Novel ternary blends of natural rubber/linear low-density polyethylene/thermoplastic starch: influence of epoxide level of epoxidized natural rubber on blend properties

Novel degradable materials based on ternary blends of natural rubber (NR)/linear low-density polyethylene (LLDPE)/thermoplastic starch (TPS) were prepared via simple blending technique using three different types of natural rubber (i.e., unmodified natural rubber (RSS#3) and ENR with 25 and 50 mol% epoxide). The evolution of co-continuous phase morphology was first clarified for 50/50: NR/LLDPE blend. Then, 10 wt% of TPS was added to form 50/40/10: NR/LLDPE/TPS ternary blend, where TPS was the particulate dispersed phase in the NR/LLDPE matrix. The smallest TPS particles were observed in the ENR-50/LLDPE blend. This might be attributed to the chemical interactions of polar functional groups in ENR and TPS that enhanced their interfacial adhesion. We found that ternary blend of ENR-50/LLDPE/TPS exhibited higher 100 % modulus, tensile strength, hardness, storage modulus, complex viscosity and thermal properties compared with those of ENR-25/LLDPE/TPS and RSS#3/LLDPE/TPS ternary blends. Furthermore, lower melting temperature (T _m) and heat of crystallization of LLDPE (?H) were observed in ternary blend of ENR-50/LLDPE/TPS compared to the other ternary blends. Also, neat TPS exhibited the fastest biodegradation by weight loss during burial in soil for 2 or 6 months, while the ternary blends of NR/LLDPE/TPS exhibited higher weight loss compared to the neat NR and LLDPE. The lower weight loss of the ternary blends with ENR was likely due to the stronger chemical interfacial interactions. This proved that the blend with ENR had lower biodegradability than the blend with unmodified NR.     

Quantitative characterization of interfaces in rubber–rubber blends by means of modulated‐temperature DSC

Rubber–rubber blends are used widely in industry, for example, in tire manufacture. It is often difficult to characterize interfaces in such rubber–rubber blends quantitatively because of the similarity in the chemical structure of the component rubbers. Here, a new method was suggested for the measurement of the weight fraction of the interface in rubber–rubber blends using modulated‐temperature differential scanning calorimetry (M‐TDSC). Quantitative analysis using the differential of the heat capacity, dCp/dT, versus the temperature signal from M‐TDSC allows the weight fraction of the interface to be calculated. As examples, polybutadiene rubber (BR)–natural rubber (NR), BR–styrene‐co‐butadiene rubber (SBR), SBR–NR, and nitrile rubber (NBR)–NR blend systems were analyzed. The interfacial content in these blends was obtained. SBR is partially miscible with BR. The cis‐structure content in BR has an obvious effect on the extent of mixing in the SBR–BR blends. With increasing styrene content in the SBR in the SBR–BR blends, the interface content decreases. NR is partially miscible with both BR and SBR. The NBR used in this research is essentially immiscible with NR. The maximum amount of interface was found to be at the 50:50 blend composition in BR–NR, SBR–BR, and SBR–NR systems. Quantitative analysis of interfaces in these blend systems is reported for the first time. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1791–1798, 2000     

Thermoplastic natural rubber based on polyamide‐12: Influence of blending technique and type of rubber on temperature scanning stress relaxation and other related properties

Thermoplastic natural rubber based on polyamide‐12 (PA‐12) blend was prepared by melt blending technique. Influence of blending techniques (i.e., simple blend and dynamic vulcanization) and types of natural rubber (i.e., unmodified natural rubber (NR) and epoxidized natural rubber (ENR)) on properties of the blends were investigated. It was found that the simple blends with the proportion of rubber ～ 60 wt % exhibited cocontinuous phase structure while the dynamically cured blends showed dispersed morphology. Furthermore, the blend of ENR exhibited superior mechanical properties, stress relaxation behavior, and fine grain morphology than those of the blend of the unmodified NR. This is attributed to chemical interaction between oxirane groups in ENR molecules and polar functional groups in PA‐12 molecules which caused higher interfacial adhesion. It was also found that the dynamic vulcanization caused enhancement of strength and hardness properties. Temperature scanning stress relaxation measurement revealed improvement of stress relaxation properties and thermal resistance of the dynamically cured ENR/PA‐12 blend. This is attributed to synergistic effects of dynamic vulcanization of ENR and chemical reaction of the ENR and PA‐12 molecules. Furthermore, the dynamically cured ENR/PA‐12 blend exhibited smaller rubber particles dispersed in the PA‐12 matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Study on the milling behavior of chloroprene rubber blends with ethylene–propylene–diene monomer rubber,polybutadiene rubber,and natural rubber

