ICAR ATRP of methyl methacrylate catalyzed by FeCl3·6H2O/succinic acid

In this work, methyl methacrylate (MMA) was polymerized by initiator for continuous activator regeneration (ICAR) atom transfer radical polymerization (ATRP) method to obtain low molecular weight living polymers. The ATRP initiator was ethyl 2‐bromoisobutyrate, the catalyst ligand complex system was FeCl₃·6H₂O/succinic acid, and the conventional radical initiator 2,2′‐azobisisobutyronitrile was used as a thermal radical initiator. Polymers with controlled molecular weight were obtained with ppm level of Fe catalyst complex at 90°C in N,N‐dimethylformamide. The polymer was characterized by nuclear magnetic resonance (NMR). The molecular weight and molecular weight distribution of the obtained poly (methyl methacrylate) were measured by gel permeation chromatography method. The kinetics results indicated that ICAR ATRP of MMA was a “living”/controlled polymerization, corresponding to a linear increase of molecular weights with the increasing of monomer conversion and a relatively narrow polydispersities index. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Using hydroxypropyl‐β‐cyclodextrin for the preparation of hydrophobic poly(ketoethyl methacrylate) in aqueous medium

This work was committed to the polymerization of hydrophobic ketoethyl methacrylate monomer in aqueous medium in the presence of cyclodextrin, instead of polymerizing the monomer in toxic and volatile organic solvents. For this purpose, a new ketoethyl methacrylate monomer, p‐methylphenacylmethacrylate (MPMA), was synthesized from the reaction of p‐methylphenacylbromide with sodium methacrylate in the presence of triethylbenzylammonium chloride. The monomer was identified with FTIR, ¹H and ¹³C‐NMR spectroscopies. Hydroxypropyl‐β‐cyclodextrin (HPCD) was used to form a water‐soluble host/guest inclusion complex (MPMA/HPCD) with the hydrophobic monomer. The complex was identified with FTIR and NMR techniques and polymerized in aqueous medium using potassium persulfate as initiator. During polymerization the resulting hydrophobic methacrylate polymer precipitated out with a majority of HPCD left in solution and a minority of HPCD bonded on the resulting polymer. The thus‐prepared polymer exhibited little difference from the counterparts obtained in organic solvent in number average molecular weight (M_n), polydispersity (M_w/M_n) and yield. The investigation provides a novel strategy for preparing hydrophobic ketoethyl methacrylate polymer in aqueous medium by using a monomer/HPCD inclusion complex. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Methyl acrylate/1‐octene copolymers: Lewis acid‐mediated polymerization

Copolymerization of methyl acrylate (MA) with 1‐octene (1‐Oct) was conducted in the presence of free radical initiator, 2,2′‐azobis(2‐methylpropionitrile) (AIBN) using heterogeneous Lewis acid, acidic alumina. The polymers obtained were transparent and highly viscous liquids. The copolymer composition calculated from ¹H NMR showed alkene incorporation in the range of 10–61%. The monomodal nature of chromatographic curves corresponding to the molecular weight distribution in gel permeation chromatography (GPC) further confirmed that the polymers obtained are true copolymers. The number–average molecular weights (M_n) of the copolymers were in the range of 1.1 × 10⁴–1.6 × 10⁴ with polydispersity index of 1.75–2.29. The effects of varying the acidic alumina amount, time of polymerization, and monomer infeed on the incorporation of 1‐Oct in the polymer chain were studied. Increased 1‐Oct infeed led to its higher inclusion in the copolymer chain as elucidated by NMR. DEPT‐135 NMR spectral analysis was used to explicate the nature of arrangement of monomer sequences in the copolymer chain. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Zinc‐based catalyst for the ring‐opening polymerization of cyclic esters

