Plastic deformation and damage of polyoxymethylene in the large strain range at elevated temperatures

The deformation behaviour of polyoxymethylene has been studied in plane strain compression at temperatures from 120 °C up to 165 °C and in uniaxial tension and simple shear at 160 °C for strain rates from 10⁻⁴ to 1 s⁻¹. In uniaxial tension the stress-strain behaviour was determined by a novel video-controlled testing system. The measurements showed that there was a very significant evolution of volumetric strain, indicating that damage mechanisms play a key role in the plastic deformation behaviour.All tests showed similar deformation stages with a short region of visco-elastic behaviour followed by a rounded yield point. The von Mises equivalent yield stress for these tests showed a linear relationship with logarithmic strain rate, suggestive of an Eyring type thermally activated process. After yielding, all stress-strain curves showed a long plastic deformation regime, which in shear occurred at constant stress. In plane strain compression there was also only a very small increase in stress, in contrast to uniaxial tension where very significant strain hardening was observed at high strains, which is attributed to the onset of structural changes.     

Preparation of brush-like crystals of poly[2,6-(1,4-phenylene)-benzobisimidazole]

Poly[2,6-(1,4-phenylene)-benzobisimidazole] (PPBI) crystals were prepared by using reaction-induced crystallization of oligomers during solution polymerization of 1,2,4,5-tetraaminobenzene and diphenyl terephthalate. Polymerizations were carried out at a monomer concentration of 4.3 × 10⁻² mol L⁻¹ at 350 °C for 6 h. Brush-like PPBI crystals were obtained in a mixture of structural isomers of dibenzyltoluene, in which many needle-like crystals came out vertically from the surface of the ribbon-like crystals. Average width and thickness of the ribbon-like crystals were 0.75 μm and 0.11 μm, respectively. And average length and diameter of the needle-like crystals were 0.36 μm and 50 nm, respectively. The brush-like crystals possessed high crystallinity and exhibited good thermal resistance. The ribbon-like crystals were formed by the crystallization of imidazole oligomers at an initial stage of polymerization, and then the needle-like crystals grew from the surface of the ribbon-like crystals. Polymerization occurred on the crystals when the oligomers were crystallized, leading to the high molecular weight PPBI crystals.     

The mechanical properties of poly(ether-ether-ketone) (PEEK) with emphasis on the large compressive strain response

The mechanical properties of PEEK 450G have been extensively investigated. The compressive properties were measured at strain rates between 1 × 10⁻⁴ and 3000 s⁻¹ and temperatures between −85 and 200 °C. The tensile properties were measured between the strain rates of 2.7 × 10⁻⁵ and 1.9 × 10⁻² s⁻¹ and at temperatures between −50 and 150 °C. The Taylor impact properties were investigated as a function of velocity and various large-strain compression tests were undertaken to explain the results. The fracture toughness was investigated as a function of temperature and compared with previous literature. Additionally, the fracture surfaces were studied by microscopy. As with all semi-crystalline polymers the mechanical response is a strong function of the strain rate and testing temperature. A previously reported phenomenon of darkening observed in Taylor impacted samples is shown to be due to reduced crystallinity brought about by large compressive strain. For samples deformed to large compressive strains using a variety of techniques and strain-rates the measured Vickers hardness was found to decrease in accordance with reduced crystallinity measured by other techniques.     

The spatial uniformity and electromechanical stability of transparent, conductive films of single walled nanotubes

We have prepared thin films of arc discharge single walled nanotubes by vacuum filtration. For film thicknesses greater than 40 nm, the films are of high optical quality; the optical transmission varies by <2% over the film area when measured with a spatial resolution of 4 μm. However, the films become spatially non-uniform for film thickness below 40 nm. The in-plane DC conductivity correlates with the uniformity, increasing from ∼3800 S/m for a 10 nm thick film to ∼2-2.5 × 10⁵ S/m for films of thickness >40 nm. Conductive atomic force microscopy maps show reasonably uniform current flow out of the plane of the film. For all thicknesses, the optical transmittance scales with film thickness as expected for a thin conducting film with optical conductivity of 1.7 × 10⁴ S/m (λ = 550 nm). For films with t > 40 nm the ratio of DC to optical conductivity was σ_DC/σ_Op = 13.0, leading to values of transmittance and sheet resistance such as T = 80% and R_s = 110 Ω/□ for the t = 40 nm film. Electromechanically, these films were very stable showing conductivity changes of <5% and <2% when cycled over 2000 times in compression and tension respectively.     

