Properties of a reactive‐graphitic‐carbon‐nanofibers‐reinforced epoxy

Our previous studies showed that herringbone graphitic GNFs surface‐derivatized with reactive linker molecules bearing pendant primary amino functional groups capable of binding covalently to epoxy resins. Of special importance, herringbone GNFs derivatized with 3,4′‐oxydianiline (GNF‐ODA) were found to react with neat butyl glycidyl ether to form mono‐, di‐, tri‐, and tetra‐glycidyl oligomers covalently coupled to the ODA pendant amino group. The resulting reactive GNF‐ODA (butyl glycidyl)_n nanofibers, r‐GNF‐ODA, are especially well suited for reactive, covalent incorporation into epoxy resins during thermal curing. Based on these studies, nanocomposites reinforced by the r‐GNF‐ODA nanofibers at nanofiber loadings of 0.15–1.3 wt% were prepared. Flexural property of cured r‐GNF‐ODA/epoxy nanocomposites were measured through three‐point‐bending tests. Thermal properties, including glass transition temperature (T_g) and coefficient of thermal expansion (CTE) for the nanocomposites, were investigated using thermal mechanical analysis. The nanocomposites containing 0.3 wt% of the nanofibers gives the highest mechanical properties. At this 0.3‐wt% fiber loading, the flexural strength, modulus and breaking strain of the particular nanocomposite are increased by about 26, 20, and 30%, respectively, compared to that of pure epoxy matrix. Moreover, the T_g value is the highest for this nanocomposite, 14°C higher than that of pure epoxy. The almost constant change in CTEs before and after T_g, and very close to the change of pure epoxy, is in agreement with our previous study results on a chemical bond existing between the r‐GNF‐ODA nanofibers and epoxy resin in the resulting nanocomposites. POLYM. COMPOS., 28:605–611, 2007. © 2007 Society of Plastics Engineers     

Surface‐activated nanosilica treated with silane coupling agents/polypropylene composites: Mechanical,morphological, and thermal studies

This work reports the mechanical, morphological, and thermal properties of the polypropylene (PP) nanocomposites containing nanosilica (nano‐SiO₂) which were treated by different functional group silane coupling agents. Four types of silane coupling agents namely aminopropyltriethoxy silane (APTES), glycidyloxypropyltrimethoxy silane (GPTMS), trimethoxysilylpropyl methacrylate (TMPM), and dichlorodimethyl silane (DCMS) were used to modify the surface‐activated nanosilica. To enhance the effectiveness of the coupling, nanosilica was chemically activated and analyzed through FTIR and X‐ray photo electron spectroscopy (XPS). The highest tensile strength was recorded by the activated nanocomposites treated with APTES followed by nanocomposite treated with GPTMS, TMPM, and DCMS, respectively. The addition of silane coupling agents into nano‐SiO₂/PP system further improved the tensile modulus of the PP nanocomposites. From the transmission electron microscopy (TEM) analysis, activated nanosilica treated with APTES showed better nanosilica dispersion in the PP matrix and lesser agglomeration occurred when compared with the other silane coupling agents which were used in this study. Surface activation process does not effectively increase the degree of crystallinity and thermal stability on the PP nanocomposites. However, with the assistance of the surface treatment, it was found that the thermal behavior of the PP nanocomposites had been enhanced. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Study of morphological and mechanical performance of amine‐cured glassy epoxy–clay nanocomposites

The effect of three different alkylammonium‐modified montmorillonite on morphological and mechanical properties of glassy epoxy‐amine nanocomposites is reported. Small amounts of clays <10 phr (part per hundred of resin) were used in each system of nanocomposite. The morphology of the prepared nanocomposites was performed by means of X‐ray diffraction and transmission electron microscopy. Differential scanning calorimetry (DSC) was used to investigate the glass transition temperatures (T_g). Mechanical properties were based on tensile characteristics (Young's modulus), impact strength, and fracture toughness. The measured moduli were compared to theoretical predictions. Scanning electron microscopy was used to study the morphological structure of the fracture surfaces of impacted specimens. It was found that at a low content of 2 phr (1.2 wt %) of nanoclays, the impact strength and the fracture toughness were improved by 77 and 90% respectively, comparatively to the neat epoxy, whereas DSC revealed a reduction of the T_g of nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermophysical properties of anhydride‐cured epoxy/nano‐clay composites

