Synthesis, characterization and thermal properties of soluble aromatic poly(amide imide)s

Novel diamines such as N,N′-bis(aminoaryl)terephthalamido-2-carboxylic acids (BATCA), which contain primary amine, amide and carboxylic acid groups and are soluble in dilute aqueous NaOH solution, were synthesized by reacting aromatic diamines with trimellitic anhydride chloride in dimethylformamide. Poly(amide imide)s containing 3:1 ratio of amide:imide groups in the polymer chain were prepared by low temperature solution polymerization of BATCAs with isophthaloyl chloride or terephthaloyl chloride in dimethylformamide at 5-10 °C to form poly(amide amic acid)s, and followed by treating with a mixture of triethylamine and acetic anhydride. The PAIs were soluble in polar aprotic solvents like dimethylformamide, dimethylacetamide, dimethylsulphoxide and N-methylpyrrolidone, and have inherent viscosities in the range of 0.30-0.66 dL/g. The PAIs were characterized by IR, ¹H NMR and ¹³C NMR techniques. Thermogravimetric analysis (TGA) has shown that the initial decomposition temperatures of the polymers are in the range of 250-440 °C, depending upon the structures of diamine and diacid chloride. The glass transition temperatures of the PAIs are in the range of 128-320 °C. The IDT and T_g values of the polymers containing terephthaloyl unit are higher by about 20-40 °C than those of the polymers with isophthaloyl unit. BATCA could be utilized for the preparation of thin film composite membranes having PAA/PAI barrier layer on PES by in situ interfacial polymerization with IPC/TPC/TMC.     

Synthesis and characterization of temperature-responsive copolymer of PELGA modified poly(N-isopropylacrylamide)

Novel amphiphilic PELGA modified temperature-responsive copolymer, [(poly(methoxyethylene glycol)-co-poly(lactic acid)-co-poly-(glycolic acid))acrylate-co-poly(N-isopropylacrylamide)-co-poly(N-hydroxymethylacrylamide)] (PELGAA-co-PNIPAAm-co-PNHMAAm) was synthesized by incorporating PELGA as the amphiphilic moiety into poly(N-isopropylamide) with various LA/GA ratios. Polymers obtained were characterized by FT-IR, GPC, ¹H-NMR and DSC. The lower critical solution temperature (LCST) of the copolymeric nanoparticles was 40±0.6 °C, the critical aggregation concentration (CAC) was 18 mg L⁻¹, and reversible change in nanoparticle size related to temperature was fluctuated between 210±10 and 109±26 nm, while change in zeta potential of the nanoparticles was between −36±6 and −26±4 mV. The transmission electron microscopy (TEM) images of nanoparticles were also presented.     

Synthesis and thermally responsive characteristics of dendritic poly(ether-amide) grafting with PNIPAAm and PEG

A series of thermally responsive dendritic core-shell polymers were prepared based upon dendritic poly(ether-amide) (DPEA), modified with carboxyl end-capped linear poly(N-isopropylacrylamide) (PNIPAAm-COOH) or both PNIPAAm-COOH and carboxyl end-capped methoxy polyethylene glycol (PEG-COOH) in different ratios via an esterification process to obtain DPEA-PNIPAAm or DPEA-PNIPAAm-PEG. Their molecular structures were verified by gel permeation chromatography, and ¹H NMR and FTIR spectroscopy. The temperature-dependent characteristics study has revealed that DPEA-PNIPAAm exhibits a lower critical solution temperature (LCST) of about 34 °C, whereas DPEA-PNIPAAm-PEG polymers with the PNIPAAm/PEG ratio of about 1.0 and 0.4 possess about 36 °C and 39 °C, respectively, compared with 32 °C for homopolymer PNIPAAm. The critical aggregation temperature was investigated using fluorescence excitation spectrum of pyrene as a sequestered guest molecule based upon the sharp increase of the I₃₃₈/I₃₃₃ value.     

