气升式环流反应器特性参数的研究进展

介绍了气升式环流反应器的工作原理、分类及流型,综述了气升式环流反应器的流体力学特征参数(主要包含气含率和循环液速)、混合及传质特性参数的测量方法和影响因素。介绍了气含率和循环液速的数学模型,并评述了现有模型。展望了气升式环流反应器进一步的研究方向与发展前景。     

气升式环流反应器特性参数的研究进展

介绍了气升式环流反应器的工作原理、分类及流型,综述了气升式环流反应器的流体力学特征参数(主要包含气含率和循环液速)、混合及传质特性参数的测量方法和影响因素。介绍了气含率和循环液速的数学模型,并评述了现有模型。展望了气升式环流反应器进一步的研究方向与发展前景。     

气升式振荡环流反应器的数值模拟和结构优化

气升式振荡环流反应器（ARLR）作为一种新型的气升式环流反应器,能够有效地提高反应器的气含率和传质系数,并已得到生物发酵实验的验证。本文通过CFD的手段研究了反应器内的流动和传质状况,并利用CFD模拟和响应面分析相结合的方法,优化了反应器的结构参数,如高径比（H/D）、升液区降液区面积之比、导流筒高度等。经过实验测量,优化后的气升式振荡环流反应器与传统的气升式环流反应器相比,气含率提高了32%以上,传质系数提高了11%以上。结果表明,气升式振荡环流反应器作为生化反应器有着非常广阔的应用空间。     

气升-射流式多段环流反应器的流体力学和传质特性

气升式环流反应器在气液或气液固三相反应以及分离过程应用广泛,为提高气液分布和传质性能,在气升式多段环流反应器的第2段引入射流,开发一种气升-射流式多段环流反应器.在160 L的实验装置中,以水-空气体系,研究了气升-射流式多段环流反应器的流体力学和传质特性.射流可减小上升气泡的弦长,提高总体气含率,改善下降段气液分布,...     

气升式环流反应器的实验及数值模拟研究进展

介绍了气升式环流反应器的概况,综述了气升式环流反应器实验及流体数值模拟研究的进展,包括实验方法的不断改进及模型的选取,并提出了今后研究工作的主攻方向.     

气升式内环流反应器流场及传质特性数值模拟

采用双流体模型和气液二相流体动力学理论建立了气升式环流反应器流体流动的数学模型,在此模型的基础上利用溶质渗透理论和各向同性湍流理论建立了局部液相体积传质系数数学模型。采用计算流体软件F luent对气升式环流反应器内气液二相流动状况进行模拟,模拟结果较好地解释了气升式环流反应器内的流动行为及传质特性。模拟计算值与文献实验值的吻合说明了模型的可行性。     

螺旋气升式内环流反应器流动特性

以水和空气两相系统为研究对象,建立螺旋气升式内环流反应器冷模实验装置,采用压差法测定导流筒升流区气含率,用电导法分别实测了升流区液相速度和反应器混合时间,研究螺旋气升式内环流反应器的流动特性,并与传统气升式内环流反应器的流动特性进行对比研究。结果表明,加螺环后反应器气含率明显增加,平均增幅为20%,升流区液相表观速度减小,混合时间增加。     

气升式环流反应器的特性及应用

综述了气升式环流反应器的特性及其主要影响因素研究,简要介绍了这种反应器的应用情况,并提出了今后研究工作的方向。     

用于微生物石油脱蜡的新型气升环流反应器

本文报导了一种新型气升环流反应器,对反应器中液相流型、气含率与操作条件之间的关系进行了实验考察。利用气升环流反应器强化传质和混合的原理,将一个100m^3鼓泡塔反应器改造成三管循环的气升环流反应器,发酵试验结果表明气升环流反应器微生物脱蜡周期比原鼓泡反应器缩短4倍,气升环流反应器能耗比鼓泡反应器降低约30％。     

新型气升式环流反应器液相破碎效果的实验比较

针对石油废水生物降解过程中所遇到的水相、油相难以快速均匀混合的问题,通过对气升式环流反应器动力学原理的分析,在其基础上进行了改进,设计出新型气升式环流反应器,通过验证了推理设计的正确。在本新型气升式反应实验中,以煤油和水为介质,０．４ｍ＾３／ｈ的通气量是较佳的工作条件,证明了新型气升式反应器处理特殊条件液液两相均匀混合的可行性。     

气升式环流反应器处理石化废水研究

采用气升式环流反应器作为曝气装置，研究了其处理石化废水的有效性，及不同操作参数对废水处理效果的影响。结果表明，气升式环流反应器能够有效用于石化废水的生物处理，出水能够达到石化废水国家二级排放标准。驯化后活性污泥中出现丰富的微生物相，降解反应过程符合一级反应动力学模型。活性污泥浓度和水力停留时间对降解反应有重要影响，且存...     

