Solid‐state mechanical properties of polypropylene/nylon 6/clay nanocomposites

The mechanical and thermomechanical properties as well as microstructures of polypropylene/nylon 6/clay nanocomposites prepared by varying the loading of PP‐MA compatibilizer and organoclay (OMMT) were investigated. The compatibilizer PP‐MA was used to improve the adhesion between the phases of polymers and the dispersion of OMMT in polymer matrix. Improvement of interfacial adhesion between the PP and PA6 phases occurred after the addition of PP‐MA as confirmed by SEM micrographs. Moreover, as shown by the DSC thermograms and XRD results, the degree of crystallinity of PA6 decreased in the presence of PP‐MA. The presence of OMMT increased the tensile modulus as a function of OMMT loading due to the good dispersion of OMMT in the matrix. The insertion of polymer chains between clay platelets was verified by both XRD and TEM techniques. The viscosity of the nanocomposites decreased as PP‐MA loading increased due to the change in sizes of PA6 dispersed phase, and the viscosity increased as OMMT loading increased due to the interaction between the clay platelets and polymer chains. The clay platelets were located at the interface between PP and PA6 as confirmed by both SEM and TEM. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

尼龙6/粘土纳米复合材料的性能

对尼龙6/粘土纳米复合材料(PA6CN)的力学性能、结晶性能、流变性能、热稳定性、阻隔性能、阻燃性能、各向异性和可纺性进行了综述。加入粘土后,基体尼龙6的晶型变为γ型,改善了尼龙6的力学性能,提高了热变形温度,降低了吸水率,改善了气体阻隔性和材料的阻燃性,拓宽了复合材料的应用范围。     

Modeling properties of nylon 6/clay nanocomposites using composite theories

The reinforcement of nylon 6 by layered aluminosilicates (LAS) and glass fibers was examined using the composite theories of Halpin-Tsai and Mori-Tanaka. Theoretical comparisons show that exfoliated LAS offer superior reinforcement to glass fibers owing to the filler's high modulus, high aspect ratio, and its ability to reinforce in two directions. The effect of incomplete exfoliation of simple stacks of LAS on nanocomposite modulus was also examined. Increasing the number of platelets per stack and the gallery spacing between platelets results in a dramatic decrease in reinforcing efficiency. The predictions were benchmarked against experimental data for nylon 6 nanocomposites based on organically modified montmorillonite and glass fibers. The quantitative determination of the morphology of the nanocomposites is non-trivial due to the large distribution of filler shapes and sizes present. Thus, a detailed experimental procedure for determining the aspect ratio of the nanocomposites is reported. The composite theories satisfactorily capture the stiffness behavior of both types of composites. Furthermore, experimental heat distortion temperatures and those predicted from modeling the dynamic mechanical properties of nanocomposites are in reasonable agreement.     

Measuring the extent of exfoliation in polymer/clay nanocomposites using real-time process monitoring methods

Dielectric and optical transmission measurements obtained during processing of polymer/clay composites yielded quantitative information about the extent of clay exfoliation in the polymer matrix. Measurements were made using an instrumented slit die that was situated at the exit of a twin screw extruder. Nylon 6, 11 and 12 resins were compounded with several organo modified montmorillonite clays. Dielectric and optical data were correlated with off-line transmission electron microscopy. Dielectric observations revealed a large Maxwell-Wagner (MW) relaxation whose characteristic frequency reflects an RC time constant associated with the conduction of ions and the polarization of the resin/clay interface. Optical transmission measurements showed that transmission increased with increasing extent of exfoliation because light scattering due to aggregate clay particles is reduced as the particles exfoliate nanosize silicate flakes. Extent of exfoliation models, based on MW relaxation time and its relationship to interfacial polarization, and based on optical transmission measurements, are developed.     

The thermal conductivity of Nylon 6/clay nanocomposites

Nylon 6/clay nanocomposites (NCNs) of different clay loadings are prepared by melt compounding. The effects of clay loading and dispersion on the thermal conductivity of NCNs are investigated using XRD, TEM, DSC, and POM. The results show that the thermal conductivity of the exfoliated NCNs decreases with an increase of clay content; but the thermal conductivity of the intercalated NCNs does not decrease, indeed, it increase markedly at high clay content. Such results observed in the exfoliated NCNs are opposite to the expectation of the classic Maxwell thermal conduction model. The further investigations indicate that such decrease observed in the exfoliated NCNs is due mainly to the exfoliation of clay layers. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Micro- and nano-structure in polypropylene/clay nanocomposites

