Operational characteristics of a passive air-breathing direct methanol fuel cell under various structural conditions

The operational characteristics of a small-scale passive air-breathing direct methanol fuel cell (PAB-DMFC) are comprehensively investigated under both steady-state and dynamic conditions. As the most important operating parameter, methanol concentration has significant effects on the cell performance. For different methanol concentrations (e.g., 0.5 and 8 M), the structural adaptations are particularly discussed. The results show that the structural factors are closely related to the influence degree of methanol concentration. In this study, the characteristics of the open circuit voltage (OCV) under various structural and methanol-concentration conditions are presented. Besides, the effects of other operating conditions such as running time, forced air convection and refueling action on the cell performance are also evaluated. In addition, a series of dynamic operations of the PAB-DMFC are conducted under different load cycles. Accordingly, the transient phenomena such as voltage undershoot and overshoot are explored. A fundamental principle for evaluating the operational characteristics of a PAB-DMFC is to simultaneously take into account the mass transfer requirements such as reactant delivery, product removal, methanol/water crossover control and so on.     

Effects of structural aspects on the performance of a passive air-breathing direct methanol fuel cell

This study systematically investigates the effects of structural aspects on the performance of a passive air-breathing direct methanol fuel cell (DMFC). Three factors are selected in this study: (1) two different open ratios of the current collector; (2) two different assembly methods of the diffusion layer; and (3) three membrane types with different thicknesses. The interrelations and interactions among these factors have been taken into account. The results demonstrate that these structural factors combine to significantly affect the cell performance of DMFCs. The higher open ratio not only provides a larger area for mass transfer passage and facilitates removal of the products, but also promotes higher methanol crossover. The hot-pressed diffusion layer (DL) can mitigate methanol permeation while the non-bonded variant is able to enhance product removal. The increase of membrane thickness helps obtain a lower methanol crossover rate and higher methanol utilisation efficiency, but also depresses cell performance under certain conditions. In this research, the maximum power density of 10.7 mW cm⁻² is obtained by selecting the current collector with a lower open ratio, the non-bonded DL, and the Nafion 117 membrane. The effect of methanol concentration on the performance of DMFCs is also explored.     

Dominance evaluation of structural factors in a passive air-breathing direct methanol fuel cell based on orthogonal array analysis

This study comprehensively investigates the dominance of various structural factors in a passive air-breathing DMFC by means of orthogonal array analysis (OAA). Two membrane types, two assembly patterns of the diffusion layer and two open ratios of the current collector are prepared. Three target variables are selected as the performance indexes including the maximum power density (MPD), limiting current density (LCD) and open circuit voltage (OCV). The range analysis (RA) method and effect curves (ECs) are used to characterize the OAA data. The RA results demonstrate that the current collector and diffusion layer combine to dominate the values of MPD and LCD in a wide range of methanol concentrations from 0.5 to 8 M. The dominant structural factors related to the value of OCV at different methanol concentrations are also explored. In addition, the effect curves show that a medium methanol concentration like 2 M generally promotes higher values of MPD and LCD, while a relatively lower methanol concentration like 0.5 M benefits a higher value of OCV than others in a general statistical sense.     

Performance of air-breathing direct methanol fuel cell with anion-exchange membrane

This report details development of an air-breathing direct methanol alkaline fuel cell with an anion-exchange membrane. The commercially available anion-exchange membrane used in the fuel cell was first electrochemically characterized by measuring its ionic conductivity, and showed a promising result of 1.0 × 10⁻¹ S cm⁻¹ in a 5 M KOH solution. A laboratory-scale direct methanol fuel cell using the alkaline membrane was then assembled to demonstrate the feasibility of the system. A high open-circuit voltage of 700 mV was obtained for the air-breathing alkaline membrane direct methanol fuel cell (AMDMFC), a result about 100 mV higher than that obtained for the air-breathing DMFC using a proton exchange membrane. Polarization measurement revealed that the power densities for the AMDMFC are strongly dependent on the methanol concentration and reach a maximum value of 12.8 mW cm⁻² at 0.3 V with a 7 M methanol concentration. A durability test for the air-breathing AMDMFC was performed in chronoamperometry mode (0.3 V), and the decay rate was approximately 0.056 mA cm⁻² h⁻¹ over 160 h of operation. The cell area resistance for the air-breathing AMDMFC was around 1.3 Ω cm² in the open-circuit voltage (OCV) mode and then is stably supported around 0.8 Ω cm² in constant voltage (0.3 V) mode.     