A zinc‐based catalyst zinc bis[bis(trimethylsilyl)amide] was used for the polymerization of cyclic esters including L ‐lactide (L ‐LA) and 2‐methyl‐2‐carboxyl‐propylene carbonate (MBC). The polymerization of L ‐lactide in THF could be carried out successfully under mild conditions in very short time by using the zinc catalyst and alcohols as the initiators. Kinetic study in solution polymerization prooved the polymerization has high monomer conversion degree close to 100% and the molecular weight of the resulting polyester has linear increase with the increase of [M]₀ /[I] (molar ratio of monomer to initiator). Sequential polymerization of L ‐LA and MBC in THF also showed high MBC conversion of 94% with a narrow molecualr weight maintained, indicating a living nature of this polymerization. The zinc catalyst system has also been used for the L ‐LA bulk polymerization with a high monomer conversion. ¹³C NMR indicated the polymer possesses high regioregularity and the minor regioirregular component was owing to the D ‐LA in the monomer inserted into the polymer mainchain during the transesterifcation. Interaction between monomer and zinc catalyst has been found to be a key factor to sustain a homogenous solution during the initiating procedure. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

A new atom transfer radical polymerization initiator based on phenolphthalein for the synthesis of bis‐allyloxy functionalized polystyrene macromonomers

A new atom transfer radical polymerization (ATRP) initiator, namely 2‐(1,1‐bis(4‐(allyloxy)phenyl)‐3‐oxoisoindolin‐2‐yl)ethyl 2‐bromo‐2‐methylpropanoate, was synthesized starting from phenolphthalein, a commercially available and an inexpensive chemical. Well‐ defined bis‐allyloxy functionalized polystyrene macromonomers (M_n,GPC 4800–11 700 g mol^?1) with controlled molecular weight and narrow molecular weight distribution (1.05–1.09) were synthesized using ATRP by varying the monomer to initiator feed ratio. The presence of allyloxy functionality on polystyrene was confirmed by Fourier transform infrared and ¹H NMR spectroscopy. A kinetic study of polymerization revealed pseudo‐first‐order kinetics with respect to monomer consumption. Initiator efficiency was found to be in the range 0.80–0.95. Matrix‐assisted laser desorption ionization time of flight spectra showed a narrow molecular weight distribution with control over the molecular weight. The reactivity of the allyloxy groups on polystyrene was successfully demonstrated by quantitative photochemical thiol‐ene click reaction with benzyl mercaptan as the model thiol reagent. Furthermore, the thiol‐ene click reaction was exploited to introduce other reactive functional groups such as hydroxyl and carboxyl by reaction of α,α′‐bis‐allyloxy functionalized polystyrene with 2‐mercaptoethanol and 3‐mercaptopropionic acid, respectively. © 2014 Society of Chemical Industry     

A novel strategy to branched polyacrylonitrile via one‐pot RAFT copolymerization of acrylonitrile and an asymmetrical divinyl monomer

Branched polyacrylonitriles were prepared via the one‐pot radical copolymerization of acrylonitirle and an asymmetric divinyl monomer (allyl methacrylate) that possesses both a higher reactive methacrylate and a lower reactive allyl. RAFT technique was used to keep a low‐propagation chain concentration via a fast reversible chain transfer euilibration and thus the cross‐linking was prevented until a high level of monomer conversions. This novel strategy was demonstrated to engenerate a branched architecture with abundant pendant functional vinyl and nitrile groups, and controlled molecular weight as a behavior of controlled/living radical polymerization characteristics. The effect of the various experimental parameters, including temperature, brancher to monomer molar ratio, and chain transfer agent to initiator molar ratio, on the control of moleculer dimension (molecular weight and polydispersity indices) and the degree of branching were investigated in detail. Moreover, ¹H NMR and gel permeation chromatography confirm the branched architecture of the resultant polymer. The intrinsic viscosity of the copolymer is also lower than the linear counterpart.© 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of AB‐type copolymers poly(L‐lactide)‐block‐poly(methyl methacrylate) via a convenient route combining ROP and ATRP from a dual initiator

