An advanced bipolar-MOS-I2L technology with a thin epitaxial layer for analog-digital VLSI

A novel Bi-MOS technology, Advanced Bipolar CMOS (ABC), is proposed. Bipolar transistors (n-p-n, p-n-p, I²L) and MOS transistors (both n- and p-channel) have been successfully fabricated on the same chip with no decrease in performance by using a 3-µm design rule. Thin epitaxial layer (leq 2 microm) is used in order to obtain small-size high-performance (3-GHz) bipolar devices. Device size is reduced by using a shallow junction and self-aligning technique. n-channel MOS transistors are formed in p-well regions designed to reach p-type substrate, and p-channel MOS transistors are formed in epitaxial layer with an n⁺buried layer. This technology has the potential for monolithic multifunctional analog-digital VLSI.     

Process and Device Performance of Submicrometer-Channel CMOS Devices Using Deep-Trench Isolation and Self-Aligned TiSi/sub 2/ Technologies

According to our scaling study, a deeper n-well allows for a lower n-well surface concentration with improved short-channel effects in submicrometer-channel PMOS-FET's. The deep n-well, however, requires a large space between n- and p-channel devices. This large space limits the integration density in scaled bulk CMOS VLSI's. The deep-trench isolation combined with an epitaxial layer resolves this drawback with significantly improved device-to-device isolation and latchup susceptibility. The 6-/spl mu/m-deep with 2-/spl mu/m-wide deep trench is etched in the epitaxial layer and is refilled with 1500 /spl Aring/ of thermal silicon-dioxide film and 2/spl mu/m of polysilicon film. The sheet resistances of N/sup +/ and P/sup +/ diffusion and N/sup +/ -doped polysilicon layers were reduced to 3 to 4 /spl Omega//spl square/ by using the self-aligned TiSi/sub 2/ layer with an oxide sidewall spacer. As a result of this low sheet resistance, the saturation drain current of submicrometer n- and p-channel MOSFET's was improved approximately 33 to 37 percent compared with conventional MOSFET's without the self-aligned TiSi/sub 2/ layer. The 0.5-/spl mu/m-channel CMOS devices using the deep-trench isolation with an epitaxial layer and the self-aligned TiSi/sub 2/ layer operated at a propagation delay time of 140 ps with a power dissipation of 1.1 mW per inverter and attained a maximum clock frequency of 400 MHz in a static /spl divide/ 4 counter without suffering from Iatchup even at the Iatchup trigger current of 200 mA.     

Optimized retrograde N-well for 1-/spl mu/m CMOS technology

Using experiment and simulation, transistors in a high-energy implanted N-well are designed for optimum device performance suitable for 1-/spl mu/m CMOS technology. The effect of process parameters on device performance is obtained. Superior body effect, junction capacitance, punchthrough voltage, and subthreshold slope are achieved for 1-/spl mu/m n- and p-channel transistors. With shallow P/P+ epitaxial material, this retrograde N-well approach also provides latch-up immunity for high-density CMOS.     

A Self-Aliglned 1-/spl mu/m-Channel CMOS Technology with Retrograde n-Well and Thin Epitaxy

A six-mask 1-/spl mu/m CMOS process with many self-aligned features is described. It uses a thin p-type epitaxial layer on a p/sup +/ substrate and a retrograde n-well. Self-aligned TiSi/sub 2/ is formed on n/sup +/ and p/sup +/ diffusions to reduce the sheet resistance and to make butted source contacts. It is shown that n/sup +/ poly-gated p-channel devices can be properly designed with low threshold magnitudes and good turn-off characteristics. With a 5-V supply, the minimum gate delay of unloaded CMOS ring oscillators is 150 ps/stage. Furthermore, it is dernonstrated that this CMOS technology is Iatchup free since the holding voltage for Iatchup is higher than 5 V.     

