Effective enhancement of anticorrosive properties of polystyrene by polystyrene–clay nanocomposite materials

A series of polymer–clay nanocomposite (PCN) materials consisting of polystyrene (PS) and layered montmorillonite (MMT) clay was prepared by effectively dispersing the inorganic nanolayers of MMT clay in the organic PS matrix via in situ thermal polymerization. Organic styrene monomers were first intercalated into the interlayer regions of organophilic clay hosts, followed by a typical free radical polymerization with BPO as the initiator. The as‐synthesized PCN materials were characterized by infrared spectroscopy (IR), wide‐angle powder X‐ray diffraction (XRD) and transmission electron microscopy (TEM). PCN coatings with low clay loading (1 wt %) on cold‐rolled steel (CRS) were found to be superior in anticorrosion to those of bulk PS, based on a series of electrochemical measurements of corrosion potential, polarization resistance and corrosion current in a 5 wt % aqueous NaCl electrolyte. The molecular weights of PS extracted from PCN materials and bulk PS were determined by gel permeation chromatography (GPC) with tetrahydrofuran (THF) as the eluent. The effects of material composition on molecular barrier and thermal stability of PS and PCN materials, in the form of both free‐standing films and fine powders, were also studied by molecular permeability analysis, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1970–1976, 2004     

Effect of organoclay on the thermal stability,mechanical strength,and surface wettability of injection‐molded ABS–clay nanocomposite materials prepared by melt intercalation

In this article, a series of polymer–clay nanocomposite (PCN) materials consisted of commercial thermoplastic ABS matrix and dispersing inorganic organoclay platelets were successfully prepared by melt intercalation through the twin‐roller mixer. The as‐prepared materials in the form of pellet were then shaped by injection‐molding machine and the as‐molded specimens were subsequently examined by chemical characterizations, through Fourier transformation infrared (FTIR) spectroscopy, powder X‐ray diffraction (XRD), and transmission electron microscopy (TEM). Effect of the organoclay on thermal stability, mechanical strength, and surface wettability of PCN materials, in both the form of standard dumbbell shape and pellet, was studied using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), tensile test, hardness test, and contact‐angle measurements, respectively. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99; 1576–1582, 2006     

Synthesis and dielectric properties of polystyrene‐clay nanocomposite materials

Polystyrene‐clay nanocomposite (PsCN) materials were synthesized and their properties of crystallinity, thermal behavior, and dielectric characteristics were investigated. A polymerizable cationic surfactant, [2‐(dimethylamino)ethyl]triphenylphonium bromide, was used for the intercalation of montmorillonite (MMT). The organophilic MMT was prepared by Na⁺‐exchanged MMT and ammonium cations of a cationic surfactant in an aqueous medium. Organophilic styrene monomers were intercalated into the interlayer regions of organophilic clay hosts followed by a free‐radical polymerization. Exfoliation to 2 wt % MMT in the polystyrene (PS) matrix was achieved as revealed by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Thermal properties by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were also studied. The dielectric properties of PsCNs in the form of film with clay loading from 1.0 to 5.0 wt % were measured under frequencies of 100 Hz–1 MHz at 25–70°C. A decreased dielectric constant and low dielectric loss were observed for PsCN materials. The dielectric response at low frequency that originated from dipole orientation was suppressed due to the intercalation of clay materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1368–1373, 2004     

Studies on heterogeneous nucleation effect of dispersing intercalated montmorillonite clay platelets in polyaniline matrix

In this article, a series of nanocomposite materials that consisted of emeraldine base (EB) of polyaniline (PANI) and montmorillonite (MMT) clay were prepared by effectively dispersing the inorganic MMT clay platelets into organic PANI matrix via in situ chemically oxidative polymerization. Organic aniline monomers were first intercalated into the interlayer regions of organophilic clay hosts and followed by an one‐step oxidative polymerization with ammonium persulfate as oxidant. The as‐synthesized PANI‐clay nanocomposite (PCN) materials were characterized by Fourier‐Transformation infrared spectroscopy and transmission electron microscopy. It should be noted that the EB of PANI in the presence of dispersed intercalated MMT clay platelets was found to display an observable enhancement in polymer crystallinity as compared with that of neat PANI based on series of investigations of wide‐angle powder X‐ray diffraction patterns and differential scanning calorimetric studies. This remarkable increase of polymer crystallinity might be resulted from the effective heterogeneous nucleation effect of dispersed clay platelets existed in PCN materials. The surface morphology study of PCN materials was further evaluated by polarizing optical microscopy, scanning electron microscopy, and atomic force microscopy. POLYM. COMPOS., 31:2049–2056, 2010. © 2010 Society of Plastics Engineers     