Polymer nano‐composites made with a matrix of anhydride‐cured diglycidyl ether of bisphenol A (DGEBA) and reinforced with organo‐montmorillonite clay were investigated. A sonication technique was used to process the epoxy/clay nano‐composites. The thermal properties of the nano‐composites were measured with dynamic mechanical analysis (DMA). The glass transition temperature T_g of the anhydride‐cured epoxy was higher than the room temperature (RT). For samples with 6.25 wt% (4.0 vol%) of clay, the storage modulus at 30°C and at (T_g + 15)°C was observed to increase 43% and 230%, respectively, relative to the value of unfilled epoxy. The clay reinforcing effect was evaluated using the Tandon‐Weng model for randomly oriented particulate filled composites. Transmission electron microscopy (TEM) examination of the nano‐composites prepared by sonication of clays in acetone showed well‐dispersed platelets in the nano‐composites. The clay nano‐platelets were observed to be well‐intercalated/expanded in the anhydride‐cured epoxy resin system. POLYM. COMPOS., 26:42–51, 2005. © 2004 Society of Plastics Engineers.     

Effect of the filler size and content on the thermomechanical properties of particulate aluminum nitride filled epoxy composites

Polymer matrix composites based on brominated epoxy as the matrix and aluminum nitride (AlN) particles as the filler were prepared. The influences of the size, content, and size distribution of AlN on the thermomechanical properties, including the glass‐transition temperature (T_g), coefficient of thermal expansion (CTE), dynamic storage modulus (E′), dynamic loss modulus (E″), and loss factor (tan δ), of the composites were investigated by thermomechanical analysis and dynamic mechanical analysis. There was a total change trend for T_g; that is, T_g of the composites containing nano‐aluminum nitride (nano‐AlN; 50 nm) was lower than that of the micro‐aluminum nitride (micro‐AlN; 2.3 μm) filled composites, especially at high nano‐AlN contents. The T_g depression of the composites containing nano‐AlN was related to the aggregation of nano‐AlN and voids in the composites. On the other hand, the crosslink density of the epoxy matrix decreased for nano‐AlN‐filled composites, which also resulted in a T_g depression. The results also show that E′ and E″ increased, whereas tan δ and CTE of the composites decreased, with increasing the AlN content or increasing nano‐AlN fraction at the same AlN content. These results indicate that increasing the interfacial areas between AlN and the epoxy matrix effectively enhanced the dynamic modulus and decreased CTE. In addition, at a fixed AlN content of 10 wt %, a low E′ of pre‐T_g (before T_g temperature) and high T_g were observed at the smaller weight ratio of nano‐AlN when combinations of nano‐AlN plus micro‐AlN were used as the filler. This may have been related to the best packing efficiency at that weight ratio when the bimodal filler was used. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis,characterization, and thermo mechanical properties of siloxane‐modified epoxy‐based nano composite

In this study, polymer hybrid composites were synthesized by sol‐gel process. 3‐Amino‐propyltrimethoxysilane [APTMS)/γ‐Glycidoxypropyl trimethoxy‐silane (GPTMS); (4, 4′‐Methylene‐dianiline (DDM)] and 1,4‐Bis(trimethoxysilylethyl) benzene (BTB) were added to DGEBA type epoxy resin for anticipated to exhibit excellent thermal stability. Boron trifluoride monoethylamine (BF₃MEA) was used as catalyst. The structure of nanocomposites was characterized by attenuated total reflectance (ATR) and solid‐state ²⁹Si NMR which suggest EP‐APTMS‐BTB/EP‐GPTMS‐BTB possesses T³; T¹–T⁰, and T¹ structures when the BTB content was lower than 10 wt % and higher 20 wt %, respectively. BF₃MEA was proved to be an effective catalyst for the sol‐gel reaction of APTMS, but it could not promote for GPTMS. From TEM microphotographs, EP‐APTMS‐BTB (10 wt %) possesses a dense inorganic structure (particle size around 5–15 nm) compare with the loose inorganic structure of EP‐GPTM‐/BTB (10 wt %). DSC, TGA were use to analyze the thermal properties of the nanocomposites and DMA was used to analyze the dynamic mechanical properties of hybrid composites. The T_gs of all nanocomposites decreased with the increasing BTB content. A system with BTB content lower than 10 wt % showed good dynamic mechanical property and thermal stability (Td₅ increased from 336°C to 371°C, char yield increased from 27.4 to 30.2%). The structure of inorganic network affects the Td₅ and dynamic mechanical properties of composite. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40984.     

