Transport property and battery discharge characteristic studies on 1−x(0.75Agl∶0.25AgCl)∶ xAl2O3 composite electrolyte system

Various experimental studies on a new fast Ag⁺ ion-conducting composite electrolyte system: (1–x) (0.75Agl0.25AgCl)xAl₂O₃ are reported. Undried Al₂O₃ particles of size <10 m were used. The conventional matrix material Agl has been replaced by a new mixed 0.75Agl0.25AgCl quenched and/or annealed host compound. Conductivity enhancements 10 from the annealed host and 3 times from the quenched host obtained for the composition 0.7(0.75Agl0.25AgCl)0.3Al₂O₃, can be explained on the basis of the space charge interface mechanism. Direct measurements of ionic mobility as function of temperature together with the conductivity were carried out for the best composition. Subsequently, the mobile ion concentration n values were calculated from and a data. The value of heat of ion transport q* obtained from the plot of thermoelectric power versus 1/T supports Rice and Roth's free ion theory for superionic conductors. Using the best composition as an electrolyte various solid state batteries were fabricated and studied at room temperature with different cathode preparations and load conditions.     

A precipitate phase in AA2124

A new precipitate phase (designated X phase) other than the S(Al₂CuMg) precipitate phase has been discovered in the 2124 aluminium alloy. Using selected-area electron diffraction analysis, dynamical diffraction simulation, energy dispersion analysis of X-rays and high-resolution electron microscopy, it is suggested that the X phase has an orthorhombic crystal structure witha=0.492 nm,b=0.852 nm andc=0.701 nm. The space group of the phase is Cmmm. There are 10 atoms in a cell with AlCuMg=244. The orientation relationship between the X phase and the matrix is determined as (1–10)_m(010)_x, [–1–1–1]_m [001]_x.     

Preparation of superconducting Bi-Sr-Ca-Cu-O ceramics by the sol-gel method

Superconducting Bi-(Pb)-Sr-Ca-Cu-O ceramics were prepared through the sol-gel method using an aqueous solution of metal acetates containing acetic acid and tartaric acid. The conditions of gelation and conversion of gel to Bi₂Sr₂CaCu₂O_x phase were studied by thermal analysis, infrared absorption spectroscopy and X-ray diffraction technique. It was found that transparent gels were obtained from the solutions containing tartaric acid, with a molar ratio of C₄H₆O₆/Cu of about 0.4. The gel matrix was assumed to be composed of carboxylate anions and metal cations. A gel of molar composition BiSrCaCu = 2223 was decomposed to CaCO₃, CaO, CuO and Bi_1-x Sr_xO_y (x = 0.2 to 0.3) at low temperatures of 270 to 600 ° C and produced Bi₂Sr₂CaCu₂O_x phase at 800 ° C via complex intermediate states. A rapid cooling of the heated product increasedT _c (end) in the gel of molar composition BiSrCaCu = 2223, while a slow cooling increasedT _c (end) in the lead-containing gel of molar composition BiPbSrCaCu = 1.850.351.92.03.1. The latter showedT _c (onset) at 115 K andT _c (end) at 105K.     

The origins of mullite formation

The evolution of mullite formation has been studied from Al₂O₃-SiO₂ gels. The studies have established (a) the identity of the controversial cubic phase, (b) the chemical, structural and compositional continuity in the evolution of mullite formation, (c) the existence of solid solutions between (32) and (21) mullites, (d) the origins of the exotherms, and (e) the origins of mullite formation. The Al-Si spinel has a composition and structure similar to that of the (21) mullite, i.e. _x Al_16-x ^vi[Al _x Si_4-x ]^ivO₃₂.     

Distribution of α-AlFeSi and β-AlFeSi particles in surface layer of AA6063 alloy billets after heat treatment

We developed the EPMA mapping method of small -AlFeSi(Al_8.3Fe₂Si) and -AlFeSi(Al_8.9Fe₂Si₂) particles in the billets of Al-Mg-Si alloys such as AA6063 alloys. To discriminate between -AlFeSi and -AlFeSi particles we used the relative X-ray intensities of Fe/Si ratio, the I _Fe/I _Si ratio, instead of the Fe/Si mass ratio. To obtain the I _Fe/I _Si ratio, we used a Monte Carlo method. In this study, using this method the mapping of -AlFeSi and -AlFeSi particles in the surface layer of AA6063 billets after the heat treatment (for 2 h at 580°C) was done. Namely, the distribution of -AlFeSi and -AlFeSi particles of zones from the billet surface to a depth of 800 m was measured. Results showed the zone from the surface to a depth of 200 m was occupied mainly by -AlFeSi particles and the zone from a depth of 200 m toward the center was occupied mainly by -AlFeSi particles. From these results, it was found that if we remove zones from the surface to a depth of 200 m, we can remove the majority of the -AlFeSi particles, and thus improve the quality of anodizing performance of Al-Mg-Si alloys extrusions.     