Diblock copolymers of poly(L ‐lactide)‐block‐poly(methyl methacrylate) (PLLA‐b‐PMMA) were synthesized through a sequential two‐step strategy, which combines ring‐opening polymerization (ROP) and atom transfer radical polymerization (ATRP), using a bifunctional initiator, 2,2,2‐trichloroethanol. The trichloro‐terminated poly(L ‐lactide) (PLLA‐Cl) with high molecular weight (M_n,GPC = 1–12 × 10⁴ g/mol) was presynthesized through bulk ROP of L ‐lactide (L ‐LA), initiated by the hydroxyl group of the double‐headed initiator, with tin(II) octoate (Sn(Oct)₂) as catalyst. The second segment of the block copolymer was synthesized by the ATRP of methyl methacrylate (MMA), with PLLA‐Cl as macroinitiator and CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as catalyst, and dimethyl sulfoxide (DMSO) was chosen as reaction medium due to the poor solubility of the macroinitiator in conventional solvents at the reaction temperature. The trichloroethoxyl terminal group of the macroinitiator was confirmed by Fourier transform infrared spectroscopy (FTIR) and ¹H‐NMR spectroscopy. The comprehensive results from GPC, FTIR, ¹H‐NMR analysis indicate that diblock copolymers PLLA‐b‐PMMA (M_n,GPC = 5–13 × 10⁴ g/mol) with desired molecular composition were obtained by changing the molar ratio of monomer/initiator. DSC, XRD, and TG analyses establish that the crystallization of copolymers is inhibited with the introduction of PMMA segment, which will be beneficial to ameliorating the brittleness, and furthermore, to improving the thermal performance. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Practical Continuous‐Flow Controlled/Living Anionic Polymerization

A continuous‐flow reaction system was developed, allowing flow conditions of the entire system to be maintained at a predetermined constant level, which is one of the most significant factors for successful industrial application. Controlled/living anionic polymerization was selected as a model reaction since the characteristics of its polymer products, molecular weights, and molecular weight distributions are highly susceptible to changes in the relative flow rates of a monomer and initiator solutions. In flow microreactors, controlled/living anionic polymerization of styrene in tetrahydrofuran (THF)/hexane initiated by THF‐diluted n‐butyllithium (n‐BuLi) was examined. Poly(styrenes) of larger molecule sizes such as Mn > 15 000 were successfully synthesized. After continuous operation for four hours, ca. 0.5 kg of the polymer was readily produced with narrow molecular weight distribution, demonstrating the applicability of this continuous‐flow system for controlled/living anionic polymerization on considerably large scale with a view to its industrial usage in the future.     

Fe‐mediated ICAR ATRP of styrene and acrylonitrile in polyethylene glycol

In this contribution, random copolymers of p(styrene‐co‐acrylonitrile) via initiators for continuous activator regeneration (ICAR) in atom transfer radical polymerization (ATRP) (ICAR ATRP) of styrene and acrylonitrile (SAN) were synthesized at 90°C in low molecular weight polyethylene glycol (PEG‐400) using CCl₄ as initiator, FeCl₃·6H₂O as catalyst, succinic acid as ligand and thermal radical initiator azobisisobutyronitrile (AIBN) as thermal free radical initiator. In this system, well‐defined copolymer of SAN was achieved. The kinetics results showed that the copolymerization rate obeyed first‐order kinetics model with respect to the monomer concentration, and a linear increase of the molecular weights with the increasing of monomer conversion with narrow molecular weight distribution was observed in the range of 1.1–1.5. The conversion decreased with increasing the amount of FeCl₃·6H₂O and increased with increasing the molar ratio of [St]₀/[AN]₀/[CCl₄]₀ and temperature. AIBN has a profound effect on the polymerization. The activation energy was 55.67 kJ mol^?1. The living character of copolymerization was confirmed by chain extension experiment. The resultant random copolymer was characterized by ¹H‐NMR and GPC. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40135.     

