Tribological properties of metal-plastic multilayer composites under oil lubricated conditions

Three kinds of metal-plastic multilayer composites, which were composed of a steel backing, a middle layer of sintered porous bronze and a surface layer of polytetrafluoroethylene (PTFE) filled by Pb or Cu₂O powders, were prepared. The friction and wear properties as well as the limiting pressure times velocity (PV) values of these metal-plastic multilayer composites sliding against 45 carbon steel under both dry and oil lubricated conditions were evaluated on a MPV-1500 friction tester with a steel axis rotating on a journal bearing. The worn surfaces of these metal-plastic multilayer composites and the transfer films formed on the surface of steel axis were examined by electron probe microscopy analysis (EPMA). Experimental results show that filling of Pb to PTFE reduces the friction coefficient and wear of the composite, while filling of Cu₂O to PTFE increases the friction coefficient but decreases the wear of the composite. The friction and wear properties as well as the limiting PV values of these metal-plastic multilayer composites can be greatly improved with the oil lubrication. EPMA investigations show that Pb and Cu₂O fillers preferentially transfer onto the surfaces of steel axis, which may enhance or deteriorate the adhesion between transfer films and steel surfaces. Meanwhile the transfer of these metal-plastic multilayer composites onto the steel surface can be greatly reduced with oil lubrication, which results in the remarkable decrease of the wear of these metal-plastic multilayer composites.     

Friction and wear characteristics of lead and its compounds filled polytetrafluoroethylene composites under oil lubricated conditions

The friction and wear properties of Pb, PbO, Pb₃O₄, or PbS filled polytetrafluoroethylene (PTFE) composites sliding against GCr15 bearing steel under both dry and liquid paraffin lubricated conditions were studied by using an MHK-500 ring-block wear tester. The worn surfaces and the transfer films of these PTFE composites formed on the surface of GCr15 bearing steel were then investigated by using a scanning electron microscope (SEM) and an optical microscope, respectively. Experimental results show that filling Pb, PbO, Pb₃O₄ or PbS to PTFE can greatly reduce the wear of the PTFE composites, but the wear reducing action of Pb₃O₄ is the most effective. Meanwhile, PbS increases the friction coefficient of the PTFE composite, but Pb and Pb₃O₄ reduce the friction coefficients of the PTFE composites. However, the friction and wear properties of lead or its compounds filled PTFE composites can be greatly improved by lubrication with liquid paraffin, and the friction coefficients of the PTFE composites can be decreased by one order of magnitude. Optical microscope investigation of transfer films shows that Pb, PbO, Pb₃O₄ and PbS enhance the adhesion of the transfer films to the surface of GCr15 bearing steel, so they greatly reduce the wear of the PTFE composites. However, the transfer of the PTFE composites onto the surface of GCr15 bearing steel can be greatly reduced by lubrication with liquid paraffin, but the transfer still takes place. SEM examination of worn surfaces shows that the interaction between liquid paraffin and the PTFE composites creates some cracks on the worn surfaces of the PTFE composites; the creation and development of the cracks reduces the load-carrying capacity of the PTFE composites, and this leads to deterioration of the friction and wear properties of the PTFE composites filled with lead or its compounds under higher loads in liquid paraffin lubrication.     

Friction and wear properties of metal powder filled PTFE composites under oil lubricated conditions

Four kinds of polytetrafluoroethylene (PTFE)-based composite, pure PTFE, PTFE+30vol.%Cu, PTFE+30vol.%Pb and PTFE+30vol.%Ni composite, were prepared. The friction and wear properties of these metal powder filled PTFE composites sliding against GCr15 bearing steel under both dry and lubricated conditions were studied using an MHK-500 ring-block wear tester. The worn surfaces of the PTFE composites and the transfer films formed on the surface of GCr15 bearing steel were examined using scanning electron microscopy (SEM) and optical microscopy respectively. Experimental results show that the friction and wear properties of the PTFE composites can be greatly improved by liquid paraffin lubrication. The wear of these PTFE composites can be decreased by at least 1 to 2 orders of magnitude compared with that under dry friction conditions, while the friction coefficients can be decreased by 1 order of magnitude, SEM and optical microscopy investigations of the rubbing surfaces show that metal fillers of Cu, Pb and Ni not only raise the load carrying capacity of the PTFE composites, but also promote transfer of the PTFE composites onto the counterfaces, so they greatly reduce the wear of the PTFE composites. However, the transfer of these PTFE composites onto the counterfaces can be greatly reduced by liquid paraffin lubrication, but transfer still takes place.     

