Synthesis and characterization of differently substituted phenyl hepta isobutyl‐polyhedral oligomeric silsesquioxane/polystyrene nanocomposites

Variously substituted polyhedral oligomeric silsesquioxanes (POSSs)/polystyrene (PS) nanocomposites of general formula R₇R′(SiO_1.5)₈/PS (where R = isobutyl and R′ = 4‐methoxyphenyl, 4‐methylphenyl, 3,5‐dimethylphenyl, 4‐fluorophenyl, 2,4‐difluorophenyl, 4‐chlorophenyl) were prepared by in situ polymerization of styrene in the presence of 5% w/w of POSS. The actual filler concentration in the obtained nanocomposites was checked by ¹H NMR spectroscopy. Scanning electron microscopy and FTIR spectroscopy evidenced the presence of filler‐polymer interactions. Inherent viscosity (η_inh) determinations indicated that the average molar mass of polymer in halogenated derivatives was lower than neat PS, and were in agreement with calorimetric glass transition temperature (T_g) measurements. Finally, a comparative study concerning the thermal stability of synthesized nanocomposites was carried out in both inert (flowing nitrogen) and oxidative (static air) atmospheres into a thermobalance, in the scanning mode, at 10°C min⁻¹, and the temperatures at 5% mass loss (T_5%), of various compounds were determined. The results were discussed and interpreted. POLYM. COMPOS., 35:151–157, 2014. © 2013 Society of Plastics Engineers     

Synergistic effect of dual nanofillers (MWCNT and Ni–Al LDH) on the electrical and thermal characteristics of polystyrene nanocomposites

The advantage of using 3D hybrid filler containing carboxylic acid functionalized multiwalled carbon nanotubes (c‐MWCNTs) and sodium dodecyl sulfate modified Ni–Al layered double hydroxide (sN‐LDH) over c‐MWCNTs and sN‐LDHs acting alone was investigated. PS/c‐MWCNT composites proved to be good for improvement of properties, but not to an appreciable level, especially in case of electrical conductivity, flame retardancy, rheology, and water vapor permeability. Hence, a combination of 0.3 wt % of c‐MWCNT and 3 wt % of sN‐LDH was optimized as additives to assist in the full expression of the filler traits in the nanocomposite and to obtain a versatile nanocomposite with properties specific to both the fillers. This approach slightly decreases the dispersion challenge faced with handling high loadings of CNT and also the intrinsic limitations specific to the individual fillers (i.e., inertness of CNTs and low conductivity of LDHs). Moreover, the anion/anionic repulsion of organically modified CNT/LDH facilitates effective dispersion of the additive opposing adhesion. FTIR and Raman spectroscopy provided evidence for incorporation and proper dispersion of the additives in the polymer matrix, with XRD and TEM confirming a well‐dispersed morphology of the nanocomposites. In this work, focus is made on the improvement of thermal stability, flame retardancy, melt rheology, hardness, electrical conductivity, and water vapor permeability of PS/0.3 wt % c‐MWCNT/3 wt % sN‐LDH nanocomposites over PS/0.3 wt % c‐MWCNT, making use of the synergistic effect of c‐MWCNT coupled with sN‐LDH on polystyrene. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46513.     

Synthesis and characterization of polystyrene/layered double‐hydroxide nanocomposites via in situ emulsion and suspension polymerization

Polystyrene (PS)/ZnAl layered double‐hydroxide (LDH) nanocomposites were synthesized via in situ emulsion and suspension polymerization in the presence of N‐lauroyl‐glutamate surfactant and long‐chain spacer and characterized with elemental analysis, Fourier transform infrared spectrum, X‐ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetric analysis. The XRD and TEM results demonstrate that the exfoliated ZnAl–LDH layers were well dispersed at molecular level in the PS matrix. The completely exfoliated PS/LDH nanocomposites were obtained even at the 20 and 10 wt % LDH loadings prepared by emulsion polymerization and suspension polymerization, respectively. The PS/LDH nanocomposites with a suitable amount of LDH showed apparently enhanced thermal stability. When the 50% weight loss was selected as a comparison point, the decomposition temperature of the exfoliated PS/LDH sample prepared by emulsion polymerization with a 5 wt % LDH loading was about 28°C higher than that of pure PS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3758–3766, 2006     