Copolymerization of styrene with an α‐olefin via atom transfer radical polymerization

This investigation reports the preparation of styrene–α‐olefinic random copolymers, using 1‐octene as an α‐olefin, via atom transfer radical polymerization. Atom transfer radical copolymerization of styrene with 1‐octene was successfully carried out using phenylethyl bromide as initiator and CuBr as catalyst in combination with N, N, N′, N″, N″‐pentamethyldiethylenetriamine as ligand. The copolymers had controlled molecular weight, narrow dispersity and well‐defined end groups with significant 1‐octene incorporation in the polymer. Incorporation of 1‐octene in the copolymers was confirmed using ¹H NMR and matrix‐assisted laser desorption ionization time‐of‐flight mass spectroscopy. An increase in 1‐octene content in the monomer feed led to an increase in the level of incorporation of the α‐olefin in the copolymer. An increase in the concentration of 1‐octene led to a decrease in the rate of polymerization and an increase in dispersity. The glass transition temperature of the copolymer gradually decreased as the incorporation of 1‐octene increased. Copyright © 2011 Society of Chemical Industry     

Synthesis of hydroxyethylcellulose‐graft‐poly(N,N‐dimethylacrylamide) copolymer by ATRP and as dynamic coating in capillary electrophoresis

Hydroxyethylcellulose‐graft‐poly (N, N‐dimethylacrylamide) was synthesized by successive atom transfer radical polymerization (ATRP) of N,N‐dimethylacrylamide (DMA) monomer using HEC‐Br as initiator, CuBr and 5,5,7,12,12,14‐hexamethyl‐1,4,8,11‐tetraazamacrocyclotetradecane (Me₆[14]aneN₄) as catalyst and ligand, with molar ratio DMA: HEC‐Br (C? Br): CuBr: Me₆[14]aneN₄ = 100 : 1 : 1 : 3. HEC–Br macroinitiator was synthesized by esterification of HEC with 2‐bromoisobutyryl bromide. GPC and ¹H NMR studies show that the molecular weight of the resulting PDMA increased linearly with the conversion. Within 6 h, the polymerization can reach almost 60% of conversion. The copolymer is applied for the separation of basic proteins in capillary electrophoresis. The results show that this medium has a powerful capability in resisting basic proteins adsorption because the polymer forms noncovalent coating in silica capillaries. With a broad range of pH 2–7, proteins were separated with sufficient efficiencies above 200,000 plates/m. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Low‐molecular‐weight polytetrafluoroethylene bearing thermally stable perfluoroalkyl end‐groups prepared in supercritical carbon dioxide

Low‐molecular‐weight (M_n) polytetrafluoroethylene (PTFE) homopolymers were successfully prepared using a perfluorodiacyl initiator, bis(perfluoro‐2‐n‐propoxypropionyl) peroxide, in supercritical carbon dioxide. Solid‐state ¹⁹F NMR and Fourier transform infrared spectral analyses show that perfluoroalkyl end‐groups are present in the resultant PTFEs. Thermogravimetric analysis suggests all polymers with various M_n have outstanding thermal stability. Differential scanning calorimetry measurements indicate that both melting and crystallization transitions of PTFE shift to lower temperatures when M_n decreases, because shorter polymer chains can move more easily at lower temperatures. Investigation of polymerization kinetics suggests that the rate law for the polymerization has kinetic orders of 0.5 and 1.0 with respect to initiator and monomer concentrations, indicating that termination occurs through coupling of propagating chains. Melt fusion crystallinity of as‐polymerized PTFE can be as high as 86%, and the polymerization rate does not seem to be obviously affected by the total interphase area of the polymer phase, implying polymerization mainly occurs in the carbon dioxide‐rich fluid phase; meanwhile, the low viscosity and high diffusivity of supercritical carbon dioxide mean that propagating chains have more opportunities to meet, thus yielding low‐M_n PTFEs. Copyright © 2012 Society of Chemical Industry     

Indole‐based polymer and its silver nanocomposite as advanced antibacterial agents: synthetic path,kinetics of polymerization and applications

Atom transfer radical polymerization of 1‐allylindole‐3‐carbaldehyde (AIC) was studied by employing 2‐bromoisobutyryl bromide as initiator in toluene. It led to controlled radical polymerization of AIC, with an increase of molecular weight along with the conversion of the monomer, and a relatively narrow molar mass distribution was obtained, as determined by gel permeation chromatography. The living nature of poly(1‐allylindole‐3‐carbaldehyde) (PAIC) was confirmed by the chain extension polymerization whereas ¹H NMR analysis showed that the major population of PAIC retained the chain‐end functional group. PAIC and its silver nanocomposite were found to be biologically active against some tested bacterial pathogens. Minimum inhibitory concentration tests revealed that PAIC exhibited antibacterial activity against Staphylococcus aureus, Proteus mirabilis and Klebsiella pneumonae whereas PAIC/Ag nanocomposite showed antibacterial activity against Enterococcus faecalis and K. pneumonae. © 2012 Society of Chemical Industry     