The viscoelastic properties of the blends of chloroprene rubber (CR) with ethylene–propylene–diene monomer rubber (EPDM), polybutadiene rubber (BR), and natural rubber (NR) at different temperature were studied using rubber processing analyzer (RPA). Mooney viscosities of compounds were measured and tight milling and sheeting appearance were observed on a two‐roll mill. The results showed that Mooney viscosities and the elastic modulus of the blends decreased with the increase of the temperature from 60 to 100°C. And the decreasing trends of pure CR, pure NR, and CR/NR blend compounds were more prominent than that of pure EPDM, pure BR, CR/EPDM, and CR/BR blend compounds. For CR/EPDM blend compounds, the decreasing trend became slower with the increase of EPDM ratio in the blend. Compared with pure CR, pure NR and CR/NR blend compounds, pure EPDM, pure BR compounds, and the blend compounds of CR/EPDM and CR/BR showed less sensibility to temperature and they were less sticky to the metal surface of rolls and could be kept in elastic state at higher temperature, easy to be milled up and sheeted. At the same blend ratio and temperature, the property of tight milling of the blends decreased in the sequence of CR/EPDM, CR/BR, and CR/NR. With the increase of EPDM, BR, or NR ratio in CR blends, its property of tight milling was improved. POLYM. COMPOS., 28:667–673, 2007. © 2007 Society of Plastics Engineers     

Effects of epoxidized natural rubber (ENR‐50) and processing parameters on the properties of NR/EPDM blends using response surface methodology

The effects of epoxidized natural rubber (ENR‐50) and processing parameters on the properties of natural rubber/ethylene–propylene–diene rubber (NR/EPDM; 70 : 30 phr) blends were studied. The compounds were prepared by melt compounding method. Using response surface methodology of two‐level full factorial, the effects of ENR‐50 contents (?1 : 5 phr; +1 : 10 phr), mixing temperature (?1 : 50°C; +1 : 110°C), rotor speed (?1 : 40 rpm; +1 : 80 rpm), and mixing time (?1 : 5 min; +1 : 9 min) in NR/EPDM blends were evaluated. Cure characteristics and tensile properties were selected as the responses. The significance of factors and its interaction was analyzed using ANOVA and the model's ability to represent the system was confirmed using the constant of determination, R² with values above 0.90. It was found that the presence of ENR‐50 has the predominant role on the properties of NR/EPDM blends. The addition of ENR‐50 significantly improved cure characteristics and tensile strength up to 5.12% and 6.48% compared to neat NR/EPDM blends, respectively. These findings were further supported by swell measurement, differential scanning calorimetry, and scanning electron microscopy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40713.     

Novel thermoplastic natural rubber based on thermoplastic polyurethane blends: influence of modified natural rubbers on properties of the blends

Three different forms of natural rubber: maleated natural rubber (MNR), epoxidized natural rubber (ENR) and natural rubber-graft-poly(methyl methacrylate) (NR-g-PMMA) were prepared. Degree of functional groups in rubber molecules was quantified using the integrated peak areas of ¹H NMR. It was found that the modified rubbers with similar level of functionality had been successfully prepared. Thermoplastic natural rubber (TPNR) based on blending of thermoplastic polyurethane (TPU) and various forms of rubber were then prepared using melt blending method. The properties of the blends were studied and compared together in relation to different types of natural rubbers prepared (i.e., unmodified NR, MNR, ENR and NR-g-PMMA). It was found that the blends with modified NR exhibited superior stiffness, entropy effect and damping factor compared to other blends with unmodified NR. This is attributed to the chemical interaction between the functional groups of modified NR molecules and polar functional groups in TPU molecules which facilitated higher interfacial adhesion between both phases. The chemical interaction was verified by ATR-FTIR and TSSR techniques. It was also found that the MNR/TPU blend showed the highest tensile modulus, mechanical and elastic properties with smallest and finer grain dispersion of co-continuous phase compared to ENR/TPU, NR-g-PMMA/TPU and unmodified NR/TPU blends, respectively. This might be due to higher chemical interactions between MNR and TPU phases. Furthermore, the incorporation of rubber did reduce hardness (i.e., <60 Shore A) with improvement of elasticity of the blends compared with the original TPU (i.e., ~85 Shore A).     