The impact of device type and sizing on phase noise mechanisms

Phase noise mechanisms in integrated LC voltage-controlled oscillators (VCOs) using MOS transistors are investigated. The degradation in phase noise due to low-frequency bias noise is shown to be a function of AM-PM conversion in the MOS switching transistors. By exploiting this dependence, bias noise contributions to phase noise are minimized through MOS device sizing rather than through filtering. NMOS and PMOS VCO designs are compared in terms of thermal noise. Short-channel MOS considerations explain why 0.18-/spl mu/m PMOS devices can attain better phase noise than 0.18-/spl mu/m NMOS devices in the 1/f/sup 2/ region. Phase noise in the 1/f/sup 3/ region is primarily dependent upon the upconversion of flicker noise from the MOS switching transistors rather than from the bias circuit, and can be improved by decreasing MOS switching device size. Measured results on an experimental set of VCOs confirm the dependencies predicted by analysis. A 5.3-GHz all-PMOS VCO topology demonstrates measured phase noise of -124 dBc/Hz at 1-MHz offset and -100dBc/Hz at 100-kHz offset while dissipating 13.5 mW from a 1.8-V supply using a 0.18-/spl mu/m SiGe BiCMOS process.     

A novel germanium doping method for fabrication of high-performance p-channel poly-Si/sub 1-x/Ge/sub x/ TFT by excimer laser crystallization

In this letter, a novel process for fabricating p-channel poly-Si/sub 1-x/Ge/sub x/ thin-film transistors (TFTs) with high-hole mobility was demonstrated. Germanium (Ge) atoms were incorporated into poly-Si by excimer laser irradiation of a-Si/sub 1-x/Ge/sub x//poly-Si double layer. For small size TFTs, especially when channel width/length (W/L) was less than 2 /spl mu/m/2 /spl mu/m, the hole mobility of poly-Si/sub 1-x/Ge/sub x/ TFTs was superior to that of poly-Si TFTs. It was inferred that the degree of mobility enhancement by Ge incorporation was beyond that of mobility degradation by defect trap generation when TFT size was shrunk to 2 /spl mu/m/2 /spl mu/m. The poly-Si/sub 0.91/Ge/sub 0.09/ TFT exhibited a high-hole mobility of 112 cm/sup 2//V-s, while the hole mobility of the poly-Si counterpart was 73 cm/sup 2//V-s.     

A 2.0-/spl mu/m pixel pitch MOS image sensor with 1.5 transistor/pixel and an amorphous Si color filter

In this paper, an ultrafine pixel size (2.0/spl times/2.0 /spl mu/m/sup 2/) MOS image sensor with very high sensitivity is developed. The key technologies that realize the MOS image sensor are a newly developed pixel circuit configuration (1.5 transistor/pixel), a fine 0.15-/spl mu/m design rule, and an amorphous Si color filter (Si-CF). In the new pixel circuit configuration, a unit pixel consists of one photodiode, one transfer transistor, and an amplifier circuit with two transistors that are shared by four neighboring pixels. Thus, the unit pixel has only 1.5 transistors. The fine design rule of 0.15 /spl mu/m enables reduction of wiring area by 40%. As a result, a high aperture ratio of 30% is achieved. A newly developed Si-CF realizes the 1/10 thickness of that of the conventional organic-pigment CF, giving rise to high light-collection efficiency. With these three technologies combined, a high sensitivity of 3400 electrons/lx/spl middot/s is achieved even with a pixel size of 2.0/spl times/2.0 /spl mu/m/sup 2/.     