Cyclic viscoplasticity of solid polymers: The effects of strain rate and amplitude of deformation

Observations are reported on polypropylene random copolymer in uniaxial cyclic tensile tests with various strain rates (ranging from 1.7 × 10⁻⁴ to 8.3 × 10⁻³ s⁻¹). Each cycle of deformation involves tension up to the maximal strain ε_max (from 0.05 to 0.20) and retraction down to the zero stress. The study focuses on deformation programs with 10-50 cycles in each test. A constitutive model is derived for the viscoplastic behavior of a solid polymer at three-dimensional cyclic deformations with small strains. Material constants in the stress-strain relations are found by fitting the experimental data. Good agreement is demonstrated between the observations and the results of numerical simulation.     

Plastic membrane electrodes for the determination of flavoxate hydrochloride and cyclopentolate hydrochloride

Four novel ion-exchangers (Fx-Rt (I), Fx-TPB (II), Cp3-PMA (III) and Cp3-PTA (IV)) of antispasmodic and anticholinergic drugs, flavoxate hydrochloride (FxCl), 2-piperidinoethyl-3-methyl-4-oxo-2-phenyl-4h-1-benzopyran-8-carboxylate hydrochloride, cyclopentolate hydrochloride (CpCl) and (2-(dimethylamino)ethyl (RS)-(1-hydroxycyclopentyl)phenylacetate) hydrochloride were synthesized and incorporated into poly(vinyl chloride)-based membrane electrodes for the quantification of FxCl and CpCl in different pharmaceutical preparations. The influence of membrane composition on the potentiometric response of the membrane electrodes was found to substantially improve the performance characteristics. The best performance was reported with membranes having compositions (w/w) of Fx-Rt (2%):PVC (49%):DOP (49%), Fx-TPB (7%):PVC (46.5%):DOP (46.5%), Cp3-PMA (8%):PVC (46%):DOP (46%) and Cp3-PTA (9%):PVC (45.5%):DOP (45.5%). The proposed sensors exhibited Nernstian responses in the concentration ranges of 1.39 × 10⁻⁶-5.00 × 10⁻⁴, 9.90 × 10⁻⁷-3.75 × 10⁻⁵, 1.39 × 10⁻⁵-2.53 × 10⁻³ and 3.21 × 10⁻⁶-8.62 × 10⁻⁴ M, with detection limits of 5.50 × 10⁻⁷, 9.8 × 10⁻⁷, 9.8 × 10⁻⁶ and 2.95 × 10⁻⁶ M for the (I), (II), (III) and (IV) electrodes, respectively. The membrane electrodes performed satisfactorily over pH ranges of 2.0-5.5, 2.0-5.5, 2.0-5.0 and 2.0-7.5, with fast response times of 20, 30, 15 and 20 s for the (I), (II), (III) and (IV) electrodes, respectively. The practical utility of the sensors was demonstrated by the determination of FxCl and CpCl in pure solutions and pharmaceutical preparations using standard additions and potentiometric titration.     

The effects of thermomechanical history and strain rate on antiplasticization of PVC

Antiplasticization is mechanically characterized by an increase in the polymer stiffness and/or yield strength upon the incorporation of a small amount of a low-molecular weight diluent. It is attributed to hindrance of the local β-relaxation motions of the polymer. Here, we have studied the effects of thermal treatment, plastic deformation, and strain rate on the antiplasticization of the yield stress of a 95 wt% poly(vinyl chloride)/5 wt% dioctyl phthalate (PVC/5 wt% DOP) compound. Two thermal treatments were applied to the materials - cooling to room temperature from above T_g by a quench or by a slow oven-cool anneal. When compressed at low to moderate strain rates, antiplasticization was observed in the annealed (physically aged) PVC/5 wt% DOP but not in the quenched (unaged) PVC/5 wt% DOP. Load-unload-reload compression cycles revealed that antiplasticization can be erased by plastic strain; the anomalously high yield stress of PVC/5 wt% DOP observed in the first load cycle softens to a value lower than that of the neat PVC in subsequent cycles. The results indicate that disordered, high free volume microstructural states, obtained either from thermal quenching or from plastic straining, liberate the beta motions of the PVC molecule which, in turn, erase antiplasticization of the yield stress. Earlier work on the rate-dependence of yield has demonstrated that beta motions must be stress-activated in order to yield neat PVC when deformed at high strain rates (>100/s). Hence, we have characterized the rate-dependence of the antiplasticization of the yield stress by testing the annealed materials in uniaxial compression over a wide range of strain rates (10⁻⁴/s-3000/s). Antiplasticization was observed in PVC/5 wt% DOP in the low strain rate regime where beta motions are free in neat PVC but hindered in PVC/5 wt% DOP; however, the antiplasticization (elevation of yield stress) gradually diminished with increasing strain rate.     

