Effect of orotic acid as a nucleating agent on the crystallization of bacterial poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) copolymers

The kinetics of crystallization induced by orotic acid (OA) and boron nitride (BN) as nucleating agents were investigated for bacterial poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s (P(HB‐co‐HH)s) containing from 0 to 18% HH monomer units. The nucleation efficiency of these two chemicals was investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that both orotic acid and boron nitride are able to nucleate the crystallization of PHB. In the case of P(HB‐co‐HH) copolymers, orotic acid showed an outstanding nucleating effect. The comparison of half‐crystallization times shows that for P(HB‐co‐10% HH), the crystallization initiated by orotic acid is more than three time faster than the one induced by boron nitride (t_1/2BN/t_1/2OA(60°C) = 3.7 and t_1/2BN/t_1/2OA(90°C) = 4.5). According to the fact that orotic acid is a biodegradable, biocompatible and a nontoxic chemical, this nucleating agent is a promising solution for PHAs used in medical applications such as implants. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Improvement in the mechanical properties of poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) by preorientation

Preoriented poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (Nodax?) films were obtained via the drawing of films to prestretching ratios ranging from 200 to 1000%. As expected, preorientation resulted in substantial improvements in the mechanical properties of the films from the corresponding increases in the amount and nature of the crystallinity present. Stress–strain curves in elongation showed a yield peak, which was relatively broad for the unoriented samples but became sharper, with a well‐defined neck, as the extent of preorientation was increased. In addition, the preoriented films had higher modulus, toughness, yield stress, and tensile strength values. The attribution of these changes in the mechanical properties to changes in the crystallinity was supported by X‐ray diffraction measurements. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2257–2262, 2004     

Crystallization kinetics and melting behaviour of microbial poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)

Isothermal and non‐isothermal crystallization kinetics of microbial poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(3HB‐3HHx)] was investigated by differential scanning calorimetry (DSC) and ¹³C solid‐state nuclear magnetic resonance (NMR). Avrami analysis was performed to obtain the kinetic parameters of primary crystallization. The results showed that the Avrami equation was suitable for describing the isothermal and non‐isothermal crystallization processes of P(3HB‐3HHx). The equilibrium melting temperature of P(3HB‐3HHx) and its nucleation constant of crystal growth kinetics, which were obtained by using the Hoffman–Weeks equation and the Lauritzen–Hoffmann model, were, respectively, 121.8 °C and 2.87 × 10⁵ K² when using the empirical ‘universal’ values of U* = 1500 cal mol^?1. During the heating process, the melting behaviour of P(3HB‐3HHx) for both isothermal and non‐isothermal crystallization showed multiple melting peaks, which was the result of melting recrystallization. The lower melting peak resulted from the melting of crystals formed during the corresponding crystallization process, while the higher melting peak resulted from the recrystallization that took place during the heating process. Copyright © 2005 Society of Chemical Industry     

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) and poly(styrene‐co‐acrylonitrile)

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) and poly(styrene‐co‐acrylonitrile) (SAN) prepared by solution casting were investigated by differential scanning calorimetry. In the study of PHBV‐SAN blends by differential scanning calorimetry, glass transition temperature and melting point of PHBV in the PHBV‐SAN blends were almost unchanged compared with those of the pure PHBV. This result indicates that the blends of PHBV and SAN are immiscible. However, crystallization temperature of the PHBV in the blends decreased approximately 9–15°. From the results of the Avrami analysis of PHBV in the PHBV‐SAN blends, crystallization rate constant of PHBV in the PHBV‐SAN blends decreased compared with that of the pure PHBV. From the above results, it is suggested that the nucleation of PHBV in the blends is suppressed by the addition of SAN. From the measured crystallization half time and degree of supercooling, interfacial free energy for the formation of heterogeneous nuclei of PHBV in the PHBV‐SAN blends was calculated and found to be 2360 (mN/m)³ for the pure PHBV and 2920–3120 (mN/m)³ for the blends. The values of interfacial free energy indicate that heterogeneity of PHBV in the PHBV‐SAN blends is deactivated by the SAN. This result is consistent with the results of crystallization temperature and crystallization rate constant of PHBV in the PHBV‐SAN blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 673–679, 2000     