Polypropylene (PP)/clay nanocomposites prepared by melt blending using different clays and coupling agents based on maleic anhydride-grafted PP (MA-PP) were studied. Clay dispersion using field emission gun scanning electron microscope (FEG-SEM) and transmission electron microscopy (TEM), and PP matrix morphology were characterized. Clay dispersion was improved in the presence of MA-PP, as shown by the higher particles surface density (number of particles/mm²) at all micro-, sub-micro- and nano-levels. The PP spherulite diameter was affected by both the presence of MA-PP and clay dispersion. Clay intercalation, characterized by both complementary X-ray diffraction (XRD) and TEM, was greatly influenced by the characteristics of MA-PP. The use of low molecular weight (M_w) MA-PP led to a good and uniform intercalation but with no further possibility to exfoliation. The use of higher M_w MA-PP led to a heterogeneous intercalation with signs of exfoliation. The crystallization behavior of nanocomposites was studied by differential scanning calorimetry (DSC). When fine clay dispersion was achieved with MA-PP, clay-nucleating effect was limited and lower crystallization temperature and rates were observed. It was also shown by wide angle X-ray diffraction (WAXD) that clay induced some orientation of α-phase PP crystallites.     

Calculating barrier properties of polymer/clay nanocomposites: Effects of clay layers

We analyzed the effects of clay layers on the barrier properties of polymer/clay nanocomposites containing impermeable and oriented clay layers. Using the relative permeability theory in combination with the detour theory, we obtained new relative permeability expressions that allow us to investigate the relative permeability R_p as a function of lateral separation b, layer thickness w, gallery height H, layer length L, and layer volume fraction Φ_s. It was found that intercalated and/or incomplete exfoliated structures and dispersed tactoids with several layers can effectively enhance the barrier properties of the materials. Furthermore, we developed the chain-segment immobility factor to briefly discuss the chain confinement from clay layers. The results showed that the chain confinement enhanced the barrier properties of the intercalated nanocomposites. Our model is better consistent with the experiments when Φ_s>0.01. The findings provide guidelines for tailoring clay layer length, volume fraction and dispersion for fabricating polymer-clay nanocomposite with the unique barrier properties.     

Morphology and melt rheology of nylon 11/clay nanocomposites

Nylon 11 (PA11)/clay nanocomposites have been prepared by melt‐blending, followed by melt‐extrusion through a capillary. Transmission electron microscopy shows that the exfoliated clay morphology is dominant for low nanofiller content, while the intercalated one is prevailing for high filler loading. Melt rheological properties of PA11 nanocomposites have been studied in both linear and nonlinear viscoelastic response regions. In the linear regime, the nanocomposites exhibit much higher storage modulus (G′) and loss modulus (G″) values than neat PA11. The values of G′ and G″ increase steadily with clay loading at low concentrations, while the G′ and G″ for the sample with 5 wt % clay show an inverse dependence and lie between the modulus values of the samples with 1 and 2 wt % of clay. This is attributed to the alignment/orientation of nanoclay platelets in the intercalated nanocomposite induced by capillary extrusion. In the nonlinear regime, the nanocomposites show increased shear viscosities when compared with the neat resin. The dependence of the shear viscosity on clay loading has analogous trend to that of G′ and G″. Finally, a comparison has been made between the complex and steady viscosities to verify the applicability of the empirical Cox‐Merz rule. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 542–549, 2006     

Preparation and properties of nylon 6/carboxylic silica nanocomposites via in situ polymerization

Nylon 6/carboxylic acid‐functionalized silica nanoparticles (SiO₂‐COOH) nanocomposites were prepared by in situ polymerization of caprolactam in the presence of SiO₂‐COOH. The aim of this work was to study the effect of carboxylic silica on the properties of the nylon 6 through the interfacial interactions between the SiO₂‐COOH nanoparticles and the nylon 6 matrix. For comparison, pure nylon 6, nylon 6/SiO₂ (unmodified) and nylon 6/amino‐functionalized SiO₂ (SiO₂‐NH₂) were also prepared via the same method. Fourier transform infrared spectrometer (FTIR) spectroscopy was used to evaluate the structure of SiO₂‐COOH and nylon 6/SiO₂‐COOH. The results from thermal gravimetric analysis (TGA) indicated that decomposition temperatures of nylon 6/SiO₂‐COOH nanocomposites at the 5 wt % of the total weight loss were higher than the pure nylon 6. Differential scanning calorimeter (DSC) studies showed that the melting point (T_m) and degree of crystallinity (X_c) of nylon 6/SiO₂‐COOH were lower than the pure nylon 6. Mechanical properties results of the nanocomposites showed that nylon 6 with incorporation of SiO₂‐COOH had better mechanical properties than that of pure nylon 6, nylon 6/SiO₂, and nylon 6/SiO₂‐NH₂. The morphology of SiO₂, SiO₂‐NH₂, and SiO₂‐COOH nanoparticles in nylon 6 matrix was observed using SEM measurements. The results revealed that the dispersion of SiO₂‐COOH nanoparticles in nylon 6 matrix was better than SiO₂ and SiO₂‐NH₂ nanoparticles. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polymerization kinetics and thermal properties of dicyanate/clay nanocomposites

