Adsorption characteristics and separation of Cr(III) and Cr(VI) on hydrous titanium(IV) oxide

A hydrous titanium(IV) oxide was prepared to study the adsorption characteristics and the separation of chromium species. Batch sorption studies have been carried out to determine the effect of pH on the sorption of Cr(III) and Cr(VI) on hydrous TiO2. An excellent separation efficiency of Cr(III) and Cr(VI) was obtained at pH 2. The adsorption percentage of Cr(VI) was above 99%, whereas that of the Cr(III) was less than 1% at this pH. The adsorption isotherm of Cr(VI) on hydrous TiO2 at pH 2 was in good agreement with the Langmuir isotherm. The maximum adsorption capacity of Cr(VI) on TiO2 was 5 mg g(-1). The rate of adsorption of Cr(VI) by hydrous TiO2 with average particle diameter 250 and 500 microm has been studied under particle diffusion controlled conditions. The diffusion coefficients of Cr(VI) for both hydrous TiO2 having average particle diameter of 250 and 500 microm was calculated at pH 2 as 3.84 x 10(-10) m2 s(-1) and 8.86 x 10(-10) m2 s(-1), respectively.     

Synthesis of Cr(VI)-imprinted poly(4-vinyl pyridine-co-hydroxyethyl methacrylate) particles: its adsorption propensity to Cr(VI)

The aim of this study is to prepare ion-imprinted polymers, which can be used for the selective removal of Cr(VI) anions from aqueous media. 4-Vinyl pyridine (4-VP) was used as functional monomer. The Cr(VI)-imprinted poly(4-vinyl pyridine-co-2-hydroxyethyl methacrylate), poly(VP-HEMA), particles were prepared by bulk polymerization. The Cr(VI)-imprinted polymer particles were grained from the bulk polymer, and the template ions (i.e., Cr(VI)) were removed using thiourea (0.5%, v/v) in 0.5M HCl. The Cr(VI)-imprinted polymer contained 21.4 μmol 4-VP/g polymers. The specific surface area of the IIP2 particles was found to be 34.5m(2)/g (size range of 75-150 μm), and the swelling ratio was about to 108%. The effect of initial concentration of Cr(VI) anions, the adsorption rate and the pH of the medium on adsorption capacity of Cr(VI)-imprinting polymer were studied. The maximum experimental adsorption capacity was 3.31 mmol Cr(VI)/g polymer. Under competitive condition, the adsorption capacity of Cr(VI)-imprinted particles for Cr(VI) is 13.8 and 11.7 folds greater than that of the Cr(III) and Ni(II) ions, respectively. The first- and second order kinetics models were estimated on the basis of comparative analysis of the corresponding rate parameters, equilibrium capacity and correlation coefficients. The Langmuir adsorption isotherm model was well described the Cr(VI)-imprinted system and the maximum adsorption capacity (Q(max)) was found to be 3.42 mmol/g. Moreover, the reusability of the poly(VP-HEMA) particles was tested for several times and no significant loss in adsorption capacity was observed.     

Adsorption of Cr(VI) from aqueous solution by hydrous zirconium oxide

A type of ZrO₂·nH₂O was synthesized and its Cr(VI) removal potential was investigated in this study. The kinetic study, adsorption isotherm, pH effect, thermodynamic study and desorption were examined in batch experiments. The kinetic process was described by a pseudo-second-order rate model very well. The Cr(VI) adsorption tended to increase with a decrease of pH. The adsorption data fitted well to the Langmuir model. The adsorption capacity increased from 61 to 66 mg g^?1 when the temperature was increased from 298 to 338 K. The positive values of both ΔH° and ΔS° suggest an endothermic reaction and increase in randomness at the solid–liquid interface during the adsorption. ΔG° values obtained were negative indicating a spontaneous adsorption process. The effective desorption of Cr(VI) on ZrO₂·nH₂O could be achieved using distilled water at pH 12.     

Adsorption of Cr(VI) from aqueous solutions by spent activated clay

Adsorption of Cr(VI) onto spent activated clay (SAC), a waste produced from an edible oil refinery company, was investigated for its beneficial use in wastewater treatment. After pressure steam treatment, SAC was used as an adsorbent. The adsorption kinetic data were analyzed and fitted well in a pseudo-first-order equation and the rate of removal was found to speed up with decreasing pH and increasing temperature. Activation energy for the adsorption process was found to be 4.01–5.47 kcal/K mol. The Langmuir adsorption isotherm was used to fit the equilibrium data and the effect of pH, temperature and ionic strength were studied. The maximum adsorption capacities for Cr(VI) ranged from 0.743 to 1.422 mg/g for temperature between 4 and 40 °C under a condition of pH 2.0. The studies conducted show the process of Cr(VI) removal to be spontaneous at high temperature and endothermic in nature. From the waste utilization and environment point of view, the work carried out is important and useful. Results obtained can serve as baseline data for designing a treatment process using this low-cost adsorbent for the treatment of wastewater rich in Cr(VI).     

