Effect of different curd-washing methods on the insoluble Ca content and rheological properties of Colby cheese during ripening

A curd-washing step is used in the manufacture of Colby cheese to decrease the residual lactose content and, thereby, decrease the potential formation of excessive levels of lactic acid. The objective of this study was to investigate the effect of different washing methods on the Ca equilibrium and rheological properties of Colby cheese. Four different methods of curd-washing were performed. One method was batch washing (BW), where cold water (10°C) was added to the vat, with and without stirring, where curds were in contact with cold water for 5 min. The other method used was continuous washing (CW), with or without stirring, where curds were rinsed with continuously running cold water for approximately 7 min and water was allowed to drain immediately. Both methods used a similar volume of water. The manufacturing pH values were similar in all 4 treatments. The insoluble (INSOL) Ca content of cheese was measured by juice and acid-base titration methods and the rheological properties were measured by small amplitude oscillatory rheology. The levels of lactose in cheese at 1 d were significantly higher in CW cheese (0.06-0.11%) than in BW cheeses (∼0.02%). The levels of lactic acid at 2 and 12 wk were significantly higher in CW cheese than in BW cheeses. No differences in the total Ca content of cheeses were found. Cheese pH increased during ripening from approximately 5.1 to approximately 5.4. A decrease in INSOL Ca content of all cheeses during ripening occurred, although a steady increase in pH took place. The initial INSOL Ca content as a percent of total Ca in cheese ranged from 75 to 78% in all cheeses. The INSOL Ca content of cheese was significantly affected by washing method. Stirring during manufacturing did not have a significant effect on the INSOL Ca content of cheese during ripening. Batch-washed cheeses had significantly higher INSOL Ca contents than did CW cheeses during the first 4 wk of ripening. The maximum loss tangent values (meltability index) of CW cheese at 1 d and 1 wk were significantly higher compared with those of BW cheeses. In conclusion, different curd washing methods have a significant effect on the levels of lactose, lactic acid, meltability, and INSOL Ca content of Colby cheese during ripening.     

Impact of modifications in acid development on the insoluble calcium content and rheological properties of Cheddar cheese

Cheddar cheese was made from milk concentrated by reverse osmosis (RO) to increase the lactose content or from whole milk. Manufacturing parameters (pH at coagulant addition, whey drainage, and milling) were altered to produce cheeses with different total Ca contents and low pH values (i.e., <5.0) during ripening. The concentration of insoluble (INSOL) Ca in cheese was measured by cheese juice method, buffering by acid-base titration, rheological properties by small amplitude oscillatory rheometry, and melting properties by UW-Melt Profiler. The INSOL Ca content as a percentage of total Ca in all cheeses rapidly decreased during the first week of aging but surprisingly did not decrease below approximately 41% even in cheeses with a very low pH (e.g., ∼4.7). Insoluble Ca content in cheese was positively correlated (r = 0.79) with cheese pH in both RO and nonRO treatments, reflecting the key role of pH and acid development in altering the extent of solubilization of INSOL Ca. The INSOL Ca content in cheese was positively correlated with the maximum loss tangent value from the rheology test and the degree of flow from the UW-Melt Profiler. When cheeses with pH <5.0 where heated in the rheometer the loss tangent values remained low (<0.5), which coincided with limited meltability of Cheddar cheeses. We believe that this lack of meltability was due to the dominant effects of reduced electrostatic repulsion between casein particles at low pH values (<5.0).     

Effect of camel chymosin on the texture,functionality, and sensory properties of low-moisture,part-skim Mozzarella cheese