Thermal study on phenyl,hepta isobutyl‐polyhedral oligomeric silsesquioxane/polystyrene nanocomposites

A comparative study concerning the thermal stability of polystyrene (PS) and three polyhedral oligomeric silsesquioxane/polystyrene (POSS/PS) nanocomposites of formula R₇R′(SiO_1.5)₈/PS (where R = isobutyl and R′ = phenyl), at various (3, 5, and 10%) POSS concentration was carried out in both inert (flowing nitrogen) and oxidative (static air) atmospheres. Nanocomposites were synthesized by in situ polymerization of styrene in the presence of POSS and the experimental filler concentration in the obtained compounds, determined by ¹H NMR spectroscopy, was in all cases slightly higher than that in the reactant mixtures. Inherent viscosity (η_inh) determinations indicated that the average molar mass of polymer in the nanocomposites was practically the same than neat PS and were in agreement with calorimetric glass transition temperature (T_g) measurements. The temperature at 5% mass loss (T_5%) and the activation energy (E_a) of degradation process of synthesized nanocomposites were determined and compared with each other and with those of unfilled PS. On the basis of the results from thermal and IR spectroscopy characterizations, nanocomposite with 5% of molecular filler appears the most thermally stable. The results were also compared with literature data on similar PS‐based nanocomposites. POLYM. COMPOS., 2013 © 2013 Society of Plastics Engineers     

Synthesis and thermal characterization of new dumbbell shaped POSS/PS nanocomposites: Influence of the symmetrical structure of the nanoparticles on the dispersion/aggregation in the polymer matrix

A series of three novel dumbbell shaped polyhedral oligomeric silsesquioxanes (POSS)/ polystyrene (PS) nanocomposites, at different POSS contents (3%, 5% and 10% w/w), was synthesized and characterized in order to investigate the effects of this new bridged structure on the filler‐polymer interaction and then on the thermal behavior of the obtained polymer nanostructured materials (PNMs). Nanocomposites were synthesized by in situ polymerization of styrene and the actual POSS concentration in the obtained PNMs was checked by ¹H NMR spectroscopy. Scanning electron microscopy (SEM) and FTIR spectroscopy evidenced, at the same time, the presence of filler‐polymer interactions and auto‐aggregation phenomena. Degradations were carried out into a thermobalance, in the scanning mode, at various heating rates in both inert and oxidative atmospheres. The characteristic parameters of thermal stability, namely temperature at 5% mass loss and the apparent activation energy of degradation, for the various nanocomposites were determined and an increase in the initial decomposition temperatures of PNMs with increasing the POSS contents was observed. The results are discussed and interpreted. POLYM. COMPOS., 36:1394–1400, 2015. © 2014 Society of Plastics Engineers     

Preparation and characterization of exfoliated layered double hydroxide/silicone rubber nanocomposites

Silicone rubber (SR)/Mg–Al layered double hydroxide (LDH) nanocomposites were prepared by the solution intercalation of SR crosslinked by a platinum‐catalyzed hydrosilylation reaction into the galleries of dodecyl sulfate intercalated layered double hydroxide (DS–LDH). X‐ray diffraction and transmission electron microscopy analysis showed the formation of exfoliated structures of organomodified LDH layers in the SR matrix. The tensile strength and elongation at break of SR/DS–LDH (5 wt %) were maximally improved by 53 and 38%, respectively, in comparison with those of the neat polymer. Thermogravimetric analysis indicated that the thermal degradation temperature of the exfoliated SR/DS–LDH (1 wt %) nanocomposites at 50% weight loss was 20°C higher than that of pure SR. Differential scanning calorimetry analysis data confirmed that the melting temperature of the nanocomposites increased at lower filler loadings (1, 3, and 5 wt %), whereas it decreased at a higher filler loading (8 wt %). The relative improvements in the solvent‐uptake resistance behavior of the SR/DS–LDH nanocomposites were also observed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermoplastic polyurethane and nitrile butadiene rubber blends with layered double hydroxide nanocomposites by solution blending