Gel polymer electrolyte based on poly(acrylonitrile-co-styrene) and a novel organic iodide salt for quasi-solid state dye-sensitized solar cell

A gel polymer electrolyte based on poly(acrylonitrile-co-styrene) as polymer matrix and N-methyl pyridine iodide salt as I⁻ source was prepared. Controlling the concentration of polymer matrix of poly(acrylonitrile-co-styrene) at 17.5 wt.%, mixing the binary organic solvents mixture ethylene carbonate and propylene carbonate with 6:4 (w/w), and the concentration of N-methyl pyridine iodide and iodine with 0.5 and 0.05 M, respectively, the gel polymer electrolyte attains the maximum ionic conductivity (at 30 °C) of 4.63 mS cm⁻¹. Based on the gel polymer electrolyte, a quasi-solid state dye-sensitized solar cell was fabricated and its overall energy conversion efficiency of light-to-electricity of 3.10% was achieved under irradiation of 100 mW cm⁻².     

Temperature sensitive poly(N-t-butylacrylamide-co-acrylamide) hydrogels: synthesis and swelling behavior

A series of temperature sensitive hydrogels was prepared by free-radical crosslinking copolymerization of N-t-butylacrylamide (TBA) and acrylamide in methanol. N,N′-methylenebis(acrylamide) was used as the crosslinker. It was shown that the swelling behavior of the hydrogels can be controlled by changing the amount of TBA units in the network chains. Hydrogels immersed in dimethylsulfoxide (DMSO)-water mixtures exhibited reentrant swelling behavior, in which the gels first deswell then reswell if the DMSO content of the solvent mixture is continuously increased. In water over the temperature range of 2-64 °C, hydrogels with less than 40[percnt] TBA by mole were in a swollen state while those with TBA contents higher than 60[percnt] were in a collapsed state. Hydrogels with 40-60[percnt] TBA exhibited swelling-deswelling transition in water depending on the temperature. The temperature interval for the deswelling transition of 60[percnt] TBA gel was found to be in the range from 10 to 28 °C, while for the 40[percnt] TBA gel, the deswelling started at about 20 °C and continued until the onset of the hydrolysis of the network chains at around 64 °C. It was shown that the Flory-Rehner theory of swelling equilibrium provides a satisfactory agreement to the experimental swelling data of the hydrogels, provided that the sensitive dependence of the χ parameter on both temperature and polymer concentration is taken into account.     

Toward an understanding of thermoresponsive transition behavior of hydrophobically modified N-isopropylacrylamide copolymer solution

Poly(N-isopropylacrylamide-co-vinyl laurate)(PNIPAAm-co-VL) copolymers were prepared at various feed ratios via conventional radical random copolymerization. The formation, composition ratios and molecular weight of copolymers were examined. The thermoresponsive behaviors of PNIPAAm and PNIPAAm-co-VL solutions at low and high concentrations were intensively investigated by turbidity measurement, Micro-DSC, temperature-variable state fluorescence, ¹H NMR and dynamic light scattering (DLS). Several important results were obtained that (1) incorporation of PVL results in much lower and broader LCST regions of the copolymer solutions, and facilitates the formation of hydrophobic microdomains far below LCST, causing a pronounced aggregation in solutions (2) temperature-variable ¹H NMR spectra shows that during the phase transition, the ‘penetration’ of PNIPAAm into the hydrophobic core is a process accompanied with a transition of isopropyl from hydration to dehydration as well as a self-aggregation of hydrophobic chains at different temperature stages (3) according to the ¹H NMR spectra of polymer solutions obtained at varied temperatures, the microdomains from hydrophobic VL moieties have a different accessibility for isopropyl groups and the entire chains during phase transition (4) temperature-variable DLS demonstrates that the temperature-induced transition behavior of copolymers is supposedly divided into three stages: pre-LCST aggregation (<20 °C), coil-globule transition at LCST (20-25 °C) and post-LCST aggregation (>25 °C).     

Biomolecule and surfactant-assisted hydrothermal synthesis of PbS crystals

PbS crystals were hydrothermally synthesized using Pb(NO₃)₂, l-cysteine, and N-cetyl pyridinium chloride in solutions with different pH values at 140 °C. Flower-like, granular and truncated cubic PbS crystals composing of Pb and S were detected using an X-ray diffractometer (XRD), a scanning electron microscope (SEM), a transmission electron microscope (TEM), a selected area electron diffraction (SAED) technique and an energy dispersive X-ray (EDX) analyzer. In addition, a Raman spectrometer revealed the presence of the first and second overtone modes at 436 and 602 cm⁻¹, respectively. Emission spectra of the products were detected at 412 nm using a photoluminescence (PL) spectrometer.     