The objective of this study was to compare the effect of coagulant (bovine calf chymosin, BCC, or camel chymosin, CC), on the functional and sensory properties and performance shelf-life of low-moisture, part-skim (LMPS) Mozzarella. Both chymosins were used at 2 levels [0.05 and 0.037 international milk clotting units (IMCU)/mL], and clotting temperature was varied to achieve similar gelation times for each treatment (as this also affects cheese properties). Functionality was assessed at various cheese ages using dynamic low-amplitude oscillatory rheology and performance of baked cheese on pizza. Cheese composition was not significantly different between treatments. The level of total calcium or insoluble (INSOL) calcium did not differ significantly among the cheeses initially or during ripening. Proteolysis in cheese made with BCC was higher than in cheeses made with CC. At 84 d of ripening, maximum loss tangent values were not significantly different in the cheeses, suggesting that these cheeses had similar melt characteristics. After 14 d of cheese ripening, the crossover temperature (loss tangent = 1 or melting temperature) was higher when CC was used as coagulant. This was due to lower proteolysis in the CC cheeses compared with those made with BCC because the pH and INSOL calcium levels were similar in all cheeses. Cheeses made with CC maintained higher hardness values over 84 d of ripening compared with BCC and maintained higher sensory firmness values and adhesiveness of mass scores during ripening. When melted on pizzas, cheese made with CC had lower blister quantity and the cheeses were firmer and chewier. Because the 2 types of cheeses had similar moisture contents, pH values, and INSOL Ca levels, differences in proteolysis were responsible for the firmer and chewier texture of CC cheeses. When cheese performance on baked pizza was analyzed, properties such as blister quantity, strand thickness, hardness, and chewiness were maintained for a longer ripening time than cheeses made with BCC, indicating that use of CC could help to extend the performance shelf-life of LMPS Mozzarella.     

Effect of lactose standardization of milk using low-concentration factor ultrafiltration: Effect of reducing the lactose-to-casein ratio on the properties of milled-curd Cheddar cheese

The pH of cheese is determined by the amount of lactose fermented and the buffering capacity of the cheese. The buffering capacity of cheese is largely determined by the protein contents of milk and cheese and the amount of insoluble calcium phosphate in the curd, which is related to the rate of acidification. The objective of this study was to standardize both the lactose and casein contents of milk to better control final pH and prevent the development of excessive acidity in Cheddar cheese. This approach involved the use of low-concentration factor ultrafiltration of milk to increase the casein content (～5%), followed by the addition of water, ultrafiltration permeate, or both to the retentate to adjust the lactose content. We evaluated milks with 4 different lactose-to-casein ratios (L:CN): 1.8 (control milk), 1.4, 1.1, and 0.9. All cheesemilks had similar total casein (2.3%) and fat (3.4%) contents. These milks were used to make milled-curd Cheddar cheese, and we evaluated cheese composition, texture, functionality, and sensory properties over 9 mo of ripening. Cheeses made from milks with varying levels of L:CN had similar moisture, protein, fat, and salt contents, due to slight modifications during manufacture (i.e., cutting the gel at a smaller size than control) as well as control of acid development at critical steps (i.e., cutting the gel, whey drainage, salting). As expected, decreasing the L:CN led to cheeses with lower lactic acid, residual lactose, and insoluble Ca contents, as well as a substantial pH increase during cheese ripening in cheeses. The L:CN ratio had no significant effect on the levels of primary and secondary proteolysis. Texture profile analysis showed no significant differences in hardness values during ripening. Maximum loss tangent, an index of cheese meltability, was lower until 45 d for the L:CN 1.4 and 0.9 treatments, but after 45 d, all reduced L:CN cheeses had higher maximum loss tangent values than the control cheese (L:CN 1.8). Sensory analyses showed that cheeses made from milks with reduced L:CN contents had lower acidity, sourness, sulfury notes, and chewdown cohesiveness. Standardization of milk to a specific L:CN ratio, while maintaining a constant casein level in the milk, would allow Cheddar cheese manufacturers to have tighter control of pH and acidity.     

Influence of calcium and phosphorus, lactose, and salt-to-moisture ratio on Cheddar cheese quality: manufacture and composition

Eight Cheddar cheeses with 2 levels of calcium (Ca) and phosphorus (P), residual lactose, and salt-to-moisture ratio (S/M) were manufactured. All cheeses were made using a stirred-curd procedure and were replicated 3 times. Treatments with a high level of Ca and P were produced by setting the milk and drawing the whey at a higher pH (6.6 and 6.3, respectively) compared with the treatments with a low level of Ca and P (pH of 6.2 and 5.7, respectively). The lactose content in the cheeses was varied by adding lactose (2.5% by weight of milk) to the milk for high lactose cheeses, and washing the curd for low lactose cheeses. The difference in S/M was obtained by dividing the curds into halves, weighing each half, and salting at 3.5 and 2.25% of the weight of the curd for high and low S/M, respectively. All cheeses were salted at a pH of 5.4. Modifications in cheese-making protocols produced cheeses with desired differences in Ca and P, residual lactose, and S/M. Average Ca and P in the high Ca and P cheeses was 0.68 and 0.48%, respectively, vs. 0.53 and 0.41% for the low Ca and P cheeses. Average lactose content of the high lactose treatments at d 1 was 1.48% compared with 0.30% for the low lactose treatments. The S/M for the high and low S/M cheeses was 6.68 and 4.77%, respectively. Mean moisture, fat, and protein content of the cheeses ranged from 32.07 to 37.57%, 33.32 to 35.93%, and 24.46 to 26.40%, respectively. The moisture content differed among the treatments, whereas fat and protein content on dry basis was similar.     