The polymerization kinetics and thermal properties of dicyanate/clay nanocomposites were investigated. A type of organically modified clay was used as nanometer‐size fillers for the thermosetting dicyanate resin. Differential scanning calorimetry (DSC) was used to study the curing behavior of the dicyanate/clay nanocomposite systems. The polymerization rate of the nanocomposite systems increased with increasing clay content. An autocatalytic reaction mechanism could adequately describe the polymerization kinetics of the dicyanate/clay nanocomposite systems. The polymerization kinetic parameters were determined by fitting the DSC conversion data to the proposed kinetic equation. The glass‐transition temperature of the dicyanate/clay nanocomposites increased with increasing clay content. The thermal decomposition behavior of the dicyanate/clay nanocomposites was investigated by thermogravimetric analysis. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1955–1960, 2004     

Synthesis and characterization of nylon 6/clay nanocomposites prepared by ultrasonication and in situ polymerization

Nylon 6 nanocomposites were prepared by the in situ polymerization of ε‐caprolactam with ultrasonically dispersed organically modified montmorillonite clay (Cloisite 30B®). Dispersions of the clay platelets with concentrations in the range 1–5 wt % in the monomer were characterized using rheological measurements. All mixtures exhibited shear‐thinning, signifying that the clay particles were dispersed as platelets and forming a “house of cards” structure. Samples with Cloisite concentrations above 2 wt % showed a drop in viscosity between the initial shearing and repeated shearing, indicative of shearing breaking down the initial “house of cards” structures formed on sonication. DMTA measurements of the samples showed an increase in the β‐relaxation temperature with increasing clay concentration. The bending modulus, at temperatures below T_g, showed an increase with increasing clay concentration up to 4 wt %. X‐ray diffraction measurements showed that all nylon 6/Cloisite 30B samples were exfoliated apart from the 5 wt %, which showed that some intercalated material was present. The nylon crystallized into the α‐crystalline phase, which is the most thermodynamically stable form. Preference for this form may be a consequence of the long time associated with the postcondensation step in the synthesis or the influence of the platelets on the nucleation step of the crystal growth. DSC measurements showed a retardation of the crystallization rate of nanocomposite samples when compared with that of pure nylon 6, due to the exfoliated clay platelets hindering chain movement. This behavior is different from that observed for the melt‐mixed nylon 6/clay nanocomposites, which show an enhancement in the crystallization rate. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of clay on properties of polyimide‐clay nanocomposites

Effect of clay on mechanical, thermal, moisture absorption, and dielectric properties of polyimide‐clay nanocomposites was investigated. Nanocomposites of polyimide (ODA‐BSAA) hybridized with two modified clay (PK‐802 and PK‐805) were synthesized for comparison. The silicate layers in the polymer matrix were intercalated/exfoliated as confirmed by wide‐angle X‐ray diffraction and transmission electron microscopy. Thermal stability, moisture absorption, and storage modulus for these nanocomposites are improved as hybridized clay increases. Reduced dielectric constants due to the hybridization of layered silicates are observed at frequencies of 1 kHz–1 MHz and temperatures of 35–150°C. The tetrahedrally substituted smectite (PK‐805) resulted in higher mechanical strength and dielectric constants than those of octahedrally substituted smectite (PK‐802), which could be attributed to their stronger ionic bonding between clay layer and polymer matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 318–324, 2007     

Structural hierarchy developed in injection molding of nylon 6/clay/carbon black nanocomposites