Development of polybutadiene (BR)–polyethylene (LDPE) blend based microcellular soles for low‐temperature applications

Microcellular (MC) soles based on polybutadiene (BR) and low‐density polyethylene (LDPE) blends for low‐temperature applications were developed. A part of BR in BR–LDPE blend was replaced by natural rubber (NR) for property improvement. The BR–NR–LDPE blend‐based MC sole shows good technical properties. Sulphur curing and DCP curing were tried in BR–LDPE and NR–BR–LDPE blends. Study shows that sulphur‐cured MC sheets possess better technical properties than DCP‐cured MC sheets. 90/10 BR–LDPE and 60/30/10 BR–NR–LDPE blend combinations are found to be suitable for low‐temperature applications. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 277–281, 2000     

Effects of zinc borate loading on thermal stability,flammability, crystallization properties of magnesium oxide/(90/10) mLLDPE/(NR/ENR-50) blends

Effects of different zinc borate (ZB) loadings on thermal, flammability and crystallinity properties of blends of 10 % rubber (9/1) natural rubber (NR)/epoxidised natural rubber (ENR)/metallocene linear low density polyethylene/N,N-m-phenylenebismaleimide/MgO were investigated. Fourier transform infrared spectroscopy revealed that –C=O and –OH groups appeared while C–O–C and C=C groups disappeared in all blend samples. ZB increased the activation of HVA-2 by changing the reaction mechanism and increasing the concentration of the –C=O groups in the blends due to the peak at 1,714–1,718 cm^?1. The crystallinity of all blends was increased by ZB loading increase; therefore, it played the heterogeneous nucleation center and maximum crystallinity was observed at 6 phr ZB blend. The thermal stability of NR improved with increase of zinc borate loading and the highest thermal stability was determined for 8 phr ZB blend. Good compatibilization between the two rubbers (NR/ENR-50) was achieved in the presence of ZB, which was revealed by the presence of only one peak for their decomposition. The limiting oxygen index value of mLLDPE was decreased by two rubbers loading increase, while it was increased by ZB loading increase to provide fire barriers to protect flammable materials from thermal damage. It was concluded that ZB has a synergistic effect on the LOI values of flame retardant mLLDPE/rubber containing MgO.     

Compatibility studies on some polymer blend systems by electrical and mechanical techniques

Systematic electrical and mechanical studies were carried out on natural rubber (NR) blended with different types of synthetic rubber such as styrene‐butadiene rubber (SBR), polybutadiene rubber (BR), and ethylene‐propylene‐diene monomer (EPDM) as nonpolar rubbers and nitrile‐butadiene rubber (NBR) and chloroprene rubber (CR) as polar rubbers. The NR/SBR, NR/BR, NR/EPDM, NR/NBR, and NR/CR blends were prepared with different ratios (100/0, 75/25, 50/50, 25/75, and 0/100). The permittivity (ε′) and dielectric loss (ε″) of these blends were measured over a wide range of frequencies (100 Hz–100 kHz) and at room temperature (∼ 27°C). The compatibility results obtained from the dielectric measurements were comparable with those obtained from the calculation of the heat of mixing. These results were confirmed by scanning electron microscopy and showed that NR/SBR and NR/BR blends were compatible while NR/EPDM, NR/NBR, and NR/CR blends were incompatible. To overcome the problem of phase separation (incompatibility) between NR and EPDM, NBR, or CR, a third component such as SBR or poly(vinyl chloride) (PVC) was added as a compatibilizing agent to these blends. The experimental data of dielectric and mechanical measurements showed that the addition of either SBR or PVC could improve the compatibility of such blends to some extent. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 60–71, 2001     