Synthesis of new N, N-diphenylhydrazone dyes for solar cells: Effects of thiophene-derived π-conjugated bridge

Four novel D-π-A hydrazone dyes (HT, HM, HE, and HO) with an N, N-diphenylhydrazone moiety as the electron donor, different thiophene-derived π-conjugated bridges and a cyanoacrylic acid moiety as the electron acceptor have been designed and synthesized for the application in dye-sensitized solar cells. The influences of thiophene-derived bridges on the photoelectrochemical and photovoltaic performance of these hydrazone dyes were investigated. Results demonstrate that the introduction of 3,4-dialkyloxythiophene could red-shift the dye’s absorption spectrum due to the enhancement of the electron-donating ability of π-conjugated bridges. Importantly, electrochemical impedance spectroscopy analysis reveal that 3,4-dialkyloxythiophene bridge could change the charge recombination resistance at the TiO₂/dye/electrolyte interface and as a result to improve the open-circuit photovoltage. Among the four dyes, HO exhibits the maximum power conversion efficiency of 5.83% (V_oc = 0.65 V, J_sc = 12.69 mA/cm², FF = 0.707) under simulated AM 1.5 irradiation (100 mW/cm²).     

Synthesis and thermo-responsive behavior of fluorescent labeled microgel particles based on poly(N-isopropylacrylamide) and its related polymers

Poly(N-isopropylacrylamide) (PNIPAM) microgel particles labeled with 3-(2-propenyl)-9-(4-N,N-dimethylaminophenyl)phenanthrene (VDP) as an intramolecular fluorescent probe were prepared by emulsion polymerization. The thermo-responsive behavior of the VDP-labeled PNIPAM microgel particles dispersed in water was studied by turbidimetric and fluorescence analyses. The transition temperature of the VDP-labeled PNIPAM microgel particles in water determined by turbidimetric analysis was ca. 32.5 °C. The wavelength at the maximum fluorescence intensity of the VDP units linked directly to the microgel particles dramatically blue-shifted around the transition temperature. In addition it gradually blue-shifted even below the transition temperature where there was no change observed in the turbidity. These findings suggest that the gradual shrinking of microgel particles occurs with increasing temperature and the subsequent dramatic shrinking results in the increasing in the turbidity. The transition temperatures of VDP-labeled poly(N-n-propylacrylamide) and poly(N-isopropylmethacrylamide) microgel particles determined by turbidimetric analysis were ca. 23 and ca. 42.5 °C, respectively, and their thermo-responsive behavior was similar to that for the VDP-labeled PNIPAM system. In these three systems the microenvironments around the fluorescent probes above the transition temperatures became more hydrophobic than those below the transition temperature, and the estimated values of microenvionmental polarity around the VDP units on their collapsed states were almost the same.     

High optical transparency, low dielectric constant and light color of novel organosoluble polyamides with bulky alicyclic pendent group

Novel optically transparent, low dielectric and highly organosoluble alicyclic polyamides derived from bulky alicyclic diamine containing trifluoromethyl group on either side, 1,1-bis[4-(2-trifluoromethyl-4-aminophenoxy)phenyl]-4-tert-butylcyclohexane (BTFAPBC), were prepared. The polyamides were obtained in almost quantitative yields and showed inherent viscosity values between 0.55 and 0.72 dL g⁻¹ in DMAc solution. Most of the polyamides showed excellent solubility in polar solvents such as N-methyl-2-pyrrolidinone (NMP), N,N′-dimethyl acetamide (DMAc), N,N′-dimethyl formamide (DMF), pyridine, cyclohexanone, γ-butyrolactone and chloroform. The cut-off wavelength for polyamides ranged from 350 to 388 nm. Polyamides with alicyclic tert-butylcyclohexyl cardo and trifluoromethyl substituents exhibited low dielectric constants ranging from 3.29 to 3.98 (at 100 Hz) compared with commercially available polyamides [Amodel^®, 4.2-5.7 at 100 Hz]. Polyamides showed glass transition temperatures in the range of 244-266 °C and possessed a coefficient of thermal expansion (CTE) of 60-75 ppm °C⁻¹. Thermogravimetric analysis data showed that the polyamides were stable up to 430 °C and the 10% weight loss temperature was found to be in the range of 437-466 °C in nitrogen atmosphere. The polyamide films had a tensile strength in the range of 66-103 MPa, elongation at break in the range of 5-8%, and tensile modulus in the range of 1.5-2.2 GPa. Due to their properties, the polyamides could be considered as engineering plastic and photoelectric materials.     

