (THD). The validity of the system is verified through MATLAB/Simulink and the results are compared with three phase three-level grid connected NPC inverter in terms of THD.     

分布式光伏发电系统最大功率点跟踪技术比较研究

基于当前光伏阵列最大功率点跟踪技术的研究现状,介绍了适用于分布式光伏发电系统最大功率点跟踪的各种常用控制方法,阐述了每一种控制方法的技术原理,分析和比较了这些常用控制方法的特点,总结了各自的优点和缺点,最后对分布式光伏发电系统最大功率点跟踪方法的选择问题进行了探讨,并指出了具体选择方法时应综合考虑的各种因素。     

Comparative study and performance evaluation of central and distributed topologies of photovoltaic system

In this paper, we present a new alternative for improving both the performance of photovoltaic (PV) systems and the efficiency of the energy conversion by using different configuration of power converters. For this purpose, a comparative study between two configurations is carried out. The first configuration consists of a classical PV generator with a single centralized high power converter and the second one concerns a distributed topology. For this latter we use a certain number of PV strings with low power converters attached in series, in parallel or in a combination of series and parallel. Obviously the string topology has some advantages. Each power converter can control the power conversion of each module individually, which results in increased overall energy conversion of the entire system. The MPPT control system in this case can react effectively to atmospheric variations, to shading effect and to changes in the load. The PV system still operates even in case of failure on one of the power converters in a string. We simulated and compared the different conversion configurations in order to find the best one in terms of efficiency and produced energy. The obtained results are very interesting and can lead to optimal sizing and selection of best PV topology for a given application.     

A novel maximum power point tracking technique based on fuzzy logic for photovoltaic systems

Maximum power point tracking (MPPT) techniques are considered a crucial part in photovoltaic system design to maximise the output power of a photovoltaic array. Whilst several techniques have been designed, Perturb and Observe (P&O) is widely used for MPPT due to its low cost and simple implementation. Fuzzy logic (FL) is another common technique that achieves vastly improved performance for MPPT technique in terms of response speed and low fluctuation about the maximum power point. However, major issues of the conventional FL-MPPT are a drift problem associated with changing irradiance and complex implementation when compared with the P&O-MPPT. In this paper, a novel MPPT technique based on FL control and P&O algorithm is presented. The proposed method incorporates the advantages of the P&O-MPPT to account for slow and fast changes in solar irradiance and the reduced processing time for the FL-MPPT to address complex engineering problems when the membership functions are few. To evaluate the performance, the P&O-MPPT, FL-MPPT and the proposed method are simulated by a MATLAB-SIMULINK model for a grid-connected PV system. The EN 50530 standard test is used to calculate the efficiency of the proposed method under varying weather conditions. The simulation results demonstrate that the proposed technique accurately tracks the maximum power point and avoids the drift problem, whilst achieving efficiencies of greater than 99.6%.     

Modeling and maximum power point tracking (MPPT) method for PV array under partial shade conditions

Influenced by partial shade, PV module aging or fault, there are multiple peaks on PV array's output power–voltage (P–V) characteristic curve. Conventional maximum power point tracking (MPPT) methods are effective for single peak P–V characteristic under uniform solar irradiation, but they may fail in global MPP tracking under multi-peak P–V characteristics. Existing methods in literature for this problem are still unsatisfactory in terms of effectiveness, complexity and speed. In this paper, we first analyze the mathematical model of PV array that is suitable for simulation of complex partial shade situation. Then an adaptive MPPT (AMPPT) method is proposed, which can find real global maximum power point (MPP) for different partial shade conditions. When output characteristic of PV array varies, AMPPT will adjust tracking strategies to search for global peak area (GPA). Then it is easy for conventional MPPT to track the global MPP in GPA. Simulation and experimental results verify that the proposed AMPPT method is able to find real global MPP accurately, quickly and smoothly for complex multi-peak P–V characteristics. Comparison analysis results demonstrate that AMPPT is more effective for most shade types.     

A maximum power point tracking for photovoltaic-SPE system using a maximum current controller

Processes to produce hydrogen from solar photovoltaic (PV)-powered water electrolysis using solid polymer electrolysis (SPE) are reported. An alternative control of maximum power point tracking (MPPT) in the PV-SPE system based on the maximum current searching methods has been designed and implemented.Based on the characteristics of voltage–current and theoretical analysis of SPE, it can be shown that the tracking of the maximum current output of DC–DC converter in SPE side will track the MPPT of photovoltaic panel simultaneously.This method uses a proportional integrator controller to control the duty factor of DC–DC converter with pulse-width modulator (PWM).The MPPT performance and hydrogen production performance of this method have been evaluated and discussed based on the results of the experiment.     