Synthesis of 5‐vinyl‐m‐ phenylene‐m′‐phenylene‐32‐ crown‐10 and its radical polymerization behavior

Synthesis of a vinyl monomer, containing a 32‐membered crown ether unit (VCE) as a pendant group, was achieved by using tetra(ethylene glycol) dichloride, resorcinol, and 3,5‐dihydroxyacetophenone as starting materials. The product was identified by means of FTIR and ¹H‐NMR. It was found that this monomer readily polymerizes by the conventional radical initiator 2,2′‐ azobisisobutyronitrile (AIBN) to afford a polymer whose number‐average molecular weight is 36 kg/mol; however, the final conversion of the polymer was < 80%. The results of the copolymerization of VCE with styrene (ST) or acrylonitrile (AN) are also discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2372–2379, 2002     

Ultrasonically initiated emulsion polymerization of n‐butyl acrylate

Ultrasonically initiated emulsion polymerization of n‐butyl acrylate (BA) without added initiator has been studied. The experimental results show that high conversion of BA can be reached in a short time by employing an ultrasonic irradiation technique with a high purge rate of N₂. The viscosity average molecular weight of poly(n‐butyl acrylate) (PBA) obtained reaches 5.24 × 10⁶ g mol^?1. The ultrasonically initiated emulsion polymerization is dynamic and complicated, with polymerization of monomer and degradation of polymer occurring simultaneously. An increase in ultrasound intensity leads to an increase in polymerization rate in the range of cavitation threshold and cavitation peak values. Lower monomer concentration favours enhancement of the polymerization rate. ¹H NMR, ¹³C NMR and FTIR spectroscopies reveal that there are some branches and slight crosslinking, and also carboxyl groups in PBA. Ultrasonically initiated emulsion polymerization offers a new route for the preparation of nanosized latex particles; the particle size of PBA prepared is around 50–200 nm as measured by transmission electron microscopy. © 2001 Society of Chemical Industry     

Visible‐light‐induced controlled/living radical polymerization of styrene with a phenyl seleno group at one terminal chain end: 1‐(Phenylseleno)ethyl benzene as a photoiniferter

The photopolymerization of styrene with a well‐defined molecular architecture and a low polydispersity index and with methyl and phenylseleno (? SePh) groups at α‐ and ω‐chain ends, respectively, was performed via a controlled/living radical polymerization with a new initiating system, 1‐(phenylseleno)ethyl benzene/tert‐butyl diphenyl (phenylseleno) silane, through the absorption of visible light at room temperature. A novel initiating living radical polymerization was examined. The yield and number‐average molecular weight (M_n) of the resulting polymer increased with the reaction time. Furthermore, a linear relationship was found in a plot of M_n versus the polymer yield. These results indicated that this polymerization proceeded through a living radical mechanism. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 348–355, 2004     

Reverse iodine transfer polymerization of vinyl acetate and vinyl benzoate: synthesis and characterization of homo‐ and copolymers

Homo‐ and copolymers of vinyl esters including vinyl acetate (VAc) and vinyl benzoate (VBz) were synthesized via the reverse iodine transfer radical polymerization technique. Polymerization was carried out in the presence of iodine as the in situ generator of the transfer agent and 2,2′‐azobis(isobutyronitrile) as the initiator at 70 °C. Reverse iodine transfer radical homopolymerization of VAc and VBz led to conversions of 76 and 57%, number‐average molecular weights of 8266 and 9814 g mol^?1 and molecular weight distributions of 1.58 and 1.49, respectively. The microstructure of the synthesized polymers was investigated in detail using gel permeation chromatography, ¹H NMR, ¹³C NMR and distortionless enhancement of polarization transfer (135° decoupler pulse) techniques. Relatively narrow molecular weight distribution and controlled and predictable trend of molecular weight versus conversion were observed for the synthesized polymers, showing that reverse iodine transfer radical homo‐ and copolymerization of VAc and VBz proceeded with controlled characteristics. Results of molecular weight and its distribution along with the ¹H NMR spectra recorded for homo‐ and copolymers indicated that side reactions can occur during the course of polymerization with a significant contribution when VAc, even in a small amount, was present in the reaction mixture. This can result in polymer chains with aldehyde dead end and broadening of the molecular weight distribution. © 2015 Society of Chemical Industry     