K型气升式外环流碳化塔中试研究

在化肥厂进行了用带有K型折流元件的气升式外环流反应器取代鼓泡式碳化塔的中试.结果表明,该型反应器具有造价低、维修少和显著强化碳化过程等优点.该型反应器的基本原理也适应于其他化学反应器和生物反应器的设计.     

Air-lift reactors in chemical and biological technology

The principle of the air-lift reactor is finding wide application in the fields of both chemical technology and biotechnology because it offers simple and effective mixing in three-phase processes involving gases, liquids and solids. The air-lift principle offers advantages of no moving parts, high gas absorption efficiency, good heat transfer characteristics and rapid mixing which are applicable in a range of industrial processes. This review considers specific aspects of air-lift reactors emphasizing their function and relevance to particular applications. The two main groups of air-lift reactor, baffled vessels and external loop reactors, have four main component parts in common, the riser, the downcomer, the base and the gas separator, all of which have distinct characteristics. The performance of these four components with respect to flow configurations, fluidization of suspended solids and mass transfer are discussed together with methods of evaluating mass transfer coefficients.     

气提泵中标准孔板流量计特征

探讨了气提泵输送水,模拟料液,30％三烷基氧膦-煤油溶液时标准孔板流量计两端压降特征。实验结果表明,由于气提泵中气液相互作用,造成了标准孔板流量计两端的压降随时问呈周期性的波动特征;而压降的时均值与流经孔板的液体平均流量之间呈线性关系。     

Liquid/solid mass transfer in an air-lift loop reactor with a dispersed solid phase

In processes with immobilized cells mass transfer across the boundary layer surrounding the support often plays an important role. Relatively little is known about external mass transfer as a function of the superficial gas velocity in bioreactors such as air-lift loop reactors. In this work ion-exchange resins were used as a solid phase to determine the mass-transfer coefficient in such a reactor. Relations between the Sherwood number and the superficial gas velocity were derived and compared with relations from the literature. Relations in which the Sherwood number is a function of the energy-dissipation rate and relations in which the relative particle velocity is calculated from the rate of free fall of the particle were compared. It was shown that the Sherwood numbers that were functions of the energy-dissipation rates were higher than could be calculated on the basis of the rate of free fall. The Sherwood number obtained was used to calculate the k_l,s of carrageenan gel beads as a solid phase in an air-lift loop reactor. © 1998 SCI.     

提高发酵过程乙醇分离效率的新型反应器

设计了一种新型的带侧臂循环的气升式反应器,该反应器可以有效地把真空闪蒸发酵和汽提发酵2项技术结合起来。实验结果表明,与单独的汽提和闪蒸过程相比,利用此反应器进行同步汽提闪蒸操作,大大提高了乙醇的移出效率,从而进一步提高了发酵强度。     

Hydrodynamics in rectangular air-lift reactors: Scale-up and the scale-up and the influence of gas-liquid separator design

Experiments were conducted on air-lift reactors with different liquid volumes, aspect ratios, and gas-liquid separator configurations, with constant downcomer to riser cross-sectional area ratio and riser/downcomer height. Reactor performance was highly dependent on the gas-liquid separator design. By changing the latter, the mode of operation could be changed from that of a concentric tube reactor (with gas recirculation) to an external loop reactor (without gas recirculation). Liquid velocity and overall gas hold-up data were correlated to the power per liquid volume and “Disengagement Ratio”, a geometric parameter describing the separator's configuration. During scale-up, similar gas hold-ups and liquid velocities were found in laboratory and pilot reactors. A modified air-lift reactor with an enlarged channel for a gas-liquid separator also was studied.     

HYDRODYNAMIC MODELLING IN AN AIR-LIFT LOOP REACTOR

A simple hydrodynamic model is proposed for use in the design, scale-up and characterization of external loop air-lift reactors. The approach is based upon a momentum balance for the flow loop coupled with a drift-flux equation for the reactor riser and establishes a rational basis for a predictive model relating gas throughput to induced liquid flow and gas hold-up in a range of air-lift reactors. The effective resistance of the reactor, k, defined in terms of the total loss coefficients of the reactor and the aerated height of the two-phase riser, was identified to allow for the quantification of the influence of reactor design on the hydrodynamic variables. An extensive body of data for the air-water system, collected on two reactors with active volumes of 0·055 m³ and 0·3 m³, is presented and used, in conjunction with literature data encompassing a wide range of reactor geometries and flow conditions, to define a unique relationship between flow behaviour and reactor configuration. The model, which accounts for the prevailing flow regime in the reactor, provides a direct method of predicting hydrodynamic behaviour in relatively non-viscous systems.     

气提泵特性研究

研究了水、模拟料液、30%TRPO-煤油体系3种液体在高为6.2m气提泵中的气提特征,并用Parker一维模型对实验结果进行了分析和处理。详尽讨论了提升管管径、输送液体的粘度和表面张力对Parker模型中特征参数K、S的影响。