40CrNiMoA钢同质焊条焊接接头组织和性能研究

分析了焊接电流70A、80A、90A对40CrNiMoA钢焊缝接头组织和力学性能的影响。随着焊接电流的增大,焊缝外观质量较好。随着焊接电流的增大,熔池区温度升高,奥氏体晶粒尺寸增大,导致马氏体组织粗大。焊缝的显微组织为马氏体及少量残余奥氏体。焊缝的硬度远高于母材的硬度,且波动较大。热影响区的硬度从母材向沿焊缝方向逐渐升高。焊接接头纵向应力在焊缝中心为压应力,向外压应力减小。焊接颜色区边界处纵向应力为拉应力,且该点拉应力最大。焊接接头横向应力在焊缝中心为拉应力,向外逐渐增大,焊接颜色区边界处变横向拉应力达到最大。焊接电流和热输入增大,降低了材料的韧性,组织中铁素体增多及焊接残余应力是诱发脆性断裂的原因。焊接电流80A是40CrNiMoA同质焊条平板对接焊接工艺的最佳的焊接电流。     

焊接速度对机器人搅拌摩擦焊AA7B04铝合金接头组织和力学性能的影响

针对熔化焊在焊接AA7B04铝合金时易在焊缝中出现孔洞等缺陷,且接头性能下降明显、焊后变形大,以及采用铆接等机械连接方式会增加连接件的重量等问题,采用集成了搅拌摩擦焊末端执行器的KUKA Titan机器人对2 mm厚AA7B04高强铝合金进行了焊接,在转速为800 r·min^-1的条件下,研究了焊度对焊接过程中搅拌头3个方向的受力F_x、F_y和F_z的影响.研究发现,F_z受焊速的影响显著,随焊速的增加而降低.利用光学显微镜、透射电子显微镜、拉伸试验、三点弯曲试验和硬度测试等方法,研究了不同焊速下AA7B04铝合金接头的微观组织和力学性能.结果表明：当焊速为100 mm·min^-1时,接头的抗拉强度最高为447 MPa,可达母材的80%,且所有接头的正弯和背弯180°均无裂纹;接头横截面的硬度分布呈W型,硬度最低点出现在热力影响区和焊核区的交界处,焊速不同会导致不同的焊接热循环,且随着焊速的增加接头的硬度随之增加;焊核区组织发生了动态再结晶,生成了细小的等轴晶粒,前进侧和后退侧热力影响区的晶粒均发生了明显的变形;前进侧热影响区析出η'相,后退侧热影响区因温度较高析出η'相和尺寸较大的η相.     

K-TIG焊接中厚板的工艺窗口改进

针对穿孔深熔氩弧焊(K-TIG)工艺焊接8 mm厚Q235低碳钢板时焊接过程不稳定、焊接工艺窗口小等突出问题,首次提出在焊接工件背部铺加保护焊剂的方法改善焊接过程。采用对接焊的方式,在不开坡口、焊接过程不添加焊丝的情况下,达到单面焊双面成形的效果。最终成功的采用430～480 A范围内的直流电流对8 mm厚的Q235低碳钢进行了焊接,将焊接电流窗口扩大到50 A同时也显著的提高了焊接过程的稳定性。同时,在扩大焊接电流窗口之后,系统研究了不同焊接电流下焊接接头的组织性能。研究结果表明:在不同焊接电流下得到的焊接接头中,组织分布以及力学性能分布呈现出相同的状态。焊缝区的组织均由铁素体+珠光体+魏氏组织组成;熔合区由魏氏组织组成;热影响区由铁素体+少量的珠光体组成;此外随着焊接电流的增加,焊接接头背部的熔宽有略微增加;在焊接接头中,熔合区处硬度值最高,其次是焊缝区,之后是热影响区,母材的硬度值最低;焊接接头最终的拉伸断裂位置是在热影响区处。      

