Alumina Sol-Assisted Sintering of SiC—Al2O3 Composites

The composite sol—gel (CSG) technology has been utilized to process SiC—Al₂O₃ ceramic/ceramic particulate reinforced composites with a high content of SiC (up to 50 vol%). Alumina sol, resulting from hydrolysis of aluminum isopropoxide, has been utilized as a dispersant and sintering additive. Microstructures of the composites (investigated using TEM) show the sol-originating phase present at grain boundaries, in particular at triple junctions, irrespective of the type of grain (i.e., SiC or Al₂O₃). It is hypothesized that the alumina film originating from the alumina sol reacts with SiO₂ film on the surface of SiC grains to form mullite or alumina-rich mullite-glass mixed phase. Effectively, SiC particles interconnect through this phase, facilitating formation of a dense body even at very high SiC content. Comparative sinterability studies were performed on similar SiC—Al₂O₃ compositions free of alumina sol. It appears that in these systems the large fraction of directly contacting SiC—SiC grains prevents full densification of the composite. The microhardness of SiC—Al₂O₃ sol—gel composites has been measured as a function of the content of SiC and sintering temperature. The highest microhardness of 22.9 GPa has been obtained for the composition 50 vol% SiC—50 vol% Al₂O₃, sintered at 1850°C.     

Preparation of Titanium Nitride/Alumina Laminate Composites

A preparation route for TiN/Al₂O₃ laminate composites has been described. A water-based process using Al₂O₃ and TiN slurries with solids contents of 40 and 35 vol%, respectively, was used to make TiN and Al₂O₃ tapes. The removal of the binder was monitored by weight-loss measurements in a thermogravimetry unit. Bodies composed of Al₂O₃ and TiN tapes were densified at temperatures of 1400° and 1500°C using the Spark Plasma Sintering^® (SPS) technique. Densities of >98% of the theoretical densities were approached. Crack-free and almost fully densified TiN/Al₂O₃ compacts were prepared by heating the burned-out green bodies to the final sintering temperature (1500°C) at a rate of 100°C/min, and with a holding time of 5–10 min, under a pressure of 75 MPa. The microstructures of the obtained compacts were studied using scanning electron microscopy. Grain sizes in the sintered Al₂O₃ and TiN compacts were similar to those of the precursor powders. Hardness and indentation fracture toughness were measured at room temperature, and the monolithic compacts as well as the laminate composites exhibited anisotropic mechanical behavior; i.e., the cracks propagated much more easily in a direction parallel to the laminas than perpendicular to them.     

Synthesis of BaCu(B2O5) Ceramics and their Effect on the Sintering Temperature and Microwave Dielectric Properties of Ba(Zn1/3Nb2/3)O3 Ceramics

BaCu(B₂O₅) ceramics were synthesized and their microwave dielectric properties were investigated. BaCu(B₂O₅) phase was formed at 700°C and melted above 850°C. The BaCu(B₂O₅) ceramic sintered at 810°C had a dielectric constant (ɛ_r) of 7.4, a quality factor ( Q × f ) of 50 000 GHz and a temperature coefficient of resonance frequency (τ_f) of −32 ppm/°C. As the BaCu(B₂O₅) ceramic had a low melting temperature and good microwave dielectric properties, it can be used as a low-temperature sintering aid for microwave dielectric materials for low temperature co-fired ceramic application. When BaCu(B₂O₅) was added to the Ba(Zn_1/3Nb_2/3)O₃ (BZN) ceramic, BZN ceramics were well sintered even at 850°C. BaCu(B₂O₅) existed as a liquid phase during the sintering and assisted the densification of the BZN ceramic. Good microwave dielectric properties of Q × f =16 000 GHz, ɛ_r=35, and τ_f=22.1 ppm/°C were obtained for the BZN+6.0 mol% BaCu(B₂O₅) ceramic sintered at 875°C for 2 h.     