偶件表面粗糙度对PTFE密封材料摩擦磨损性能的影响

在干摩擦和油润滑条件下,采用MRH-3型高速环块摩擦磨损试验机研究不同粗糙度的45#钢环对PTFE摩擦副摩擦磨损性能的影响,借助白光干涉仪和SEM分析不同试环粗糙度下PTFE磨损后的表面形貌,结合油缸和密封件的工况分析油缸内壁粗糙度对密封材料磨损的原因和机制。结果表明:45#钢环表面粗糙度存在一个最佳的范围,在此范围内摩擦因数均较小;在干摩擦条件下,钢环表面粗糙度过高或过低时,PTFE磨损率均比较大,在油润滑条件下,PTFE磨损率一般随钢环表面粗糙度的增大而升高;粗糙度较大时,PTFE的损伤以犁沟损伤为主。     

干摩擦工况下Si3N4/PTFE配副材料摩擦磨损特性与转移膜形成分析

为使全陶瓷轴承在干摩擦工况下可靠运转,选用四氟乙烯(PTFE)材质的保持架为全陶瓷轴承提供润滑.利用Rtec销/盘摩擦磨损试验机,以PTFE盘与氮化硅(Si3 N4)销为摩擦副,研究Si3 N4/PTFE在不同载荷和转速条件下的摩擦磨损性能,通过SEM对Si3 N4表面的转移膜形貌进行观察,分析转移膜形成原因.结果表明...     

润滑油添加剂对聚合物及其复合材料摩擦磨损性能的影响

利用MHK-500型环-块磨损试验机研究了二烷基二硫代磷酸锌(ZDDP)对几种聚合物及其复合材料-金属摩擦副油润滑摩擦磨损性能的影响。结果表明,液体石蜡中的ZDDP对尼龙66(PA66)及聚酰亚胺(PI)-GCr15轴承钢摩擦副的摩擦系数影响不大,但却使聚四氟乙烯(PTEE)及其复合材料-GCr15轴承钢摩擦副的摩擦系数略有降低。PTEE及其复合材料-GCr15轴承钢摩擦副表面的ZDDP吸附膜具有一定的抗磨作用,它大幅度降低了Pb、PbO及MoS     

Low Wear Steel Counterface Texture Design: A Case Study Using Micro-pits Texture and Alumina–PTFE Nanocomposite

Laser-induced surface micro-pits pattern has been successfully used under fluid lubrication to reduce friction and wear through mechanisms of enhanced hydrodynamic lubrication and fluid retention. Limited successes of friction and wear reduction using solid lubricant and textured surfaces have been reported in the literature, and there still lacks an efficient way of finding textures that produce desired tribological performances. This study evaluates the effect of counterface micro-pits texture on wear of a notable alumina–PTFE nanocomposite and uses the Taguchi method and “Simplex Method” to find the micro-pits parameters producing the lowest wear of the composite material. The optimum texture found yields a composite wear rate of 1 × 10^?7 mm³/Nm, a value identical to the material’s wear rate against untextured counterface. However, when slid against a freshly replaced composite pin, the existing transfer film on the optimum texture reduces composite’s wear volume at low wear transition by 90% and yields a steady-state wear rate of 3.9 × 10^?7 mm³/Nm. On the contrary, preexisting low wear transfer film on untextured counterface increases wear of the newly replaced pin by 10× and yields a wear rate of 4.4 × 10^?6 mm³/Nm. Results in this study suggest larger, shallower and sparser counterface pits are more favorable for debris entrapment, transfer film formation and wear reduction when slid against polymeric solid lubricants. It also raises new possibilities of self-adapting low wear counterface texture design that could potentially support low wear without requiring large amounts of run-in wear volume of bulk solid lubricants.     

Friction and Wear Behavior of Ultra-High Molecular Weight Polyethylene Sliding Against GCr15 Steel and Electroless Ni–P Alloy Coating Under the Lubrication of Seawater