Study on operational aspects of a passive direct methanol fuel cell incorporating an anodic methanol barrier

This paper presents an investigation concerning the effects of operating conditions on the performance of a passive direct methanol fuel cell (DMFC). A self-developed porous metal fiber sintered plate (PMFSP) is used as the methanol barrier between the fuel reservoir and current collector at the anode in order to alleviate the effect of methanol crossover. The effectiveness of using this method is validated. A series of operating conditions such as operating orientation, methanol concentration, ambient temperature, forced air convection and dynamic load are evaluated. Results show that the use of a PMFSP promotes a higher cell performance during vertical operation than horizontal orientation. The effect of methanol concentration depends on the PMFSP porosity. A relatively lower porosity is favorable for high-concentration operation. The cell performance gets improved when increasing the ambient temperature and adopting forced air supply at the cathode. Compared with the traditional structure, the use of a PMFSP makes the fuel cell insensitive to the change of blowing intensity. In addition, the dynamic characteristics of the PMFSP-based passive DMFC are also reported.     

Lightweight current collector based on printed-circuit-board technology and its structural effects on the passive air-breathing direct methanol fuel cell

To realize lightweight design of the fuel cell system is a critical issue before it is put into practical use. The printed-circuit-board (PCB) technology can be potentially used for production of current collectors or flow distributors. This study develops prototypes of a single passive air-breathing direct methanol fuel cell (DMFC) and also an 8-cell mono-polar DMFC stack based on PCB current collectors. The effects of diverse structural and operational factors on the cell performance are explored. Results show that the methanol concentration of 6 M promotes a higher cell performance with a peak power density of 18.3 mW cm⁻². The combination of current collectors using a relatively higher anode open ratio and inversely a lower cathode open ratio helps enhance the cell performance. Dynamic tests are also conducted to reveal transient behaviors and its dependence on the operating conditions. To validate the real working status of the DMFC stack, it is coupled with an LED lightening system. The performance of this hybrid system is also reported in this study.     

Exergy analysis of a passive direct methanol fuel cell

An analytical, one-dimensional, steady state model is employed to solve for overpotentials at the catalyst layers along with the liquid water and methanol distributions at the anode, and oxygen transport at the cathode. An iterative method is utilized to calculate the cell temperature at each cell current density. A comprehensive exergy analysis considering all possible species inside the cell during normal operation is presented. The contributions of different types of irreversibilities including overpotentials at the anode and cathode, methanol crossover, contact resistance, and proton conductivity of the membrane are investigated. Of all losses, overpotentials in conjunction with the methanol crossover are considered as the major exergy destruction sources inside the cell during the normal operation. While the exergy losses due to electrochemical reactions are more significant at higher current densities, exergy destruction by methanol crossover at the cathode plays more important role at lower currents. It is also found that the first-law efficiency of a passive direct methanol fuel cell increases as the methanol solution in the tank increases in concentration from 1 M to 3 M. However, this is not the case with the second-law efficiency which is always decreasing as the concentration of the methanol solution in the tank increases.     

Performance of air-breathing direct methanol fuel cell with Au-coated aluminum current collectors

Current collectors of the direct methanol fuel cell (DMFC) are of significant importance for portable power sources, and greatly determine the weight energy density and cost of the cell. In this paper, the air-breathing aluminum (Al) current collectors have been developed for powering portable applications. The anode and cathode current collectors with the area of 4.5 cm² were fabricated on the Al substrates utilizing Computer Numerical Control (CNC) technology. To obtain strong anti-corrosion resistance, a 3-μm-Au layer was deposited on the current collectors using chemical plating. Compared with the graphite and stainless steel, the characterization of the Au-coated Al current collector was investigated to exhibit superior characteristics in electric conductivity, weight and electrochemical corrosion resistance. The current collector was applied to a DMFC and the cell performance was experimentally investigated under different operating conditions. The measured maximum power density of the DMFC could reach 19.8 mW cm⁻² at current density of 98 mA cm⁻² with 2 M methanol solutions. The results indicated that the Au-coated Al current collectors presented in this paper might be helpful for the development of portable power sources applied in future commercial applications.     

