Mechanical and dynamic mechanical properties of nylon 66/montmorillonite nanocomposites fabricated by melt compounding

Nylon 66 nanocomposites were prepared by melt compounding of nylon 66 with organically modified montmorillonite (MMT). The organic MMT was pre‐modified with about 14 wt% of ammonium surfactant, much lower than the 35–46 wt% in most commercial organic MMT powders. Transmission electron microscope observation indicated that the MMT layers were well exfoliated in nylon 66 matrix. Dynamic mechanical analysis confirmed the constraint effect of exfoliated MMT layers on nylon 66 chains, which benefited the increased storage modulus, increased glass transition temperature and reduced magnitude of alpha relaxation peak. The effects of organic MMT loading levels on reinforcement and fracture behaviour of the nanocomposites were evaluated using tensile and three‐point bending tests. The addition of the organic MMT clearly increased Young's modulus and tensile strength but decreased ductility and fracture toughness of nylon 66. Copyright © 2004 Society of Chemical Industry     

Preparation and properties of montmorillonite‐based polyimide nanocomposites

Montmorillonite (MMT)‐based polyimide (PI) nanocomposites were prepared via two‐stage polymerization of PI using polyamic acid (PAA). The clay was organically modified using various alkylammonium ions to examine the effect of changes in alkyl length on the intercalation spacing of both the treated clays and their hybrids with PAA and PI. The intercalation behavior of clay in the PI matrix and its thermal and mechanical properties were investigated as a function of clay concentration. The d‐spacing of organically modified MMT (O‐MMT) increased with increasing length of the alkylammonium chain. PI/O‐MMT hybrids form exfoliated nanocomposites at clay concentrations below 2 wt%, while they form intercalated nanocomposites together with some exfoliated ones at clay contents exceeding 4 wt%. Young's modulus increased rapidly to a clay loading of 2 wt%, and leveled off with further increases in clay loading. The tensile strength at break increased rapidly up to a clay loading of 1 wt%, and then decreased sharply, while the strain at break showed a monotonic decrease with increasing clay loading from 0 to 8 wt%. The storage modulus, E′, in the temperature range below the glass transition temperature T_g, generally increased with increasing clay content, except at the highest clay content of 8 wt%. Copyright © 2004 Society of Chemical Industry     

Experimental investigation on the influence of the composition on the morphology and the mechanical properties of short glass fiber‐reinforced polypropylene nanocomposites

Polypropylene composites containing 0–5 wt% layered silicate and 0–30 wt% short glass fibers are prepared by melt compounding. To investigate the influence of different compositions on the mechanical properties of short glass fiber‐reinforced polypropylene nanocomposites, materials with various filler contents are prepared. At a glass fiber content of 10 wt% Young's modulus of the layered silicate‐containing composites decreases by around 30% compared to conventional glass fiber‐reinforced polypropylene. But at higher glass fiber loadings, an increasing modulus of up to 10% is observed. However, the addition of layered silicate results in large decreases of the tensile and the notched impact strength. A maleic anhydride‐grafted polypropylene enhances Young's modulus and the tensile strength. © 2012 Society of Plastics Engineers     

Effect of ethylene‐1‐butene copolymer on tensile properties and toughness of polypropylene/mica/organoclay hybrid nanocomposites