Experimental characterisation and constitutive modelling of RTM-6 resin under impact loading

The response to mechanical loading of the thermosetting resin system RTM-6 has been investigated experimentally as a function of strain rate and a constitutive model has been applied to describe the observed and quantified material behaviour. In order to determine strain rate effects and to draw conclusions about the hydrostatic stress dependency of the material, specimens were tested in compression and tension at strain rates from 10⁻³ to 10⁴ s⁻¹. A Standard screw-driven tensile machine was used for quasi-static testing, with an ‘in house’ hydraulic rig and Hopkinson bars for medium and high strain rates, respectively. At all rates appropriate photography and optical metrology have been used for direct strain measurement, observation of failure and validation of experimental procedures. In order to enable the experimental characterisation of this brittle material at very high rates in tension, a novel pulse shaping technique has been applied. With the help of this device, strain rates of up to 3800 s⁻¹ have been achieved while maintaining homogeneous deformation state until specimen fracture in the gauge section of the tensile specimens. The yield stress and initial modulus increased with increasing strain rate for both compression and tension, while the strain to failure decreased with strain rate in tension. An existing constitutive model, the Goldberg model has been extended in order to take into account the nonlinear strain rate dependence of the elastic modulus. The model has been validated against 3-point impact bending tests of prismatic RTM-6 beams.     

Poly(phenylacetylene) with bulky chiral germyl groups: synthesis and effects of measuring solvents and temperature on chiroptical properties

(+)-p-[{Methyl(1-naphthyl)phenyl}germyl]phenylacetylene, an acetylene with a bulky chiral germyl group, was polymerized with [(nbd)RhCl]₂-Et₃N to give a high-molecular-weight polymer in good yield. The CD spectrum of the polymer exhibited very large molar ellipticities [θ] in the UV region in non-aromatic solvents (e.g. THF and CHCl₃). In contrast, the CD signals of the polymer in aromatic solvents (e.g. toluene, tetralin, and benzene) became appreciably smaller: [θ]_max=6.4×10⁴ (330 nm) and −4.7×10⁴° cm² dmol⁻¹ (370 nm) in CHCl₃; [θ]_max=1.1×10⁴ (330 nm) and −0.7×10⁴° cm² dmol⁻¹ (370 nm) in toluene. The [θ]_max values of the polymer in aromatic solvents increased when the solutions were heated, which is attributed to decreased π-π interaction between the solvents and side groups.     

Continuous reaction crystallization of struvite from diluted aqueous solution of phosphate(V) ions in the presence of magnesium ions excess

Continuous reaction crystallization of struvite MgNH₄PO₄·6H₂O from diluted aqueous solution containing phosphate(V) ions of concentration 0.20 wt% PO₄³⁻ was investigated experimentally. The tests were carried out in a continuous DT MSMPR type crystallizer in temperature 298 K assuming 20% excess of magnesium ions at the inlet point in respect to struvite synthesis reaction stoichiometry. Influence of pH (8.5–10) and mean residence time of suspension in a crystallizer (900–3600 s) on the product crystals size distribution, their size-homogeneity and process kinetics were identified. Crystals of mean size from ca. 19 to ca. 73 μm, of diverse size-homogeneity (CV 60–87%) were produced. Struvite particles of the largest sizes and acceptable homogeneity were produced at pH 8.5 for prolonged mean residence time 3600 s. Under these conditions struvite nucleation rate did not exceed 5.3 × 10⁷ l/(s m³) according to SIG MSMPR model predictions. Crystal linear growth rate within the investigated process parameter values varied from 3.62 × 10⁻⁹ to 1.68 × 10⁻⁸ m/s. Magnesium ions excess in a process environment influenced yield of continuous reaction crystallization of struvite advantageously – contrary to product crystals quality. Concentration of phosphate(V) ions in mother solution decreased from inlet 0.20 wt% to 0.9 × 10⁻³ – 9.2 × 10⁻³ wt% (9–92 mg/kg) depending on pH and mean residence time of suspension in a crystallizer, what can be regarded as a very good result of their recovering from solution.     