Polystyrene–organoclay nanocomposites prepared by melt intercalation,in situ,and masterbatch methods

In this study, polystyrene (PS)/montmorillonite nanocomposites were prepared by melt intercalation, in situ polymerization, and masterbatch methods. In the masterbatch method, as the first step, a high clay content composite of PS–organoclay (masterbatch) was prepared by in situ polymerization, and then the prepared masterbatch was diluted to desired compositions with commercial PS in a twin‐screw extruder. The structure and mechanical properties of the nanocomposites were examined. X‐ray diffraction (XRD) analysis showed that the d‐spacing of the in situ formed nanocomposites increased from 32.9 Å for the organoclay powder to 36.3 and 36.8 Å respectively in nanocomposites containing 0.73 and 1.6 wt% organoclay, indicating intercalation. However, the d‐spacing of the other prepared materials remained nearly unchanged when compared with pure organoclay powder. Thus, at these low clay contents, in situ formed nanocomposites showed the best improvement in mechanical properties including tensile, impact strength, and Young's modulus. In situ polymerization method did not prove to be efficient at high clay loadings in terms of intercalation and mechanical properties. At high clay loadings, the effects of the three methods in promoting mechanical properties were not significantly different from each other. POLYM. COMPOS., 27:249–255, 2006. © 2006 Society of Plastics Engineers     

Enhanced corrosion protection coatings prepared from soluble electronically conductive polypyrrole‐clay nanocomposite materials

A series of electronically conductive nanocomposite materials that consisted of soluble polypyrrole (PPY) and layered montmorillonite (MMT) clay platelets were prepared by effectively dispersing the inorganic nanolayers of MMT clay in organic PPY matrix via an in situ oxidative polymerization with dodecylbenzene sulfonic acid (DBSA) as dopant. Organic pyrrole monomers were first intercalated into the interlayer regions of organophilic clay hosts and followed by a one‐step oxidative polymerization. The as‐synthesized electronically conductive polypyrrole–clay nanocomposite (PCN) materials were then characterized by Fourier transformation infrared (FTIR) spectroscopy, wide‐angle powder X‐ray diffraction (XRD), and transmission electron microscopy (TEM). PCNs in the form of coatings with low clay loading (e.g., 1.0 wt %) on cold‐rolled steel (CRS) were found to exhibit much better in corrosion protection over those of pristine PPY based on a series of electrochemical measurements including corrosion potential, polarization resistance, and corrosion current in 5 wt % aqueous NaCl electrolyte. Effects of the material composition on the thermal stability, optical properties, and electrical conductivity of pristine PPY along with PCN materials, in the form of fine powder, powder‐pressed pellet, and solution, were also studied by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), UV‐visible absorption spectra, and four‐point probe technique, respectively. The viscosity of PPY existed in PCN materials and pristine PPY were determined by viscometric analysis with m‐cresol as solvent. The heterogeneous nucleating effect of MMT clay platelets in PPY matrix was studied by wide‐angle powder XRD. The corresponding morphological images of the nucleating behavior of clay platelets in PPY matrix were investigated by scanning electron microscopy (SEM). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3264–3272, 2003     

New aramid‐based nanocomposites: Synthesis and characterization

New type of nanocomposites containing various proportions of montmorillonite in aromatic polyamide was prepared via solution intercalation method. Aramid chains were synthesized by reacting 4,4′‐oxydianiline with isophthaloyl chloride in N,N′‐dimethyl acetamide. Dodecylamine was used as swelling agent to change the hydrophilic nature of montmorillonite into organophilic. Appropriate amounts of organoclay were mixed in the polymer solution using high‐speed mixer for complete dispersion of the clay. Thin films cast from these materials after evaporating the solvent were characterized by XRD, TEM, mechanical, thermal, and water absorption measurements. The structure and morphology of the nanocomposites determined by XRD and TEM revealed the formation of exfoliated and intercalated clay platelets in the aramid matrix. Mechanical data indicated improvement in the tensile strength and modulus of the nanocomposites with clay loading up to 6 wt%. The glass transition temperature increased up to 12 wt% clay content and thermal stability amplified with increasing clay loading. The water absorption reduced gradually as a function of organoclay and approached to zero with 20 wt% organoclay in the aramid. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Enhancement of corrosion protection effect of poly(styrene‐co‐acrylonitrile) by the incorporation of nanolayers of montmorillonite clay into copolymer matrix