通用型水泵电机的光伏驱动系统研究

目前光伏水泵的推广面临两个方面的障碍,一方面是应用较多的专用型光伏机泵成本较高;另一方面利用通用变频器驱动通用机泵时光伏利用率低。为了克服这些不足,设计了一种针对通用型水泵电机的光伏驱动系统。系统基于数字信号控制器dsPIC30F2010和IPM智能功率模块,实现了安全稳定运行、真正的最大功率跟踪（TMPPT）及模块化结构。分析了系统的硬件结构,探讨了系统的控制思想及实现,并用实验结果证明了设计的正确性。     

Maximum photovoltaic power tracking for the PV array using the fractional-order incremental conductance method

This paper proposes maximum photovoltaic power tracking (MPPT) for the photovoltaic (PV) array using the fractional-order incremental conductance method (FOICM). Since the PV array has low conversion efficiency, and the output power of PV array depends on the operation environments, such as various solar radiation, environment temperature, and weather conditions. Maximum charging power can be increased to a battery using a MPPT algorithm. The energy conversion of the absorbed solar light and cell temperature is directly transferred to the semiconductor, but electricity conduction has anomalous diffusion phenomena in inhomogeneous material. FOICM can provide a dynamic mathematical model to describe non-linear characteristics. The fractional-order incremental change as dynamic variable is used to adjust the PV array voltage toward the maximum power point. For a small-scale PV conversion system, the proposed method is validated by simulation with different operation environments. Compared with traditional methods, experimental results demonstrate the short tracking time and the practicality in MPPT of PV array.     

Power conversion system for high altitude wind power generation with medium voltage AC transmission

High Altitude Wind Power (HAWP) generating system provides clean energy at low cost and high capacity factor due to reduced size of the turbine and high speed streamlined wind at high altitude. An air-borne wind turbine (AWT) at high altitude extracts kinetic energy from wind using buoyancy provided by the blimp/aerostat. The generated electrical power is then transmitted to the ground based station (without any power conditioning) using the transmission lines (tether). The power conversion system (PCS) for harnessing HAWP is proposed in this paper. The proposed PCS consists of a three-level neutral point clamped (NPC) rectifier, a three-level NPC DC–DC converter followed by a two-level inverter. Modelling, design and control of the PCS are presented and discussed. The PCS provides generation side maximum power-point tracking (MPPT) using sensorless optimal torque control technique. The DC–DC converter provides electrical isolation as well as voltage step-down functions. A modified proportional resonant (PR) control which can selectively eliminate lower order current harmonics of the grid-connected inverter is also presented. The proposed control scheme of the PCS is evaluated through simulation studies using software programs like PSIM and MATLAB. A scaled-down 1 kW laboratory prototype of the complete PCS is designed, built and tested. The experimental test results obtained validate the proposed control scheme for efficient power generation from high altitude wind and interface to the grid/load.     

SMC-DPC based active and reactive power control of grid-tied three phase inverter for PV systems

In this paper, sliding mode control (SMC) – direct power controller (DPC) based active and reactive power controller for three-phase grid-tied photovoltaic (PV) system is proposed. The proposed system consists of two main controllers: the DC/DC boost converter to track the possible maximum power from the PV panels and the grid-tied three-phase inverter. The Perturb and Observe (P&O) algorithm is used to transfer the maximum power from the PV panels. Control of the active and reactive powers is performed using the SMC-DPC strategy without any rotating coordinate transformations or phase angle tracking of the grid voltage. In addition, extra current control cycles are not used to simplify the system design and to increase transient performance. The fixed switching frequency is obtained by using space vector modulation (SVM). The proposed system provides very good results both in transient and steady states with the simple algorithms of P&O and SMC-DPC methods. Moreover, the results are evaluated by comparing the SMC-DPC method developed for MPPT and the traditional PI control method. The proposed controller method is achieved with TMS320F28335 DSP processor and the system is experimentally tested for 12 kW PV generation systems.     

A miniaturized power generation system cascade utilizing thermal energy of a micro-combustor: Design and modelling

Currently, combustion-based micro power devices encounter the problem of low conversion efficiency. A miniaturized power generation system cascade utilizing thermal energy of a micro-combustor is proposed, because thermophotovoltaic (TPV) cells and thermoelectric (TE) modules work at different temperature levels. The system consists of a planar micro-combustor with a bended extension at the exit, two GaSb TPV modules to convert high temperature thermal radiation and two Bi–Te based TE modules attached to the bended extension to harness medium temperature thermal energy. The mathematical modelling approach to quantify the power output and conversion efficiency is systematically presented. The modelling results show that the integration of the TE modules could significantly improve the system efficiency. When burning the H₂/air mixture, the overall system efficiency could reach 2.5% under the flow condition of U₀ = 3 m/s and Φ = 1.0. Finally, measures for better thermal management to further enhance the conversion efficiency are discussed.     