Polymer blending coupled with nanofillers has been widely accepted as one of the cheaper methods to develop high‐performance polymeric materials for various applications. In the present work, dodecyl sulfate intercalated Mg? Al‐based layered double hydroxide (DS‐LDH) was used as nanofiller in the synthesis of polyurethane blended with nitrile butadiene rubber (PU/NBR; 1:1 w/w) nanocomposites, which were subsequently characterized. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed the partial dispersion of Mg? Al layers in PU/NBR blends at lower filler content followed by aggregation at higher filler loading. In comparison to the neat PU/NBR blend, the tensile strength (156%) and elongation at break (21%) show maximum improvement for 1 wt% filler loading. The storage and loss moduli, thermal stability and limiting oxygen index of the nanocomposites are higher compared to the neat PU/NBR blend. Glass transition temperature and swelling measurements increase up to 3 wt% DS‐LDH loading in PU/NBR compared to either neat PU/NBR or its other corresponding nanocomposites. XRD and TEM analyses indicate the partial distribution of DS‐LDH in PU/NBR blends suggesting the formation of partially exfoliated nanocomposites. The improvements in mechanical, thermal and flame retardancy properties are much greater compared to the neat blend confirming the formation of high‐performance polymer nanocomposites. Copyright © 2009 Society of Chemical Industry     

Melt-spinning of LDH/HDPE nanocomposites

Melt-spinning of layered double hydroxide (LDH)/high density polyethylene (HDPE) nanocomposites was reported for the first time. Initially LDH/HDPE nanocomposites were prepared by melt-mixing, in which clay loadings were up to 3 wt% while compatibilizer to clay ratio was kept to be 2:1. LDHs were hydrophobically modified by hexadienoic acid, tetradecanoic acid, and octadecanoic acid to overcome the incompatibility between matrix polymer and LDH. The organomodified LDH showed different interlayer arrangements. Both the modifications and the processing conditions affected the properties of melt-spun fibers. Nanocomposites were rheologically characterized by using a classical semi-quantitative method and additionally by a rather new method, which is an interpretation of Carreau–Yasuda model. Tetradecanoic acid modified LDH at 1 wt% filler loading was found to give most notable results.     

Synthesis and characterization of PS-clay nanocomposite by emulsion polymerization

Summary Polystyrene-Na⁺-montmorillonite(PS-Na⁺-MMT) nanocomposites are prepared by a simple emulsion polymerization. The X-ray diffraction(XRD) and infrared spectroscopy (IR) analysis confirm that polystyrene(PS) macromolecules can be inserted between lamella layers and whose layer separation is consequently higher than in the polymer-free clay. The enhanced thermal properties of composites are measured by differential scanning calorimetry(DSC) and thermogravimetric analysis(TGA) thermogram and indicate that the glass transition and the decomposition onset temperature of obtained nanocomposites are found to be moved to the higher temperature region. The increased Young's modulus of the obtained nanocomposites is ascribed to the intercalation of PS in clay galleries as well as the fine dispersion of clay particles into the polymer matrix. Received: 23 February 1999/Revised version: 26 March 1999/Accepted: 1 April 1999     

Effect of doubly organo-modified vermiculite on the properties of vermiculite/polystyrene nanocomposites

Vermiculite (Verm)/polystyrene (PS) nanocomposites were prepared by dispersing a doubly organo-modified Verm (DOVerm) in PS via in situ polymerization (DOVerm/PS 1/99, 3/97, 5/95, and 7/93 mass/mass ratios). The morphology of Verm/PS nanocomposites evolved three stages as the content of DOVerm decreased in the nanocomposites: intercalation at high filler content, intermediate state of intercalation to exfoliation, and exfoliation of Verm in PS matrix with a low filler content. The morphological changes of Verm/PS nanocomposites were confirmed by the X-ray diffraction (XRD) patterns and the transmission electron microscopy (TEM) images. Compared with the pure PS, the nanocomposites filled with Verm showed significant enhancements on thermal stability and dynamic mechanical properties. Interestingly, the nanocomposites filled with 1 and 7 mass% of DOVerm exhibited more pronounced effects of Verm on the properties. It was proved that the double organo-modification clearly enhanced the ultimate properties of the Verm/PS nanocomposites.     