Synthesis and reactivity of functionalized alkoxyamine initiators for nitroxide‐mediated radical polymerization of styrene

The synthesis and examination of different functionalized (2,2,6,6‐tetramethyl‐1‐piperidinyloxy free radical) TEMPO‐containing alkoxyamine initiators for nitroxide‐mediated radical polymerization of styrene are reported. Initiators with ester and carbonate functional groups were synthesized by a low‐temperature radical‐abstraction reaction of the functionalized ethylbenzene in the presence of TEMPO to introduce the functional groups onto the initiating chain‐end of polystyrene. An initiator with two alkoxyamine groups symmetrically located at each end of a carbonate bond was also synthesized and used for nitroxide‐mediated styrene polymerization. Styrene polymerization using these initiators followed first‐order kinetics up to approximately 60 min at 140 °C or 30% monomer conversion. Alkoxyamines bearing an acetoxy or tert‐butylcarbonate group at the p‐position of 1‐(2,2,6,6‐tetramethyl‐1‐piperidinyloxy)ethylbenzene behave in a similar way to the unfunctionalized initiator. With an initiator containing two alkoxyamine groups, the resulting polymer molecular weight was twice that of the polymer obtained from initiators with only one alkoxyamine group, as expected from propagation from both chain‐ends. Upon hydrolysis of the carbonate bond, it was revealed that equivalent polymer chain growth occurred from each alkoxyamine site in the difunctional initiator. Copyright © 2003 Society of Chemical Industry     

Emulsifier‐free emulsion polymerization of styrene

Polystyrene latex particles in an emulsifier‐free emulsion were prepared by purified styrene (St) as monomer and 2,2′‐azobis (2‐amidino propane) dihydrochloride (ABA, 2HCl) as initiator. The optimized condition of polymerization of styrene was obtained by using the various parameters such as different amounts of monomer (0.009, 0.051, and 0.071 mol styrene/mol Water), different amounts of initiator (6.02, 4.62, 2.41, and 1.00 weight percent of initiator relative to styrene), and pH (range 1–7). Quantitative and qualitative analyses of prepared polymer were performed by Scanning Electron Microscopy (SEM), Differential Scanning Calorimetry (DSC), Gel Permeation Chromatography (GPC), and ¹H‐NMR and FT‐IR spectroscopy, that were used, respectively, to show the morphology of particles, the glass transition temperature (T_g), the average molecular weight, and the structure of the prepared polymer. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1898–1904, 2004     

Ring‐opening polymerization of trimethylenecarbonate and its copolymerization with ϵ‐caprolactone by lanthanide (II) aryloxide complexes

Lanthanide metal (II) 2,6‐di‐tert‐butylphenoxide complexes (ArO)₂Ln(THF)₃ (Ln = Sm 1 , Yb 2 ) alone have been developed to catalyze the ring‐opening polymerization of trimethylenecarbonate (TMC) and random copolymerization of TMC and ε‐caprolactone (ε‐CL) for the first time. The influence of reaction conditions, such as initiator, initiator concentration, polymerization temperature, and polymerization time, on monomer conversion, molecular weight, and molecular weight distribution of the resulting PTMC was investigated. It was found that the divalent complex 1 showed higher activity for the polymerization of TMC than complex 2 . The random structure and thermal behavior of the copolymers P(TMC‐co‐CL) have been characterized by ¹H NMR, ¹³C NMR, GPC, and DSC analysis. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007