Changes in the proportions of soluble and insoluble calcium during the ripening of cheddar cheese

In cheese, the concentration and form of residual Ca greatly influences texture. Two methods were used to determine the proportions of soluble (SOL) and insoluble (INSOL) Ca in Cheddar cheese during 4 mo of ripening. The first method was based on the acid-base buffering curves of cheese and the second was based on the extraction of the aqueous phase ("juice") of cheese under high pressure and determining the concentration of SOL Ca in the juice using atomic absorption spectroscopy. When cheese was acidified there was a strong buffering peak at pH approximately 4.8, which was due to the solubilization of residual colloidal calcium phosphate (CCP) of milk that remained in cheese as INSOL Ca phosphate. The area of this buffering peak in cheese was expressed as a percentage of the original area of this peak in milk and was used to estimate the concentration of residual INSOL Ca phosphate in cheese. There were no significant differences between the 2 methods. The proportions of INSOL Ca in cheese decreased from approximately 73 to approximately 58% between d 1 and 4 mo. These methods will be useful techniques to study the role of Ca in cheese texture and functionality.     

Influence of calcium and phosphorus, lactose, and salt-to-moisture ratio on cheddar cheese quality: pH changes during ripening

The pH of cheese is an important attribute that influences its quality. Substantial changes in cheese pH are often observed during ripening. A combined effect of calcium, phosphorus, residual lactose, and salt-to-moisture ratio (S/M) of the cheese on the changes in cheese pH during ripening was investigated. Eight cheeses with 2 levels of Ca and P (0.67 and 0.47% vs. 0.53 and 0.39%, respectively), lactose at pressing (2.4 vs. 0.78%), and S/M (6.4 vs. 4.8%) were manufactured. All the cheeses were salted at a pH of 5.4, pressed for 5 h, and then ripened at 6 to 8°C. The pH of the salted curds before pressing and the cheeses during 48 wk of ripening was measured. Also, cheeses were analyzed for water-soluble Ca and P, organic P, and bound inorganic P during ripening. Changes in organic acids’ concentration and shifts in the distribution of Ca and P between different forms were studied in relation to changes in pH. Cheeses with low S/M exhibited a larger increase in acid production during ripening compared with high S/M cheeses. Cheeses with the highest concentration of bound inorganic P exhibited the highest pH, whereas cheeses with the lowest concentration of bound inorganic P exhibited the lowest pH among the 8 treatments. Although conversion of lactose to short-chain, water-soluble organic acids decreased cheese pH, bound inorganic phosphate buffered the changes in cheese pH. Production of acid in excess of the buffering capacity (which was the case in low Ca and P and low S/M treatments) led to a low pH, whereas solubilization of bound inorganic P in excess to acid production (which was the case in high Ca and P and high S/M treatments) led to an increase in pH. However, for cheeses with high Ca and P and low S/M, changes in cheese pH were influenced by the level of residual lactose. Hence, pH changes in Cheddar cheese can be modulated by a concomitant control on the amount and state of Ca and P, level of residual lactose, and S/M of the cheese.     