Synthesis and characterization of polyurethane/Mg‐Al layered double hydroxide nanocomposites

Layered double hydroxide (LDH) is a new type of nanofiller, which improves the physicochemical properties of the polymer matrix. In this study, 1, 3, 5, and 8 wt % of dodecyl sulfate‐intercalated LDH (DS‐LDH) has been used as nanofiller to prepare a series of thermoplastic polyurethane (PU) nanocomposites by solution intercalation method. PU/DS‐LDH composites so formed have been characterized by X‐ray diffraction and transmission electron microscopy analysis which show that the DS‐LDH layers are exfoliated at lower filler (1 and 3 wt %) loading followed by intercalation at higher filler (8 wt %) loading. Mechanical properties of the nanocomposite with 3 wt % of DS‐LDH content shows 67% improvement in tensile strength compared to pristine PU, which has been correlated in terms of fracture behavior of the nanocomposites using scanning electron microscope analysis. Thermogravimetric analysis shows that the thermal stability of the nanocomposite with 3 wt % DS‐LDH content is ≈ 29°C higher than neat PU. Limiting oxygen index of the nanocomposites is also improved from 19 to 23% in neat PU and PU/8 wt% DS‐LDH nanocomposites, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

In situ synthesis,morphology, and thermal properties of polystyrene—MgAl layered double hydroxide nanocomposites

Polystyrene (PS)/layered double hydroxide (LDH) nanocomposites were synthesized by in situ free radical bulk polymerization. LDH formed by magnesium and aluminum (Mg:Al—molar ratio of 2:1) was prepared by coprecipitation method and intercalated with sodium dodecyl sulfate (DDS). The nanocomposites were characterized by X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and flammability test. The XRD and TEM demonstrated that synthesized nanocomposites in all compositions studied showed a high global dispersion of LDH in PS, suggesting exfoliation. The results of TGAs (when 50% mass loss was selected as a comparison point) and flammability tests for synthesized nanocomposites, presented a significant improvement in thermal stability and flammability property when compared with pure PS. This behavior and properties indicate application of the surfactant intercalated LDH reinforced PS in fields where thermal stability is an important characteristic. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Effect of cooling rate on the surface resistivity of polymer/multi‐walled carbon nanotube nanocomposites

In this study, ethylene‐vinyl acetate copolymer (EVA) and polystyrene (PS) were melt‐mixed with multi‐walled carbon nanotube (CNT) (MWCNT), respectively. The effect of mixing time, rotor speed, and cooling rate on surface resistivity was investigated. EVA/MWCNT and PS/MWCNT nanocomposites with percolation threshold <1 wt% of MWCNT were prepared using conventional melt‐compounding method. When fast cooling was applied for these nanocomposites, a surface resistivity of 10⁶ Ω/square was obtained at around 7 wt% of MWCNT for EVA and 10⁵ Ω/square at around 3.5 wt% of MWCNT for PS. However, when slow cooling was applied, a surface resistivity of 10⁶ Ω/square was obtained at 0.75 wt% of MWCNT for EVA and 10⁵ Ω/square at around 0.5 wt% of MWCNT for PS. To the best of our knowledge, this is the first report which recognizes the importance of cooling rate on the surface resistivity of polymer/MWCNT nanocomposites. This finding may be potential to the commercialization of the CNT‐based polymer nanocomposites. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Rheological and electrical percolation thresholds of carbon nanotube/polymer nanocomposites

Percolation thresholds of multiwalled carbon nanotube/polystyrene (MWCNT/PS) nanocomposites (NC) were determined by rheology and electrical conductivity. The percolation threshold found by electrical conductivity was 0.5% carbon nanotubes (CNT) and that by mechanical spectroscopy and relaxation measurements was 0.9% CNT. These results together with those reported in the literature show several types of percolation thresholds, depending on the average filler–filler (CNT and/or aggregates) distance in a polymer matrix. A distance close to polymer gyration radius corresponds to a “soft” rheological threshold (P_{C rheo}^soft). Close contacts between fillers giving rise to a conductive path corresponds to an electrical threshold (P_{C elec}). At high filler concentration, fillers form a network, corresponding to a “rigid” rheological threshold (P_{C rheo}^rigid). These thresholds depend on the filler content and follow the order: P_{C elec}^soft < P_{C elec} < P_{C rheo}^rigid. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