热处理对GH3128合金接头组织及力学性能的影响

 核能已经逐渐取代化石能源成为新一代能源,作为重要构件的高温气冷堆中间换热器得到了广泛关注。由于GH3128合金具有较好的焊接性、较高的高温抗氧化性能和组织稳定性,有望成为超高温气冷堆中间换热器的候选材料,但基于换热器结构复杂性以及密封性的要求,焊接是其生产和制造的关键成形手段。采用脉冲钨极氩弧焊(GTAW)对GH3128合金2 mm板材进行对接焊,研究了热处理对焊接焊接接头显微组织以及应力的影响。结果表明,在优化焊接工艺参数下,固溶态板材接头表现出最高的强塑性,室温及高温拉伸断裂位置均为母材。由于热轧态与固溶态板材接头热影响区在焊接过程中产生残余应力,导致该区硬化,在高温变形过程中残余应力诱发热影响区μ相析出,对接头持久、蠕变性能造成不利影响。焊后热处理消除了接头热影响区的残余应力,减少了持久、蠕变过程中μ相的析出,接头持久寿命得以改善。在1 200 ℃下,残余应力可为焊后热处理过程中静态再结晶提供激活能,接头热影响区发生再结晶,硬度下降,接头塑性变形能力不协调,导致室温拉伸与950 ℃拉伸断裂位置均为焊接接头。对固溶态板材试样进行不同的焊后热处理,EBSD扫描结果分析发现,接头经过1 100 ℃×10 min热处理后,残余应力明显消失,温度升高至1 140 ℃后,热影响区开始发生再结晶。     

极薄带钢搭接焊热影响区断带问题分析与改善

针对某连续退火机组0.2 mm及以下极薄规格带钢出现的焊缝热影响区断带问题,结合实物断口形貌分析,从焊缝增厚量、焊接接头金相组织及熔合情况、焊接接头显微硬度分布等不同角度展开研究,确认断带由过渡区域存在未熔合缺陷、焊缝增厚量大、焊接接头硬度分布不均共同导致.通过合理优化工艺参数,加强对焊轮、碾压轮、刷轮等关键部件的精度...     

Investigations on metallurgical and mechanical properties of CO2 laser beam welded Alloy 825

In the research work, an attempt is made to join nickel-based alloy 825 by employing CO₂ laser beam welding. Successful full penetration weld joint of a 5?mm thick plate is achieved with a very low heat input of 120?J-mm^?1. Narrow weld bead width of 0.6?mm at the root and 1.6?mm at the cap is observed fusion zone; the interface and base metal microstructures have been examined using both optical and scanning electron microscopic techniques to understand the microstructural changes which have occurred due to laser welding. A range of tests of Vickers micro hardness, tensile and impact tests had been performed on the weldment to ascertain the mechanical properties of the joint. Tensile failure at the base metal and a 180° root bend test conducted on the weldment ascertain the soundness of the weld joint produced. An attempt is made to correlate the microstructure and mechanical properties of the weldment. Intermetallics TiN and Al₄C₃ observed in the SEM\EDS analysis at the fusion zone are found to have improved the weld metal strength and hardness.     

05CuPCrNi钢等离子弧焊焊接接头的组织与力学性能

 为了研究等离子弧焊在焊接薄板耐候钢时的优越性,对2 mm厚 05CuPCrNi耐大气腐蚀钢分别进行等离子弧焊与MAG焊(熔化极活性气体保护电弧焊)对接焊接,然后对焊接接头分别进行拉伸、弯曲、金相、硬度等试验,通过与MAG焊焊接接头的组织与力学性能对比,结果表明,与MAG焊相比,等离子弧焊时05CuPCrNi耐大气腐蚀钢焊接接头强度相对提高约6%,焊接接头组织为更均匀且细小的铁素体＋珠光体,并无MAG焊中出现的粗大块状铁素体及贝氏体,焊接热影响区较小,焊接接头弯曲性能良好,硬度值及硬度分布情况与MAG相近且无软化现象。     