Adsorption of Cr(VI) using silica-based adsorbent prepared by radiation-induced grafting

Silica-based adsorbent was prepared by radiation-induced grafting of dimethylaminoethyl methacrylate (DMAEMA) onto the silanized silica followed by a protonation process. The FTIR spectra and XPS analysis proved that DMAEMA was grafted successfully onto the silica surface. The resultant adsorbent manifested a high ion exchange capacity (IEC) of ca. 1.30 mmol/g and the Cr(VI) adsorption behavior of the adsorbent was further investigated, revealing the recovery of Cr(VI) increased with the adsorbent feed and the equilibrium adsorption could be achieved within 40 min. The adsorption capacity, strongly depended on the pH of the solution, reached a maximum Cr(VI) uptake (ca. 68 mg/g) as the pH was in the range of 2.5–5.0. Furthermore, even in strong acidic (4.0 mol/L HNO₃) or alkaline media (pH 11.0), the adsorbent had a sound Cr(VI) uptake capacity (ca. 22 and 30 mg/g, respectively), and the adsorption followed Langmuir mode. The results indicated that this adsorbent, prepared via a convenient approach, is applicable for removing heavy-metal-ion pollutants (e.g. Cr(VI)) from waste waters.     

离子液体改性沸石吸附水溶液中Cr(VI)的研究

利用离子液体十六烷基-3-甲基咪唑氯化物对天然沸石进行表面改性,并将改性沸石用于水中Cr(VI)的吸附,研究离子液体浓度、反应时间、p H等条件对Cr(VI)吸附性能的影响,采用X射线衍射和红外光谱对离子液体改性沸石进行表征。结果表明,咪唑离子浓度不大于0.3 mol/L的低浓度离子液体改性的沸石对Cr(VI)的吸附作用不明显,咪唑离子浓度大于0.9 mol/L的离子液体改性的沸石对Cr(VI)具有好的吸附效果;酸性条件有利于改性沸石对Cr(VI)的吸附;咪唑离子浓度为0.6、0.9 mol/L的离子液体改性的沸石吸附Cr(VI)平衡的时间分别为240、8 min。     

吸附温度对MgAl金属氧化物微观结构和吸附Cr(VI)性能的影响

研究了MgAl水滑石(LDH)焙烧产物(LDO)对Cr(VI)的吸附性能。考察了吸附温度对LDO吸附性能的影响, 研究了吸附过程的热力学和动力学行为。结合XRD和FT-IR表征, 阐明其吸附机理。结果表明, CrO₄^2–已成功插入水滑石层间, 适当提高吸附温度有利于LDO恢复LDH晶相。在20~60℃范围内, 随吸附温度升高, LDO对Cr(VI)吸附量增大, 50~60℃时, Cr(VI)吸附量为91 mg/g。Cr(VI)的吸附平衡数据符合Langmuir模型方程, ΔG_o为负值说明吸附过程为自发过程, ΔS_o和ΔH_o为正值表明吸附为熵增的吸热过程。吸附动力学符合伪二级动力学模型, LDO 的吸附活化能为20.04 kJ/mol, 表现为扩散控制的活性化学吸附过程。     

Adsorption of Cr(VI) from synthetic solutions and electroplating wastewaters on amorphous aluminium oxide

The adsorption behaviour of amorphous aluminium oxide was studied with respect to Cr(VI) in order to consider its application to purify electroplating wastewaters. A batch method was employed using Cr(VI) concentrations ranged from 10 to 200mg/l. The Langmuir model was found to describe the adsorption process well, offering a maximum adsorption capacity of 78.1mg/g. The effect of ionic strength (0-0.1M KNO(3)), pH (3-9) and competitive solutes (molar ratio [Cr(VI)]/[SO(4)(2-)]=1 and 100) on the retention process was evaluated. Cr(VI) adsorption on amorphous aluminium oxide appeared to be dependent on ionic strength with a more pronounced effect in acid conditions. Conversely, adsorption was not affected by pH in acid medium, but decreased when pH sifted to alkaline values. The presence of SO(4)(2-) greatly reduced Cr(VI) removal across the entire pH range when both solutes were present in similar concentrations. Amorphous aluminium oxide also showed a high adsorption capacity when used in the purification of Cr(VI) electroplating wastewaters. The adsorbent doses required to attain more than 90% of Cr(VI) removal varied between 1 and 5 g/l depending on Cr(VI) concentration in wastewaters.     