A new metal-ferroelectric (PbZr/sub 0.53/Ti/sub 0.47/O/sub 3/)-insulator (Dy/sub 2/O/sub 3/)-semiconductor (MFIS) FET for nonvolatile memory applications

Metal-ferroelectric-insulator-semiconductor (MFIS) field-effect transistors with Pb(Zr/sub 0.53/,Ti/sub 0.47/)O/sub 3/ ferroelectric layer and dysprosium oxide Dy/sub 2/O/sub 3/ insulator layer were fabricated. The out-diffusion of atoms between Dy/sub 2/O/sub 3/ and silicon was examined by secondary ion mass spectrometry profiles. The size of the memory windows was investigated. The memory windows measured from capacitance-voltage curves of MFIS capacitors and I/sub DS/-V/sub GS/ curves of MFIS transistors are consistent. The nonvolatile operation of MFIS transistors was demonstrated by applying positive/negative writing pulses. A high driving current of 9 /spl mu/A//spl mu/m was obtained even for long-channel devices with a channel length of 20 /spl mu/m. The electron mobility is 181 cm/sup 2//V/spl middot/s. The retention properties of MFIS transistors were also measured.     

Interdigitated Ge p-i-n photodetectors fabricated on a Si substrate using graded SiGe buffer layers

We report an interdigitated p-i-n photodetector fabricated on a 1-/spl mu/m-thick Ge epitaxial layer grown on a Si substrate using a 10-/spl mu/m-thick graded SiGe buffer layer. A growth rate of 45 /spl Aring//s/spl sim/60 /spl Aring//s was achieved using low-energy plasma enhanced chemical vapor deposition. The Ge epitaxial layer had a threading dislocation density of 10/sup 5/ cm/sup -2/ and a rms surface roughness of 3.28 nm. The 3-dB bandwidth and the external quantum efficiency were measured on a photodetector having 1-/spl mu/m finger width and 2-/spl mu/m spacing with a 25/spl times/28 /spl mu/m/sup 2/ active area. At a wavelength of 1.3 /spl mu/m, the bandwidth was 2.2, 3.5, and 3.8 GHz at bias voltages of -1, -3, and -5 V, respectively. The dark current was 3.2 and 5.0 /spl mu/A at -3 and -5 V, respectively. This photodetector exhibited an external quantum efficiency of 49% at a wavelength of 1.3 /spl mu/m.     

8.5 m/spl Omega/ /spl middot/ cm/sub 2/ 600-V double-epitaxial MOSFETs in 4H-SiC

The most important issue in realizing a 4H-SiC vertical MOSFET is to improve the poor channel mobility at the MOS interface, which is related to high on-resistance. This letter focuses on a novel 4H-SiC vertical MOSFET device structure where a low acceptor concentration epitaxial layer is used as a channel. We call this structure a double-epitaxial MOSFET (DEMOSFET). In the structure, the p-well is composed of two p-type epitaxial layers, while an n-type region between the p-wells is formed by low-dose n-type ion implantation. A buried channel is formed at the surface of the upper p/sup $/epitaxial layer. A fabricated DEMOSFET showed an on-resistance of 8.5 m/spl Omega//spl middot/cm/sup 2/ at a gate voltage of 15 V and a blocking voltage of 600 V. This on-resistance is the lowest so far reported for a vertical MOSFET with a blocking voltage of 600 V.     

Electrical characteristics of 8-/spl Aring/ EOT HfO/sub 2//TaN low thermal-budget n-channel FETs with solid-phase epitaxially regrown junctions

The authors demonstrate high-performing n-channel transistors with a HfO/sub 2//TaN gate stack and a low thermal-budget process using solid-phase epitaxial regrowth of the source and drain junctions. The thinnest devices have an equivalent oxide thickness (EOT) of 8 /spl Aring/, a leakage current of 1.5 A/cm/sup 2/ at V/sub G/=1 V, a peak mobility of 190 cm/sup 2//V/spl middot/s, and a drive-current of 815 /spl mu/A//spl mu/m at an off-state current of 0.1 /spl mu/A//spl mu/m for V/sub DD/=1.2 V. Identical gate stacks processed with a 1000-/spl deg/C spike anneal have a higher peak mobility at 275 cm/sup 2//V/spl middot/s, but a 5-/spl Aring/ higher EOT and a reduced drive current at 610 /spl mu/A//spl mu/m. The observed performance improvement for the low thermal-budget devices is shown to be mostly related to the lower EOT. The time-to-breakdown measurements indicate a maximum operating voltage of 1.6 V (1.2 V at 125 /spl deg/C) for a ten-year lifetime, whereas positive-bias temperature-instability measurements indicate a sufficient lifetime for operating voltages below 0.75 V.     