An investigation on the bound rubber and dynamic mechanical properties of polystyrene particles‐filled elastomer

Polymeric nanoparticles have many advantages as the reinforcing filler of rubber. To investigate the mechanism of the reinforcement, nanocomposites of poly(styrene‐butadiene) rubber (SBR) filled with polystyrene (PS) particles as the reinforcing agents was prepared. Morphology and dynamical mechanical properties of PS particles‐filled SBR were investigated. It was found that the polymer chains of the elastomer could be absorbed onto the PS particles, in reminiscent to the concept of bound rubber in inorganic filler‐filled elastomeric system. The adsorbed polymer layer can form up glassy bridges between neighboring filler particles, leading to the agglomeration of the filler particles and the reinforcement of the elastomer. With higher filler content or smaller filler size, the numbers of the glassy bridges increase, and the modulus of the elastomer increases. With higher strain or higher temperature, the filler–filler interaction is disrupted and the material is softened. The study discovered the existence of bound rubber in PS particles‐filled elastomer and illustrated its influence on the dynamic mechanical properties, which could be helpful to design the polymeric nanoparticles for rubber reinforcement. POLYM. COMPOS., 38:1112–1117, 2017. © 2015 Society of Plastics Engineers     

Effect of hybrid reinforcement based on precipitated silica and montmorillonite nanofillers on the mechanical properties of a silicone rubber

Silicone rubber (SR) nanocomposites containing precipitated silica (PS), montmorillonite (MMT), and PS/MMT hybrid fillers were prepared through melt‐mixing technique. In the SR/PS/MMT nanocomposite, the hybrid filler weight ratio was increased progressively from 0.4 to 1.7 while keeping the MMT weight constant. The viscosity, cure characteristics, and mechanical properties of the nanocomposites were subsequently measured. The optimum cure time increased, and the scorch time and rate of cure decreased. Furthermore, when the hybrid filler weight ratio was raised to its optimum, the tensile strength, Young's modulus, modulus at 100 and 300% elongation (M100 and M300), elongation at break, stored energy density at break, and hardness of the nanocomposite improved. The stress–strain properties of the nanocomposite with the hybrid filler improved at high deformation in comparison with those containing the PS and MMT fillers. The MMT filler exfoliated in the SR/MMT nanocomposite but did not in the nanocomposites containing the hybrid filler. Notably, the mechanical properties of the nanocomposite benefitted from the hybrid filler. This was due to the filler–filler and filler–rubber network formation in the rubber by the PS particles. Finally, effect of the PS, MMT, and hybrid fillers on the energy loss or hysteresis of the rubber was measured. POLYM. ENG. SCI., 54:1909–1921, 2014. © 2013 Society of Plastics Engineers     

Electrical and mechanical properties of acrylonitrile‐butadiene‐styrene/multiwall carbon nanotube nanocomposites prepared by melt‐blending

The electrical properties in polymer/carbon nanotube (CNT) nanocomposites are governed not only by the degree of dispersion but also to a greater extent on the aspect ratio of the CNTs in the final composites. Melt‐mixing of polymer and CNTs at high shear rate usually breaks the CNTS that lowers the aspect ratio of the nanotubes. Thus, homogeneous dispersion of CNTs while retaining the aspect ratio is a major challenge in melt‐mixing. Here, we demonstrate a novel method that involves melt‐blending of acrylonitrile‐butadiene‐styrene (ABS) and in situ polymerized polystyrene (PS)/multiwalled CNT (MWCNT) nanocomposites, to prepare electrically conducting ABS/MWCNT nanocomposites with very low CNT loading than reported. The rationale behind choosing PS/MWCNT as blending component was that ABS is reported to form miscible blend with the PS. Thus, (80/20 w/w) ABS/(PS/MWCNT) nanocomposites obtained by melt‐blending showed electrical conductivity value ≈1.27 × 10^?6 S cm^?1 at MWCNT loading close to 0.64 wt %, which is quite lower than previously reported value for ABS/MWCNT system prepared via solution blending. Scanning electron microscopy and differential scanning calorimetry analysis indicated the formation of homogenous and miscible blend of ABS and PS. The high temperature (100°C) storage modulus of ABS (1298 MPa) in the nanocomposites was increased to 1696 MPa in presence of 0.64 wt % of the MWCNT. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Multiscale characterization of filler dispersion and origins of mechanical reinforcement in model nanocomposites