磺化褐煤对废水中Cr(Ⅵ)离子的吸附与还原

在静态条件下,进行了以磺化褐煤(SBC)作吸附剂、还原剂净化含铬废水的实验。研究了含铬废水的pH值、浓度和接触时间等因素对SBC吸附、还原Cr(Ⅵ)的影响,确定了SBC净化含铬废水的最佳条件。结合对实际含Cr(Ⅵ)废水的吸附、还原净化处理,讨论了SBC对电镀废水处理的可行性     

磺化褐煤对废水中Cr（Ⅵ）离子的吸附原与还原

在静态条件下，进行了以磺化褐煤作吸附剂、还原剂净化含铬铬废水的实验。研究了含铬废水的ＰＨ值、浓度和接触时间等因素对ＳＢＣ吸附、还原Ｃｒ（Ⅵ）的影响，确定了ＳＢＣ将化含铬废水的最佳条件。结合对实际含Ｃｒ（Ⅵ）废水的吸附、还原净化处理，讨论了ＳＢＣ对电镀废水处理的可行性。     

The effectiveness of four organic matter amendments for decreasing resin-extractable Cr(VI) in Cr(VI)-contaminated soils

This paper compared the effectiveness of four organic materials for decreasing the amounts of soil extractable Cr(VI) in Cr(VI)-contaminated soils using the DOWEX M4195 resin-extraction method. Organic matters were added into Cr(VI)-spiked soils [500 mg Cr(VI)(kgsoil)(-1)] in the form of sugarcane dregs compost (SCDC), cattle-dung compost (CDC), soybean meal (SBM) and rice bran (RB), in the amounts of 0, 1%, and 2% by dry weight, respectively. The results indicated that adding only 1% organic matter to the studied soils could effectively decrease the amount of soil resin-extractable Cr(VI) after 12 days of incubation. The decrease of resin-extractable Cr(VI) by organic materials was mainly the result from the reduction of Cr(VI) to Cr(III) supported by the XANES spectroscopy. Among the four tested organic materials, SBM and RB had higher effectiveness in decreasing soil resin-extractable Cr(VI) than CDC and SCDC. This result may be due to the fact that SBM and RB have more dissolved organic carbon (DOC) and protein than CDC and SCDC. Therefore, it was concluded that the contents of DOC and protein are the main factors that determine the effectiveness of organic materials for decreasing the amounts of soil available Cr(VI) in Cr(VI)-contaminated soils.     

提取腐植酸后的天祝褐煤残渣对污水中Cr(VI)的吸附性能

天祝褐煤资源丰富,其提取腐植酸后的残渣对污水中的有害物质有一定的吸附能力。为此,制备了天祝褐煤提取腐植酸后的残渣,研究了其对污水中重金属离子Cr(Ⅵ)的吸附性能。结果表明:在室温(20～25℃),pH值为5的条件下,褐煤残渣对Cr(VI)有较好的吸附性能,吸附平衡时间约为4h;吸附规律符合Freundlich吸附等温式,其相关系数R2为0.9686,特性常数n为2.0446,其吸附过程可用Ho准二级反应动力学模型描述。     

Bioremediation of Cr(VI) in contaminated soils

Ex situ treatment of hexavalent chromium (Cr(VI)) contaminated soil using a bioreactor-biosorption system was evaluated as a novel remediation alternative. Leaching of Cr(VI) from the contaminated soil using various eluents showed that desorption was strongly affected by the solution pH. The leaching process was accelerated at alkaline conditions (pH 9). Though, desorption potential of ethylene diamine tetra acetic acid (EDTA) was the maximum among various eluents tried, molasses (5 g/L) could also elute 72% of Cr(VI). Cr(VI) reduction studies were carried out under aerobic and facultative anaerobic conditions using the bacterial isolates from contaminated soil. Cr(VI) reduction was moderately higher in aerobic conditions than in facultative anaerobic conditions. The effect of various electron donors on Cr(VI) reduction was also investigated. Among five electron donors screened, peptone (10 g/L) showed maximum Cr(VI) reduction followed by molasses (10 g/L). The time required for complete Cr(VI) reduction was increased with increase in the initial Cr(VI) concentration. However, specific Cr(VI) reduction was increased with increase in initial Cr(VI) concentration. Sulfates and nitrates did not compete with Cr(VI) for accepting the electrons. A bioreactor was developed for the detoxification of Cr(VI). Above 80% of Cr(VI) reduction was achieved in the bioreactor with an initial Cr(VI) concentration of 50 mg/L at an HRT of 8 h. An adsorption column was developed using Ganoderm lucidum (a wood rooting fungus) as the adsorbent for the removal of trivalent chromium (Cr(III)) and excess electron donor from the effluent of the bioreactor. The specific Cr(III) adsorption capacity of G. lucidum in the column was 576 mg/g. The new biosystem seems to be a promising alternative for the ex situ bioremediation of Cr(VI) contaminated soils.     