Super porous organic-inorganic poly(N-isopropylacrylamide)-based hydrogel with a very fast temperature response

Porous organic-inorganic (O-I) hydrogels showing a very fast temperature response, including very fast reswelling were prepared: only 6 s are needed for 72% deswelling (gel collapse) as well as for 72% reswelling. Both deswelling and reswelling are practically complete in 14 s. The gels were prepared from N-isopropylacrylamide (NIPA), N,N′-methylenebisacrylamide (BAA) and tetramethoxysilane (TMOS) by simultaneous radical polymerization and hydrolytic polycondensation of TMOS. The syntheses were carried out at temperatures below the lower critical solution temperature (LCST) of poly(NIPA) in two steps: during the first stage the temperature was held at T = +15 °C and during the second the temperature was lowered below the freezing point of the reaction mixture, T = −18 °C. The ice crystals, which grew during the second stage, served as the pore-forming agent. The best samples were obtained if the second stage was started shortly before the gel point of the reaction mixture. The introduction of the inorganic phase (silica) is necessary for the ability of fast reswelling and also results in a strong improvement of the hydrogels' mechanical properties, while the maximum swelling degree remains nearly unaffected.     

Functional bioengineering copolymers. II. Synthesis and characterization of amphiphilic poly(N-isopropyl acrylamide-co-maleic anhydride) and its macrobranched derivatives

Radical-initiated copolymerization of N-isopropyl acrylamide (NIPA) with maleic anhydride (MA) and macromolecular reactions of synthesized poly(NIPA-co-MA) with polyethyleneglycol (PEG with a methoxy chain end and molecular weight of 2000 g mol⁻¹) and polyethyleneimine (PEI with molecular weight of 2000 g mol⁻¹) have been studied as a way to obtain new reactive amphiphilic water-soluble polymers potentially useful as carriers for gene delivery. Structure, composition and thermal behaviour of synthesized copolymers and their macrobranched architectures are determined by FTIR, ¹H and ¹³C NMR spectroscopy, elemental (N content) and chemical (acid number) analysis and differential scanning calorimetry, differential thermal and thermal gravimetric methods. It is shown that synthesized copolymers with given composition have low critical solution temperature (LCST) in the range of 30.2-46.4 °C at pH values of 4.0-7.4, which suggest the possibility of their biomedical applications.     

Rapid swelling and deswelling of thermoreversible hydrophobically modified poly(N-isopropylacrylamide) hydrogels prepared by freezing polymerisation

Rapid response thermally sensitive hydrophobically modified poly(N-isopropylacrylamide) hydrogels have been synthesised successfully using a two-step polymerisation method, the initial polymerisation being carried out at 20 °C, followed by polymerisation at −28 °C for 24 h. The results show that the swelling/deswelling rates of poly[N-isopropylacrylamide-co-(di-n-propylacrylamide)] P(NIPA-co-DPAM) hydrogels prepared by two-step polymerisation are much faster than for the same type of hydrogels prepared via conventional methods (30 °C for 24 h), i.e. the time for the former xerogel to absorb 70 and 90 wt% is just 30 and 240 min, respectively, compared to the latter xerogel which takes 1600 and 2500 min to absorb the same amounts of water. During deswelling (shrinking), the hydrogel loses 95 wt% water in 1 min, compared to a timescale for the corresponding cross-linked copolymers prepared by conventional methods of about 5 h for 50 wt% water loss. Scanning electron microscopy, and flotation experiments together with swelling ratio studies reveal that the polymeric network of the former hydrogel is characterised by an open structure with more pores and higher swelling ratio but lower mechanical strength compared to the latter hydrogels. Such rapid response hydrogels have potential applications in separation and drug release technologies for example.     