Fabrication of Si MOSFET's Using Neutron-Irradiated Silicon as Semi-Insulating Substrate

The feasibility of a novel silicon-on-semi-insulating substrate structure has been demonstrated. MOS field-effect transistors (MOSFET's) are fabricated on neutron-irradiated silicon wafers which are used as semi-insulating substrates. In order to keep the substrate semi-insulating, laser annealing is used to make the semiconducting layer, and to activate the impurities implanted in the semiconducting layer, and plasma anodization is employed to grow the gate oxide. The, mobility of carrier in the channel is about 100 cm/sup 2//V /spl dot/s for p-channel MOSFET's and 300 cm/sup 2//V /spl dot/s for n-channel devices. This structure has inherent advantages such as crystallographicafly single crystalline.     

A VLSI memory management chip: design considerations and experience

The design of a VLSI memory measurement chip which provides the WE 32001 microprocessor with an extensive set of memory management capabilities is described. The chip is implemented in 1.75 /spl mu/m twin-tub CMOS II technology and contains 92000 transistors. Highlights of the technology are the use of twin tubs for independently optimized n- and p-channel transistors, local oxidation and self-aligned channel-stops for parasitic field protection, and the use of an n/SUP +/ substrate for latchup protection. In addition, a composite layer of TaSi over n/SUP +/ polysilicon is used to achieve a fivefold reduction in sheet resistance over the conventional n/SUP +/ polysilicon. Electrical channel lengths for n-channel and p-channel transistors are nominally 1.5 /spl mu/m.     

A 0.7-V MOSFET-only switched-opamp /spl Sigma//spl Delta/ modulator in standard digital CMOS technology

A 0.7-V MOSFET-only /spl Sigma//spl Delta/ modulator for voice band applications is presented. The second-order modulator is realized using a switched-opamp technique. All capacitors are realized using compensated MOS devices operated in the depletion region. A combination of parallel and series compensated depletion-mode MOSCAPs is used to obtain high area efficiency. The circuit is fabricated in a 0.18-/spl mu/m CMOS process. The only components used are standard n-MOS and p-MOS transistors with threshold voltages of approximately 400 mV. All transistors are operated within the supply voltage window of 0.7 V; voltage boosting techniques are not used. The active area is 0.082 mm/sup 2/. The modulator achieves 67-dB signal-to-noise-and-distortion ratio, 70-dB signal-to-noise ratio, and 75-dB dynamic range at 8-kHz signal bandwidth and consumes 80 /spl mu/W of power.     

Low phase noise IP VCO for multistandard communication using a 0.35-/spl mu/m BiCMOS SiGe technology

In this letter, we report that a commonly used 0.35-/spl mu/m, 60-GHz-F/sub MAX/ BiCMOS SiGe monolithic microwave integrated circuit (MMIC) technology is able to provide very low phase noise signal generation in the X-band frequency range. This statement has been demonstrated using a differential LC voltage-controlled oscillator (VCO) in which varactors are realized with metal-oxide semiconductor (MOS) transistors and inductors with a patterned ground shield technology. This VCO features an output power signal in the range of -5 dBm and exhibits a phase noise of -96 dBc/Hz at a frequency offset of 100kHz from carrier and -120 dBc/Hz at a frequency offset of 1 MHz. The VCO features a tuning range of 430 MHz or 4.3% of its operating frequency. Its power consumption is in the range of 70 mW (200 mW with buffers circuits) for a chip size of 800/spl times/1000 /spl mu/m/sup 2/ (including RF probe pads).     