Synthesis, characterization and optical properties of fluorinated poly(aryl ether)s containing phthalazinone moieties

A series of novel fluorinated poly(aryl ether)s containing phthalazinone moieties (FPPEs) have been prepared by a modified synthetic procedure for optical waveguide applications. The obtained random copolymers exhibited excellent solubility in polar organic solvents, high glass transition temperatures (T_gs: 185-269 °C), good thermal stabilities (the temperatures of 1% weight loss: 487-510 °C) and good optical properties. By adjusting the feed ratio of the reactants, the refractive indices of TE and TM modes (at 1550 nm) could be well controlled in the range of 1.575-1.498 and 1.552-1.484, respectively. The optical losses of the FPPEs exhibited relatively low values (less than 0.27 dB/cm at 1310 nm). Additionally, the thermo-optic coefficient (dn/dT) values of the FPPEs at 1310 nm and 1550 nm (TE mode) ranged from −0.97 × 10⁻⁴ °C to −1.33 × 10⁻⁴ °C and from −0.96 × 10⁻⁴ °C to −1.29 × 10⁻⁴ °C, respectively.     

Pure and (zinc or iron) doped titania powders prepared by sol-gel and used as photocatalyst

Pure and doped (zinc and iron) nanocrystalline titania powders were prepared by the sol-gel route. Doping tends to change the existing crystalline phases and their degree of crystallinity, but particle size distribution and morphology of the particles are also affected. In the pure titania system, the main crystalline phase is anatase but rutile is also present. The doped (Zn and Fe) titania crystallizes only as anatase. The undoped titania shows a bimodal distribution of particles size: fine (20-40 nm) and coarse (300-500 nm) grains. The doped TiO₂ powder also exhibits a much more uniform particle size distribution, with all grains under 40 nm.The photocatalytic efficiency of suspended powders was tested on the decolouration of Orange II aqueous solutions under visible artificial light irradiation. The maximum decolouration reached by the pure TiO₂ was 81% at a rate of 3.6 × 10⁻³ min⁻¹. Iron doping decreases the photocatalytic activity; the maximum dye degradation was only 43% at a rate of 1.3 × 10⁻³ min⁻¹. On the contrary, the performance of Zn-doped titania was better, having a decolouration rate of 17.7 × 10⁻³ min⁻¹.     

Electrocatalytic oxidation and simultaneous determination of uric acid and ascorbic acid on the gold nanoparticles-modified glassy carbon electrode

A new gold nanoparticles-modified electrode (GNP/LC/GCE) was fabricated by self-assembling gold nanoparticles to the surface of the l-cysteine-modified glassy carbon electrode. The modified electrode showed an excellent character for electrocatalytic oxidization of uric acid (UA) and ascorbic acid (AA) with a 0.306 V separation of both peaks, while the bare GC electrode only gave an overlapped and broad oxidation peak. The anodic currents of UA and AA on the modified electrode were 6- and 2.5-fold to that of the bare GCE, respectively. Using differential pulse voltammetry (DPV), a highly selective and simultaneous determination of UA and AA has been explored at the modified electrode. DPV peak currents of UA and AA increased linearly with their concentration at the range of 6.0 × 10⁻⁷ to 8.5 × 10⁻⁴ mol L⁻¹ and 8.0 × 10⁻⁶ to 5.5 × 10⁻³ mol L⁻¹, respectively. The proposed method was applied for the detection of UA and AA in human urine with satisfactory result.     