Fast crystallization of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with talc and boron nitride as nucleating agents

The crystallization behavior of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) induced by two kinds of nucleating agents, boron nitride (BN) and talc, was investigated by differential scanning calorimetry, polarized optical microscopy and X‐ray diffraction. Both BN and talc have good nucleating ability in the crystallization of PHB and PHBV. From these results, combined with molecular weight measurement by gel permeation chromatography, the mechanism of nucleation by BN and talc in the crystallization of PHB and PHBV has been proposed. BN acts as a nucleating agent itself and initiates nucleation in the crystallization of PHB and PHBV. Talc acts in a different way. It reacts as a chemical reagent with the molten chains of PHB/PHBV, while the reaction product acts as the true nucleating agent, which lowers the crystallization barriers of PHB and PHBV. ¹H NMR spectroscopy provides evidence for the reaction between PHB and talc and supports the proposed nucleation mechanism. Copyright © 2005 Society of Chemical Industry     

Water transport properties in poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) biopolymers

Water sorption and diffusion have been investigated in poly(3‐hydroxybutyrate) (PHB) and three poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) copolymers [P(HB‐HV)] by means of a Cahn electromicrobalance. Permeability of these samples have been determined using a gravimetric permeation cell. Two experimental setups were used for the gravimetric sorption measurements, under dynamic and static conditions, respectively. The differences observed in the results obtained using these techniques are discussed. The sorption measurements have evidenced the tendency of water molecules to form aggregates or clusters in the polymer. In addition, the static sorption method revealed the potential of PHB and P(HB‐HV) to undergo molecular relaxations, eventually leading to a partial desorption of the previously sorbed water after an induction period. The clustering effect was adequately described by the polycondensation model. On the other hand, the interpretation of the diffusivity in terms of mobility coefficients has revealed a competition between a plasticization effect and clustering. As a whole, water transport properties in PHB and its copolymers can be considered to be very close in magnitude to those of common thermoplastics such as PVC and PET. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 455–468, 1999     

Thermogravimetric analysis of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

The thermal degradation of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐HV)] was studied using thermogravimetry (TG). In the thermal degradation of PHB, the temperature at the onset of weight loss (T_o) was derived by T_o = 0.97B + 259, where B represents the heating rate (°C/min). The temperature at which the weight loss rate was maximum (T_p) was T_p = 1.07B + 273, and the final temperature (T_f) at which degradation was completed was T_f = 1.10B + 280. The percentage of the weight loss at temperature T_p (C_p) was 69 ± 1% whereas the percentage of the weight loss at temperature T_f (C_f) was 96 ± 1%. In the thermal degradation of P(HB‐HV) (7:3), T_o = 0.98B + 262, T_p = 1.00B + 278, and T_f = 1.12B + 285. The values of C_p and C_f were 62 ± 7 and 93 ± 1%, respectively. The derivative thermogravimetric (DTG) curves of PHB confirmed only one weight loss step change because the polymer mainly consisted of the HB monomer only. The DTG curves of P(HB‐HV), however, suggested multiple weight loss step changes; this was probably due to the different evaporation rates of the two monomers. The incorporation of 10 and 30 mol % of the HV component into the polyester increased the various thermal temperatures (T_o, T_p, andT_f) by 7–12°C (measured at B = 20°C/min). © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2237–2244, 2001     

Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with high molecular weight poly(lactic acid) blends determined by thermal analysis