Preparation and properties of bio‐based epoxy montomorillonite nanocomposites derived from polyglycerol polyglycidyl ether and ε‐polylysine

Glycerol polyglycidyl ether (GPE) and polyglycerol polyglycidyl ether (PGPE) were cured with ε‐poly(L ‐lysine) (PL) using epoxy/amine ratios of 1 : 1 and 2 : 1 to create bio‐based epoxy cross‐linked resins. When PGPE was used as an epoxy resin and the epoxy/amine ratio was 1 : 1, the cured neat resin showed the greatest glass transition temperature (T_g), as measured by differential scanning calorimetry. Next, the mixture of PGPE, PL, and montomorillonite (MMT) at an epoxy/amine ratio of 1 : 1 in water was dried and cured finally at 110°C to create PGPE‐PL/MMT composites. The X‐ray diffraction and transmission electron microscopy measurements revealed that the composites with MMT content 7–15 wt % were exfoliated nanocomposites and the composite with MMT content 20 wt % was an intercalated nanocomposite. The T_g and storage modulus at 50–100°C for the PGPE‐PL/MMT composites measured by DMA increased with increasing MMT content until 15 wt % and decreased at 20 wt %. The tensile strength and modulus of the PGPE‐PL/MMT composites (MMT content 15 wt %: 42 and 5300 MPa) were much greater than those of the cured PGPE‐PL resin (4 and 6 MPa). Aerobic biodegradability of the PGPE‐PL in an aqueous medium was ～ 4% after 90 days, and the PGPE‐PL/MMT nanocomposites with MMT content 7–15 wt % showed lower biodegradability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Development of high‐performance epoxy/clay nanocomposites by incorporating novel phosphonium modified montmorillonite

Novel organoclays were synthesized by several kinds of phosphonium cations to improve the dispersibility in matrix resin of composites and accelerate the curing of matrix resin. The possibility of the application for epoxy/clay nanocomposites and the thermal, mechanical, and adhesive properties were investigated. Furthermore, the structures and morphologies of the epoxy/clay nanocomposites were evaluated by transmission electron microscopy. Consequently, the corporation of organoclays with different types of phosphonium cations into the epoxy matrix led to different morphologies of the organoclay particles, and then the distribution changes of silicate layers in the epoxy resin influenced the physical properties of the nanocomposites. When high‐reactive phosphonium cations with epoxy groups were adopted, the clay particles were well exfoliated and dispersed. The epoxy/clay nanocomposite realized the high glass‐transition temperature (T_g) and low coefficient of thermal expansion (CTE) in comparison with those of neat epoxy resin. On the other hand, in the case of low‐reactive phoshonium cations, the dispersion states of clay particles were intercalated but not exfoliated. The intercalated clay did not influence the T_g and CTE of the nanocomposite. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of epoxy content on dynamic mechanical behaviour of PEI‐toughened dicyanate–novolac epoxy blends

By varying the cyanate/epoxy ratio, three polyetherimide(PEI)‐modified bisphenol A dicyanate–novolac epoxy resin blends with different epoxy contents were prepared. The effects of epoxy content on the dynamic mechanical behaviour of those blends were investigated by dynamic mechanical thermal analysis. The results showed that the glass transition temperature of the cyanate–epoxy network (T_g1) in the modified blend decreases with epoxy content. When the epoxy content increases, both the width of the glass transition of the cyanate–epoxy network and its peak density are depressed substantially. Although the tangent delta peak value of PEI is basically independent of epoxy content, the T_g of PEI (T_g2) decreases with epoxy content. T_g1 is independent of the PEI loading. When T_g1 is lower than T_g2, however, the T_g1 in the blend with revised phase structure is substantially lower than other blends. Copyright © 2004 Society of Chemical Industry     

Effects of amino‐functionalized carbon nanotubes on the properties of amine‐terminated butadiene–acrylonitrile rubber‐toughened epoxy resins