In this study, polypropylene (PP) was reinforced using 1 wt% organically modified‐grafted mica (OMGM) and various levels of Cloisite15A (C15A), 0–3 wt%. For OMGM preparation, polypropylene graft maleic anhydride (PP‐g‐MAH) was grafted onto diacetone acryl amid modified mica. The results showed the highest impact strength enhancement of 68% and Young's modulus of 12% for hybrid nanocomposite containing 1 wt% OMGM and 0.5 wt% C15A when compared to neat PP. In order to considerably improve the impact strength of PP with advantage of elastic modulus enhancement, PP was melt blended with above‐mentioned amounts of OMGM and C15A and different contents of ethylene‐1‐butene copolymer (EBR), 0–10 wt%. The dispersion of low‐ and high‐aspect ratio layered silicate tactoids and EBR nanoparticles in the polymer matrix was studied using transmission electron microscopy. The effect of EBR level on the crystallization behavior, tensile properties, impact strength, and fracture toughness of the resultant toughened hybrid nanocomposite was investigated. The presence of EBR nanoparticles did not show any sufficient effect on the melting and crystallization temperatures of the toughened PP and hybrid nanocomposites. However, the impact results indicated that the addition of EBR to neat PP remarkably increased the toughness while sharply decreased its Young's modulus. The incorporation of 7 wt% EBR in the hybrid nanocomposite containing 1 wt% OMGM and 0.5 wt% C15A considerably enhanced impact strength 119% and 30% in comparison to neat PP and its hybrid nanocomposite, respectively. Additionally, the incorporation of EBR nanoparticle in the presence of the silicate layered nanoparticles prevented significant decreasing in Young's modulus of the matrix. J. VINYL ADDIT. TECHNOL., 25:117–126, 2019. © 2018 Society of Plastics Engineers     

Effect of organic modifiers and silicate type on filler dispersion,thermal, and mechanical properties of ABS‐clay nanocomposites

Acrylonitrile–butadiene–styrene (ABS)–clay composite and intercalated nanocomposites were prepared by melt processing, using Na‐montmorillonite (MMT), several chemically different organically modified MMT (OMMT) and Na‐laponite clays. The polymer–clay hybrids were characterized by WAXD, TEM, DSC, TGA, tensile, and impact tests. Intercalated nanocomposites are formed with organoclays, a composite is obtained with unmodified MMT, and the nanocomposite based on synthetic laponite is almost exfoliated. An unintercalated nanocomposite is formed by one of the organically modified clays, with similar overall stack dispersion as compared to the intercalated nanocomposites. T_g of ABS is unaffected by incorporation of the silicate filler in its matrix upto 4 wt % loading for different aspect ratios and organic modifications. A significant improvement in the onset of thermal decomposition (40–44°C at 4 wt % organoclay) is seen. The Young's modulus shows improvement, the elongation‐at‐break shows reduction, and the tensile strength shows improvement. Notched and unnotched impact strength of the intercalated MMT nanocomposites is lower as compared to that of ABS matrix. However, laponite and overexchanged organomontmorillonite clay lead to improvement in ductility. For the MMT clays, the Young's modulus (E) correlates with the intercalation change in organoclay interlayer separation (Δd₀₀₁) as influenced by the chemistry of the modifier. Although ABS‐laponite composites are exfoliated, the intercalated OMMT‐based nanocomposites show greater improvement in modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Experimental investigation of the influence of the compounding process and the composite composition on the mechanical properties of a short flax fiber–reinforced polypropylene composite

Polypropylene (PP) composites containing 20 wt% short flax fibers are prepared, and the process parameters such as throughput, rotational speed, and screw configuration are varied during melt compounding with a corotating intermeshing twin‐screw extruder. The investigations reveal that low rotational speeds, high throughputs, and moderate shear energy inputs by the screw configuration led to an optimum set of mechanical properties. To investigate the influence of different composite compositions on the mechanical properties, composites with fiber contents between 0 and 40 wt% and maleic anhydride‐grafted PP (PP‐g‐MA) contents between 0 and 7 wt% are prepared. Increasing fiber contents enhance the Young's modulus and decrease the elongation at break and the notched impact strength. The tensile strength is barely affected. The addition of PP‐g‐MA increases the tensile strength as well as the elongation at break, whereas the Young's modulus is not influenced. Thus, PP‐g‐MA enhances the adhesion between PP and flax fibers significantly. POLYM. COMPOS., 36:2282–2290, 2015. © 2014 Society of Plastics Engineers     

Poly(vinyl chloride)/metallic oxides/organically modified montmorillonite nanocomposites: Preparation,morphological characterization,and modeling of the mechanical properties