An important strategy used in the polymer industry in recent years is blending two bio‐based polymers to attain desirable properties similar to traditional thermoplastics, thus increasing the application potential for bio‐based and bio‐degradable polymers. Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) with poly(L ‐lactic acid) (PLA) were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). Three different grades of commercially available PLAs and one type of PHBV were blended in different ratios of 50/50, 60/40, 70/30, and 80/20 (PHBV/PLA) using a micro‐compounder at 175°C. The DSC and TGA analysis showed the blends were immiscible due to different stereo configuration of PLA polymer and two distinct melting temperatures. However, some compatibility between PHBV and PLA polymers was observed due to decreases in PLA's glass transition temperatures. Additionally, the blends do not show clear separation by SEM analysis, as observed in the thermal analysis. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of nucleating agents on the crystallization of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

The effect of nucleating agents on the crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) was studied. A differential scanning calorimeter was used to monitor the energy of the crystallization process from the melt and melting behavior. During the crystallization process from the melt, nucleating agent led to an increase in crystallization temperature (T_c) of PHBV compared with that for plain PHBV (without nucleating agent). The melting temperature of PHBV changed little with addition of nucleating agent. However, the areas of two melting peaks changed considerably with added nucleating agent. During isothermal crystallization, dependence of the relative degree of crystallization on time was described by the Avrami equation. The addition of nucleating agent caused an increase in the overall crystallization rate of PHBV, but did not influence the mechanism of nucleation and growth of the PHB crystals. The equilibrium melting temperature of PHBV was determined as 187°C. Analysis of kinetic data according to nucleation theories showed that the increase in crystallization rate of PHBV in the composite is due to the decrease in surface energy of the extremity surface. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2145–2152, 2002     

Tailoring the surface architecture of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) scaffolds

This study was designed to determine whether the surface modifications of the various poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐co‐4HB)] copolymer scaffolds fabricated would enhance mouse fibroblast cells (L929) attachment and proliferation. The P(3HB‐co‐4HB) copolymer with a wide range of 4HB monomer composition (16–91 mol %) was synthesized by a local isolate Cupriavidus sp. USMAA1020 by employing the modified two‐stage cultivation and by varying the concentrations of 4HB precursors, namely γ‐butyrolactone and 1,4‐butanediol. Five different processing techniques were used in fabricating the P(3HB‐co‐4HB) copolymer scaffolds such as solvent casting, salt‐leaching, enzyme degradation, combining salt‐leaching with enzyme degradation, and electrospinning. The increase in 4HB composition lowered melting temperatures (T_m) but increased elongation to break. P(3HB‐co‐91 mol % 4HB) exhibited a melting point of 46°C and elongation to break of 380%. The atomic force analysis showed an increase in the average surface roughness as the 4HB monomer composition increased. The mouse fibroblasts (L929) cell attachment was found to increase with high 4HB monomer composition in copolymer scaffolds. These results illustrate the importance of a detailed characterization of surface architecture of scaffolds to provoke specific cellular responses. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of lignin particles as a nucleating agent on crystallization of poly(3‐hydroxybutyrate)

The effect of lignin fine powder, as a new kind of nucleating agent, on the crystallization process of poly(3‐hydroxybutyrate) (PHB) was studied. The kinetics of both isothermal and nonisothermal crystallization processes from the melt for both pure PHB and PHB/lignin blend was studied by means of differential scanning calorimetry. Lignin shortened the crystallization half‐time t_1/2 for isothermal crystallization. The activation energy ΔE for PHB/lignin and pure PHB in the isothermal crystallization process was ?237.40 and ?131.22 kJ/mol, respectively, clearly indicating that the crystallization of the PHB/lignin blend was more favorable than that of pure PHB from a thermodynamic perspective. At the same time, according to polarized optical microscopy, the rate of spherulitic growth from the melt increased with the addition of lignin, which is ascribed to the reduction of surface fold energy σ_e, that is, σ_e is 59.2 × 10^?3 and 41.6 × 10^?3 J m^?2 for pure PHB and PHB/lignin, respectively. Polarized optical microscopy also showed that the spherulites found in PHB with lignin were smaller in size and greater in number than those found in pure PHB. The wide‐angle X‐ray diffraction indicated that an addition of lignin caused no change in the crystal structure and degree of crystallinity. These results indicated that lignin is a good nucleating agent for the crystallization of PHB. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2466–2474, 2004     