The influence of platelet-type clay nanoparticle (nanoplatelet) on the structural evolution in injection-molded nylon 6)/carbon composites was investigated. In the absence of nanoplatelets, the nylon 6/CB systems were found to exhibit unoriented structure with nylon 6 crystalline regions exhibiting exclusively α crystal form throughout the thickness of the samples. However, inclusion of nanoplatelets induces substantial local orientation of the nylon 6 chains in the molded parts in all processing conditions and compositions. In these clay/nylon 6/CB ternary nano systems, nylon 6 matrix was found to be exclusively in γ crystal form at the skin regions and α crystal form fraction increases towards the core of the molded parts as a result of decrease in cooling rate with depth during the solidification stage. Two nanoplatelet orientation behaviors were identified: (i) in the absence of irregular shaped CB, the nanoplatelets align parallel with one another following the local flow patterns. The latter behavior also causes enhanced orientation of the nylon 6 chains undergoing substantial shear amplification trapped in between the nanoplatelets (ii) in the CB-enriched regions, nanoplatelets though still remaining parallel to one another, are randomized by following the local contours of irregular shaped CB aggregates. These CB aggregates themselves were found to organize to form trains in larger scale as a result of flow alignment.     

Mechanical properties and structures of dicyanate–clay nanocomposites

Dicyanate–clay nanocomposites comprising a dicyanate resin and a type of organically modified clay were prepared and characterized, and their thermomechanical properties were investigated. The organically modified clay had silicate layers of nanometer size intercalated with an organic modifier, which improved the compatibility between the clay and organic materials, such as dicyanate resins. Dynamic mechanical analysis was performed to investigate the thermomechanical properties of the dicyanate–clay nanocomposites containing various amounts of the clay. The storage modulus of the nanocomposites below their glass‐transition temperatures slightly increased with increasing clay content. The glass‐transition temperature of the dicyanate–clay nanocomposites increased with increasing clay content. The nanostructures of the dicyanate–clay nanocomposites were characterized by transmission electron microscopy and X‐ray diffraction analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2629–2633, 2003     

Effect of sample thickness on the mechanical properties of injection-molded polyamide-6 and polyamide-6 clay nanocomposites

The effect of the thickness on the mechanical properties of injection-molded specimens of pure polyamide-6 (PA6) and polyamide-6 clay nanocomposites (PA6-NC) with 5 wt% of layered silicates was investigated. Plates of 0.5, 0.75, 1 and 2 mm thickness were characterized in the injection direction using Dynamic Mechanical Analysis under torsion and tension respectively, and tensile tests. The fracture surfaces were analyzed by Scanning Electron Microscopy. In contrast with PA6, PA6-NC showed thickness effect and clear differences in the mechanical and thermomechanical properties between skin and core, especially in the 2 mm thick samples. Increasing thickness in PA6-NC led to a reduction of tensile modulus and yield stress. In the fracture surface of the thicker tensile specimens the formation of a sheet-like structure was observed. Multiple voiding in the core causing initial failure in this region and a stiffer skin with a better orientation of the layered silicates in the injection direction are two important elements of a micromechanical model proposed in this paper to explain the fracture mechanism in PA6-NC.     

Effects of swelling agents on the crystallization behavior and mechanical properties of polyamide 6/clay nanocomposites

Montomorillonite was organically modified with three different swelling agents: n‐dodecylamine, 12‐aminolauric acid, and 1,12‐diaminodecane. These organoclays and polyamide 6 (PA6) were blended in a formic acid solution. X‐ray diffraction analysis showed that the clay still retained its layer structure in the PA6/clay nanocomposite. Consequently, these materials were intercalated nanocomposites. The effects of the swelling agent and organoclay content on the crystallization behavior of the PA6/clay nanocomposites were studied with differential scanning calorimetry. The results showed that the position and width of the exothermic peak of the PA6/clay nanocomposites were changed during the nonisothermal crystallization process. The clay behaved as a nucleating agent and enhanced the crystallization rate of PA6.The crystallinity of PA6 decreased with an increasing clay content. Different swelling agents also affected the crystallization behavior of PA6. The effects of the type and content of the swelling agent on the tensile and flexural properties of PA6/clay nanocomposites were also investigated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1686–1693, 2003     

Mechanical properties of polypropylene/clay nanocomposites: Effect of clay content,polymer/clay compatibility,and processing conditions