Poly(vinyl chloride), metallic oxides (from copper, molybdenum, and zinc), and organically modified montmorillonite (O‐MMT) nanocomposites were prepared in a melt‐blending or intercalation‐in‐the‐molten‐state process. The morphology of the nanocomposites was evaluated with X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Properties, such as the mechanical, thermal, and electrical properties, and the dynamic thermal stability against dehydrochlorination were also evaluated. Nanocomposites with a hybrid intercalated/exfoliated structure were obtained in all of the situations considered, as demonstrated by the XRD and TEM results and indirectly by the increment of Young's modulus of the formulations with increasing amount of O‐MMT incorporated. The modeling of Young's modulus by the Halpin–Tsai, Hui–Shia, and Lewis–Nielsen theories showed that the process of nanocomposite preparation allowed the aspect ratio of the clay particles to increase; these values were comparable to those nanocomposites obtained by other researchers with different polymeric matrices and methodologies. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effective mechanical properties of polyvinylalcohol biocomposites with reinforcement of date palm leaf fibers

Polyvinylalcohol/date palm leaf fiber (PVA/DPL) biocomposites were prepared by the melt mixing fabrication technique with various proportions of fibers. DPL fibers were chemically modified with the purpose of improving the dispersion and better compatibility with PVA matrix. Different chemical processes of modification were adopted and the tensile strengths of both treated and untreated fibers were compared. It was noticed that the tensile strength of acrylic acid treated fiber was optimum in comparison to other methods. The interaction of DPL fibers with PVA matrix were studied by Fourier transforms infrared spectroscopy (FTIR). Field emission scanning electron microscope (FESEM) was used to study the morphology of biocomposites. The tensile strength, Young's modulus, elongation at break, flexural strength, and impact strength of PVA/DPL biocomposites were investigated and compared with that of virgin PVA matrix. It was found that the above properties were first increased with fiber loading and then decreased. The optimum properties were obtained at 28 wt% of DPL fiber. The storage modulus and tan delta values of PVA/DPL biocomposites were analyzed. The thermal properties of biocomposites were also studied through the results of thermogravimetric (TGA). POLYM. COMPOS., 34:959–966, 2013. © 2013 Society of Plastics Engineers     

Preparation,characterization, and mechanical properties of poly(ε‐caprolactone)/polylactic acid blend composites

Mechanical properties of poly(ε‐caprolactone) (PCL) and polylactic acid (PLA) blend reinforced with Dura and Tenera palm press fibers were studied. Dicumyl peroxide (DCP) was used as compatibilizer in the blend composites. Fourier transforms infrared spectrophotometer (FTIR) and field emission scanning electron microscope (FESEM) was used to study the effect of treatment on the fibers and fiber/matrix adhesion respectively. The uncompatibilized blend composites exhibited higher Young's modulus than the compatibilized blend composites. Impact strength of compatibilized blend composites of Tenera fibers (FM) increased by 161% at 10 wt% fiber load more than the uncompatibilized blend composites at same fiber load. The Dura fibers (FN) enhanced impact strength by 133% at 10 wt% fiber load. Tensile strength increased by 40% for compatibilized FM blend composites. In conclusion, it was observed that DCP incorporation resulted in good interfacial adhesion as revealed by the FESEM micrographs and evidenced in the improved mechanical properties. POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Isolation and characterization of betel nut leaf fiber: Its potential application in making composites

Betel nut leaf fiber (BNLF) is a new finding as cellulosic filler for polymer composites. Its main constituents are 75% α‐cellulose, 12% hemicelluloses, 10% lignin, and 3% others matter, viscosity average molecular weight 132,000 and degree of crystallinity 70%. In the present work, BNLF reinforced polypropylene (PP) composites were prepared using heat press molding method. 5–20 wt% short length fiber is taken for getting benefits of easy manufacturing and the fiber was chemically treated with NaOH, dicumyl peroxide (DCP), and maleic anhydride‐modified PP (MAPP) to promote the interfacial bond with PP. The extent of modification of fiber was assessed on the basis of morphology, bulk density, moisture absorption, thermal, and mechanical properties of untreated fiber, treated fiber, and their reinforcing PP composites. The tensile and flexural strength of composites increase with the increase of fiber loading up to 10 and 20 wt%, respectively. It was also observed that Young's modulus and flexural modulus increase with fiber loading. The thermal degradation behavior of resulting composites was investigated. Among the various treated fibers, MAPP‐treated fiber composite showed best interfacial interactions as well as mechanical and thermal properties. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Curaua leaf fiber (Ananas comosus var. erectifolius) reinforcing poly(lactic acid) biocomposites: Formulation and performance