Dependence of shrinking kinetics of poly(N-isopropylacrylamide) gels on preparation temperature

Preparation temperature dependence of equilibrium swelling degree and shrinking kinetics of poly(N-isopropylacrylamide) gel has been investigated by optical microscopic measurements. The degree of swelling, d/d₀, at 20 °C was found to be strongly dependent on the preparation temperature, T_prep, where d and d₀ are the diameter of gel during observation and preparation, respectively. The value of d/d₀ was about 1.2 for T_prep=20 °C, but steeply increased by approaching the phase separation temperature ≈32.0 °C. Above 32.0 °C, d/d₀ decreases stepwise to 1.46. This upturn in d/d₀ was correlated with spatial inhomogeneities in gels. That is, the gel became opaque by increasing T_prep. Though the shrinking half-time, t_1/2, of gel was on the order of 500 min for T_prep≤20 °C, t_1/2 decreased to 2 min for T_prep≥26 °C. Hence, a rapid shrinking was attained by simply increasing T_prep. The physical implication of this rapid shrinking in gels was discussed in conjunction with the gel inhomogeneities and a thermodynamic theory of swelling equilibrium.     

Thermoreversible swelling behaviour of hydrogels based on N-isopropylacrylamide with a hydrophobic comonomer

Hydrogels were prepared by free radical polymerisation in aqueous solution of N-isopropylacrylamide (NIPA) and of NIPA with di-n-propylacrylamide (DPAM), di-n-octylacrylamide (DOAM) or di-dodecylacrylamide (DDAM) as hydrophobic comonomer. N,N-methylene bisacrylamide (BIS) and glyoxal bis(diallyacetal) (GLY) were used as crosslinkers. A series of copolymers with three different comonomer contents was synthesised and for some polymers three different crosslinker concentrations were employed. The swelling equilibrium of these hydrogels was studied as a function of temperature, hydrophobic comonomer species and content in aqueous solutions of the anionic surfactant sodium dodecyl sulfate (SDS). In pure water the gels showed a discontinuous volume phase transition at 33 and 30 °C for PNIPA and hydrophobically modified PNIPA copolymeric hydrogels, respectively. The swelling ratio r and the transition temperature (LCST) increased at low temperatures with the addition of SDS, this is ascribed to the conversion of non-ionic PNIPA gels into polyelectrolyte gels through the binding of SDS. At SDS concentration below 0.5 wt%, gels exhibited a single discontinuous volume transition at 36-38 °C. However, for SDS concentration above 0.5 wt%, two discontinuous volume transitions at 36-40 and 70 °C were observed. Additionally, the replacement of BIS by the novel octafunctional crosslinker glyoxal bis(diallylacetal) (GLY) yielded an increase in the swelling ratio.     

Micellization and phase transition behavior of thermosensitive poly(N-isopropylacrylamide)-poly(?-caprolactone)-poly(N-isopropylacrylamide) triblock copolymers

Thermosensitive triblock copolymers with two hydrophilic poly(N-isopropylacrylamide) blocks flanking a central hydrophobic poly(?-caprolactone) block were synthesized by atom transfer radical polymerization. Core-shell micellization of the triblock copolymers was inferred from the ¹H NMR spectra derived in two different solvent environments (CDCl₃ and D₂O). The micellar characteristics of these amphiphilic triblock copolymers were studied by pyrene fluorescence techniques, dynamic light scattering and transmission electron microscopy. The critical micelle concentrations of the triblock copolymers were in the range of 4-16 mg/L and the partition coefficients were in the range of 3.10 × 10⁴ to 2.46 × 10⁵. The mean diameters of the micelles, measured by light scattering, were between 90 and 120 nm. The temperature sensitivity of the triblock copolymers was demonstrated by the phase transition of a 250 mg/L aqueous polymer solution at the lower critical solution temperature (LCST). The enthalpy of the phase transition was determined by differential scanning calorimetry. PM3 quantum mechanical calculation method was used to understand the intermolecular interactions between the copolymer and the water molecules. A modular approach was used to simulate the phase transition observed at the LCST.     