In this work, polypropylene/clay nanocomposites with 0.5, 1, 3, and 5 wt % of montmorillonite (MMT) (unmodified clay) were prepared by intensive mixing at 50 rpm and 10 min of mixing. For the highest clay content (5 wt %), the initial materials or the processing conditions were changed to study their independent effect. On one hand, 10 wt % of PP‐graft‐MA (PP‐g‐MA) was incorporated or MMT was replaced by organomodified clays (C10A and C30B). On the other side, for the initial system, the speed of rotation (100 and 150 rpm) and the mixing time (5 and 15 min) were altered. In all cases, the state of the clay inside the matrix (DRX), the degree of dispersion in the micro (SEM) and nano (TEM) scales, and the rheological and mechanical properties were analyzed. It was found that the stiffness increased with clay content, whereas tensile and impact strength did not significantly change. Although intercalated structures were observed in the composites with unmodified clay, in the composites with modified clay or PP‐g‐MA, improved dispersion of clay in PP was found. The mechanical properties increased accordingly. The degree of dispersion of the filler in the matrix appeared to be unaffected by the changes in the processing conditions introduced. Finally, the elastic modulus was modeled by using an effective filler‐parameter model based on Halpin–Tsai equations, which also allowed estimating the relative degree of dispersion. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Alteration of the mechanical and thermal properties of nylon 6/nylon 6,6 blends by nanoclay

Nylon 6 [N(6)], nylon 6,6 [N(6,6)], and their blends at different clay loadings were prepared. The mix was melted and injected into strip‐shaped samples. Mechanical and thermal analyses were performed to investigate the effect of blending and the incorporated clay on the mechanical and thermal properties. Enhancements in the Young's modulus and hardness were obtained for all of the nanocomposites, with a 55% increase in Young's modulus after the addition of 6 wt % nanoclay, although the improvement in tensile strength depended on the blend ratio, with greatest effects on the 50% N(6)/50% N(6,6) blend with increases of 44 and 59% for 2 and 4% clay loadings, respectively. Thermogravimetric analysis showed an enhancement in the thermal properties in the 50% N(6)/50% N(6,6) blend at 2% clay loading, and the blend exhibited ductile behavior at this loading. Increases in the crystallization peak temperatures of 10–15° in N(6,6) and the two blends 30% N(6)/70% N(6,6) and 50% N(6)/50% N(6,6) were observed after the addition of the clay. The nanoclay enhanced the γ‐/β‐form crystals in N(6) and N(6,6) neat polymers and also in the blends. Fourier transform infrared spectroscopy FT‐IR revealed the formation of hydrogen bonding and the possible formation of ionic bonds between the polymers and the nanoclay, which resulted in enhancements in the mechanical properties of the blends. The distribution of the nanoclay in the blend was well dispersed, as shown by X‐ray diffraction analysis. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Dielectric and electromagnetic interference shielding properties of zeolite 13X and carbon black nanoparticles based PVDF nanocomposites

In the present work, Zeolite 13X and carbon black nanoparticles (CBNPs) reinforced polyvinylidene fluoride (PVDF) nanocomposites were obtained by a simple solvent casting technique. The structural, morphological and thermal properties of PVDF/Zeolite 13X/CBNPs nanocomposites with various loadings of Zeolite 13X and CBNPs were investigated using Fourier-transform infrared spectroscopy, X-ray diffraction, Scanning electron microscopy and thermo-gravimetric analysis. The dielectric studies were carried out in the 50 Hz–10 MHz frequency range at room temperature. The electromagnetic interference (EMI) shielding effectiveness (SE) of PVDF/Zeolite 13X/CBNPs nanocomposite was investigated in the 8–18 GHz frequency region (X-band and Ku-band). The maximum EMI SE of approximately −11.1 dB (8–12 GHz) and −11.5 dB (12–18 GHz) was observed for PVDF/CBNPs nanocomposites with 10 wt% loading of CBNPs. These findings emphasize the application of PVDF/Zeolite 13X/CBNPs nanocomposites as a potential EMI shielding material.     

Effect of amine-terminated butadiene-acrylonitrile/clay combinations on the structure and properties of epoxy nanocomposites

The effect of the clay content and the method of its combination with amine-terminated butadiene-acrylonitrile (ATBN) on the structure and behavior of epoxy was studied. In the case of the simultaneous addition of both components, the increasing clay content had a very small effect on the size of the reaction-induced phase separation-formed particles at 5% rubber content due to predominant elimination of two major clay effects, i.e., the nucleation due to phase separation and the kinetics. As a result, both the time window between the onset of phase separation and vitrification and the viscosity at the cloud point did not change significantly. The minor change in the particle size/clay content dependences with different curing temperatures indicates that the balance between the two clay effects shifted. The corresponding study of the mechanical behavior indicated that the best balanced mechanical properties were obtained at certain clay/ATBN ratios, and thus, there was synergy between the components. Similar mechanical parameters were obtained for the application of both components in the form of ATBN/montmorillonite intercalate. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012