Formulations of poly(lactic acid) (PLA) reinforced by curaua leaf fibers were prepared and characterized. This biocomposite has material characteristics such as biodegradability and renewability. This work aimed to develop a PLA/curaua leaf fiber composite as a sustainable biodegradable polymer composite. The PLA and composites were thermally, mechanically, and morphologically evaluated. The critical fiber length was studied to check its influence on the mechanical properties. Predictions of the Young's modulus were done to compare with the experimental data, having a reasonable agreement. The Young's modulus increased above 70%, and the impact strength increased 20% compared with the pure PLA. Thermal analysis showed that formulations with up to 20% by weight of fibers were more thermally stable. The fiber modified the crystallinity of the PLA matrix. The best overall balance of properties was attained in composites containing 15% curaua fiber. POLYM. COMPOS., 36:1520–1530, 2015. © 2014 Society of Plastics Engineers     

Studies of the effect of fiber surface and matrix rheological properties on nonwoven reinforced elastomer composites

The influence of fiber type and fiber-surface properties on matrix flow behavior was investigated using structural reaction injection-molding (SRIM). The influence of fiber type, fiber-surface properties, and matrix type on strength properties in elastomeric composites reinforced with nonwoven fibrous structures was investigated using tensile tests on elastomer composite samples from SRIM and latex coagulation (LC) fabrication methods and the microbond strength method on individual fibers. The fibers used were PET, LLDPE, and p-aramid. Fibers were treated with epoxy, styrene, and isocyanate derivatives, which make the surface chemically reactive. Treatments were also made with NaOH and a copolymer of polyester and polyol ether, causing a change in the fiber surface energy. The matrix types were polyurethane elastomer and natural rubber. The results show that the surface treatments which produced a change in the surface energy influenced the flow rate of the matrix polymer during the composite fabrication process. The treatments resulted in chemically reactive fiber surfaces which improved the fiber-matrix bond strength without affecting the Young's modulus of the composite material. Good correlation was found between bond strength and surface energy including the dispersive component of surface energy in the case of polyurethane elastomer and surface-modified PET fibers. The age of the polyurethane matrix has a marked influence on the bond strength. The fiber volume fraction in composites has a strong influence on the Young's modulus of the elastomer composite. © 1995 John Wiley & Sons, Inc.     

On the structure‐properties relationship in montmorillonite‐filled polyamide 6 nanocomposites

Polyamide 6/montmorillonite (MMT) nanocomposites were prepared by melt compounding method comprising 1–7.5 wt % of Nanomer I.24 TL or 5 and 10 wt % of Cloisite 15A organically modified nanoclays. The composite samples were characterized by synchrotron X‐ray, thermal and FT‐IR spectroscopy methods looking for changes in the micro‐ and nanostructure of both PA6 matrix and MMT reinforcement as a function of the clay content and type. These data were discussed in conjunction with the mechanical properties of the respective nanocomposites. Generally, the Young's modulus was found to increase proportionally to the clay content being the highest in samples with strong aggregation of MMT at micron length scale. The tensile strength passed through a maximum at 2.5 wt % clay load presenting a homogeneous microstructure with almost no agglomeration. Increasing the amount of MMT produced less crystalline PA6 matrices, richer in γ‐PA6 polymorph and resulted in larger long spacings of PA6 due to expansion of both crystalline and amorphous domains. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Effect of Blend Ratio and Draw Ratio on the Mechanical Properties of PET/PP Blended Conjugate Fibers