Phase Transformation of Diphasic Aluminosilicate Gels

Aluminosilicate gels with compositions Al₂O₂/SiO₂ and 2 were prepared by gelling a mixture of colloidal pseudo-boehmite and a silica sol prepared from acid-hydrolyzed Si(OC₂H₅)₄. Upon heating the pseudo-boehmite transforms to γ-Al₂O₃ around 400°C, then to δ-Al₂O₃ at 1050°C, and at 1200°C reacts with amorphous SiO₂ to form mullite. Some twinned θ-Al₂O₃ forms before mullite. Nonstoichiometric specimens have a similar transformation sequence, but form mullite grains with inclusions of either Al₂O₃ or cristobalite, often associated with dislocation networks or micropores. Mullite grains are formed by nucleation and growth and have equiaxed shape.     

Sol–Gel Processed Y-PSZ Ceramics with 5 wt% Al2O3

Y-PSZ ceramics with 5 wt% Al₂O₃ were synthesized by a sol–gel route. Experimental results show that powders of metastable tetragonal zirconia with 2.7 mol% Y₂O₃ and 5 wt% Al₂O₃ can be fabricated by decomposing the dry gel powder at 500°C. Materials sintered in an air atmosphere at 1500°C for 3 have high density (5.685 g/cm³), high content of metastable tetragonal zirconia (>96%), and high fracture toughness (8.67 MPa.m^1/2). Compared with the Y-PSZ ceramics, significant toughening was achieved by adding 5 wt% Al₂O₃.     

Chemical Vapor Deposition of Polycrystalline Al2O3

Polycrystalline Al₂O₃ was chemically vapor-deposited onto sintered Al₂O₃ substrates by reaction of AlCl₃ with (1) H₂O, (2) CO:H₂, and (3) O₂ at 1000° and 1500°C and 0.5 and 5.0 torr. Although the thermodynamics of all these reactions predict the formation of solid Al₂O₃, the deposition rate of the first reaction was considerably greater than that of the second. The third reaction was so slow that no measurable deposit was formed in 6 h at 1500°C. Formation of dense deposits of α-Al₂O₃ was favored by increasing temperature and decreasing pressure. Microstructural examination of the dense deposits showed long columnar grains, the largest of which extended through the deposit from the substrate to the surface.     

Synthesis, Densification, and Phase Evolution Studies of Al2O3–Al2TiO5–TiO2 Nanocomposites and Measurement of Their Electrical Properties

Alumina–aluminum titanate–titania (Al₂O₃–Al₂TiO₅–TiO₂) nanocomposites were synthesized using alkoxide precursor solutions. Thermal analysis provided information on phase evolution from the as-synthesized gel with an increase in temperature. Calcination at 700°C led to the formation of an Al₂O₃–TiO₂ nanocomposite, while at a higher temperature (1300°C) an Al₂O₃–Al₂TiO₅–TiO₂ nanocomposite was formed. The nanocomposites were uniaxially compacted and sintered in a pressureless environment in air to study the densification behavior, grain growth, and phase evolution. The effects of nanosize particles on the crystal structure and densification of the nanocomposite have been discussed. The sintered nanocomposite structures were also characterized for dielectric properties.     

Growth of Tabular α-Al2O3 Grains on Porous Alumina Substrate

Gradient, porous alumina ceramics were prepared with the characteristics of microsized tabular α-Al₂O₃ grains grown on a surface with a fine interlocking feature. The samples were formed by spin-coating diphasic aluminosilicate sol on porous alumina substrates. The sol consisted of nano-sized pseudo-boehmite (AlOOH) and hydrolyzed tetraethyl orthosilicate [Si(OC₂H₅)₄]. After drying and sintering at 1150°–1450°C, the crystallographic and chemical properties of the porous structures were investigated by analytical electron microscopy. The results show that the formation of tabular α-Al₂O₃ grains is controlled by the dissolution of fine Al₂O₃ in the diphasic material at the interface. The nucleation and growth of tabular α-Al₂O₃ grains proceeds heterogeneously at the Al₂O₃/glass interface by ripening nano-sized Al₂O₃ particles.     