Cr(VI) and Cr(III) speciation on Bacillus sphaericus loaded diaion SP-850 resin

A speciation procedure for chromium(III) and chromium(VI) in the environmental samples has been established in the presented work. The procedure presented based on quantitative biosorption of chromium(III) on Bacillus sphaericus loaded Diaion SP-850 at pH 5. The Cr(VI) recoveries at pH 5 were below 5% on the biosorbent. After reduction of Cr(VI) by concentrated H(2)SO(4) and ethanol, the system was applied to the total chromium. Cr(VI) was calculated as the difference between the total chromium content and the Cr(III) content. Optimal analytical conditions including pH, amounts of biosorbent, etc. for Cr(III) recoveries were investigated. The influences of the some alkaline and earth alkaline ions and some transition metals on the recoveries were also investigated. The capacity of biosorbent for chromium(III) was 6.95 mgg(-1). The detection limit (3 sigma) of the reagent blank for chromium(III) was 0.50 microgL(-1). The procedure was successfully applied to the speciation of chromium(III) and chromium(VI) in natural water samples (R.S.D. lower than 5%, recoveries greater than 95%).     

Mathematical models applied to the Cr(III) and Cr(VI) breakthrough curves

Trivalent and hexavalent chromium continuous biosorption was studied using residual brewer Saccharomyces cerevisiae immobilized in volcanic rock. The columns used in the process had a diameter of 4.5 cm and a length of 140 cm, working at an inlet flow rate of 15 mL/min. Breakthrough curves were used to study the yeast biosorption behavior in the process. The saturation time (ts) was 21 and 45 h for Cr(III) and Cr(VI), respectively, and a breakthrough time (tb) of 4 h for Cr(III) and 5 h for Cr(VI). The uptake capacity of the biosorbent for Cr(III) and Cr(VI) were 48 and 60 mg/g, respectively. Two non-diffusional mathematical models with parameters t0 and sigma were used to adjust the experimental data obtained. Microsoft Excel tools were used for the mathematical solution of the two parameters used.     

The effectiveness of ferrous iron and sodium dithionite for decreasing resin-extractable Cr(VI) in Cr(VI)-spiked alkaline soils

Ferrous iron, Na(2)S(2)O(4), and a mixture of Fe(II) and Na(2)S(2)O(4) (4:1 mol/mol) were tested for their effectiveness for decreasing resin-extractable Cr(VI) in alkaline Cr(VI)-spiked soils. The results indicated that adding those reductants greatly decreased the amount of resin-extractable Cr(VI) when the application rate of reductants equaled the number of equivalents of dichromate added to the Cr(VI)-spiked soils. This was mainly as a result of the Cr(VI) reduction into Cr(III), as supported by the XANES spectra. Among the tested reductants, a mixture of Fe(II) and Na(2)S(2)O(4) was the most effective to decrease resin-extractable Cr(VI). The extent to which resin-extractable Cr(VI) and soil pH were decreased was affected by the pH of the reductants. Among the tested reductants at various pH, FeSO(4) at pH below 1 was the most effective in decreasing resin-extractable Cr(VI) in alkaline soils. However, the soil pH was the most decreased as well. On the other hand, the mixtures of ferrous iron and dithionite at a wide range of pH were all efficient (>70% efficiency) in decreasing resin-extractable Cr(VI). Moreover, the extent of the decrease in soil pH was much smaller than that by FeSO(4) (pH<1) alone, and thus the possibility of the Cr(III) hazard can be avoided.     