This study analyzes the influence of blend ratio and draw ratio on the fiber properties of blend fibers composed of poly (ethylene terephthalate), or PET, and polypropylene, or PP, (hereafter referred to as PET/PP conjugate fibers). For a comparison, PET and poly (butylene terephthalate), or PBT blends, (hereafter referred to as PET/PBT conjugate fibers) are also investigated. Various blend ratios of fibers are melt spun and drawn in a multistep drawing method. The conjugate fibers are evaluated using tenacity, Young's modulus, wide-angle X-ray diffraction, differential scanning calorimetry (DSC), and scanning electron microscopy (SEM) tests. The results show that multistep drawing using a lower first-step draw ratio provides a higher tenacity and Young's modulus. Furthermore, when the blend ratio is 75/25 in a PET/PP conjugate fiber and 50/50 in a PET/PBT conjugate fiber, the polymer components undergo a phase inversion phenomenon. A PP sub-micron (10^?1 ～ 10⁰ micron) fiber of about 0.0001 ～ 0.00017 tex in fineness, or about 0.4 ～ 0.5 micron in diameter, can be obtained when PET/PP conjugate fiber is treated with a 25% NaOH aqueous solution by weight. However, A PBT sub-micron fiber cannot be achieved using a PET/PBT conjugate fiber.     

Montmorillonite–multiwalled carbon nanotube nanoarchitecture reinforced thermoplastic polyurethane

Montmorillonite (MMT)–multiwalled carbon nanotube (MWCNT) hybrids were prepared in different weight ratios by simple dry grinding method and characterized. Subsequently, MMT–MWCNT (1:1) hybrid was used as reinforcing filler in developing thermoplastic polyurethane (TPU) nanocomposites by solution blending method. Thermogravimetric analysis showed that 0.25 wt% hybrid‐loaded TPU nanocomposite exhibited maximum enhancement of 31°C corresponding to 50 wt% loss in thermal stability when compared with neat TPU. Differential scanning calorimetry of this composite also indicated that its crystallization and melting temperatures are enhanced by 37 and 13°C, respectively. Mechanical data showed that tensile strength and Young's modulus of 0.50 wt% filled TPU were maximum improved by 57 and 87.5%, respectively. Dynamic mechanical analysis (DMA) measurements indicated 174% (50°C) improvement in storage modulus of 0.50 wt% hybrid‐loaded TPU. Such improvements in thermal and mechanical properties have been attributed to homogeneous dispersion, strong interfacial interaction, and synergistic effect. POLYM. COMPOS., 37:1775–1785, 2016. © 2014 Society of Plastics Engineers     

Enhanced mechanical and thermal properties of polyimide/organically modified montmorillonite hybrid film based on stable poly(amic acid) ammonium salt

In this study, polyimide/organically modified montmorillonite (PI/OMMT) hybrid film was prepared by in situ polymerization from the stable poly(amic acid) ammonium salt/OMMT (PAAS/OMMT) precursor hybrid. PAAS was obtained by incorporating calculated triethylamine into terpolymer poly(amic acid) (PAA), which was synthesized by pyromellitic dianhydride (PMDA), 4,4′‐oxydianiline and p‐phenylenediamine in dimethylacetamide (DMAc). OMMT as a type of layered clays was prepared through surface treatment of montmorillonite (MMT) with 1‐hexadecylamine. Mechanical property measurements of PI/OMMT hybrid film indicated that the addition of 5 wt% of OMMT increased the Young's modulus of PI film up to 11.24 GPa, which is 58% higher than the pristine PI film from PAAS. Besides, the tensile strength increased to 168.36 MPa, which was higher than that of PI film derived from PAA (164.3 MPa) and PI film derived from PAAS (145.2 MPa). Moreover, the thermal stabilities of PI/OMMT hybrid film with appropriate OMMT content were also better than those of original PI films. POLYM. COMPOS., 34:2076–2081, 2013. © 2013 Society of Plastics Engineers     

Nanocomposite fibers of poly(ethylene terephthalate) with montmorillonite and mica: thermomechanical properties and morphology

The thermal stabilities, mechanical properties, and morphologies of nanocomposites of poly(ethylene terephthalate) (PET) with two different organoclays are compared. Dodecyltriphenylphosphonium‐montmorillonite (C₁₂PPh‐MMT) and dodecyltriphenylphosphonium‐mica (C₁₂PPh‐Mica) were used as reinforcing fillers in the fabrication of PET hybrid fibers. The variations of their properties with organoclay content in the polymer matrix and draw ratio (DR) are discussed. Transmission electron microscopy micrographs show that some of the clay layers are dispersed homogeneously within the polymer matrix on the nanoscale, although some clay particles are agglomerated. It was also found that the addition of only a small amount of organoclay is enough to improve the thermal stabilities and mechanical properties of the PET hybrid fibers. Even polymers with low organoclay contents (1–5 wt%) were found to exhibit much higher strength and modulus values than pure PET. In the case of C₁₂PPh‐MMT/PET, the values of the tensile mechanical properties of the hybrid fibers were found to decrease linearly with increases in DR from 1 to 16. However, the tensile mechanical properties of the C₁₂PPh‐Mica hybrid fibers were found to be independent of DR. Copyright © 2006 Society of Chemical Industry     