Influence of the Characteristics of Spinels on the Slag Resistance of Al2O3–MgO and Al2O3–Spinel Castables

The XRD patterns at ambient temperature and at 1500°C showed that the spinel in the Al₂O₃–MgO castables fired at 1500°C for 3 h has the higher peak intensity, compared to those in Al₂O₃–spinel castables; the interplanar distance in the set (311) is 2.43 Å for the spinel in Al₂O₃–MgO castables as well as the spinels in Al₂O₃–spinel castables using spinels containing 73, 90, and 94 wt% Al₂O₃, respectively. The corresponding alumina contents of the spinels in these castables were estimated to be around 75 wt%. The smaller grain size of the spinel in Al₂O₃–MgO castables compared to that in Al₂O₃–spinel castables is evidenced by the recrystallization of the in situ spinel only occurring in Al₂O₃–MgO castables as revealed by the XRD patterns at ambient temperature and at 1500°C. The larger amount and smaller grain size of the in situ spinel in the matrix mostly account for the better slag resistance of Al₂O₃–MgO castables, compared to Al₂O₃–spinel castables.     

Homogeneous ZrO2–Al2O3 Composite Prepared by Nano-ZrO2 Particle Multilayer-Coated Al2O3 Particles

ZrO₂–Al₂O₃ nanocomposite particles were synthesized by coating nano-ZrO₂ particles on the surface of Al₂O₃ particles via the layer-by-layer (LBL) method. Polyacrylic acid (PAA) adsorption successfully modified the Al₂O₃ surface charge. Multilayer coating was successfully implemented, which was characterized by ξ potential, particle size. X-ray diffraction patterns showed that the content of ZrO₂ in the final powders could be well controlled by the LBL method. The powders coated with three layers of nano-ZrO₂ particles, which contained about 12 wt% ZrO₂, were compacted by dry press and cold isostatically pressed methods. After sintering the compact at 1450°C for 2 h under atmosphere, a sintered body with a low pore microstructure was obtained. Scanning electron microscopy micrographs of the sintered body indicated that ZrO₂ was well dispersed in the Al₂O₃ matrix.     

Microstructure and Bending Strength of 3Y-TZP/12Ce-TZP Ceramics Fabricated by Liquid-Phase Sintering at Low Temperature

With the addition of 1 wt% of MgO–Al₂O₃–SiO₂ glass as a sintering aid, 3Y-TZP/12Ce-TZP ceramics (composed from a mixture of 3Y-TZP and 12Ce-TZP powder) have been fabricated via liquid-phase sintering at 1250°–1400°C. In the sintered bodies, the grain growth of Y-TZP is almost unaffected, whereas that of Ce-TZP is inhibited. MgO·Al₂O₃ spinel and an amorphous phase that contains Al₂O₃ and SiO₂ (from the sintering aid) fully fill the grain junctions. The bending strength of 3Y-TZP/12Ce-TZP, when sintered at 1250°–1300°C, is ∼800–900 MPa, which is greater than that of 3Y-TZP ceramics without Ce-TZP particles. Ce-TZP grains and MgO·Al₂O₃ spinel in 3Y-TZP/12Ce-TZP ceramics may impede crack growth, and the bending strength is enhanced.     

Reaction Processing of Al2O3 Composites Containing Iron and Iron Aluminides

Different Fe-Al₂O₃ and FeAl-Al₂O₃ composites with metallic contents up to 30 vol% have been fabricated via reaction processing of Al₂O₃, Fe, and Al mixtures. Low Al contents (<∼10 vol%) within the starting mixture lead to composites consisting of Fe embedded in an Al₂O₃ matrix, whereas aluminide-containing Al₂O₃ composites result from powder mixtures with higher Al contents. In both cases, densification up to 98% TD can be achieved by pressureless sintering in inert atmosphere at moderate temperatures (1450°-1500°C). The proposed reaction sintering mechanism includes the reduction of native oxide layers on the surface of the Fe particles by Al and, in the case of mixtures with high Al contents, aluminide formation followed by sintering of the composites. Density and bending strengths of the reaction-sintered composites depend strongly on the Al content of the starting mixture. In the case of samples containing elemental Fe, crack path observations indicate the potential for an increase of fracture toughness, even at room temperature, by crack bridging of the ductile Fe inclusions.     