Glycolysis and related reactions during cheese manufacture and ripening

Fermentation of lactose to lactic acid by lactic acid bacteria is an essential primary reaction in the manufacture of all cheese varieties. The reduced pH of cheese curd, which reaches 4.5 to 5.2, depending on the variety, affects at least the following characteristics of curd and cheese: syneresis (and hence cheese composition), retention of calcium (which affects cheese texture), retention and activity of coagulant (which influences the extent and type of proteolysis during ripening), the growth of contaminating bacteria. Most (98%) of the lactose in milk is removed in the whey during cheesemaking, either as lactose or lactic acid. The residual lactose in cheese curd is metabolized during the early stages of ripening. During ripening lactic acid is also altered, mainly through the action of nonstarter bacteria. The principal changes are (1) conversion of L-lactate to D-lactate such that a racemic mixture exists in most cheeses at the end of ripening; (2) in Swiss-type cheeses, L-lactate is metabolized to propionate, acetate, and CO2, which are responsible for eye formation and contribute to typical flavor; (3) in surface mold, and probably in surface bacterially ripened cheese, lactate is metabolized to CO2 and H2O, which contributes to the increase in pH characteristic of such cheeses and that is responsible for textural changes, (4) in Cheddar and Dutch-type cheeses, some lactate may be oxidized to acetate by Pediococci. Cheese contains a low level of citrate, metabolism of which by Streptococcus diacetylactis leads to the production of diacetyl, which contributes to the flavor and is responsible for the limited eye formation characteristic of such cheeses.     

Evaluation of biogenic amines and microbial counts throughout the ripening of goat cheeses from pasteurized and raw milk

The effect of the hygienic quality of milk on changes in microbial counts and biogenic amine content was evaluated during ripening of goat cheeses manufactured from pasteurized and raw milks at 1, 14, 30, 60 and 90 d. The original milk, rennet, curd and whey were also included in the study. The pH, salt content and extent of proteolysis in the cheese were also evaluated. Spermidine and spermine were the main amines in raw milk, while they were minor amines in cheeses. Other amines increased markedly during ripening, tyramine being the main amine in cheese made from raw milk and cadaverine and putrescine in those produced from pasteurized milk. Enterobacteriaceae counts decreased during ripening whereas those of lactic acid bacteria increased, especially lactobacilli and enterococci. Cheese made from raw milk showed higher microbial counts during ripening than those made from pasteurized milk, especially for Enterobacteriaceae and enterococci, counts being 2 or 3 log units higher. Raw milk cheese showed remarkably higher biogenic amines compared with pasteurized milk cheeses. Therefore, pasteurization of milk causes a decrease in final biogenic amine content of cheese as a result of the reduction of its microbial counts.     

Effects of the concentration of insoluble calcium phosphate associated with casein micelles on the functionality of directly acidified cheese

Directly acidified cheeses with different insoluble Ca (INS Ca) contents were made to test the hypothesis that the removal of INS Ca from casein micelles (CM) would directly contribute to the softening and flow behavior of cheese at high temperature. Skim milk was directly acidified with dilute lactic acid to pH values of 6.0, 5.8, 5.6, or 5.4 to remove INS Ca (pH trial). Lowering milk pH also reduced protein charge repulsion, which could influence melt. In a second treatment, EDTA (0, 2, 4, or 6 mM) was added to skim milk that was subsequently acidified to pH 6.0 (EDTA trial). Both types of milks were then made into directly acidified cheese. Cheese properties were determined at approximately 10 h after pressing to reduce possible confounding effects of proteolysis. The INS Ca content was determined by the acid-base titration method. Dynamic low-amplitude oscillatory rheology was used to measure the viscoelastic properties of cheese during heating from 5 to 80°C. The composition of all cheeses was as similar as possible, with cheese-making procedures being modified to obtain similar moisture contents (∼55%). Insoluble Ca contents of cheeses significantly decreased with a reduction in pH or with the addition of EDTA to skim milk. The pH values of cheeses in the pH trial varied, but all cheeses in the EDTA trial had similar pH values (∼5.73). In the pH trial, the reduction in cheese pH and consequent decrease in INS Ca content resulted in a reduction in the G′ values of cheeses at 20°C. In contrast, the G′ values at 20°C in cheeses from the EDTA trial increased with EDTA addition up to 4 mM EDTA. The G′ values at 70°C of cheeses from the pH trial decreased with a decrease in cheese pH, and a similar decrease was observed in the G′ values of cheese from the EDTA trial with an increase in EDTA concentration even though these cheeses had a similar pH value. In both trials, loss tangent (LT) values increased with temperatures >30°C and reached a maximum at approximately 70°C. In the pH trial, LT values at 70°C increased from 1.50 to 4.24 with a decrease in cheese pH from 5.78 to 5.21. The LT values increased from 1.43 to 3.23 with an increase in the concentration of added EDTA from 0 to 6 mM. In the EDTA trial, the decrease in G′ and increase in LT values at 70°C were due to the reduction in INS Ca content, because the pH values of these cheeses were the same. It can be concluded that the loss of INS Ca increases the melting in cheeses that have the same pH and gross chemical composition, and removal of INS Ca can even make cheese at high pH (∼5.73) exhibit reasonable melt characteristics.     