The friction and wear behavior of ultra-high molecular weight polyethylene (UHMWPE) sliding against GCr15 steel and electroless Ni-P alloy coating under the lubrication of seawater was investigated and compared with that under dry sliding and lubrication of pure water and 3.5 wt.% NaCl solution, respectively. It was found that under the lubrication of aqueous medium, the friction and wear behavior of UHMWPE mainly depended on the corrosion of counterface and the lubricating effect of the medium. Because of serious corrosion of counterface by the medium, the wear rates of UHMWPE sliding against GCr15 under the lubrication of seawater and NaCl solution were much larger than that under other conditions, and such a kind of wear closely related to the corrosion of counterface can be reckoned as indirect corrosive wear. However, when sliding against corrosion-resistant Ni–P alloy under the lubrication of seawater, the lowest coefficient of friction and wear rate of UHMWPE were obtained, owing to superior lubricating effect of seawater. Moreover, periodic ripple patterns were observed on the worn surfaces of UHMWPE sliding against GCr15 under the lubrication of seawater and NaCl solution, which were ascribed to the intelligent reconstruction of surface microstructure of UHMWPE upon large plowing effect of the counterface asperities. Based on scanning electron microscopic (SEM) and three-dimensional (3D) profile analyses of the worn surfaces of UHMWPE, a stick–slip dynamic mechanism was proposed to illustrate the pattern abrasion of UHMWPE. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

The tribological properties of PTFE filled with thermally treated nano-attapulgite

The nano-attapulgite powder was treated by heating at 100, 200, 300, 400, 500, 600, 700 and 800 °C for 2 h in a muffle furnace. PTFE composites were prepared by compression molding PTFE and thermally treated nano-attapulgite. The friction and wear tests were performed on a block-on-ring wear tester. Scanning Electron Microscopy (SEM), Energy-Dispersive X-ray Spectrometer (EDS) and Differential Scanning Calorimetry (DSC) were utilized to investigate material microstructures and examine modes of failure. Experimental results showed that under all experimental conditions there was no significant change in coefficient of friction, but the wear rate of PTFE composites was orders of magnitude less than that of pure PTFE under same experimental conditions. Moreover, thermally treated attapulgite was superior to untreated attapulgite in enhancing the wear resistance of PTFE. In addition, the wear resistance increased monotonically with increasing treated attapulgite concentration. Hardness analysis revealed the hardness of PTFE composites increased with increasing content of treated attapulgite. Investigation of transfer film and analysis of debris for PTFE and its composites showed that thermally treated nano-attapulgite filled to PTFE could facilitate formation of transfer film on the steel ring surface and inhibit breakage of PTFE molecular chain. The composites with higher heat absorption capacity exhibited improved wear resistance. Furthermore, the steel ring counterface abrasion was not found.     

多因素影响的格莱圈材料摩擦磨损试验研究*

格莱圈由聚四氟乙烯(PTFE)矩形滑环和丁腈橡胶(NBR)O形圈组成。为了研究不同因素对于格莱圈密封材料摩擦磨损性能的影响,利用UMT-3多功能摩擦磨损试验机,通过改变往复频率、粗糙度、润滑状态研究格莱圈材料与45钢配副时的摩擦磨损性能,利用SEM对试块试验前后表面形貌进行观测,并对摩擦磨损机制进行分析。试验结果表明:在干摩擦和滴油润滑条件下PTFE材料相比NBR材料具有更为优异的摩擦磨损性能;NBR材料表面粗糙度过高或过低都会导致摩擦因数升高,表面粗糙度对具有自润滑性能的PTFE材料的摩擦因数影响不大;高往复频率会使NBR材料摩擦因数降低,过高或过低的往复频率都会使PTFE材料摩擦因数降低;NBR材料的磨损形式以磨粒磨损和黏着磨损为主,PTFE材料以黏着磨损和疲劳磨损为主。     

On the friction and wear behavior of PTFE composite filled with rare earths treated carbon fibers under oil-lubricated condition

Carbon fibers (CF) were surface treated with air-oxidation, air-oxidation followed by rare earths (RE) treatment and RE treatment, respectively. The friction and wear properties of the polytetrafluoroethylene (PTFE) composites filled with differently surface treated carbon fibers, sliding against GCr15 steel under oil lubrication, were investigated on a reciprocating ball-on-disk UMT-2MT tribometer. The worn surfaces of the PTFE composites were examined using a scanning electron microscopy (SEM). Experimental results revealed that surface treatment of carbon fibers reduced the wear of CF-reinforced PTFE composites. Among all the treatments to carbon fibers, RE treatment was the most effective and lowest friction and wear rate of CF-reinforced PTFE composite was exhibited, owing to the effective improvement of the interfacial adhesion between the carbon fibers and PTFE matrix.     