Morphology of undeformed and deformed polyethylene lamellar crystals

Morphology of undeformed polyethylene crystals obtained by high pressure crystallization was investigated by SEM. It was revealed by exposing the interior of the samples by microtoming followed by permanganic etching. The etching procedure was refined to reveal defected sites of lamellae in addition to differentiation of crystalline and amorphous phases. From 1 to 3 screw dislocations with large Burgers vector per 1 μm² of lamellae basal planes were detected. Lamellae, when viewed edge-on give an impression of a “blocky architecture”, while their real shape, as seen on SEM images of flat-on and oblique lamellae, resembles platelets with a few defects in the form of screw dislocations protruding a platelet.High pressure-crystallized polyethylene samples were deformed plastically by uniaxial compression and were studied by SEM and AFM. When the deformation is interrupted dislocations are arrested within the crystals. It was observed that in contrast to undeformed samples, the side faces of deformed lamellae were not any longer smooth and a large number of screw dislocations with low Burgers vectors crossing the lamellae thickness could be distinguished. These observations are in accordance with polymer crystal plasticity theory that relies on the rate controlled nucleation and propagation of screw dislocations across polymer crystals. An existence of numerous screw dislocations arrested in lamellae is a direct proof of action of fine crystallographic slips along the macromolecular chains in PE crystals during plastic deformation. The kinking of lamellae due to plastic deformation was also observed. Large sections of lamellae between kinks rotated towards the plane of compression while the chain stems in lamellae rotated in the opposite direction, away from the compression direction, which is a signature of the fine crystallographic slip.Plastically deformed polyethylene crystals are highly defected due to many dislocations incorporated within them - the density of dislocations was approximated as 10¹⁶ m⁻². However, deformed crystal melting temperature is nearly unaffected while the heat of melting is slightly reduced, yet only in thin crystals. It suggests that the arrested dislocations contribute more to the surface energy of lamellae basal planes rather than to a bulk energy of polyethylene crystals.     

Measurement of through-plane effective thermal conductivity and contact resistance in PEM fuel cell diffusion media

An experimental study was performed to determine the through-plane thermal conductivity of various gas diffusion layer materials and thermal contact resistance between the gas diffusion layer (GDL) materials and an electrolytic iron surface as a function of compression load and PTFE content at 70 °C. The effective thermal conductivity of commercially available SpectraCarb untreated GDL was found to vary from 0.26 to 0.7 W/(m °C) as the compression load was increased from 0.7 to 13.8 bar. The contact resistance was reduced from 2.4×10⁻⁴ m²°C/W at 0.7 bar to 0.6×10⁻⁴ m²°C/W at 13.8 bar. The PTFE coating seemed to enhance the effective thermal conductivity at low compression loads and degrade effective thermal conductivity at higher compression loads. The presence of microporous layer and PTFE on SolviCore diffusion material reduced the effective thermal conductivity and increased thermal contact resistance as compared with the pure carbon fibers. The effective thermal conductivity was measured to be 0.25 W/(m °C) and 0.52 W/(m °C) at 70 °C, respectively at 0.7 and 13.8 bar for 30%-coated SolviCore GDL with microporous layer. The corresponding thermal contact resistance reduced from 3.6×10⁻⁴ m²°C/W at 0.7 bar to 0.9×10⁻⁴ m²°C/W at 13.8 bar. All GDL materials studied showed non-linear deformation under compression loads. The thermal properties characterized should be useful to help modelers accurately predict the temperature distribution in a fuel cell.     

Supercritical fluid extraction of piceid, resveratrol and emodin from Japanese knotweed

In the present study, the use of supercritical fluid extraction was investigated for selected compounds from the plant Japanese knotweed (Polygonum cuspidatum Siebold & Zucc.). The effects of parameters such as type of modifier, pressure, temperature and time on the extraction efficiency of piceid, resveratrol and emodin were studied. The optimal conditions were found as follows: modifier acetonitrile, 40 MPa, 100 °C and 45 min. SFE results were compared with those obtained by conventional Soxhlet extraction carried out for 4 h. The extracts obtained using these two techniques were analysed by liquid chromatography coupled with UV detection. LiChrospher^® 100, RP-18 column (125 mm × 4 mm, 5 μm) coupled with gradient elution acetonitrile in acidified water was used for the separation of compounds at flow rate 0.5 mL min⁻¹. Detection was carried out at 306 nm. Limits of detection were 21, 8 and 52 μg L⁻¹ for piceid, resveratrol and emodin, respectively. The linear range was 0.5-10 mg L⁻¹ for piceid and resveratrol, and 1-50 mg L⁻¹ for emodin with correlation coefficients above 0.9981. Based on the comparison of both methods extracted amount of piceid by Soxhlet extraction is approximately 10 times higher than by SFE method, while the extraction yield of emodin by Soxhlet extraction in approx. 2.5 times lower than by SFE. The advantage of SFE over Soxhlet extraction method is more than 5 times shorter extraction time period.     