Electroconductive Al2O3–NbN Composites

Electroconductive Al₂O₃–NbN ceramic composites were prepared by hot pressing. Dense sintered bodies of ball-milled Al₂O₃–NbN composite powders were obtained at 1550°C and 30 MPa for 1 h under a nitrogen atmosphere. The bending strength and fracture toughness of the composites were enhanced by incorporating niobium nitride (NbN) particles into the Al₂O₃ matrix. The electrical resistivity of the composites decreased with increasing amount of NbN phase. For a 25 vol% NbN–Al₂O₃ composite, the values of bending strength, fracture toughness, Vickers hardness, and electrical resistivity were 444.2 MPa, 4.59 MPa·m^1/2, 16.62 GPa, and 1.72 × 10⁻²Ω·cm, respectively, making the composite suitable for electrical discharge machining.     

Effect of Aqueous Processing Conditions on the Microstructure and Transformation Behavior in Al2O3─ZrO2(CeO2) Composites

Aqueous processing of Al₂O₃─ZrO₂ (123 mol% CeO₂) composites, combined with sintering conditions, was used to control the microstructure and its influence on the martensitic transformation temperature of t -ZrO₂ and the transformation-toughening contribution at room temperature. The resultant ZrO₂ grain sizes in the dense composites were related to the transformation-toughening behavior of t -ZrO₂. The data show that (1) the best processing conditions exist when the electrophoretic mobilities of the two solids are positive, adequately high to ensure colloidal stability, efficient packing,and uniform ZrO₂ distribution but differ greatly in magnitude, (2) the colloidal stability of ZrO₂ controls the overall stability and the rheological and processing behavior of this mixture, (3) the grain size distribution in dense pieces sintered for 1 h at 1500°C is comparable to the particle size distribution of the powders, (4) the martensite start temperature for the tetragonal to-monoclinic transformation in Al₂O₃ containing 20 and 40 vol% ZrO₂ increases and can approach 0°C with increasing average ZrO₂ grain size, and as a result, (5) the fracture toughness values at room temperature are raised from 4–5 MPa.m^1/2 to 9–12 MPa.m^1/2 for these two compositions.     

Thermal Conductivity of Sintered UO, and Al2O3 at High Temperatures

The thermal conductivities of sintered Al₂O₃ and UO₂ were measured in the ranges 400° to 1700°C and 300° to 2100°C respectively. The conductivity values for Al₂O₃ agreed with those reported previously at all temperatures investigated. The conductivity of UO, decreased with increasing temperature to a minimum of 0.0050 cal per cm sec °C at about 1400°C, and then increased with increasing temperature to 0.0105 cal per cm sec °C at 2100°C.     

Transformation Plasticity and Toughening in CeO2-Partially-Stabilized Zirconia–Alumina (Ce-TZP/Al2O3) Composites Doped with MnO

Microstructure, phase stability, and mechanical properties of CeO₂-partially-stabilized zirconia (12 mol% Ce-TZP) containing 10 wt% Al₂O₃ and 1.5 wt% MnO were studied in relation to the base Ce-TZP and the Ce-TZP/Al₂O₃ composite without MnO. The MnO reacted with both CeO₂ and Al₂O₃ to form a new phase of approximate composition CeMnAl₁₁O₁₉. The reacted phase had a magnetoplumbite structure and formed elongated, needlelike crystals. The MnO-doped Ce-TZP/Al₂O₃ composites sintered at an optimum temperature of 1550°C exhibited high strength (650 MPa in four-point bending) and rising crack-growth-resistance behavior, with fracture toughness increasing from 7.6 to 10.3 MPa.In¹² in compact tension tests. These improved mechanical properties were associated with relatively high tetragonal-to-monoclinic transformation temperature ( M _s=−42°C) at small grain size (2.5 μm), significant transformation plasticity in mechanical tests (bending, uniaxial tension, and uniaxial compression) and transformation zones at crack tips in compact tension specimens. The transformation yield stress, zone size, and fracture toughness were sensitive to the sintering temperature varied in the range 1500° to 1600°C. Analysis of the transformation zones using Raman microprobe spectroscopy and calculation of zone shielding for the observed zones indicated that a large fraction of the fracture toughness (∼70%) was derived from transformation toughening.     