Impact of Viscoelasticity on the Tribological Behavior of PTFE Composites for Valve Seals Application

In this article, we studied and explored the impact of viscoelasticity on the friction and wear behavior of pure polytetrafluoroethylene (PTFE), carbon–graphite PTFE composite, and glass fiber–MoS₂ PTFE composite. Tests were carried out using a specific reciprocating tribometer for valve seal application. The worn surfaces of the PTFE composites and the transfer films formed on the counterface were examined with a scanning electron microscope (SEM). Experimental results revealed that the addition of filler materials was effective in reducing the wear volume in all composites studied. In addition, the friction coefficient and wear resistance showed high sensitivity to the viscoelastic behavior of the PTFE seal. SEM investigation showed that the incorporation of particulate fillers into the PTFE matrix could dramatically reduce and stabilize the transfer films to the counterface, so they largely decreased the wear of the PTFE composites.     

PTFE复合材料的摩擦磨损性能研究

用机械共混、冷压成型烧结的方法制备了纳米SiO2/石墨/玻璃纤维/PTFE复合材料试样。用MM-200型磨损试验机测试了在干摩擦条件下不同载荷时各试样的摩擦磨损性能;用扫描电镜对磨损后试件表面进行观察和分析。研究结果表明：纳米SiO2和玻璃纤维有效提高了PTFE的承载能力,石墨的加入起到了减小摩擦的作用;在本试验条件下,在摩擦过程中三元混合填充PTFE复合材料在偶件表面形成了转移膜,减少了复合材料与偶件的直接接触,因而表现出优异的抗磨性。     

Friction and wear of polyphenylene sulfide composites filled with micro and nano CuO particles in water-lubricated sliding

The tribological behavior of polyphenylene sulfide (PPS) composites filled with micro and nano CuO particles in water-lubricated sliding condition were studied. Pin-on-disk sliding tests were performed against a steel counterface of surface roughness 0.09–0.11 μm. The lubrication regimes were established from friction data corresponding to various combinations of loads and sliding speeds. Later experiments were performed using the sliding speed of 0.5 m/s and contact pressure of 1.95 MPa, which corresponded to boundary lubrication regime. Micro CuO particles as the filler were effective in reducing the wear of PPS but nano CuO particles did not reduce wear. The steady state wear rate of PPS-30 vol.% micro CuO composite was about 10% of that of unfilled PPS and the coefficient of friction in this case was the lowest. The examination of the topography of worn pin surfaces of nano CuO-filled PPS by SEM revealed grooving features indicating three-body abrasion. The transfer films formed on the counterfaces during sliding were studied by optical microscopy and AFM. The wear behavior of the composites in water-lubricated sliding is explained using the characteristics of worn pin surfaces and transfer films on the counterface.     

高能电子辐照对PTFE填充酚酞聚芳醚酮复合材料摩擦磨损性能的影响

用MM-200型摩擦磨损试验机考察了辐照对PTFE填充酚酞聚芳醚酮复合材料的摩擦磨损性能的影响。结果表明：PEK-C复合材料经辐照后其磨擦磨损性能变差。电镜分析表明,辐照样品的磨屑大于未辐照后样品的磨屑。辐照样品的磨损表面梨沟较明显,而未辐照样品的磨损表面无犁沟槽,且表面比较光滑,而电子探针微区分析EPMA表明,辐照样品与钢环对磨后,其摩擦表面较粗糙,钢环表面没有形成连续、均匀的转移膜;而未辐照样品与钢环对磨后,它们的摩擦表面较光滑,钢环表面均形成了较连续、均匀的转移膜。     

纳米ZnO填充的PTFE基复合材料摩擦学性能研究

得胜０００型摩擦磨损试验机研究了不同体积含量的纳米氧化锌（ＺｎＯ）填充的ＰＴＦＥ基复合材料在于摩擦条件下与不风对摩时的摩擦学性能,并利用扫描电子微镜（ＳＥＭ）对ＰＴＦＥ及纳米ＺｎＯ／ＰＴＦＥ复合材料的微观结构、磨损表面和转移膜进行了观察和分析。结果表明,纳米ＺｎＯ／ＰＴＦＥ复合材料的摩擦性能与纯ＰＴＦＥ基本相当,但耐磨性明显优于后者,纳米ＺｎＯ在复合材料中的最佳含量为１５ｖｏｌ．％左右。     

Transfer film bonding and wear studies on CuS-nylon composite sliding against steel

The tribological behaviour of nylon 11 reinforced with lead sulphide filler was studied. The composite specimens with different filler proportions were made by compression moulding. The friction and wear experiments were run under ambient conditions in a pin-on-disk machine with the composite pin riding on the flat surface of a steel disk. It was found that 35 vol.% PbS-nylon composite had the highest wear resistance. The friction and wear tests were run with this composite at different loads, speeds and counterface roughnesses. The wear rate increased considerably when the load was increased from 19.6 N to 39.2 N and the sliding speed from 1 m/s to 2 m/s, but the effect of these increases on the coefficient of friction was very small. The wear rate also increased abruptly when the surface roughness was increased from 0.11 to 0.3 μm but the coefficient of friction was not affected. It was found that the wear process was dominated by the transfer film that formed on the counterface. The transfer film and the worn surfaces were studied by scanning electron microscopy. XPS analysis indicated chemical bonding between the polymer composite transfer film and the steel counterface.     