Phase decomposition of liquid-quenched β-type Ti-Cr alloys

Phase decomposition behaviour of liquid-quenched (bcc) type Ti-Cr alloys was investigated by means of transmission electron microscopy and hardness measurements. It was found that decomposition of to ₁ (Ti-rich, bcc) + ₂ (Ti-lean, bcc) takes place in the intermediate composition range of the Ti-Cr system. This experimental result proves the theoretical prediction made by Menon and Aaronson, but the observed ₁ + ₂ two-phase field expands towards higher temperatures than the predicted binodal line. The coherent ₁ + ₂ two-phase state exhibits the so-called 100 modulated structure and it was concluded that the formation of such a structure is a result of spinodal decomposition of the -phase. We obtained time-temperature-transformation (TTT) diagrams of -type Ti-30, 40 and 50 at % Cr alloys. A typical sequence of structural change is coherent ₁ + ₂ incoherent ₁ + ₂ incoherent ₁ + ₂ + grain boundary precipitates stable state of + TiCr₂ or + TiCr₂. Not all the states in the above sequence appear, depending on alloy composition, liquid-quenching rate and ageing temperature.     

Thermal conductivity of hydrocarbons in the naphthene group under high pressures

The thermal conductivity of hydrocarbons in the naphthene group has been experimentally determined. An equation is now proposed for calculating the thermal conductivity over the given temperature and pressure ranges.Notation thermal conductivity - ₂₀ and ₃₀ values of the thermal conductivity at 20 and 30°C, respectively - t₀,P₀ thermal conductivity at t₀, p₀ - _t p thermal conductivity at temperature t and under pressure P - change in thermal conductivity - P pressure - P_melt melting pressure - P₀ atmospheric pressure - t₀ 20°C temperature - T, t temperature - T_cr critical temperature - temperature coefficient of thermal conductivity - ₂₀ temperature coefficient of density - density - ₂₀ density at 20°C - _cr critical density - M molar mass - =T/T_cr referred temperature - v specific volume - v₀ specific volume at 20°C - v change in specific volume - _{3 0} a coefficient - B (t) a function of the temperature - S a quadratic functional - W_i, weight of the i-th experimental point - _i error of the i-th experimental value of thermal conductivity - B _{y, =0.6} value of B (t) at T = 0.6T_cr - B = B (t)/B_{, =0.6} referred value of coefficient B (t) Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 491–499, September, 1981.     

Development of solidification microstructures in a fibre reinforced alloy

The solidification behaviour of a fibre reinforced Al-6 wt% Cu alloy, containing 30 vol% of 3 m diameter, semi-continuous, aligned alumina fibres has been studied. Results are presented to show the influence of fibres on the microstructural development of and microsegregation in the matrix during freezing. The effect of total solidification time, _t, on solidification behaviour was examined for 1<_t<520 S. By using interrupted solidification experiments microstructural development was studied in detail. It was found that -Al begins to grow within interfibre regions, and grows towards the Al₂O₃ fibres, avoiding them where possible. Consequently fibres are located in the last regions to solidify. When _t>10 s the final microstructure is non-dendritic, and CuAl₂ is located predominantly at the fibre-matrix interface. When _t 1 s it was observed that the final microstructure is dendritic with a periodic segregation pattern, and the CuAl₂ is more dispersed. The matrix composition becomes more uniform, and the minimum matrix composition rises as _t increases. The growth and microsegregation are analysed and discussed using simple semi-analytical models. The implications are that fibres significantly influence solidification behaviour if _f/_s<1, where _f is the average interfibre spacing and _s the secondary dendrite arm spacing which would develop in the unreinforced alloy.     

Mössbauer studies of α″-Fe16N2 and α′-Fe8N films

Conversion-electron Mössbauer spectra of epitaxial -Fe₁₆N₂ and -Fe₈N films have been studied and their differences are discussed in detail. The Mössbauer spectrum of -Fe₁₆N₂ can be decomposed into three subspectra, which correspond to the 4d, 8h and 4c sites. The Mössbauer spectrum of -Fe₈N can be fitted using four spectra based on a nitrogen-atom-random-distribution model. The average hyperfine field is larger (3%) for -Fe₁₆N₂ than for -Fe₈N, which is approximately consistent with a 4.1% enhancement of the magnetic moments for -Fe₁₆N₂. The iron moments tend to locate in the film plane for -Fe₁₆N₂ and to arrange perpendicularly to the film plane for -Fe₈N.     