Amino‐functionalized multiwalled carbon nanotubes (MWCNT‐NH₂s) as nanofillers were incorporated into diglycidyl ether of bisphenol A (DGEBA) toughened with amine‐terminated butadiene–acrylonitrile (ATBN). The curing kinetics, glass‐transition temperature (T_g), thermal stability, mechanical properties, and morphology of DGEBA/ATBN/MWCNT‐NH₂ nanocomposites were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis, a universal test machine, and scanning electron microscopy. DSC dynamic kinetic studies showed that the addition of MWCNT‐NH₂s accelerated the curing reaction of the ATBN‐toughened epoxy resin. DSC results revealed that the T_g of the rubber‐toughened epoxy nanocomposites decreased nearly 10°C with 2 wt % MWCNT‐NH₂s. The thermogravimetric results show that the addition of MWCNT‐NH₂s enhanced the thermal stability of the ATBN‐toughened epoxy resin. The tensile strength, flexural strength, and flexural modulus of the DGEBA/ATBN/MWCNT‐NH₂ nanocomposites increased increasing MWCNT‐NH₂ contents, whereas the addition of the MWCNT‐NH₂s slightly decreased the elongation at break of the rubber‐toughened epoxy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40472.     

Effects of high nano‐SiO2 contents on properties of epoxy‐modified polybenzoxazine

High‐performance nanosilica composites based on epoxy‐modified polybenzoxazine matrices are developed. Chemorheological study of benzoxazine–epoxy resin mixtures reveals that processing window of the benzoxazine resin (BA‐a) is substantially broadened with an addition of the liquid epoxy. Glass transition temperature (T _g) of the BA‐a copolymerized with epoxy resin shows a synergistic behavior with a maximum T _g value (174°C) at the benzoxazine–epoxy mass ratio of 80:20. The copolymer at this composition is also used as a matrix for nano‐SiO₂ composites. A very low melt viscosity of the benzoxazine–epoxy mixtures promotes good processability with the maximum attainable nano‐SiO₂ loading up to 35 wt%. From scanning electron microscopy investigation, fracture surface of the 35 wt% nano‐SiO₂‐filled benzoxazine–epoxy composite reveals relatively homogeneous distribution of the nano‐SiO₂ in the copolymer with good particle wet‐out. In addition, very high reinforcing effect was also observed in such high content of the nano‐SiO₂, i.e., about 2.5 times in modulus improvement. This improvement is attributed to the strong bonding between the copolymer matrix and the nano‐SiO₂ through ether linkage as confirmed by Fourier‐transform infrared investigation. POLYM. COMPOS., 38:2261–2271, 2017. © 2015 Society of Plastics Engineers     

Free‐volume effects on the thermomechanical performance of epoxy–SiO2 nanocomposites

In this study, free‐volume effects on the thermal and mechanical properties of epoxy–SiO₂ nanocomposites were investigated. SiO₂ particles ranging from 15 nm to 2 µm were used, and the nature of the matrix–filler interphase was modified by surface grafting. Nanoparticles 15 nm in diameter yielded an increase in the glass‐transition temperature (T_g) of the composites up to 5 °C; at the same time, they increased the storage modulus (E′) from 2340 to 2725 MPa. Conversely, large particles markedly decreased both T_g and E′; this suggested the pivotal role of nanoparticle size on the final properties of the nanocomposite. The functionalization of SiO₂ nanoparticles markedly improved their dispersion within the epoxy matrix. The positron annihilation lifetime spectroscopy results indicate that the free volume strongly depended on the interphase. These experimental findings obtained here could be extrapolated to industrially relevant nanocomposites and could provide a rationale for the comprehension of free‐volume effects on the thermal and mechanical properties of nanocomposite materials. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45216.     

Functionalized graphene sheets‐epoxy based nanocomposite for cryotank composite application

Multifunctional high performance functionalized graphene sheets (FGSs) based epoxy nanocomposites were investigated to understand the feasibility that these FGSs‐epoxy nanocomposites can be applied to cryotank composite applications. The FGSs were successfully synthesized from graphite flakes through preparing graphite oxides by oxidizing graphite flakes first and next, thermally exfoliating the formed graphite oxides. These high performance FGSs were next incorporated into epoxy matrix resin system to generate the uniformly dispersed FGSs reinforced epoxy nanocomposites. The resultant FGSs‐epoxy nanocomposites significantly enhanced resin strength and toughness about 30–80% and 200–700% at room and low temperatures of −130°C, respectively, and reduced the coefficient of thermal expansion (CTE) of polymer resin at both below and above T_g about 25% at loading of 1.6 wt% FGSs, and increased T_g of polymer resin about 8°C at low loading of 0.4 wt% FGSs without deteriorating their good processability. We found that these significantly improved properties of FGSs‐reinforced epoxy nanocomposite were closely associated with high surface area and wrinkled structure of the FGSs. The further optimization will result the high performance FGSs‐epoxy nanocomposite suitable for use in the next generation multifunctional cryotank carbon fiber reinforced polymer (CFRP) composite applications, where better microcrack resistance and mechanical and dimensional stability are needed. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Phase separation of poly(ether sulfone imide) modified epoxy resin