Chymosin-mediated proteolysis, calcium solubilization, and texture development during the ripening of cheddar cheese

Full fat, milled-curd Cheddar cheeses (2 kg) were manufactured with 0.0 (control), 0.1, 1.0, or 10.0 μmol of pepstatin (a potent competitive inhibitor of chymosin) added per liter of curds/whey mixture at the start of cooking to obtain residual chymosin levels that were 100, 89, 55, and 16% of the activity in the control cheese, respectively. The cheeses were ripened at 8°C for 180 d. There were no significant differences in the pH values of the cheeses; however, the moisture content of the cheeses decreased with increasing level of pepstatin addition. The levels of pH 4.6-soluble nitrogen in the 3 cheeses with added pepstatin were significantly lower than that of the control cheese at 1 d and throughout ripening. Densitometric analysis of urea-PAGE electro-phoretograms of the pH 4.6-insoluble fractions of the cheese made with 10.0 μmol/L of pepstatin showed complete inhibition of hydrolysis of α_S1-casein (CN) at Phe₂₃-Phe₂₄ at all stages of ripening. The level of insoluble calcium in each of 4 cheeses decreased significantly during the first 21 d of ripening, irrespective of the level of pepstatin addition. Concurrently, there was a significant reduction in hardness in each of the 4 cheeses during the first 21 d of ripening. The softening of texture was more highly correlated with the level of insoluble calcium than with the level of intact α_S1-CN in each of the 4 cheeses early in ripening. It is concluded that hydrolysis of α_S1-CN at Phe₂₃-Phe₂₄ is not a prerequisite for softening of Cheddar cheese during the early stages of ripening. We propose that this softening of texture is principally due to the partial solubilization of colloidal calcium phosphate associated with the para-CN matrix of the curd.     

Improving the quality of Ras-type cheese made from recombined milk containing high levels of total solids

Ras type cheese was made from recombined milk (RM) containing normal (12·5%) or high levels of Total Solids (TS) (25%, 32% or 40%) using fresh or recombined cream. Cheese curds obtained from RM containing high TS levels were moulded directly or after washing with warm water (50°C) for 10 min before moulding. The cheeses were matured at 7°C or 15°C. Cheese made from fresh milk was better in flavour and consistency than any of the cheeses made from RM. Use of RM in which fresh cream was used gave cheeses of better quality than those made from RM containing recombined cream. Washing the curd made from all RMs resulted in cheeses with better flavour and body characteristics than those made from unwashed curd. Cheese made from RM containing 25% TS with or without washing of the curds was of better quality than those made from RM containing 32% or 40% TS.The changes of nitrogenous fractions, degradation of α_sI- and β-caseins, accumulation of free amino acids and the formation of free fatty acids were reduced as the level of TS in RM was increased. All cheeses made from washed RM curd showed greater proteolysis and lipolysis compared with those made from unwashed curd. Storage of RM cheese at 15°C accelerated its ripening and improved cheese quality compared with ripening at 7°C.     

Slower proteolysis in Cheddar cheese made from high-protein cheese milk is due to an elevated whey protein content