We report on the influence of parameters controlling filler dispersion and mechanical reinforcement in model nanocomposites. We elaborate a series of nanocomposites and present a structural characterization of silica dispersion in polymer matrix for several particle sizes and polymer matrices, at all relevant scales, by coupling Small Angle X-ray Scattering and Transmission Electronic Microscopy. The mechanical properties are investigated in the linear regime by coupling Dynamical Mechanical Analysis and plate/plate rheology. The results show that: (i) for all filler sizes and matrices, a structural transition is observed from non-connected fractal aggregates at low silica concentration to connected network at high particle content. (ii) In the dilute regime, the reinforcement implies a polymer chain contribution with different possible origins: increase of entanglements density for PS and increase of friction coefficient for PMMA. (iii) In the concentrated regime, for a given polymer, the reinforcement amplitude can be tuned by the rigidity of the filler network, which directly depends on the particle–particle interaction.     

Preparation and properties of exfoliated nanocomposites through intercalated a photoinitiator into LDH interlayer used for UV curing coatings

The exfoliated polymer/layered double hydroxide (LDH) nanocomposites based on MgAl were prepared through intercalating a photoinitiator into LDH interlayer, following by UV irradiation induced polymerization. The fragmental photoinitiator, 2-hydroxy-2-methyl-1-phenylpropane-1-one (1173) firstly reacted with isophorone diisocyanate (IPDI) to obtain the semiadduct, 1173-IPDI, and then reacted with the LDH modified by aminoundecanoic acid, obtaining LDH-1173 with an intercalated microstructure, which was characterized by FTIR, XRD, and TGA measurements. The obtained LDH-1173 was mixed with the multifunctional acrylate oligomer and monomer, and then exposed to a UV lamp to prepare a polymer/LDH nanocomposite. From the XRD, TEM and HR-TEM analysis, as well the photopolymerization kinetics investigation, it was found that the LDH-1173 effectively initiated the photopolymerization of acrylates, and formed exfoliated polymer/LDH nanocomposites. However, the mostly intercalated polymer/LDH nanocomposites were obtained for the systems with additional 1173 except for LDH-1173 addition. Compared with the pure polymer material, both the exfoliated and intercalated polymer/LDH nanocomposites exhibited the enhancements in mechanical and thermal properties, as well as hardness.     

Preparation and flame retardancy of polystyrene nanocomposites based on layered double hydroxides

Various layered double hydroxides (LDHs), including MgAl, CoAl, NiAl, and ZnAl‐LDHs, were synthesized and modified using sodium dodecyl benzene sulfonate. Nonhalogen flame‐retardant PS/LDHs nanocomposites were prepared via melt mixing method. The structure of PS/LDHs nanocomposites was investigated by Fourier‐transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD) pattern technique, and scanning electronic microscope. Results from XRD indicated that intercalated/exfoliated structure was achieved in the polystyrene matrix. Dynamic mechanical thermal analysis suggested that the storage modulus and T _g for the PS/LDHs nanocomposites was efficiently improved. Thermal and flammability properties of PS nanocomposites were investigated using thermogravimetry and cone calorimetry. Thermal analysis was evaluated and the prepared nanocomposites showed slightly lower thermal stability probably due to the presence of LDH, which starts to decompose at a lower temperature. Compared with neat PS, the peak heat release rate of PS/MgAl and PS/ZnAl‐LDHs nanocomposites filled with 5 wt% LDHs is reduced by 7% and 12%, respectively. Among all LDHs, MgAl, and ZnAl‐LDHs had a better smoke suppression effect with a reduction of peak smoke production rate and CO release rate of 37% and 44%, respectively. POLYM. COMPOS., 38:1680–1688, 2017. © 2015 Society of Plastics Engineers