A series of polymer–clay nanocomposite (PCN) materials that consisted of poly(styrene‐co‐acrylonitrile) (PSAN) and layered montmorillonite (MMT) clay were successfully prepared by effectively dispersing the inorganic nanolayers of MMT clay into the organic PSAN matrix by a conventional in situ thermal polymerization. First of all, organic styrene and AN monomers at a specific feeding ratio were simultaneously intercalated into the interlayer regions of organophilic clay hosts and followed by a typical free‐radical polymerization with benzyl peroxide as initiator. The as‐synthesized PCN materials were subsequently characterized by FTIR spectroscopy, wide‐angle powder X‐ray diffraction, and transmission electron microscopy. The as‐prepared PCN materials, in the form of coatings, incorporated with low clay loading (e.g., 1 wt %) on cold‐rolled steel, were found to be much superior in corrosion protection over those of bulk PSAN based on a series of standard electrochemical measurements of corrosion potential, polarization resistance, and corrosion current in 5 wt % aqueous NaCl electrolyte. Molecular weights of PSAN extracted from PCN materials and bulk PSAN were determined by gel permeation chromatography with THF as eluant. Effects of the material composition on the molecular barrier and thermal stability of PSAN along with PCN materials, in the form of both membrane and fine powder, were also studied by molecular permeability analysis, differential scanning calorimetry, and thermogravimetric analysis, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2269–2277, 2004     

Effect of clay content and clay/surfactant on the mechanical, thermal and barrier properties of polystyrene/organoclay nanocomposites

In the present paper, three ammonium salts namely, tetraethylammonium bromide (TEAB), tetrabutylammonium bromide (TBAB), and cetyltrimethylammonium bromide (CTAB) were employed to prepare organoclay by cation exchange process. Polystyrene (PS) /clay nanocomposites were prepared by melt blending using commercial nanoclay and organoclays prepared using above mentioned salts. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analysis indicated that the modified clays were intercalated and/or exfoliated into the polystyrene matrix to a higher extent than the commercial nanoclay. Further, amongst the modified organoclays, TBAB modified clay showed maximum intercalation of clay layers and also exfoliation to some extent into the polystyrene matrix. TEM micrograph exhibited that TBAB modified clay had the best nanoscale dispersion with clay platelet thickness of ∼6–7 nm only. The mechanical properties of the nanocomposites such as tensile, flexural and izod impact strength were measured and analyzed in relation to their morphology. We observed a significant improvement in the mechanical properties of polystyrene/clay nanocomposites prepared with modified clays as compared to commercial organoclay, which followed the order as; PS/TBAB system > PS/CTAB system > PS/TEAB system. Thermogravimetric analysis (TGA) demonstrated that T₁₀, T₅₀ and Tmax were more in case of polystyrene nanocomposites prepared using modified organoclays than nanoclay [nanolin DK4] and maximum being in the case of PS/CTAB system. The results of Differential Scanning Calorimetry (DSC) confirmed that the glass transition temperature of all the nanocomposites was higher as compared to neat polystyrene. The nanocomposites having 2% of TBAB modified clay showed better oxygen barrier performance as compared to polystyrene.     

Enhanced corrosion prevention effect of polysulfone–clay nanocomposite materials prepared by solution dispersion

A series of polymer–clay nanocomposite (PCN) materials containing polysulfone (PSF) and layered MMT clay were successfully prepared by effectively dispersing inorganic nanolayers of MMT clay in an organic PSF matrix via a solution dispersion technique. The synthesized PCN materials were subsequently investigated with a series of characterization techniques, including Fourier transform infrared (FTIR) spectroscopy, wide‐angle powder X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The prepared PCN coatings with low clay loading (1 wt %) on cold‐rolled steel (CRS) were found to be superior in corrosion prevention to those of bulk PSF, based on a series of electrochemical measurements of corrosion potential, polarization resistance, corrosion current and electrochemical impedance spectroscopy (EIS) in a 5 wt % aqueous NaCl electrolyte. The effects of material composition on the molecular barrier, mechanical strength and optical clarity of PSF and PCN materials, in the form of membranes, was also studied by molecular permeability analysis (GPA), dynamic mechanical analysis (DMA) and UV‐Visible transmission spectra, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 631–637, 2004     