Process Optimization for Friction-Stir-Welded Martensitic Steel

Advanced high-strength M190 steel sheets were joined by friction-stir welding under different tool rotational and traversing speeds. The optical microstructure of the joints exhibited complete martensite and partial martensite at the weld nugget depending on the cooling rate during welding. The first heat-affected zone outside of the weld nugget revealed ferrite-pearlite phase aggregate, and the second heat-affected zone showed a tempered martensitic structure. The interplay of process variables in terms of peak temperature and cooling rate was studied to observe their effect on joint efficiency under shear testing. The peak hardness at weld nugget was close to the parent alloy at an intermediate cooling rate of 294 to 313 K/s. The lowest hardness was observed at the first heat-affected zone for all welded joints. Joint efficiency was dependent on relative quantity of ferrite-pearlite at first heat-affected zone. In that respect, the intermediate temperature to the tune of ~1193 K to 1273 K (~920 °C to 1000 °C) at the weld nugget was found to be beneficial for obtaining an adequate quantity of pearlite at the first heat-affected zone to provide joint efficiency of more than 50 pct of that of parent alloy.     

Effect of GTAW Parameters on Structure and Mechanical Properties of C86300 Weld Joint

In this study, the effects of heat input variation in gas tungsten arc welding (GTAW), on structure and mechanical properties of commercially C86300 (containing addition of 0.6 wt% silicon) weld joint were investigated. Following microstructural characterization of Base metal, GTAW has been performed at welding currents 50 and 60 A and flow rates of argon shielding gas (10, 14 and 18 l/min) using the same filler metal composition. Therefore six GTAW samples were performed with various welding specifications. By structural investigations and hardness profiles, effects of increasing heat input on increasing average grain size in weld zone, heat affected zone width, penetration depth and alloying element losses were indicated. However increasing heat input increases penetration depth and has a positive effect on hardness and strength of the joint. In considering wear application of this alloy castings and probable GTAW for them, pin-on-disc wear test was performed and revealed better wear resistance of weld metal in comparison with base metal. Hence the optimum values of welding current and argon flow rates (in GTAW with the same composition filler) was determined for this alloy.     

�����������Ӵ���EH40��������ͷ��֯������

Electro-slag welding with heat input of 530kJ/cm was applied to 60mm thick shipbuilding plate EH40, and microstructure and mechanical properties of the weld joint were characterized. Different regions such as heat affected zone, fusion zone, weld metal and base metal are found across the weld joint by microstructure analysis. A narrow coarse grain heat affected zone consisting of acicular ferrite, polygonal ferrite and grain boundary ferrite is found, width of which is less than 1mm. Acicular ferrite (?? 10??m) and grain boundary ferrite is observed at weld metal, while fusion zone have a complex structure of acicular ferrite, grain boundary ferrite and ferrite side plate. Mechanical property tests show that the absorbed energy of WM, FL and CGHAZ at -20?? during Charpy impact test is more than 60J, no evident softening phenomenon occurred at heat affected zone, and other properties met the requirement.     

不同5xxx系焊丝对5182-H111组织和性能的影响

使用3种焊丝ER 5183、ER 5356、ER 5554对6mm 5182-H111铝合金板材进行半自动MIG焊对接试验,通过对焊接接头进行力学性能试验、显微硬度测试及金相组织的观察,探究3种焊丝对5182-H111铝合金组织和性能的影响。结果表明,使用3种焊丝所焊接头中,ER 5183及ER 5356接头抗拉强度均大于ISO 15614-22005要求的焊缝接头系数(1.0),而ER 5554接头焊缝系数仅为0.949;3种焊丝所焊接头硬度均在焊缝区及热影响区有所降低,其中ER 5356所焊接头焊缝强度较其他两种焊丝焊缝区硬度高,为85.5HV;3种焊丝所焊接头组织形貌相近,均存在β(Mg2Al3)强化相,但由于ER 5183与ER 5356焊丝中含有更多的Mg,因此生成了更多的β(Mg2Al3)相,使得焊缝组织更加致密。     

Microstructural factors governing hardness in friction-stir welds of solid-solution-hardened Al alloys