TENSILE PROPERTY OF EPOXIDIZED NATURAL RUBBER/NATURAL RUBBER BLENDS

The tensile strength and elongation at break of epoxidized natural rubber (ENR) blended with natural rubber (NR) was studied. ENR 25, ENR 50, and one grade of natural rubber (SMR L) were used as the elastomers. The composition of ENR was varied from 0% to 100% rubber. The accelerated sulfur vulcanization system was used throughout the investigation. The tensile property of unaged and aged samples was determined by using the Monsanto tensometer (T10) operating at 50 cm/min. Results show that the tensile strength and elongation at break passes through a maximum at 50% ENR for both ENR25/SMR L and ENR50/SMR L blends. This positive deviation from ideality is attributed to the mutual reinforcement of ENR and NR in the blends as a result of strain-induced crystallization. This synergistic effect is more pronounced in the case of ENR 25 due to the higher crystallinity and availability of more double bonds, which is more compatible to NR compared to ENR 50/NR blends. For the aged samples, a drop in the tensile property associated to the breakdown of the polysulfidic cross-link during aging is observed. A systematic study of the effect of sulfur concentration on the percentage retention of tensile property of the ENR blends after aging reveals that percentage retention decreases with increasing sulfur loading, which, in turn, enhances the formation of the polysulfidic cross-link; thus, more breakdown is observed in the rubber vulcanizate.     

Mechanical properties and blend compatibility of natural rubber –chlorosulfonated polyethylene blends

Natural rubber (NR) was blended with chlorosulfonated polyethylene (CSM) with various formulation and blend ratios (NR/CSM: 80/20 –20/80, wt/wt). Rubber blends were prepared by using a two‐roll mill and vulcanized in a compression mold to obtain the 2 mm‐thick sheets. Tensile properties, tear resistance, thermal aging resistance, ozone resistance, and oil resistance were determined according to ASTM. Compatible NR/CSM blends are derived from certain blends containing 20–30% CSM without adding any compatibilizing agent. Tensile and tear strength of NR‐rich blends for certain formulations show positive deviation from the rule of mixture. Thermal aging resistance depends on formulation and blend ratio, while ozone and oil resistance of the blends increase with CSM content. Homogenizing agents used were Stuktol®60NS and Epoxyprene®25. Stuktol®60NS tends to decrease the mechanical properties of the blends and shows no significant effect on blend morphology. Addition of 5–10 phr of epoxidized natural rubber (ENR, Epoxyprene® 25) increases tensile strength, thermal aging resistance, and ozone resistance of the blends. It is found that ENR acts as a compatibilizer of the NR/CSM blends by decreasing both CSM particle size diameter and α transition temperature of CSM. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 127–140, 2006     

Thermoplastic elastomers-based natural rubber and thermoplastic polyurethane blends

Thermoplastic elastomers based on the blends of thermoplastic polyurethane (TPU) and natural rubber were prepared by a simple blend technique. The influence of the two different types of natural rubber (i.e., unmodified natural rubber (NR) and epoxidized natural rubber (ENR)) on properties of the blends was investigated. The main aim of this study was to improve heat resistance and damping properties, and also to prepare the TPU material with low hardness by blending with various amounts of natural rubber. It was found that the TPU/ENR blends exhibited superior modulus, hardness, shear viscosity, stress relaxation behavior and heat-resistant properties compared to the blends with TPU and unmodified NR. This was attributed to higher chemical interaction between the polar functional groups of ENR and TPU by improving the interfacial adhesion. It was also found that the ENR/TPU blends exhibited finer grain morphology than the blends with unmodified NR. Furthermore, lower tension set, damping factor (Tan ??) and hardness, but higher degradation temperature, were observed in natural rubber/TPU blends compared to pure TPU. This proves the formation of TPU material with high heat resistance, low hardness and better damping properties. However, the blends with higher proportion of natural rubber exhibited lower tensile strength and elongation at break.     

SORPTION,DIFFUSION, AND PERMEATION OF CHLORINATED HYDROCARBON VAPORS THROUGH NATURAL RUBBER,EPOXIDIZED NATURAL RUBBER,AND THEIR BLENDS

The study investigates the transport process of various chlorinated hydrocarbons through natural rubber (NR), epoxidized natural rubber (ENR), and their blends. The effect of structure and morphology of the membranes on the transport parameters has been investigated. Sorption coefficient is found to increase and the permeability coefficient shows the reverse trend with increasing epoxy content. As the mol% epoxidation increases, the polymeric network structure becomes more compact, which leads to a decrease in the diffusion coefficient, which ultimately results in a low permeation coefficient. The morphology of NR/ENR blends has been investigated by combining scanning electron microscopy with permeability measurements. The permeation coefficient is found to be minimum for the NR/ENR 70/30 composition; a 50/50 composition shows the maximum. The heterogeneous morphology of 70/30 NR/ENR blend results in the low permeability coefficient, whereas the co-continuous nature of the 50/50 composition accounts for the maximum permeability. Permeability measurements provide the most useful information about the way morphology is changing with composition of the blends and about the composition corresponding to the maximum level of co-continuity of the two phases.     