Mechanical Properties and Fracture Toughness of α-Al2O3-Platelet-Reinforced Y-PSZ Composites at Room and High Temperatures

YPSZ/Al₂O₃-platelet composites were fabricated by conventional and tape-casting techniques followed by sintering and HIPing. The room-temperature fracture toughness increased, from 4.9 MPa·m^1/2 for YPSZ, to 7.9 MPa·m^1/2 (by the ISB method) for 25 mol% Al₂O₃ platelets with aspect ratio = 12. The room-temperature fiexural strength decreased 21% and 30% (from 935 MPa for YPSZ) for platelet contents of 25 vol% and 40 vol%, respectively. Al₂O₃ platelets improved the high-temperature strength (by 110% over YPSZ with 25 vol% platelets at 800°C and by 40% with 40 vol% platelets at 1300°C) and fracture toughness (by 90% at 800°C and 61% at 1300°C with 40 vol% platelets). An amorphous phase at the Al₂O₃-platelet/YPSZ interface limited mechanical property improvement at 1300°C. The influence of platelet alignment was examined by tape casting and laminating the composites. Platelet alignment improved the sintered density by >1% d _th , high-temperature strength by 11% at 800°C and 16% at 1300°C, and fracture toughness by 33% at 1300°C, over random platelet orientation.     

Microstructure and Mechanical Properties of Mullite Prepared by the Sol-Gel Method

Mullite (3Al₂O₃·2SiO₂) of stoichiometric composition was prepared by mixing boehmite sol and silica dispersion and gelling at a pH of 3. Complete mullitization takes place at or above 1300°C. Ultrafine mullite powder prepared by calcining gel at 1400°C and attrition milling could be sintered to >98% (theoretical density) at 1650°C for 1.5 h. The flexural strength of the sintered body at room temperature was 405 MPa and 350 MPa at 1300°C. Only traces of a secondary phase were observed along the grain boundary.     

Synthesis and Properties of CaAl2O4-Coated AI2O3 Microcomposite Powders

Novel microcomposite powders, consisting of inert cores (αAL-Al₂O₃) surrounded by reactive cement-based coatings (CaAl₂O₄), were synthesized by a modified Pechini process. The evolution of the crystalline CaAl₂O₄ phase during calcination was studied using multiple analytical techniques, including DRIFTS,¹³C and ²⁷AlMAS FT-NMR, and XRD, for both pure CaAl₂O₄ and CaAl₂O₄-coated Al₂O₃ precursor powders. In both powders, decomposition proceeded via hydrocarbon chain scission and removal of ester groups at low temperatures ( T < 450°C), followed by the formation of inorganic carbonates at higher temperatures ( T > 450°C). These decomposition processes were accelerated by the underlying Al₂O₃ cores. Transmission electron microscopy (TEM) of the fully calcined powders showed that the inert αAL-Al₂O₃ particles were surrounded by relatively uniform CaAl₂O₄ coatings ranging in thickness from approximately 10 to 100 nm.     

Synthesis and Microwave Dielectric Properties of Re3Ga5O12 (Re: Nd, Sm, Eu, Dy, Yb, and Y) Ceramics

Re₃Ga₅O₁₂ (Re: Nd, Sm, Eu, Dy, Yb, and Y) garnet ceramics were synthesized and their microwave dielectric properties were investigated for advanced substrate materials in microwave integrated circuits. The Re₃Ga₅O₁₂ ceramics sintered at 1350°–1500°C had a high-quality factor ( Q × f ) ranging from 40 000 to 192 173 GHz and a low-dielectric constant (ɛ_r) of between 11.5 and 12.5. They also exhibited a relatively stable temperature coefficient of resonant frequency (τ_f) in the range of −33.7 to −12.4 ppm/°C. In particular, the Sm₃Ga₅O₁₂ ceramics sintered at 1450°C exhibited good microwave dielectric properties of ɛ_r=12.4, Q × f =192 173 GHz, and τ_f=−19.2 ppm/°C.