Microstructural factors governing hardness in friction-stir welds of the solid-solution-hardened Al alloys 1080 and 5083 were examined by optical microscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The effect of grain boundary on the hardness was examined in an Al alloy 1080 which did not contain any second-phase particles. The weld of Al alloy 1080 had a slightly greater hardness in the stir zone than the base material. The maximum hardness was located in the thermomechanically affected zone (TMAZ). The stir zone consisted of recrystallized fine grains, while the TMAZ had a recovered grain structure. The increase in hardness in the stir zone can be explained by the Hall-Petch relationship. On the other hand, the hardness profiles in the weld of Al alloy 5083 were roughly homogeneous. Friction-stir welding created the fine recrystallized grains in the stir zone and recovered grains in the TMAZ in the weld of this alloy. The stir zone and the TMAZ had slightly higher dislocation densities than the base material. Many small Al₆(Mn,Fe) particles were detected in all the grains of the weld. The hardness profiles could not be explained by the Hall-Petch relationship, but rather by Orowan hardening. The results of the present study suggest that the hardness profile is mainly affected by the distribution of small particles in friction-stir welds of Al alloys containing many such particles.     

Microstructure and Fatigue Properties of a Friction Stir Lap Welded Magnesium Alloy

Friction stir welding (FSW), being an enabling solid-state joining technology, can be suitably applied for the assembly of lightweight magnesium (Mg) alloys. In this investigation, friction stir lap welded (FSLWed) joints of AZ31B-H24 Mg alloy were characterized in terms of the welding defects, microstructure, hardness, and fatigue properties at various combinations of tool rotational rates and welding speeds. It was observed that the hardness decreased from the base metal (BM) to the stir zone (SZ) across the heat-affected zone (HAZ) and thermomechanically affected zone (TMAZ). The lowest value of hardness appeared in the SZ. With increasing tool rotational rate or decreasing welding speed, the average hardness in the SZ decreased owing to increasing grain size, and a Hall–Petch-type relationship was established. Fatigue fracture of the lap welds always occurred at the interface between the SZ and TMAZ on the advancing side where a larger hooking defect was present (in comparison with the retreating side). The welding parameters had a significant influence on the hook height and the subsequent fatigue life. A relatively “cold” weld, conducted at a rotational rate of 1000 rpm and welding speed of 20 mm/s, gave rise to almost complete elimination of the hooking defect, thus considerably (over two orders of magnitude) improving the fatigue life. Fatigue crack propagation was basically characterized by the formation of fatigue striations concomitantly with secondary cracks.     

国产A6N01铝合金型材MIG焊接头的微观组织与力学性能

利用金相观察、显微硬度测定、拉伸和弯曲性能测试等方法研究了A6N01-T5铝合金型材MIG焊接接头的显微组织和力学性能.结果表明：焊接接头焊缝中心金属为明显的激冷形成的铸态组织,呈等轴晶状;熔合区靠近焊缝侧的结晶形态为沿散热方向排列的柱状晶,邻近熔合区的热影响区晶粒粗化.焊缝中心处具有较高的显微硬度,在距离焊缝中心10~12 mm处的热影响区显微硬度值最低.国产A6N01-T5铝合金型材焊接接头抗拉强度达到欧洲标准DIN EN 288-4的要求.     

2A97铝锂合金搅拌摩擦焊焊缝的微观组织特征

对厚度为25 mm的T851态2A97铝锂合金进行搅拌摩擦焊焊接,利用显微硬度、金相显微镜(OM)和透射电镜(TEM)等对焊缝的显微硬度和微观组织进行研究.结果表明:接头基材硬度最高,热影响区和热机影响区硬度降低,焊缝中心硬度又升高,硬度最低位置在热影响区.焊核区发生动态再结晶,形成细小等轴的晶粒;焊核区S′相全部溶解,T1相儿乎全部溶解,在随后的冷却和时效过程中,焊核区析出GP区和细小弥散的δ′相;热影响区的T1相部分溶解,S′相全部溶解,析出θ"相、δ′相和δ′/β′的复合相.     