Performance evaluation of passive direct methanol fuel cell with methanol vapour supplied through a flow channel

This work examines the effect of fuel delivery configuration on the performance of a passive air-breathing direct methanol fuel cell (DMFC). The performance of a single cell is evaluated while the methanol vapour is supplied through a flow channel from a methanol reservoir connected to the anode. The oxygen is supplied from the ambient air to the cathode via natural convection. The fuel cell employs parallel channel configurations or open chamber configurations for methanol vapour feeding. The opening ratio of the flow channel and the flow channel configuration is changed. The opening ratio is defined as that between the area of the inlet port and the area of the outlet port. The chamber configuration is preferred for optimum fuel feeding. The best performance of the fuel cell is obtained when the opening ratio is 0.8 in the chamber configuration. Under these conditions, the peak power is 10.2 mW cm⁻² at room temperature and ambient pressure. Consequently, passive DMFCs using methanol vapour require sufficient methanol vapour feeding through the flow channel at the anode for best performance. The mediocre performance of a passive DMFC with a channel configuration is attributed to the low differential pressure and insufficient supply of methanol vapour.     

Water and air management systems for a passive direct methanol fuel cell

In this paper water and air management systems were developed for a miniature, passive direct methanol fuel cell (DMFC). The membrane thickness, water management system, air management system and gas diffusion electrodes (GDE) were examined to find their effects on the water balance coefficient, fuel utilization efficiency, energy efficiency and power density. Two membranes were used, Nafion^® 112 and Nafion^® 117. Nafion^® 117 cells had greater water balance coefficients, higher fuel utilization efficiency and greater energy efficiency. A passive water management system which utilizes additional cathode gas diffusion layers (GDL) and a passive air management system which makes use of air filters was developed and tested. Water management was improved with the addition of two additional cathode GDLs. The water balance coefficients were increased from −1.930 to 1.021 for a cell using a 3.0 mol kg⁻¹ solution at a current density of 33 mA cm⁻². The addition of an air filter further increased the water balance coefficient to 1.131. Maximum power density was improved from 20 mW cm⁻² to 25 mW cm⁻² for 3.0 mol kg⁻¹ solutions by upgrading from second to third generation GDEs, obtained from E-TEK. There was no significant difference in water management found between second and third generation GDEs. A fuel utilization efficiency of 63% and energy efficiency of 16% was achieved for a 3.0 mol kg⁻¹ solution with a current density of 66 mA cm⁻² for third generation GDEs.     

Development of an air-breathing direct methanol fuel cell with the cathode shutter current collectors

An air-breathing direct methanol fuel cell with a novel cathode shutter current collector is fabricated to develop the power sources for consumer electronic devices. Compared with the conventional circular cathode current collector, the shutter one improves the oxygen consumption and mass transport. The anode and cathode current collectors are made of stainless steel using thermal stamping die process. Moreover, an encapsulation method using the tailor-made clamps is designed to assemble the current collectors and MEA for distributing the stress of the edges and inside uniformly. It is observed that the maximum power density of the air-breathing DMFC operating with 1 M methanol solution achieves 19.7 mW/cm² at room temperature. Based on the individual DMFCs, the air-breathing stack consisting of 36 DMFC units is achieved and applied to power a notebook computer.     