The influence of ageing on the stability of β-γ/γ′ derived microstructures in Ni-Al-Cr-(Co) alloys

Multiphase Ni-Al-(Fe)-(Cr)-(Co)-based intermetallics with (B2)- (A1)/(L1₂), - or - microstructures can exhibit significant room-temperature tensile ductility. In the case of Ni-Al-Cr-based alloys, microstructural development is complicated by the precipitation of -Cr, which can supplant the -phase during ageing of three-phase -/ microstructures. An investigation of the stability, during ageing, of cast Ni-Al-Cr-(Co) alloys with microstructures derived from -/ is reported. In the as-cast condition, the materials investigated consisted of a dendritic matrix containing L1₀ type martensite and interdendritic /. Extensive intra- and interdendritic -Cr precipitation was also observed. The stability during ageing of the interdendritic / microstructure is also considered and transformation of the L1₀ martensite is examined.     

Low-temperature synthesis,pyrolysis and crystallization of tantalum oxide gels

Tantalum oxide gels in the form of transparent monoliths and powders have been prepared from hydrolysis of tantalum pentaethoxide under controlled conditions using different mole ratios of Ta(OC₂H₅)₅C₂H₅OHH₂OHCl. Alcohol acts as the mutual solvent and HCl as the deflocculating agent. For a fixed alkoxide water HCl ratio, the time of gel formation increased with the alcohol to alkoxide molar ratio. Thermal evolution of the physical and structural changes in the gel has been monitored by differential thermal analysis, thermogravimetric analysis, X-ray diffraction, and infrared spectroscopy. On heating to 400 °C, the amorphous gel crystallized into the low-temperature orthorhombic phase -Ta₂O₅, which transformed into the high-temperature tetragonal phase -Ta₂O₅ when further heated to 1450 °C. The volume fraction of the crystalline phase increased with the firing temperature. The -Ta₂O₅ converted back into the low-temperature phase, -Ta₂O₅, on slow cooling through the transformation temperature of 1360 °C, indicating a slow but reversible transformation.     

Universal simulation of degenerating homogeneous turbulence

The problem of universal simulation of the dynamics of a turbulent velocity field (universal in the sense of arbitrary values of the Reynolds turbulence number) is treated on the basis of the moment model in the second approximation.Notation ¯q² _i ² double the kinetic turbulence energy - _u ² =5v¯q²/_u Taylor turbulence scale squared - _u=v1/x_k)²> kinetic-energy dissipation function - N_Re,=¯q²_u / Reynolds turbulence number Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 42, No. 1, pp. 46–52, January, 1982.     

Ageing characteristics of Al-2.5% Li rapidly solidified alloy

The present work was performed on an Al–2.5 wt% Li alloy produced by melt spinning. The ribbons were aged in the temperature range 180 to 310° C for times between 1 min and 120h. The kinetics of coarsening of (Al₃Li) and (AlLi) phase particles were investigated using transmission electron microscopy and hardness measurements. The results show that coarsening of (Al₃Li) follows a simple linear relation with the cube root of Me, whereas coarsening of (AlLi) does not follow the same trend. We believe that the (AlLi) phase nucleates at the (Al₃Li)/matrix interface and grows by the dissolution of the nearby (Al₃Li) particles. The mechanical properties of the powder metallurgy alloy show that a large volume fraction of PFZ contributes to the alloy ductility, 11 %, in the aged condition. Also, the yield strength is greatly improved due to refinement effects enhanced by rapid solidification.     

Breakup of an anomolously viscous liquid film in a centrifugal force field

An equation is obtained for the breakup radius with consideration of tipping moments and Laplacian pressure forces acting on the liquid ridge at the critical point.Notation K, n rhenological constants - density - surface tension - r current cup radius - R maximum cup radius - r_c critical radius for film breakup - ¯r=¯r=r/R dimensionless current radius - ¯r_c=r_c/R dimensionless critical radius - ₀, _c actual and critical film thicknesses - current thickness - R_r ridge radius - h₀ ridge height - h current ridge height - ₀ limiting wetting angle - current angle of tangent to ridge surface - angle between axis of rotation and tangent to cup surface - angular velocity of rotation - q volume liquid flow rate - v₁ and v meridional and tangential velocities - =4vv _lm/r,=4v_m/r dimensionless velocities - M moments of surface and centrifugal forces - M_v moment from velocity head - p_r pressure within ridge - P_vm pressure from velocity head - p_m, p_pm pressures from centrifugal force components tangent and normal to cup surface - deviation range of breakup radius from calculated value - ¯r_max, ¯r_min limiting deviations of breakup radius - _c angle of tangent to curve _c/°₀=f(¯r) at critical point - t random oscillation of ratio _c/_c Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 1, pp. 51–56, July, 1980.     