Blending of NR/BR/EPDM by reactive processing for tire sidewall applications. I. Preparation,cure characteristics and mechanical properties

EPDM incorporated into blends of natural rubber/butadiene rubber (NR/BR) improves ozone resistance. In this work, the inferior mechanical properties of NR/BR/EPDM blends generally obtained by conventional straight mixing are overcome by utilizing a reactive processing technique. The entire amount of curatives, based on a commonly employed accelerator N‐cyclohexyl‐2‐benzothiazole sulfenamide (CBS) and sulfur, is first added into the EPDM phase. After a thermal pretreatment step tuned to the scorch time of the EPDM phase, the modified EPDM is mixed with premasticated NR/BR. The reactive blend vulcanizates show a significant improvement in tensile properties: tensile strength and elongation at break, as compared to those prepared by straight mixing, in both gum and carbon black‐filled blends. The increase of tensile properties in gum and filled reactive blend vulcanizates does suggest that the reactive processing technique leads to more homogeneous blends due to, either a better crosslink distribution, or more homogeneous filler distribution, or both. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:2538–2546, 2007     

Effect of blend ratio on Mooney scorch time of rubber blends

The Mooney scorch times of three rubber blends [epoxidized natural rubber (ENR) 50/SMR L, ENR 50/styrene butadiene rubber (SBR), and Standard Malaysian Rubber SMR L/SBR] were studied in the temperature range of 120–160°C using an automatic Mooney viscometer. N-Cyclohexyl-2-benzothiazyl sulfenamide was used as the accelerator, and the rubber formulation was based on the conventional vulcanization system. Results for the blends investigated indicate that a negative deviation of scorch time from the interpolated value was observed, especially for temperatures lower than 130°C. This observation was attributed to the induction effect of the ENR 50 in the ENR 50/SMR L and ENR 50/SBR blends to produce more activated precursors to crosslinks, thus enhancing interphase crosslinking. To a lesser extent, SMR L also exhibited such an induction effect in the SMR L/SBR blend. At 120°C, maximum induction effect occurred at around a 40% blend ratio of ENR 50 and SMR L in the respective blends. For the filled stock at 140°C, carbon black exhibited less effect on the scorch property of the blends compared to silica. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1301–1305, 1998     

Preparation and characterization of high performance exfoliated montmorillonite/silicone rubber nanocomposites with enhanced mechanical properties

Highly exfoliated and intercalated silicone rubber (SR) nanocomposites based on natural montmorillonite (Cloisite Na⁺) and organically modified montmorillonite (Cloisite 30B and Cloisite 20A) were successfully prepared by melt‐mixing technique. Dispersion of the nanoclays in the rubber nanocomposites was subsequently investigated. As indicated by the X‐ray diffraction (XRD) analysis, intercalation, and exfoliation of the clay particles in the nanocomposites was achieved at less than 8 parts per hundred (phr) rubber by weight, irrespective of the initial interlayer spacing of the nanoclay particles. Both Cloisite Na⁺ and Cloisite 30B were spontaneously transformed into exfoliated microstructures during the vulcanisation stage. Overall, the use of the nanoclays in silicone rubber improved the Young's modulus, tensile strength, and elongation at break by more than 50% as compared with the control rubber. In addition, this work provided a fresh insight into the way intercalated and exfoliated morphologies affect mechanical properties of silicone rubber nanocomposites. It was shown that the exfoliated Cloisite Na⁺ yielded outstanding mechanical properties with low hysteresis at the same loading of the exfoliated Cloisite 30B and intercalated Cloisite 20A organoclays. As expected, the formation of crosslinks affected the mechanical properties of the rubber vulcanizate significantly. POLYM. ENG. SCI., 53:2603–2614, 2013. © 2013 Society of Plastics Engineers     

Adhesion properties of pressure-sensitive adhesives prepared from SMR 10/ENR 25, SMR 10/ENR 50, and ENR 25/ENR 50 blends