High glass transition and thermal stability of new pyridine-containing polyimides: Effect of protonation on fluorescence

A new diamine monomer containing heterocyclic pyridine and triphenylamine groups, 4-(4,4′-diaminotriphenylamine)-2,6-bis(4-methylphenyl)pyridine (4), was synthesized by Chichibabin and nucleophilic fluoro-displacement reactions. The diamine was used to prepare a series of novel polyimides via polycondensation with various aromatic tetracarboxylic dianhydrides in N-methyl-2-pyrrolidinone. The polyimide 4a derived from the diamine 4 with 4,4′-hexafluoroisopropylidenediphthalic anhydride and having high T_g (313 °C), mechanical, and thermal properties was soluble in various organic solvents, such as N-methyl-2-pyrrolidinone, N,N-dimethylacetamide, N,N-dimethylformamide, pyridine, chloroform, tetrahydrofuran, at room temperature. The polyimide (4a) could be cast into a self-standing film from DMAc solution and was thermally converted into tough and flexible film. The film had high tensile modulus of 2.2 GPa and exhibited excellent thermal stability in both nitrogen and air (T_d¹⁰ > 550 °C). The pristine polymer exhibited the UV-vis absorption bands in the region 240-400 nm and protonated polymer exhibited absorption in the region 390-500 nm. The protonated polymer possessed strong orange fluorescence (around 600 nm) in THF solution after protonation with acids as excited at 438 nm. The fluorescent intensity was influenced by the acid concentrations and the chemical structure of conjugated bases. The fluorescent intensity at 600 nm increased as acid concentration from a lower to a moderate concentration and decreased at higher concentrations.     

Hydrogen-bond-assisted isotactic-specific radical polymerization of N-isopropylacrylamide with pyridine N-oxide

Radical polymerization of N-isopropylacrylamide (NIPAAm) in CHCl₃ at low temperatures in the presence of pyridine N-oxide (PNO) was investigated. An isotactic poly(NIPAAm) with meso diad content of 61% was successfully prepared at −60 °C in the presence of a two-fold amount of PNO. Thermodynamic analysis suggested that the isotactic-specificity was entropically induced, probably due to conformational fixation near the propagating chain-end through coordination by PNO.     

Synthesis of a soluble conjugated copolymer based on dialkyl-substituted dithienothiophene and its application in photovoltaic cells

A soluble conjugated alternating 3,5-didecanyldithieno[3,2-b:2′,3′-d]thiophene-thiophene copolymer was synthesized by palladium(0)-catalyzed Stille coupling reaction. The thermal, absorption, emission, electrochemical, and photovoltaic properties of the polymer were examined. A weight-average molecular weight around 6.2 × 10⁴ and a polydispersity index of 1.8 was estimated for the polymer using gel permeation chromatography. The polymer exhibits good thermal stability with decomposition temperature of 340 °C and glass-transition temperature of 136 °C. The polymer shows strong absorption peaked at 505 nm in diluted solution and 518 nm in thin film with an optical band gap 2.0 eV. The polymer exhibits intense emission located at 550 nm in solution and 603 nm in film. The HOMO and LUMO energies of the polymer were estimated to be −5.4 and −3.4 eV, respectively, by cyclic voltammetry. Polymer solar cells were fabricated based on the blend of the polymer and methanofullerene [6,6]-phenyl C61-butyric acid methyl ester (PCBM). The power conversion efficiency of 0.7% was achieved under AM 1.5, 100 mW/cm² using polymer:PCBM (1:4, w/w) as active layer.     

Preparation of hydrogel nanoparticles by atom transfer radical polymerization of N-isopropylacrylamide in aqueous media using PEG macro-initiator

PEG-b-PNIPAM block copolymers are synthesized by the atom transfer radical polymerization of NIPAM using PEG macro-initiator. When the polymerization temperature is 25 °C, the block copolymer is soluble in water, whereas the block copolymer is phase-separated to form micelles during polymerization as the polymerization temperature is raised to 50 °C, the temperature above the LCST of PEG-b-PNIPAM. To prepare stable hydrogel nanoparticles in water at room temperature, a small amount of N,N′-ethylenebisacrylamide is added as a cross-linker to the reaction system, where the size of nanoparticles is controlled by the composition of mixed solvent.