Drug release from electrospun fibers of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) grafted with poly(N‐vinylpyrrolidone)

Poly(N‐vinylpyrrolidone) (PVP) groups were grafted onto poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) backbone to modify the properties of PHBV and synthesize a new novel biocompatible graft copolymer. Based on these graft copolymers, electrospun fiber mats and commonly cast films were explored as drug delivery vehicles using tetracycline hydrochloride as a model drug. Toward that end, the fibers were electrospun and the films were cast from chloroform solutions containing a small amount of methanol to solubilize the drug. The Brookfield viscosities of the solution were determined to achieve the optimal electrospinning conditions. The vitro release of the tetracycline hydrochloride from these new drug delivery systems was followed by UV–vis spectroscopy. To probe into the factors affected on the release behavior of these drug delivery systems, their water absorbing abilities in phosphate buffer solution were investigated, together with their surface hydrophilicity, porosity and crystallization properties were characterized by water contact angles, capillary flow porometer, DSC, and WAXD, respectively. The morphological changes of these drug delivery vehicles before and after release were also observed with SEM. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of graft modification with poly(N‐vinylpyrrolidone) on thermal and mechanical properties of poly (3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

Poly(N‐vinylpyrrolidone) (PVP) groups were grafted onto poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) backbone to modify the properties of PHBV and synthesize a new novel biocompatible graft copolymer. The effect of graft modification with PVP on the thermal and mechanical properties of PHBV was investigated. The thermal stability of grafted PHBV was remarkably improved while the melting temperature (T_m) was almost not affected by graft modification. The isothermal crystallization behavior of samples was observed by polarized optical microscopy and the results showed that the spherulitic radial growth rates (G) of grafted PHBV at the same crystallization temperature (T_c) decreased with increasing graft yield (graft%) of samples. Analysis of isothermal crystallization kinetics showed that both the surface free energy (σ_e) and the work of chain‐folding per molecular fold (q) of grafted PHBV increased with increasing graft%, implying that the chains of grafted PHBV are less flexible than ungrafted PHBV. This conclusion was in agreement with the mechanical testing results. The Young's modulus of grafted PHBV increased while the elongation decreased with increasing graft%. The hydrophilicity of polymer films was also investigated by the water contact angle measurement and the results revealed that the hydrophilicity of grafted PHBV was enhanced. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal analysis of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) irradiated under vacuum

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) was irradiated by ⁶⁰Co γ‐rays (doses of 50, 100 and 200 kGy) under vacuum. The thermal analysis of control and irradiated PHBV, under vacuum was carried out by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The tensile properties of control and irradiated PHBV were examined by using an Instron tensile testing machine. In the thermal degradation of control and irradiated PHBV, a one‐step weight loss was observed. The derivative thermogravimetric curves of control and irradiated PHBV confirmed only one weight‐loss step change. The onset degradation temperature (T_o) and the temperature of maximum weight‐loss rate (T_p) of control and irradiated PHBV were in line with the heating rate (°C min^?1). T_o and T_P of PHBV decreased with increasing radiation dose at the same heating rate. The DSC results showed that ⁶⁰Co γ‐radiation significantly affected the thermal properties of PHBV. With increasing radiation dose, the melting temperature (T_m) of PHBV shifted to a lower value, due to the decrease in crystal size. The tensile strength and fracture strain of the irradiated PHBV decreased, hence indicating an increased brittleness. Copyright © 2004 Society of Chemical Industry     

Carbon dioxide sorption and diffusion in poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐CO‐3‐hydroxyvalerate)