Combination of double‐modified clay and polypropylene‐graft‐maleic anhydride for the simultaneously improved thermal and mechanical properties of polypropylene

Double‐modified montmorillonite (MMT) was first prepared by covalent modification of MMT with 3‐aminopropyltriethoxysilane and then intercalation modification by tributyl tetradecyl phosphonium ions. The obtained double‐modified MMT was melt compounded with polypropylene (PP) to obtain nanocomposites. The dispersion of the double‐modified MMT in PP was found to be greatly improved by the addition of PP‐graft‐maleic anhydride (PP‐g‐MA) as a “compatibilizer,” whose anhydride groups can react with the amino groups on the surface of the double‐modified MMT platelets and thus improve the dispersion of MMT in PP. Fourier transform infrared, X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis, scanning electron microscopy, and tensile test were used to characterize the structure of the double‐modified MMT, morphology, and the thermal and mechanical properties of the nanocomposites. The results show that PP‐g‐MA promotes the formation of exfoliated/intercalated morphology and obviously increases the thermal properties, tensile strength, and Young's modulus of the PP/double‐modified MMT nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of matrix molecular weight on the dispersion of nanoclay in unmodified high density polyethylene

The effect that polymer molecular weight has on the dispersion of relatively polar montmorillonite (MMT) in nonpolar, unmodified high density polyethylene (HDPE) was examined. Polymer layered silicate (PLS) nanocomposites were prepared via melt compounding in a single screw extruder using three unmodified HDPE matrices of differing molecular weight and organically modified MMT (organoclay) in concentrations ranging from 2 to 8 wt%. The weight average molecular weights (M _W) of the HDPE matrices used ranged from 87,000 to 460,000 g/mol. X‐ray diffraction (XRD), tensile testing, dynamic mechanical thermal analysis (DMTA), and dynamic rheometry were performed on these nanocomposites. Nanocomposites generated from the high molecular weight (HMW) HDPE matrix exhibited increased intercalation of the MMT as shown by XRD and greater improvements in the Young's modulus when compared with nanocomposites generated from the low (LMW) and middle molecular weight (MMW) matrices. DMTA measurements carried out in torsion showed that the increase in shear modulus of the HMW nanocomposites was not as great as that of the LMW and MMW counterparts as observed from a lower percentage enhancement in the storage modulus (G′) and estimated heat distortion temperature (HDT). This was attributed to the higher degree of mechanical anisotropy in the HMW nanocomposites. POLYM. COMPOS., 28:499–511, 2007. © 2007 Society of Plastics Engineers     

Development of a gel spinning process for high‐strength poly(ethylene oxide) fibers

This article describes a new gel‐spinning process for making high‐strength poly(ethylene oxide) (PEO) fibers. The PEO gel‐spinning process was enabled through an oligomer/polymer blend in place of conventional organic solvents, and the gelation and solvent‐like properties were investigated. A 92/8 wt% poly(ethylene glycol)/PEO gel exhibited a melting temperature around 45°C and was highly stretchable at room temperature. Some salient features of a gel‐spun PEO fiber with a draw ratio of 60 are tensile strength at break = 0.66 ± 0.04 GPa, Young's modulus = 4.3 ± 0.1 GPa, and a toughness corresponding to 117 MJ/m³. These numbers are significantly higher than those previously reported. Wide‐angle x‐ray diffraction of the high‐strength fibers showed good molecular orientation along the fiber direction. The results also demonstrate the potential of further improvement of mechanical properties. POLYM. ENG. SCI., 54:2839–2847, 2014. © 2014 Society of Plastics Engineers