A novel adaptative maximum power point tracking algorithm for small wind turbines

A novel maximum power point tracking algorithm for small wind turbines is proposed. The solution presented here is an adaptive intelligent algorithm that uses a new advanced perturb and observe method to search for the optimum relationship of the system for tracking the maximum power point even under variable wind conditions. The validity of the proposed algorithm is analysed and the design procedure is presented. Its main virtue resides in its capability to adapt to changes in the turbine and in the surrounding environment, even under variable wind conditions, improving the efficiency of the system. The experimental results confirm the validity of the proposed algorithm.     

Probabilistic Wavelet Fuzzy Neural Network based reactive power control for grid-connected three-phase PV system during grid faults

This study presents a reactive power controller using Probabilistic Wavelet Fuzzy Neural Network (PWFNN) for grid-connected three-phase PhotoVoltaic (PV) system during grid faults. The controller also considers the ratio of the injected reactive current to meet the Low Voltage Ride Through (LVRT) regulation. Moreover, the balance of the active power between the PV panel and the grid-connected inverter during grid faults is controlled by the dc-link bus voltage. Furthermore, to reduce the risk of over-current during LVRT operation, a current limit is predefined for the injection of reactive current. The main contribution of this study is the introduction of the PWFNN controller for reactive and active power control that provides LVRT operation with power balance under various grid fault conditions. Finally, some experimental tests are realized to validate the effectiveness of the proposed controller.     

基于实测数据的光伏阵列参数辨识与输出功率预测

基于光伏电池的I-U方程、基本电路理论和最大功率跟踪的输出特性,提出了运用参数辨识方法及光伏阵列的输入、输出数据,辨识光伏阵列光生电流、反向饱和电流、二极管理想因子、电池串联内阻4个待定系数,确定光伏阵列的I-U方程,再用求解得到的I-U方程来预测光伏电站的输出功率。通过算例和实测数据仿真比较,验证了所提出方法的可行性和准确性。     

PSO-based MPPT control of wind-driven Self-Excited Induction Generator for pumping system

In recent years, much research has been done to improve the performance of a wind energy conversion system at various wind speeds using Maximum Power Point Tracking (MPPT) algorithms to find an efficient production of peak energy.In most cases, the MPPT techniques used to maximize the turbines power coefficient neglect the effect of losses generated by the system components, which can shift the true optimal operating point of the wind turbine. Furthermore, conventional MPPT methods such as Perturbation and Observation (P&O) and Incremental of Conductance (IncCond), need to sense both the rotor speed and the power of the wind turbine. In addition, other methods such as Fuzzy Logic and neural networks based on MPPT algorithms are proposed but these methods require knowledge of the wind speed and system parameters for the training phase.In this context, a new MPPT technique is being proposed in this paper, based on Particle Swarm Optimization (PSO) for a standalone Self-Excited Induction Generator (SEIG) operating at variable wind speed and supplying an induction motor coupled to a centrifugal pump.     

Evaluation of performance of photovoltaic system with maximum power point (MPP)

Performance of the photovoltaic system is highly influenced by the weather, especially the irradiation and the temperature. To simplify the design of solar generator power, a mathematical model and its validity of the solar cell are required. In this work, the value of the parameters in the mathematical model is obtained by the measurement of the I–V curve of the module. To get an I–V curve, one of the modules in the system was radiated and loaded by a load simulator. A photovoltaic pumping system with maximum power point tracker was built and tested. The results were analyzed and evaluated by using the parameters and the photovoltaic system was shown to be well optimized.     

Multilevel converters control for renewable energy integration to the power grid

The paper deals with the multilevel converters control strategy for renewable energy resources integration in distribution grids. The proposed control scheme ensures the injection of the generated power in the distribution grid with fast dynamic response, while providing an additional active power filtering capability providing the required harmonic and reactive currents to the considered non-linear loads. The proposed control scheme is applicable to a general multilevel converter and to any types of the renewable energy resources. The control scheme is validated by means of simulations with a three-level diode-clamped converter which interfaces a wind power generation system to a distribution grid supplying non-linear loads. From extensive simulation results, high performance of this control strategy in renewable energy application is demonstrated with reduced total harmonic distortion, increased power factor and compensated load’s reactive powers.