The adhesion properties, i.e. viscosity, tack, and peel strength of pressure-sensitive adhesives prepared from natural rubber/epoxidized natural rubber blends were investigated using coumarone-indene resin and toluene as the tackifier and solvent respectively. One grade of natural rubber (SMR 10) and two grades of epoxidized natural rubbers (ENR 25 and ENR 50) were used to prepare the rubber blends with blend ratio ranging from 0 to 100%. Coumarone-indene resin content was fixed at 40 parts per hundred parts of rubber (phr) in the adhesive formulation. The viscosity of adhesive was measured by a HAAKE Rotary Viscometer whereas loop tack and peel strength was determined using a Lloyd Adhesion Tester operating at 30 cm/min. Results show that the viscosity of the adhesive passes through a minimum value at 20% blend ratio. For loop tack and peel strength, it indicates a maximum at 60% blend ratio for SMR 10/ENR 25 and SMR 10/ENR 50 systems. However, for ENR 25/ENR 50 blend, maximum value is observed at 80% blend ratio. SMR 10/ENR 25 blend consistently exhibits the best adhesion property in this study, an observation which is attributed to the optimum compatibility between rubbers and wettability of adhesive on the substrate. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influences of trans‐polyoctylene rubber on the physical properties and phase morphology of natural rubber/acrylonitrile–butadiene rubber blends

The influence of trans‐polyoctylene rubber (TOR) on the mechanical properties, glass‐transition behavior, and phase morphology of natural rubber (NR)/acrylonitrile–butadiene rubber (NBR) blends was investigated. With an increased TOR level, hardness, tensile modulus, and resilience increased, whereas tensile strength and elongation at break tremendously decreased. According to differential scanning calorimetry and dynamic mechanical analysis, there were two distinct glass‐transition temperatures for a 50/50 NR/NBR blend, indicating the strongly incompatible nature of the blend. When the TOR level was increased, the glass transition of NBR was strongly suppressed. NBR droplets of a few micrometers were uniformly dispersed in the continuous NR phases in the NR/NBR blends. When TOR was added to a 50/50 NR/NBR blend, TOR tended to be located in the NR phase and in some cases was positioned at the interfaces between the NBR and NR phases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 125–134, 2002     

Characterization of epoxidized natural rubber/ethylene vinyl acetate (ENR‐50/EVA) blend: Effect of blend ratio

Epoxidized natural rubber/Ethylene vinyl acetate copolymer (ENR‐50/EVA) blends with different ratios were prepared by using a Haake internal mixer. The effect of the blend ratio on the processing, tensile properties (such as tensile strength, elongation at break, Young's modulus and stress–strain behavior), morphology, dynamic mechanical properties, and thermal properties has been investigated. The tensile properties increase with the increase of EVA content, whereas the stabilization torque increases with the increase of ENR‐50 content in the blend. In 40:60 and 50:50 blend of ENR‐50/EVA, both the phases exist as continuous phases, producing a co‐continuous morphology. At these blend ratio, the drastic change in properties were noted, indicating that the phase inversion occurs. The results on dynamic mechanical properties revealed that the blends are compatible. Blending of ENR‐50 and EVA lead to the improvement in thermal stability and 50:50 blend ratios is the most stable blend. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1504–1515, 2006     

Toughness enhancement of poly(lactic acid) by melt blending with natural rubber

Rubber toughened poly(lactic acid) (PLA) was prepared by blending with natural rubber (NR)‐based polymers. The blends contained 10 wt % of rubber and melt blended with a twin screw extruder. Enhancement of impact strength of PLA was primarily concernced. This study was focused on the effect of rubber polarity, rubber viscosity and molecular weight on mechanical properties of the blends. Three types of rubbers were used: NR, epoxidized natural rubber (ENR25 and ENR50), and natural rubber grafted with poly(methyl methacrylate) (NR‐g‐PMMA). Effect of viscosity and molecular weight of NR, rubber mastication with a two‐roll mill was investigated. It was found that all blends showed higher impact strength than PLA and NR became the best toughening agent. Viscosity and molecular weight of NR decreased with increasing number of mastication. Impact strength of PLA/NR blends increased after applying NR mastication due to appropriate particle size. DMTA and DSC characterization were determined as well. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011