Tribology of selectively irradiated PTFE surfaces

Selectively irradiated polytetrafluoroethylene (PTFE) surfaces combining the low friction and non-abrasive attributes of an unirradiated polymer with the enhanced wear resistance of wholly irradiated PTFE are demonstrated. Augmented wear resistance, similar to that of filled PTFE composites, is obtained without the accompanying counterface abrasion typical of hard particulate fillers. Friction of these ‘composite’ irradiated/unirradiated surfaces can be less than that of unirradiated PTFE, as irradiated regions limit transfer morphology to only thin oriented films. Spatially distributed irradiated and unirradiated surface regions are patterned by masking 225 keV incident electrons. Under the given contact conditions (6.5 MPa nominal pressure against polished stainless steel) such self-lubricating, wear-resistant composite surfaces had lifetimes of several kilometers sliding distance before giving way to rapid wear of the underlying unmodified PTFE. This revised version was published online in June 2006 with corrections to the Cover Date.     

Surface characterization of polytetrafluoroethylene (PTFE) transfer films during rolling-sliding tribology tests using X-ray photoelectron spectroscopy

A disk-on-disk Amsler wear tester simulating the rolling-sliding motion and high pressure during wheel/rail contact, was used to study the wear performance of PTFE including its film transfer and material flow properties. The chemical composition of the transfer film formed on the wheel-disk surface at various test stages were analyzed by X-ray photoelectron spectroscopy (XPS). The friction curve of the PTFE films obtained on the Amsler can be divided into three regions, according to the friction level and disk surface morphology. Initially, there is a rapid increase of friction coefficient which is presumably accompanied by a fast material transfer from pre-coated rail-disk to the wheel-disk surfaces. In the second region, the friction remains stable throughout and the XPS results show the presence of PTFE on the wheel-disk surface which confirms a transfer of material between the two contact surfaces. In addition, the splitting of F 1s and C 1s photoelectron peaks of PTFE, as a result of a discrepancy in surface charging, suggests that the transfer film exists in two forms: thick patch and thin film. With an increase in rolling cycles, the thick patches become thinner, as well as its coverage reduces. By contrast, the thin film gains both in thickness and coverage. Using a simple model, the thin film is calculated to be only a few nanometers thick. At the beginning of the third region, only a thin film is left on the surface. Additional rolling leads to a rapid rise in friction and the transfer film thickness continues to decrease. The evidence supports the removal of PTFE out of the contact zone, and a high friction coefficient (μ = 0.6) is reached at the end of the test indicating an un-lubricated metal-metal contact. No major tribochemical reaction of PTFE is observed during this study.     

Self-Lubricating PTFE-Based Composites with Black Phosphorus Nanosheets

Black phosphorus (BP), a newly emerging two-dimensional material, has recently received considerable attention. Our recent work suggested that BP nanosheets exhibit extraordinary mechanical and lubrication properties. In the present work, the tribological properties of polyetheretherketone (PEEK)/polytetrafluoroethylene (PTFE) and carbon fiber (CF)/PTFE composites with BP nanosheets have been investigated. The morphologies and surface element distribution of the worn tracks of the tribopair surfaces were examined by different analytical techniques. The results show that the coefficients of friction (COFs) of both the PEEK/PTFE and CF/PTFE composites decreased dramatically after the addition of BP nanosheets, and the minimum COF of the composite was 0.04, which was a quarter of that of the PTFE composite without BP nanosheets. After BP nanosheets were added into the composites, the wear rate of the PTFE/PEEK composite decreased dramatically, while that of the CF/PTFE composite increased significantly with the increase in the filler concentration. The analysis of the lubrication mechanism of the PTFE composite with BP nanosheets suggested that BP nanosheets could be constantly supplied into the contact area and gradually formed a BP film composed of phosphorus oxide and phosphoric acid on the counterpart surface instead of the formation of PTFE transfer film. The formed BP transfer film promoted the friction reduction and the disappearance of the adhesive wear.