The effect of organoclay on the mechanical properties and morphology of injection‐molded polyamide 6/polypropylene nanocomposites

Nanocomposites containing a thermoplastic blend and organophilic layered clay (organoclay) were produced by melt compounding. The blend composition was kept constant [polyamide 6 (PA6) 70 wt % + polypropylene (PP) 30 wt %], whereas the organoclay content was varied between 0 and 10 wt %. The mechanical properties of the nanocomposites were determined on injection‐molded specimens in both tensile and flexural loading. Highest strength values were observed at an organoclay content of 4 wt % for the blends. The flexural strength was superior to the tensile one, which was traced to the effect of the molding‐induced skin‐core structure. Increasing organoclay amount resulted in severe material embrittlement reflected in a drop of both strength and strain values. The morphology of the nanocomposites was studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy‐dispersion X‐ray analysis (EDX), and X‐ray diffraction (XRD). It was established that the organoclay is well dispersed (exfoliated) and preferentially embedded in the PA6 phase. Further, the exfoliation degree of the organoclay decreased with increasing organoclay content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 175–189, 2004     

Investigation of nanostructure and properties of aromatic–aliphatic polyamide‐based nanocomposites with clay additives

Aromatic–aliphatic polyamide/clay nanocomposites were produced using solution intercalation technique. Surface modification of the clay was performed with ammonium salt of aromatic diamine and the polyamide chains were produced by condensation of 4‐aminophenyl sulfone with sebacoyl chloride (SCC) in dimethyl acetamide. Carbonyl chloride endcapped polymer chains were prepared by adding extra SCC near the end of polymerization reaction. The nanocomposites were investigated for organoclay dispersion, water absorption, mechanical, and thermal properties. Formation of delaminated and intercalated nanostructures was confirmed by X‐ray diffraction and TEM studies. Tensile strength and modulus improved for nanocomposites with optimum organoclay content (8 wt %). Thermal stability and glass transition temperatures of nanocomposites increased relative to pristine polyamide with augmenting organoclay content. The amount of water uptake for these materials decreased as compared with the neat polyamide. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of screw rotation speed on the properties of polystyrene/organoclay nanocomposites prepared by a twin‐screw extruder

We discuss the effect of screw rotation speed on the mechanical and rheological properties and clay dispersion state of polystyrene (PS)/organoclay (clay) nanocomposites prepared by melt compounding with a counterrotating‐type twin‐screw extruder. Poly(styrene‐co‐vinyloxazolin) (OPS) was used as an additional material. The Young's modulus of the PS/OPS/clay nanocomposites showed the maximum value at a screw rotation speed of 70 rpm in this study. This implied the existence of an optimized screw rotation speed for the melt compounding of the polymer/clay nanocomposites. For PS/clay systems without the addition of OPS, the peak intensity from clay increased and the distance between clay platelets in the nanocomposites decreased with the screw rotation speed. On the other hand, inverse results were obtained for PS/OPS/clay systems. According to the transmission electron microscopy photographs, the PS/OPS/clay nanocomposite at 70 and 100 rpm had fully exfoliated clay platelets. The dynamic rheological properties of the PS/clay nanocomposites were almost the same as those of neat PS. On the other hand, the storage and loss moduli of the PS/OPS/clay nanocomposites at the same frequency were larger than those of the PS/clay system. On the whole, the bonding between clay platelets and PS was important for increasing the viscosity and elasticity in the melts of the PS/clay system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1165–1173, 2006     

Morphology,thermal and mechanical behavior of polypropylene nanocomposites toughened with poly(ethylene‐co‐octene)

Rubber‐toughened polypropylene (PP) nanocomposites containing organophilic layered silicates were prepared by means of melt extrusion at 230 °C using a co‐rotating twin‐screw extruder in order to examine the influence of the organoclay and the addition of PP grafted with maleic anhydride (PPgMAH) as a compatibilizer on the morphological, mechanical and thermal properties. The mechanical properties of rubber‐toughened polypropylene nanocomposites (RTPPNCs) were studied through tensile, flexural and impact tests. Scanning electron microscopy (SEM) was used for investigation of the phase morphology and rubber particles size. X‐ray diffraction (XRD) was employed to characterize the formation of nanocomposites. The thermal properties were investigated by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The dynamic mechanical properties were examined by using dynamic mechanical analysis (DMA). From the tensile and flexural tests, the optimum loading of organoclay in RTPP was found to be 6 wt%. The optimum loading of PPgMAH, based on the tensile and flexural properties, was also 6 wt%. The increase in the organoclay and PPgMAH content resulted in a severe embrittlement, manifested by a drop in the impact strength and tensile elongation at break. XRD studies revealed that intercalated RTPPNCs had been successfully prepared where the macromolecular PP segments were intercalated into the interlayer space of the organoclay. In addition, the organoclay was dispersed more evenly in the RTPPNC as the PPgMAH content increased. TGA results revealed that the thermal stability of the RTPPNC improved significantly with the addition of a small amount of organoclay. Copyright © 2006 Society of Chemical Industry     