Influence of crystal size and probe molecule on diffusion in hierarchical ZSM-5 zeolites prepared by desilication

The improvement of molecular transport properties of hierarchical H-ZSM-5 obtained by desilication was evidenced by studying the desorption of o-xylene and isooctane by in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). This technique enabled monitoring simultaneously bands associated with the molecular probes and the zeolite, using powdered sample masses as low as 1 mg. Two H-ZSM-5 samples with markedly different crystal sizes were investigated. The first sample was commercial and consisted of small crystallites (ca. 250 nm). The second sample were laboratory-made large crystals with coffin-like shape (ca. 17 × 4 × 4 μm³). The hierarchical derivatives of the small and large zeolite crystals displayed 250 and 120 m² g⁻¹ of mesopore surface area, respectively, in contrast to the 62 and 5 m² g⁻¹ of the parent counterparts. The data based on o-xylene desorption were partly disguised by site-desorption limitations. Desorption experiments using isooctane evidenced a 4-fold reduction in the characteristic diffusion path length on both mesoporous small and large zeolites with respect to their purely microporous analogues. These results confirm the substantial potential for improvement of commercial nanocrystalline zeolites in diffusion-limited reactions upon the introduction of intra-crystalline mesoporosity by post-synthesis modification.     

The influence of temperature and strain rate on the constitutive and damage responses of polychlorotrifluoroethylene (PCTFE, Kel-F 81)

Polychlorotrifluoroethylene (PCTFE), also known as Kel-F 81, is a semi-crystalline fluoropolymer. Although it has been employed in a wide range of cryogenic components, valve seats, seals, and microelectronics packaging, its mechanical behavior has received limited coverage in the literature. In this work, we present the tensile and compressive constitutive response of PCTFE for a range of temperatures (−85 to 150 °C) and strain rates (1 × 10⁻⁴-2.9 × 10³ s⁻¹). Both large-strain experiments based on flow stress and small-strain dynamic mechanical analysis (DMA) using the elastic modulus exhibit a strong increase in the glass transition temperature, T_g, with increasing strain rate. The quasistatic fracture behavior of PCTFE is presented using J-integral fracture experiments. Finally, a discussion of the implication of the constitutive and damage responses of PCTFE on impact failure modes observed in Taylor impact experiments is presented.     

The properties of poly(tetrafluoroethylene) (PTFE) in compression

Samples of DuPont 7A and 7C Teflon (PTFE, poly(tetrafluoroethylene)) were tested in compression at strain-rates between 10⁻⁴ and 1 s⁻¹ and temperatures between −198 and 200 °C. Additionally, using a Split-Hopkinson pressure bar, a temperature compression series was undertaken between −100 and 150 °C at a strain rate of 3200 s⁻¹. To investigate the small-strain response, strain gauges were used to measure axial and transverse strain allowing the Poisson ratio to be quantified. As expected, the mechanical properties were found to be strongly affected by strain-rate and temperature. Moduli were found by several methods and the trend, with respect to temperature, lends weight to the suggestion that the glass-transition temperature of PTFE is ≈−100 °C. The physical properties of the sintered PTFE were measured and the crystallinities measured by several techniques.     

Sulfonated poly(ether ether ketone) membranes crosslinked with sulfonic acid containing benzoxazine monomer as proton exchange membranes

The incorporation of benzoxazine (Ba) or sulfonic acid containing benzoxazine (SBa) as a crosslinking agent in SPEEK proton exchange membrane (PEM) can substantially improve the SPEEK membrane performance. The SPEEK-SBa membranes give higher effective selectivity than corresponding SPEEK-Ba membranes under close crosslinker loading and thus are more suitable to be used in direct methanol fuel cells. The best achieved SPEEK-SBa composition (SBa40) gives reasonable proton conductivity (0.91 × 10⁻² S cm⁻¹) but significantly lower methanol permeability (6.5 × 10⁻⁸ S² cm⁻¹). The achieved effective selectivity (Φ = SPEEK-SBa40: 14.0 × 10⁴ S s cm⁻³) is substantially higher than the plain SPEEK (Φ = 7.24 × 10⁴ S s cm⁻³) which has great potential for practical applications in DMFCs.