Intensity of critical opalescence of helium-4

We present measurements of the critical opalescence of helium-4. The results are analyzed by the Einstein and Ornstein-Zernike theory and the power laws. We obtain ==1.17±0.02, ==0.62±0.1,/=4.5±0.3,P _c =1706.008 mm Hg, andT _c =5,189.863 mK (T ₅₈ ). The critical behavior of helium-4 is almost the same as that of classical fluids and the influence of the quantum nature of helium-4 is not as evident as has been claimed.     

Thermodynamic properties of the superconductorsBaPb 0.7 Bi 0.3 O 3 andBa 0.7 K 0.3 BiO 3 using Eliashberg theory

We present results of a thermodynamic analysis for the superconductors compounds BaPb_0.7Bi_0.3O₃ and Ba_0.7K_0.3BiO₃. The physical quantities are calculated making use of the Eliashberg theory and the electron-phonon spectra ²()F() as calculated by Shirai et al. For the superconductor BaPb_0.7Bi_0.3O₃, several models of the ²()F() were studied looking for a better agreement with experimental data. The best fit is achieved with a simple constant scaling (C = 1.25) of the Shirai's spectra. The functional derivative of the deviation function D(t) with respect to changes in ²()F() is also calculated.     

Surface nucleation and cellular growth kinetics of cordierite glass ceramics containing 3 mol % Y2O3-ZrO2

Cordierite-based glass ceramics of the 2MgO2Al₂O₃5SiO₂ composition with t-ZrO₂ (3 mol% Y₂O₃-ZrO₂) and P₂O₅ addition, was heat-treated isothermally and isochronically for crystallization studies. Major crystalline phases incurred by the heat treatment were t-ZrO₂ and -cordierite. Surface nucleation predominated when edge and corner nucleation in these samples were suppressed regardless of their radii of curvature. Crystallization began with the formation of -quartz S.S. and its transformation to -cordierite was followed by prolonged heating. Cellular growth of -cordierite on the surface of the quenched glass plates, gave a linear kinetics. The activation energy for cellular growth was 410 kJ mol^–1.     

Effect of Grain Size on the Modulus of Elasticity and Strength of Synthetic Graphites

The effect of the grain size of the filler on the mechanical properties (compressive, bending, and tensile strength and modulus of elasticity) of synthetic graphite is analyzed using data for commercial structural graphites. As the mean particle size of the filler (_av) decreases from 3000 to 1 m, the modulus of elasticity increases, on the average, from 10 to 15 GPa, and the compressive, bending, and tensile strength increases by about one order of magnitude. The Griffith equation is used to evaluate the size of defects that initiate fracture (c _c) in different types of graphites. It is shown that the factors determining the critical defect size depend on the particle size of the filler. For _av > 150 m, c _c is comparable to _av or _max. In the range 30 < _av < 150 m, c _c is equal to or greater than _max. In graphites with _av < 30 m, c _c far exceeds _max and, presumably, corresponds to the particle size of the molding powder.     

High-frequency dielectric properties of Mg-Al-Si,Ca-Al-Si and Y-Al-Si oxynitride glasses

Recently developed coaxial line techniques [1] have been used to determine, at room temperature, the values of the real () and imaginary (') parts of the dielectric constants for some Mg-Al-Si, Ca-Al-Si and Y-Al-Si oxynitride glasses over the frequency range 500 MHz to 5 GHz. The frequency dependencies of and ' are consistent with the universal law of dielectric response in that (-_t8)^(n–1) and '^(n–1) for all glass compositions; the high experimental value of the exponent (n=1.0±0.1) suggests the limiting form of lattice loss [2] situation. In this frequency range, as previously reported [3] at longer wavelengths, the addition of nitrogen increases the dielectric constant, (); in both the oxide and oxynitride glasses is also influenced by the cation, being increased with cation type in the order magnesium, yttrium, calcium as at lower frequencies.     

Effect of AlN and Al2O3 additions on the phase relationships and morphology of SiC Part I Compositions and properties

X-ray diffraction was utilized to follow the transformation from -SiC (3C) to the various -SiC polytypes in the presence of AlN and Al₂O₃ additives after hot pressing from 1700 to 2100°C. The 2H- and 6H-polytypes of -SiC were the predominate polytypes with additions of only AlN or Al₂O₃, respectively. The amount of 2H- and 6H-polytypes, and subsequently the microstructural morphology of the SiC materials, were found to be controlled by varying the amount of AlN and Al₂O₃. Improvements in fracture toughness to 9 MPa-m were achieved with flexural strengths ranging from 600 to 900 MPa. These results suggest that accurate control of the polytypic make-up of SiC-based materials, along with their mechanical properties, can be achieved through AlN and Al₂O₃ additions.