Poly(ether sulfone imide)s (PEI) with molecular weight M_n ∼ 10⁴ were synthesized from 3,3′,4,4′-benzophenone tetracarboxylic dianhydride and amine terminated poly(ether sulfone) having molecular weights ranging from M_n ∼ 400 to M_n ∼ 4000. Thus, the PEIs had the same molecular weight but various imide and ether sulfone contents. The PEIs were mixed with a stoichiometric mixture of diglycidyl ether bis-phenol-A (DGEBA)/diamino diphenyl sulfone (DDS). The effect of PEI on the curing reaction of DGEBA/DDS and the morphology of the polymer blend were studied by differential scanning calorimetry (DSC) and optical microscopy. In the DGEBA/DDS/PEI blend with a fixed PEI molecular weight and PEI concentration but with various imide content, the experimental data revealed the PEI with a higher content of ether sulfone had a lower T_g and a better compatibility with solvents and epoxy resins; the curing reaction rate of DGEBA/DDS/PEI was faster for PEI with a higher imide content; the DSC data of cured DGEBA/DDS/PEI showed two T_gs, indicating phase separation between PEI and cured epoxy resins; and the data of optical microscopy showed that the compatibility of PEI with epoxy resins increased with the content of ether sulfone in PEI. © 1996 John Wiley & Sons, Inc.     

Synthesis and properties of polystyrene‐g‐mSiO2 filled polypropylene nanocomposites

Hydrophobically modified nanosilica was prepared from tetraethoxysilane (TEOS) and γ‐methacryloxypropyltrimethoxysilane (MPS) by a two step sol‐gel process. The polystyrene‐grafted‐modified nanosilica (PS‐g‐mSiO₂) hybrid particles were prepared by grafting polystyrene onto the resulting hydrophobically modified nanosilica by dispersion polymerization. The hybrid nanoparticles were subsequently used as the filler to fabricate polypropyrene (PP) nanocomposites. The crystallization kinetics, crystal morphology and crystallization phase component of PS‐g‐mSiO₂/PP nanocomposite were studied using a differential scanning calorimeter (DSC), polarizing optical microscopy (POM) and X‐ray diffraction (XRD). Crystallization half life (t_1/2) decreased, while the Arami exponent (n) of PS‐g‐mSiO₂/PP nanocomposite increased compared with that of virgin PP. A rheological study allowed the unambiguous characterization of the dispersibility of nanosilicas in PS‐g‐mSiO₂/PP nanocomposite. The storage modulus, melt viscosity and the elongation to break of the PS‐g‐mSiO₂/PP nanocomposite were found to be strongly dependent on the grafting of PS on nanosilicas. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Structure and properties of nylon 1010/ethylene‐vinyl acetate rubber–based dynamically vulcanized thermoplastic elastomers filled with SiO2

Dynamically vulcanized Nylon 1010/ethylene‐vinyl acetate rubber (EVM)/SiO₂ nanocomposites were prepared. Maleic anhydride grafted ethylene‐vinyl acetate copolymer (EVA‐g‐MA) and nano‐silica (SiO₂) was used as a compatibilizer and a filler, and silane coupling agent (KH550, 3‐triethoxysilylpropylamine) was used to improve the dispersion of SiO₂ in the nanocomposites. The nanocomposites were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), dynamic mechanical analysis (DMA), differential scanning calorimeter (DSC), and rheology analysis and mechanical properties test. SEM and AFM images showed that the compatibility between Nylon 1010 and EVM was improved by adding the compatibilizer. An increase in SiO₂ content and the addition of the compatibilizer led to an increase in the tensile strength of the nanocomposite. A nanocomposite based on Nylon 1010/EVM/DCP (30/70/0.8) with tensile strength of 16.3 MPa and elongation at break of 180% was obtained by the addition of 15 phr EVA‐g‐MA and 40 phr SiO₂. The non‐isothermal crystallization processes of Nylon/EVM blend were investigated by DSC. It was observed that EVM rubber could act as heterogeneous nuclei for Nylon which was more effective in Nylon/EVM/DCP blend than in Nylon/EVM blend. POLYM. ENG. SCI., 55:581–588, 2015. © 2014 Society of Plastics Engineers     