CO₂ sorption and diffusion in poly(3‐hydroxybutyrate) and three poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) copolymers were investigated gravimetrically at temperatures from 25° to 50°C and pressures up to 1 atm. The sorption behavior proved to be linear for all the copolymers studied. An additional set of measurements performed in a pressure decay apparatus at 35°C showed that the linearity could be extrapolated to pressures up to 25 atm. The sorption results obtained from both techniques were in good agreement. The poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) sorption kinetics were increasingly non‐Fickian at the higher temperatures, thus preventing the calculation of diffusion coefficients above 35°C. Interestingly, this was not the case for poly(3‐hydroxybutyrate), and diffusion coefficients and permeabilities could be calculated at all of the investigated temperatures. The 35°C permeabilities were fairly low, which is attributed to the high degree of crystallinity of this polyester family. Finally, the poly(3‐hydroxybutyrate) barrier properties against CO₂ are successfully compared with those of some selected common thermoplastics. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2391–2399, 1999     

Miscibility and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ poly(methyl methacrylate) blends

The miscibility and crystallization kinetics of the blends of random poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐co‐HV)] copolymer and poly(methyl methacrylate) (PMMA) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PMMA blends were miscible in the melt. Thus the single glass‐transition temperature (T_g) of the blends within the whole composition range suggests that P(HB‐co‐HV) and PMMA were totally miscible for the miscible blends. The equilibrium melting point (T°_m) of P(HB‐co‐HV) in the P(HB‐co‐HV)/PMMA blends decreased with increasing PMMA. The T°_m depression supports the miscibility of the blends. With respect to the results of crystallization kinetics, it was found that both the spherulitic growth rate and the overall crystallization rate decreased with the addition of PMMA. The kinetics retardation was attributed to the decrease in P(HB‐co‐HV) molecular mobility and dilution of P(HB‐co‐HV) concentration resulting from the addition of PMMA, which has a higher T_g. According to secondary nucleation theory, the kinetics of spherulitic crystallization of P(HB‐co‐HV) in the blends was analyzed in the studied temperature range. The crystallizations of P(HB‐co‐HV) in P(HB‐co‐HV)/PMMA blends were assigned to n = 4, regime III growth process. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3595–3603, 2004     

Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/poly(vinyl acetate) blends

The miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (P(HB‐co‐HV))/poly(vinyl acetate) (PVAc) blends have been investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PVAc blends were miscible in the melt over the whole compositions. Thus the blend exhibited a single glass transition temperature (T_g), which increased with increasing PVAc composition. The spherulitic morphologies of P(HB‐co‐HV)/PVAc blends indicated that the PVAc was predominantly segregated into P(HB‐co‐HV) interlamellar or interfibrillar regions during P(HB‐co‐HV) crystallization because of the volume‐filled spherulites. As to the crystallization kinetics study, it was found that the overall crystallization and crystal growth rates decreased with the addition of PVAc. The kinetics retardation was primarily attributed to the reduction of chain mobility and dilution of P(HB‐co‐HV) upon mixing with higher T_g PVAc. The overall crystallization rate was predominantly governed by the spherulitic growth rate and promoted by the samples treated with the quenched state because of the higher nucleation density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 980–988, 2006     

Influence of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) on miscibility and properties of atactic poly(methyl methacrylate)

Miscibility and properties of two atactic poly(methyl methacrylate)‐based blends [containing 10 and 20% of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)] have been investigated as a function of thermal treatments. Differential scanning calorimetry and dynamic mechanical thermal analysis of blends quenched in liquid nitrogen or ice/water, after annealing at T > 190 °C, showed a single glass transition temperature, indicating miscibility of the components for the time‐temperature history. Two glass transition temperatures, equal to those of the pure components, are instead found for blends after annealing at T < 190 °C. Scanning electron microscopy confirmed the homogeneity for the former quenched blends and phase separation for the latter. These results indicate the presence of an upper critical solution temperature (UCST). Tensile experiments, performed on two series of samples annealed at temperatures above and below the UCST, showed that the copolyester induces a decrease of Young's modulus and stresses at yielding and break points, and a marked increase of elongation at break. Differences in tensile properties between the two series of annealed blends are accounted for by the physical state of the components at room temperature after annealing above or below the UCST. Copyright © 2004 Society of Chemical Industry