Polyolefin‐based nanocomposite: The effects of processing aids

PP/organoclay nanocomposites were prepared using different processing aids (EMCA and PPG), and their effects on the thermal and mechanical properties were evaluated by WAXD, TEM, SEM, DSC, and mechanical tests. This study helps to clarify the effects of processing aids on the organoclay surface and on the intercalation and exfoliation processes. Nanocomposites with elongated intercalated and partially exfoliated structures were obtained, mainly when C‐15A was used. The results for the mechanical properties showed that the processing aids increased the impact strength significantly (up to three times that of neat PP) but reduced the flexural modulus of PP nanocomposites. PPG, which is polar promoted wetting MMT surface, thus increasing its interlayer distance, mainly for PP/C‐20A nanocomposites. However, it reduced the interfacial adhesion between the clay and the matrix. Nanocomposites impact strength was improved, especially when the C‐15A organoclay was used, while were achieved better results with the C‐20A organoclay when EMCA was used. The larger the amount of processing aid added, the higher the impact strength, but the lower the flexural modulus of the nanocomposites. PPG caused debonding of the clay particles and increased the number of microvoids, generating more mechanisms to aid in the energy dissipation of the systems. EMCA promoted debonding of clay particles with the formation of fibrils, indicating stronger interactions between the clay and matrix. A slight nucleation effect for PP crystallization was observed, mainly when EMCA was used. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Photo‐oxidation of polystyrene/clay nanocomposites under accelerated UV exposure: Effect on the structure and molecular weight

The present work investigates the effects of photo‐oxidation under accelerated UV conditions on the structure, the molecular weight and the morphology of polystyrene (PS)/organophilic montmorillonite (OMMT) at various clay contents: 2.5, 5, and 7 wt %. Fourier transform infrared spectroscopy, viscosimetry and scanning electron microscopy were used to evaluate the extent of degradation of nanocomposite samples in comparison with neat PS, up to 216 h of exposure. The study has shown that the formation rates of both carbonyl and hydroperoxide groups increase with exposure time, being much higher for PS/OMMT nanocomposites. Moreover, it is also observed that all samples exhibit a large increase in the scission index, however less pronounced for neat PS. These results clearly indicate the formation of low molecular weight products that could arise from chain scission. Further, the photo‐oxidation rate seems to be more affected by the presence of clay, which acts as a catalyst, rather than by the variation of clay contents. Finally, the degraded materials exhibit eroded surface. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel POBD‐modified organoclay and its polyimide nanocomposites for removal of the Co(II) ion

An organophilic clay has been obtained via cation exchange reaction between sodium montmorillonite and the hydrochloride salt of 2‐(5‐(3,5‐diaminophenyl)‐1,3,4‐oxadiazole‐2‐yl)pyridine, POBD. Thermogravimetric analysis (TGA) showed that thermal decomposition of the organophilic clay starts at about 350°C, which shows that it is quite thermally stable compared with conventional montmorillonite modified with aliphatic long chain surfactants. POBD‐modified organoclay almost quantitatively removed the Co(II) ion from aqueous solution at pH = 10.0 (Q_t = 3.00 mg g⁻¹, R = 98.2%). A series of polyimide/clay nanocomposite materials (PCNs) consisting of POBD and benzophenone‐3,3′,4,4′‐tetracarboxylic dianhydride, BTDA were also prepared by an in situ polymerization reaction via thermal imidization. POBD‐modified organoclay was used as a surfactant at different concentrations. Intercalation of polymer chains within the organoclay galleries was confirmed by WXRD. Both the glass transition temperature and thermal stability are increased with respect to pristine PI at low clay concentrations. At high clay loadings, the aggregation of organoclay particles results in a decrease in T_g and thermal stability. In the SEM images of PCN 1 and 3%, too many micro cracks are observed in the background, and a flower‐shape pattern spreads uniformly over the entire surface. The maximum Co(II) uptake capacity and efficiency were observed at pH 10.0 within a 40‐h period for both PI and PCN films. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Preparation and characterization of poly(butylene terephthalate) nanocomposites with various organoclays