A direct methanol fuel cell system with passive fuel delivery based on liquid surface tension

The existing direct methanol fuel cell (DMFC) systems are fed with a fixed concentration of fuel, which are either a diluted methanol solution or an active fuel delivery driven by an attached active pump. Both approaches limit the power conversion density or degrade the overall efficiency of the DMFC system significantly. Such disadvantages become more severe in small-scale DMFCs, which require a high conversion efficiency and a small physical space suitable for portable electronics. In this paper, passive fuel delivery based on a surface tension driving mechanism was designed and integrated in a laboratory-made prototype to achieve consumption depending on fuel concentration and power-free fuel delivery. Unidirectional methanol-to-water smooth flow is achieved through the capillaries of a Teflon PTFE (polytetrafluoroethylene) membrane based on the difference in liquid surface tension. The prototype was demonstrated to exhibit a better polarization performance and to last for an extended operating time compared to conventional DMFCs. Its high efficiency and load regulation performance were also demonstrated in contrast to an active DMFC supplied with a constant concentration fuel. The fuel delivery driven by the liquid surface tension effect demonstrated here is believed to be more applicable for future small-scale DMFCs for portable electronics.     

Performance and design analysis of tubular-shaped passive direct methanol fuel cells

To achieve the maximum performance from a Direct Methanol Fuel Cell (DMFC), one must not only investigate the materials and configuration of the MEA layers, but also consider alternative cell geometries that produce a higher instantaneous power while occupying the same cell volume. In this work, a two-dimensional, two-phase, non-isothermal model was developed to investigate the steady-state performance and design characteristics of a tubular-shaped, passive DMFC. Under certain geometric conditions, it was found that a tubular DMFC can produce a higher instantaneous Volumetric Power Density than a planar DMFC. Increasing the ambient temperature from 20 to 40 °C increases the peak power density produced by the fuel cell by 11.3 mW cm⁻² with 1 M, 16.3 mW cm⁻² with 2 M, but by only 8.4 mW cm⁻² with 3 M methanol. The poor performance with 3 M methanol at a higher ambient temperature is caused by increased methanol crossover and significant oxygen depletion along the Cathode Transport Layer (CTL). For a 5 cm long tubular DMFC to maintain sufficient Oxygen transport, the thickness of the CTL must be greater than 1 mm for 1 M operation, greater than 5 mm for 2 M operation, and greater than 10 mm for 3 M or higher operation.     

Single passive direct methanol fuel cell supplied with pure methanol

A new single passive direct methanol fuel cell (DMFC) supplied with pure methanol is designed, assembled and tested using a pervaporation membrane (PM) to control the methanol transport. The effect of the PM size on the fuel cell performances and the constant current discharge of the fuel cell with one-fueling are studied. The results show that the fuel cell with PM 9 cm² can yield a maximum power density of about 21 mW cm⁻², and a stable performances at a discharge current of 100 mA can last about 45 h. Compared with DMFC supplied with 3 M methanol solution, the energy density provided by this new DMFC has increased about 6 times.     

Vapor feed direct methanol fuel cells with passive thermal-fluids management system

The present paper describes a novel technology that can be used to manage methanol and water in miniature direct methanol fuel cells (DMFCs) without the need for a complex micro-fluidics subsystem. At the core of this new technology is a unique passive fuel delivery system that allows for fuel delivery at an adjustable rate from a reservoir to the anode. Furthermore, the fuel cell is designed for both passive water management and effective carbon dioxide removal. The innovative thermal management mechanism is the key for effective operation of the fuel cell system. The vapor feed DMFC reached a power density of 16.5 mW cm⁻² at current density of 60 mA cm⁻². A series of fuel cell prototypes in the 0.5 W range have been successfully developed. The prototypes have demonstrated long-term stable operation, easy fuel delivery control and are scalable to larger power systems. A two-cell stack has successfully operated for 6 months with negligible degradation.     

Transient behavior analysis of a new designed passive direct methanol fuel cell fed with highly concentrated methanol

A new structure of passive direct methanol fuel cell (DMFC) with two methanol reservoirs separated by a porous medium layer is designed and a corresponding mathematical model is presented. The new designed passive DMFC can be directly fed with highly concentrated methanol solution or neat methanol. The porosity (?_pr) of the porous medium layer is optimized using the proposed model. Some operation parameters are also optimized by both the numerical calculation and experimental measurement. The new designed DMFC can be continuously operated for about 4.5 times longer than a conventional passive DMFC with the optimum parameters. The methanol crossover during the same discharging is only about 50% higher.     