Speciation of Cr(III) and Cr(VI) after column solid phase extraction on Amberlite XAD-2010

A speciation procedure for Cr(III) and Cr(VI) based on column solid phase extraction on Amberlite XAD-2010 and flame atomic absorption spectrometry combination. Cr(VI) was quantitatively recovered on Amberlite XAD-2010 resin at pH range of 2.0-3.0 as its diethyldithiocarbamate complex, while the recoveries of Cr(III) was below 5%. The influences of the various parameters including amounts of the reagents, eluent type and its volume, sample volume, etc., on the quantitative recoveries were examined. The interference of matrix and coexistent elements for method were studied. The detection limit (corresponding to three times the standard deviation of the blank) and the enrichment factor for Cr(VI) were found to be 1.28 microg/L and 25, respectively. To verify the accuracy of the method, drinking water certified reference material (CRM-TMDW-500) was analyzed and the results obtained were in good agreement with the certified value. The proposed method has been successfully applied to the speciation of Cr(III) and Cr(VI) in water samples and preconcentration of total chromium in environmental samples.     

Cr(VI) reduction in aqueous solutions by siderite

Hexavalent chromium is a common and toxic pollutant in soils and wastewaters. Reduction of the mobile Cr(VI) to less mobile and less toxic Cr(III) is a solution for decontamination of industrial effluents. In this study, the reduction of hexavalent chromium in aqueous solutions by siderite was investigated. The influences of amount of acid, contact time, siderite dosage, initial Cr(VI) concentration, temperature and particle size of siderite have been tested in batch runs. The process was found to be acid, temperature and concentration dependent. The amount of acid is the most effective parameter affecting the Cr(VI) reduction since carbonaceous gangue minerals consume acid by side reactions. The highest Cr(VI) reduction efficiency (100%) occurred in the 50 mg/l Cr(VI) solution containing two times acid with respect to stoichiometric amount of Cr(VI) and at the conditions of siderite dosage 20 g/l, contact time 120 min and temperature 25 degrees C. Reduction efficiency increased with increase in temperature and decrease in particle size. The reduction capacity of siderite was found to be 17 mg-Cr(VI)/g.     

Speciation of Cr(III) and Cr(VI) in environmental samples by solid phase extraction on Ambersorb 563 resin

A simple and sensitive method for the speciation, separation and preconcentration of Cr(VI) and Cr(III) in natural water, soil and sediment samples was developed. Cr(VI) has been separated from Cr(III) and preconcentrated as Cr(III)-diphenylcarbazone complex by using Ambersorb 563 resin and determined by spectrophotometric method at 540 nm. Effect of analytical parameters such as sulfuric acid concentration, ligand volume, type of elution solution, sample volume, amount of resin and foreign ions were investigated. The presented procedure was successfully applied for the chromium speciation in various environmental samples with successfully results.     

Extent of oxidation of Cr(III) to Cr(VI) under various conditions pertaining to natural environment

Calculations show that oxidation of chromium oxide (Cr2O3) by oxygen and oxidation of chromium hydroxide (Cr(OH)3) by manganese dioxide (MnO2) are thermodynamically feasible in both aerobic and mildly anoxic environments. Experiments were carried out to determine the rate and extent of chromium oxidation under various conditions, i.e., when Cr2O3 was heated in the presence of oxygen, when Cr(OH)3 and MnO2 mixtures were suspended in aerobic or anoxic aqueous media at various pH values, when Cr(OH)3 and MnO2 mixtures interacted in moist aerobic conditions and when chromium assumed to be Cr(OH)3 and manganese assumed to be MnO2 interacted in the presence of competing electron donors/acceptors, as is the case in chromium-contaminated sludge. Results indicate that trivalent chromium in Cr2O3 could be readily converted to hexavalent chromium at a temperature range of 200-300 degrees C, with conversion rates of up to 50% in 12 h. In aqueous media, Cr(OH)3 was slowly converted to dissolved Cr(VI) in the presence of MnO2, both in aerobic and anoxic conditions, with conversion rates of up to 1% in 60 days. In moist aerobic conditions and in the presence of MnO2, Cr(OH)(3) slowly converted to hexavalent chromium, with up to 0.05% conversion observed in 90 days. Chromium oxidation also occurred in sludge samples, especially under aerobic conditions. However, such transformation was found to be transitory, with the Cr(VI) formed being ultimately reduced back to Cr(III) due to the presence of various reducing agents in the sludge. Nevertheless since up to 17% conversion of Cr(III) to Cr(VI) occurred in sludge under aerobic conditions by 30 days, there is real danger under field conditions of spreading Cr(VI) pollution due to possible intervening rainfall, runoff and percolation.