Layered‐silicate‐based polymer–clay nanocomposite materials were prepared depending on the surface modification of montmorillonite (MMT). Nanocomposites consisting of poly(butylene terephthalate) (PBT) as a matrix and dispersed inorganic clay modified with cetyl pyridinium chloride (CPC), benzyl dimethyl N‐hexadecyl ammonium chloride, and hexadecyl trimethyl ammonium bromide by direct melt intercalation were studied. The organoclay loading was varied from 1 to 5 wt %. The organoclays were characterized with X‐ray diffraction (XRD) to compute the crystallographic spacing and with thermogravimetric analysis to study the thermal stability. Detailed investigations of the mechanical and thermal properties as well as a dispersion study by XRD of the PBT/clay nanocomposites were conducted. X‐ray scattering showed that the layers of organoclay were intercalated with intercalating agents. According to the results of a differential scanning calorimetry analysis, clay acted as a nucleating agent, affecting the crystallization. The PBT nanocomposites containing clay treated with CPC showed good mechanical properties because of intercalation into the polymer matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Comparative studies on the corrosion protection effect of DBSA-doped polyaniline prepared from in situ emulsion polymerization in the presence of hydrophilic Na-MMT and organophilic organo-MMT clay platelets

A series of polyaniline (PANI)/Na⁺-montmorillonite (MMT) clay and PANI/organo-MMT nanocomposite materials have been successfully prepared by in situ emulsion polymerization in the presence of inorganic nanolayers of hydrophilic Na⁺-MMT clay or organophilic organo-MMT clay with DBSA and KPS as surfactant and initiator, respectively. The as-synthesized Na⁺-PCN and organo-PCN materials were characterized and compared by Fourier transformation infrared (FTIR) spectroscopy, wide-angle powder X-ray diffraction (XRD) and transmission electron microscopy (TEM).Na⁺-PCN materials in the form of coatings with low loading of Na⁺-MMT clay (e.g., 3 wt.%, CLAN3) on cold-rolled steel (CRS) were found much superior in corrosion protection over those of organo-PCN materials with same clay loading based on a series of electrochemical measurements of corrosion potential, polarization resistance, corrosion current and impedance spectroscopy in 5 wt.% aqueous NaCl electrolyte. The molecular weights of PANI extracted from PCN materials and neat PANI were determined by gel permeation chromatography (GPC) with NMP as eluant. Effects of material composition on the gas permeability, optical properties and electrical conductivity of neat PANI and a series of PCN materials, in the form of free-standing film, solution and powder-pressed pellet, were also studied by gas permeability analyzer (GPA), ultraviolet-vis spectra and four-point probe technique, respectively.     

Polystyrene nanocomposite materials by in situ polymerization into montmorillonite–vinyl monomer interlayers

A different series of new polystyrene–clay nanocomposites have been prepared by grafting polymerization of styrene with vinyl‐montmorillonite (MMT) clay. The synthesis was achieved through two steps. The first step is the modification of clay with the vinyl monomers, such as N,N‐dimethyl‐n‐octadecyl‐4‐vinylbenzyl‐ammonium chloride, n‐octadecyl‐4‐vinylbenzyl‐ammonium chloride, triphenyl‐4‐vinylbenzyl‐phosphonium chloride, and tri‐n‐butyl‐4‐vinylbenzyl‐phosphonium chloride. The second step is the polymerization of styrene with different ratios of vinyl‐MMT clay. The materials produced were characterized by different physical and chemical methods: (1) IR spectra, confirming the intercalation of the vinyl‐cation within the clay interlayers; (2) thermogravimetric analysis (TGA), showing higher thermal stability for PS–nanocomposites than polystyrene (PS) and higher thermal stability of nanocomposites with of phosphonium moieties than nanocomposites with ammonium moieties; (3) swelling measurements in different organic solvents, showing that the swelling degree in hydrophobic solvents increases as the clay ratio decreases; (4) X‐ray diffraction (XRD), illustrating that the nanocomposites were exfoliated at up to a 25 wt % of organoclay content; and (5) scanning electron microscopy (SEM), showing a complete dispersion of PS into clay galleries. Also, transmission electron microscopy (TEM) showed nanosize spherical particles of ～ 150–400 nm appearing in the images. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3739–3750, 2007