A growing number of companies within the cheese-making industry are now using high-protein (e.g., 4–5%) milks to increase cheese yield. Previous studies have suggested that cheeses made from high-protein (both casein and whey protein; WP) milks may ripen more slowly; one suggested explanation is inhibition of residual rennet activity due to elevated WP levels. We explored the use of microfiltration (MF) to concentrate milk for cheese-making, as that would allow us to concentrate the casein while varying the WP content. Our objective was to determine if reducing the level of WP in concentrated cheese milk had any impact on cheese characteristics, including ripening, texture, and nutritional profile. Three types of 5% casein standardized and pasteurized cheese milks were prepared that had various casein:true protein (CN:TP) ratios: (a) control with CN:TP 83:100, (b) 35% WP reduced, 89:100 CN:TP, and (c) 70% WP reduced, 95:100 CN:TP. Standardized milks were preacidified to pH 6.2 with dilute lactic acid during cheese-making. Composition, proteolysis, textural, rheological, and sensory properties of cheeses were monitored over a 9-mo ripening period. The lactose, total solids, total protein, and WP contents in the 5% casein concentrated milks were reduced with increasing levels of WP removal. All milks had similar casein and total calcium levels. Cheeses had similar compositions, but, as expected, lower WP levels were observed in the cheeses where WP depletion by MF was performed on the cheese milks. Cheese yield and nitrogen recoveries were highest in cheese made with the 95:100 CN:TP milk. These enhanced recoveries were due to the higher fraction of nitrogen being casein-based solids. Microfiltration depletion of WP did not affect pH, sensory attributes, or insoluble calcium content of cheese. Proteolysis (the amount of pH 4.6 soluble nitrogen) was lower in control cheeses compared with WP-reduced cheeses. During ripening, the hardness values and the temperature of the crossover point, an indicator of the melting point of the cheese, were higher in the control cheese. It was thus likely that the higher residual WP content in the control cheese inhibited proteolysis during ripening, and the lower breakdown rate resulted in its higher hardness and melting point. There were no major differences in the concentrations of key nutrients with this WP depletion method. Cheese milk concentration by MF provides the benefit of more typical ripening rates.     

Survival of Listeria monocytogenes during the manufacture and ripening of Turkish white cheese

Listeria monocytogenes was enumerated during the manufacture and ripening of Turkish White cheese with particular reference to a) pasteurized milk, b) cheese milk after inoculation with L. monocytogenes (0 h), c) after curd formation (2 h), d) curd after pressing (6 h), e) curd after pH was reduced (17 h), f) curd after salting (32 h), and g) cheeses during ripening. Cheeses were also examined periodically for total solids, moisture and salt contents, pH values and aerobic plate count. An increase in the number of L. monocytogenes was observed during manufacture. Following salting and throughout the storage period, numbers of L. monocytogenes decreased at a rate depending on the salt concentration, starter activity and storage time. The initial microbial number had a significant (P < 0.01) effect on the survival of L. monocytogenes during the storage period.     

Use of cold microfiltration retentates produced with polymeric membranes for standardization of milks for manufacture of pizza cheese

Pizza cheese was manufactured with milk (12.1% total solids, 3.1% casein, 3.1% fat) standardized with microfiltered (MF) and diafiltered retentates. Polymeric, spiral-wound MF membranes were used to process cold (<7°C) skim milk, and diafiltration of MF retentates resulted in at least 36% removal of serum protein on a true protein basis. Cheese milks were obtained by blending the MF retentate (16.4% total solids, 11.0% casein, 0.4% fat) with whole milk (12.1% total solids, 2.4% casein, 3.4% fat). Control cheese was made with part-skim milk (10.9% total solids, 2.4% casein, 2.4% fat). Initial trials with MF standardized milk resulted in cheese with approximately 2 to 3% lower moisture (45%) than control cheese (∼47 to 48%). Cheese-making procedures (cutting conditions) were then altered to obtain a similar moisture content in all cheeses by using a lower setting temperature, increasing the curd size, and lowering the wash water temperature during manufacture of the MF cheeses. Two types of MF standardized cheeses were produced, one with preacidification of milk to pH 6.4 (pH6.4MF) and another made from milk preacidified to pH 6.3 (pH6.3MF). Cheese functionality was assessed by dynamic low-amplitude oscillatory rheology, University of Wisconsin MeltProfiler, and performance on pizza. Nitrogen recoveries were significantly higher in MF standardized cheeses. Fat recoveries were higher in the pH6.3MF cheese than the control or pH6.4MF cheese. Moisture-adjusted cheese yield was significantly higher in the 2 MF-fortified cheeses compared with the control cheese. Maximum loss tangent (LT_max) values were not significantly different among the 3 cheeses, suggesting that these cheeses had similar meltability. The LT_max values increased during ripening. The temperature at which the LT_max was observed was highest in control cheese and was lower in the pH6.3MF cheese than in the pH6.4MF cheese. The temperature of the LT_max decreased with age for all 3 cheeses. Values of 12% trichloroacetic acid soluble nitrogen levels were similar in all cheeses. Performance on pizza was similar for all cheeses. The use of MF retentates derived with polymeric membranes was successful in increasing cheese yield, and cheese quality was similar in the control and MF standardized cheeses.     