Vertical scaling of 0.25-/spl mu/m emitter InP/InGaAs single heterojunction bipolar transistors with f/sub T/ of 452 GHz

Vertical scaling of the epitaxial structure has allowed submicron InP/InGaAs-based single heterojunction bipolar transistors (SHBTs) to achieve record high-frequency performance. The 0.25/spl times/16 /spl mu/m/sup 2/ transistors, featuring a 25-nm base and a 100-nm collector, display current gain cut-off frequencies f/sub T/ of 452 GHz. The devices operate at current densities above 1000 kA/cm/sup 2/ and have BV/sub CEO/ breakdowns of 2.1 V. A detailed analysis of device radio frequency (RF) parameters, and delay components with respect to scaling of the collector thickness is presented.     

1.0-/spl mu/m n-Well CMOS/Bipolar Technology

High-performance 1.0-/spl mu/m n-well CMOS/bipolar on-chip technology was developed. For process simplicity, an n-well and a collector of bipolar transistors were formed simultaneously, and base and NMOS channel regions were also made simultaneously resulting in collector-isolated vertical n-p-n bipolar transistor fabrication without any additional process step to CMOS process. On the other hand, 1.0-/spl mu/m CMOS with a new "hot carrier resistant" seIf-defined Polysilicon sidewall spacer (SEPOS) LDD NMOS was developed. It can operate safely under supply voltage over 5 V without performance degradation of CMOS circuits. By evaluating ring oscillators and differential amplifiers constructed by both CMOS and bipolar transistors. it can be concluded that in a digital and in an analog combined system, CMOS has sufficiently high-speed performance for digital parts, while bipolar is superior for analog parts. In addition, bipolar transistors with an n/sup +/-buried layer were also fabricated to reduce collector resistance. Concerning the bipolar input/output buffers, the patterned n/sup +/-buried layer improves the drivability and high-frequency response. As a result, the applications of n-well CMOS/bipolar technology become clear. This technology was successfully applied to a high-speed 64-kbit CMOS static RAM, and improvement in access time was observed.     

Large grain poly-Si(/spl sim/rm 10/spl mu/m) TFTs prepared by excimer laser annealing through a thick SiON absorption layer

Poly-Si with large grain size of 10.4/spl times/4.4 /spl mu/m/sup 2/ was realized by excimer laser annealing (ELA) through the substrate and an 1 /spl mu/m thick silicon oxynitride (SiON) absorption layer underlying the top amorphous silicon. Thin-film transistors (TFTs) can then be made on this single poly-Si grain and show good electrical performance.     

Submicron InP-InGaAs single heterojunction bipolar transistors with f/sub T/ of 377 GHz

Submicron InP-InGaAs-based single heterojunction bipolar transistors (SHBTs) are fabricated to achieve record-breaking speed performance using an aggressively scaled epitaxial structure coupled with a submicron emitter process. SHBTs with dimensions of 0.35 /spl times/16 /spl mu/m have demonstrated a maximum current gain cutoff frequency f/sub T/ of 377 GHz with a simultaneous maximum power gain cutoff frequency f/sub MAX/ of 230 GHz at the current density Jc of 650 kA/cm/sup 2/. Typical BV/sub CEO/ values exceed 3.7 V.     

A compact tunable CMOS transconductor with high linearity

A novel CMOS linear transconductor is presented. The use of simple and accurate voltage buffers to drive two MOS transistors operating in the triode region leads to a highly linear voltage-to-current conversion. Transconductance gain can be continuously and precisely adjusted using dc level shifters. Measurement results of a balanced transconductor fabricated in a 0.5-/spl mu/m CMOS technology show a total harmonic distortion of -54 dB at 100 kHz for an 80-/spl mu/A peak-to-peak output, using a supply voltage of 2 V. It requires 0.07-mm/sup 2/ of silicon (Si) area and features 0.96 mW of static power consumption.