Modeling and optimizing the performance of a passive direct methanol fuel cell

Passive direct methanol fuel cells (DMFCs) are promising energy sources for portable electronic devices. Different from DMFCs with active fuel feeding systems, passive DMFCs with nearly stagnant fuel and air tend to bear comparatively less power densities. In the aspect of cell performance optimization, there could be significant differences in cell design parameters between active and passive DMFCs. A numerical model that could simulate methanol permeation and the pertinent mixed potential effect in a DMFC was used to help seek for possibilities of optimizing the cell performance of a passive DMFC by studying impacts from variations of cell design. The subjects studied include catalysis of the anode and the cathode, membrane thickness, membrane conductivity, and methanol concentration. In contrast to general understandings on a DMFC with active fuel and reactant gas, our simulation results for a passive DMFC used in this study indicated that the catalysis of the cathode appeared to be the most important parameter. The maximum power density was predicted to improve by 38% with the thickness of the cathodic catalyst layer doubled and by 36% with the catalyst loading doubled. The improvement on cell performance would multiply if we simultaneously adopted the most optimal parameters during the simulation study.     

Toward using porous metal-fiber sintered plate as anodic methanol barrier in a passive direct methanol fuel cell

A porous metal-fiber sintered plate (PMFSP) based on multi-tooth cutting and high-temperature solid-phase sintering is used as the methanol barrier at the anode of a passive DMFC in order to reduce the effect of methanol crossover. Its roles in controlling the mass transfer mechanisms related to reactant supply and product removal are also considered in this study. Results show that the cell performance can be significantly improved by using such a macroporous material, especially at a higher methanol concentration. The porosity of the PMFSP has great effects on the cell performance in the form of interacting with the current collector setup. When the combination of anodic circular-hole-array with an open ratio of 28.3% and cathodic parallel fence with 58% is used, it is favorable to use a lower porosity of 70%. When the above current collectors are reversed, a higher porosity of 80% is recommended. Results also demonstrate that the PMFSP with a medium thickness of 2 mm achieves a higher cell performance. Moreover, the PMFSP assembled in an outside manner is proved to be more able to enhance the cell performance than that based on inside-type. The mechanisms related to the roles of the PMFSP in mass transfer process are provided in detail.     

A self-regulated passive fuel-feed system for passive direct methanol fuel cells

Operating a passive direct methanol fuel cell (DMFC) with high methanol concentration is desired because this increases the energy density of the fuel cell system and hence results in a longer runtime. However, the increase in methanol concentration is limited by the adverse effect of methanol crossover in the conventional design. To overcome this problem, we propose a new self-regulated passive fuel-feed system that not only enables the passive DMFC to operate with high-concentration methanol solution without serious methanol crossover, but also allows a self-regulation of the feed rate of methanol solution in response to discharging current. The experimental results showed that with this fuel-feed system, the fuel cell fed with high methanol concentration of 12.0 M yielded the same performance as that of the conventional DMFC running with 4.0 M methanol solution. Moreover, as a result of the increased energy density, the runtime of the cell with this new system was as long as 10.1 h, doubling that of the conventional design (4.4 h) at a given fuel tank volume. It was also demonstrated that this passive fuel-feed system could successfully self-regulate the fuel-feed rate in response to the change in discharging currents.     

Design and simulation of a liquid electrolyte passive direct methanol fuel cell with low methanol crossover

This study investigates an aqueous solution of sulfuric acid that serves as the liquid electrolyte (LE) in a passive direct methanol fuel cell (DMFC). The addition of an LE can reduce methanol crossover and increase the fuel utilization significantly. To improve the performance of an LE-DMFC, a mathematical model is developed to optimize the thicknesses of both the LE layer and the Nafion membrane. The maximum power density of the LE-DMFC is improved by approximately 30% compared with a conventional DMFC (C-DMFC) when each is fed by methanol solutions of the same concentration. Due to the low methanol crossover of the LE-DMFC, a highly concentrated methanol solution can be directly fed into the LE-DMFC. The discharge time and volume energy density of the LE-DMFC are two times longer and three times greater than those of the C-DMFC, respectively. In addition, fuel utilization increases by approximately 100%.