Influence of cheese-making recipes on the composition and characteristics of Camembert-type cheese

Bloomy rind cheeses, including Camembert and related varieties, can be produced using alternative processes that vary based on milk preacidification, cutting, curd handling, and ripening parameters. Modification of these parameters creates distinct cheeses such as lactic curd, stabilized curd, and hybrids of the two. The objective of this study was to determine the influence of 5 Camembert-type cheese recipes on the composition and characteristics during ripening. Five varieties of Camembert-type cheese were produced: (1) lactic curd, (2) sweet curd, (3) washed curd, (4) solubilized curd, and (5) stabilized curd. Cheeses were aged at 13°C for 10 d, during the mold growth phase, and 7°C from d 11 until 50. Key quality metrics including texture development, pH (center and surface), and color were monitored throughout shelf-life. Compositional evaluation (d 5; fat, protein, moisture, salt, and minerals) grouped cheeses into 3 categories: (1) lactic curd, (2) sweet and washed curd, and (3) solubilized and stabilized curd. The lactic curd and stabilized curd were consistently the most different varieties for composition and quality metrics. Moisture content of Camembert-type varieties ranged from 53.15 to 57.99%, Ca ranged from 0.23 to 0.45%, and P ranged from 0.21 to 0.40%. All varieties followed the expected pH evolution on the rind and in the paste with the pH of the rind reaching 7 by d 10, and paste pH reaching 7 between 35 and 50 d. The displacement of the paste (distance traveled upon cutting) for the lactic curd was the greatest among the 5 varieties, reaching an average of 27 ± 1.9 mm (mean ± standard error) after 50 d of ripening and 60 min of flow time. The stabilized curd on the other hand traveled the shortest distance, reaching an average of 4 ± 0.4 mm at the same time point. Browning, considered a defect in mold-ripened cheeses, was observed in all varieties, but was most substantial for lactic curd (lightness, L*, decreased from 87.19 to 68.58). Based on these quality metrics the shelf-life of these recipes was estimated with the lactic curd having the shortest, and the stabilized curd having the longest. Examining Camembert-type cheese quality metrics for these 5 varieties can assist cheesemakers during recipe formulation and selection of cheese-making practices to achieve optimum product quality.     

Effect of Curd Washing Level on Proteolysis and Functionality of Low-Moisture Mozzarella Cheese Made with Galactose-Fermenting Culture

Abstract: The effect of curd washing on functional properties of low-moisture mozzarella cheese made with galactose-fermenting culture was investigated. A total of 4 curd washing levels (0%, 10%, 25%, 50% wt/wt) were used during low-moisture mozzarella cheese manufacture, and cheeses were stored for 63 d at 4 °C and the influence of curd washing on proteolysis and functionality of low-moisture mozzarella cheese were examined. Curd washing had a significant effect on moisture and ash contents. In general, moisture contents increased and ash contents decreased with increased curd washing levels. Low-moisture mozzarella cheese made with 10% curd washing levels showed higher proteolysis, meltability, and stretchability during storage than other experimental cheeses. In general, galactose contents decreased during storage; however, cheeses made with 25% and 50% curd washing levels had lower galactose contents than those with control or 10%. L*-values (browning) decreased and proteolysis increased in low-moisture mozzarella cheeses during storage.     

Survial of Listeria monocytogenes during the manufacture and ripening of Turkish White cheese

Listeria monocytogenes was enumerated during the manufacture and ripening of Turkish White cheese with particular reference to a) pasteurized milk, b) cheese milk after inoculation with L. monocytogenes (0 h( c) after curd formation (2 h( d) curd after pressing (6 h( e) curd after pH was reduced (17 h( f) curd after salting (32 h( and g) cheeses during ripening. Cheeses were also examined periodically for total solids, moisture and salt contents, pH values and aerobic plate count. An increase in the number ofL. monocytogenes was observed during manufacture. Following salting and throughout the storage period, numbers of L. monocytogenes decreased at a rate depending on the salt concentration, starter activity and storage time. The initial microbial number had a significant (P > 0.01) effect on the survival of L. monocytogenes during the storage period.