Q550D高强度钢板组织及焊接性能分析

包钢通过成分优化和轧制工艺的优化研制了工程机械用高强度钢Q550D。通过热影响区最高硬度、插销试验、斜Y坡口焊接裂纹试验对Q550D高强度钢的焊接性能进行分析,研究结果表明:Q550D钢板热影响区最高硬度(HV10)为297。插销试验结果表明,在中等拘束条件下,采用HS-70焊丝焊接20 mm厚Q550D钢板,不预热没有裂纹的产生。同时斜Y坡口焊接裂纹试验表明对于20 mm厚Q550D钢板,在不预热条件下焊接,两组试样表面裂纹率和断面裂纹率均为零。     

Mechanical Properties of Friction Stir Welded Cast Al–Mg–Sc Alloys

Friction Stir (FS) welding promises joints with low porosity, fine microstructures, and low vaporization of volatile elements compared with conventional welding techniques. FS weld was carried out on Vacuum Induction Melted 5?mm thick cast Aluminum?CMagnesium?CScandium (Al?CMg?CSc) alloy plates. Microstructural evaluation revealed that due to FS welding, fine and fragmented dynamically recrystallized grains have been formed in the weld nugget. Tensile fracture occurred out side the weld zone. The tensile strength of the welded joint is more than the cast base metal. The hardness of the FS welded joint is less than the hardness of the cast base metal. The minimum hardness was located on the retreating side of the weld. These results clearly show that FSW process is amenable to join cast Al?CMg?CSc alloy.     

Dissimilar Laser Joining of NiTi SMA and MP35N Wires

The laser welding of NiTi alloy wire to MP35N wire was investigated to improve the understanding of dissimilar materials joining of NiTi shape memory alloys (SMAs), facilitating their future application in novel devices. Both positioning of the laser beam with respect to the joint’s centerline and laser peak power were found to be critical variables affecting the physical and thermomechanical properties of the welded joint. Positioning of the laser beam was used to control the weld pool composition, while the laser beam intensity affected the pool size and mixing. These variables were shown to greatly affect hardness and susceptibility to cracking in the fusion zone, which heavily impacted the weld strength. With a lower peak power and the laser positioned over the MP35N wire, butt-welded wire joints were achieved with the ultimate load of 66 pct of the NiTi wire breaking load.     

Investigations on Dissimilar Weld of UNS S32205 DSS and ASTM A517 Steel

In the present research, microstructure and mechanical properties of 2205 duplex stainless steel/A517 quench and tempered low alloy steel dissimilar joint were investigated. For this purpose, gas tungsten arc welding was used with ER2209 filler metal. Characterizations were conducted by optical microscopy, scanning electron microscopy equipped with an energy dispersive spectroscopy and X-ray diffraction. Mechanical properties were evaluated in micro-hardness, tensile and impact tests. Microstructure in the weld zone included an austenitic continuous network in the matrix of primary ferrite. No brittle phases were formed in the weld metal and stainless steel heat affected zone (HAZ). The weld metal/A517 interface showed higher hardness than other regions. Tensile tests indicated that the values of the yield and tensile strength were 663 and 796 MPa, respectively. Impact tests indicated that the weld zone had almost the same impact energy as base metals. The minimum impact energy of 12 J was related to A517 HAZ. The results of scanning electron microscopy for fracture surfaces indicated that weld zone, 2205 HAZ and A517 HAZ had ductile, ductile–brittle and brittle fracture mode, respectively.     

Nb、Ti微合金化对Q345R压力容器板焊接性能的影响

 通过力学性能测试及微观组织分析研究了传统中板及低碳,Nb-Ti微合金化Q345R热连轧压力容器板在手工焊、气保焊及埋弧焊3种焊接工艺下的接头性能,测定了不同焊接工艺下接头各区域的硬度分布,评价了Q345R接头力学性能。试验结果表明,连轧Q345R板焊接接头具有更好的综合性能,其接头冲击韧性明显好于传统中板,粗晶区淬硬程度低。连轧板良好的性能来源于TMCP工艺下碳当量降低及Nb-Ti微合金化处理改善了基体及接头的微观组织。