Simultaneous improvement in strength,toughness, and thermal stability of epoxy/halloysite nanotubes composites by interfacial modification

This work investigated the effect of silane modification of halloysite nanotubes (HNTs) on the mechanical properties of epoxy/HNTs nanocomposites. Three kinds of silane coupling agents, including 3‐(2‐aminoethyl)‐aminopropyltrimethoxysilane (AEAPS), (3‐glycidyloxypropyl)‐trimethoxysilane (GPTMS), and octyltriethoxysilane (OTES), were employed. It was shown that the modified HNTs exhibited a better dispersion in the epoxy matrix compared with pristine one. Because of strong interfacial interaction between AEAPS modified HNTs and the epoxy matrix, the nanocomposites exhibited the highest glass transition temperature and modulus among all the samples. On the other hand, AEAPS and GPTMS modified HNTs/epoxy nanocomposites showed enhanced tensile strength and toughness. The toughing mechanisms were identified by the SEM micrographs of the fracture surfaces of the different kinds of samples. In this study, simultaneous enhancement of strength, toughness, and thermal stability of epoxy by the modified HNTs provides a novel approach to produce high‐performance thermosets. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43249.     

Effect of functionalized SWCNTs on microstructure of PP‐g‐MA/OMMT/f‐SWCNTs nanocomposite

The aim of this work was to study the effect of functionalized single‐walled carbon nanotubes (f‐SWCNTs) on the microstructure of PP‐g‐MA/organic modified montmorillonite (OMMT)/f‐SWCNTs ternary nanocomposite. Pristine SWCNTs were chemically modified by maleic anhydride to improve the interaction between PP‐g‐MA and nanotubes. The dispersion states of OMMT in the different nanocomposites were investigated by wide angle X‐ray diffraction. The morphologies of the nanocomposites were characterized by scanning electron microscopy. Crystallization behaviors of nanocomposites were studied through differential scanning calorimetry and polarizing optical microscopy. Different than the PP‐g‐MA/OMMT binary nanocomposite, in which the OMMT is mainly in an exfoliated state, the ternary PP‐g‐MA/OMMT/f‐SWCNTs nanocomposite exhibits mostly intercalated OMMT. Furthermore, in the ternary nanocomposite, the crystallization of polymer is mainly induced by f‐SWCNTs rather than by OMMT. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphology and mechanical properties of natural rubber latex films modified by exfoliated Na‐montmorillonite/polyethyleneimine‐g‐poly (methyl methacrylate) nanocomposites

Na‐montmorillonite/polyethyleneimine‐g‐poly(methyl methacrylate) (Na‐MMT/PEI‐g‐PMMA) nanocomposite latexes were prepared by soap‐free emulsion polymerization in the aqueous suspension of Na‐MMT. The exfoliated morphology of the nanocomposites was confirmed by XRD and TEM. With the aim of improving morphology and mechanical properties of natural rubber latex (NRL) films, the synthesized Na‐MMT/PEI‐g‐PMMA nanocomposites were mixed with NRL by latex compounding technology. The results of SEM and AFM analysis showed that the surface of NRL/Na‐MMT/PEI‐g‐PMMA film was smoother and denser than that of pristine NRL film while Na‐MMT was dispersed uniformly on the fracture surface of the modified films, which suggested the good compatibility between NRL and Na‐MMT/PEI‐g‐PMMA. The tensile strength of NRL/Na‐MMT/PEI‐g‐PMMA films was increased greatly by 85% with 10 phr Na‐MMT/PEI‐g‐PMMA when Na‐MMT content was 3 wt % and the elongation at break also increased from 930% to 1073% at the same time. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43961.     

Study on structure and properties of SSBR/SiO2 co‐coagulated rubber and SSBR filled with nanosilica composites

The morphological structure, glass transition, mechanical properties, and dynamic mechanical properties of star‐shaped solution‐polymerized styrene‐butadiene rubber (SSBR) synthesized by a multifunctional organic lithium initiator and SiO₂‐SSBR composite (N‐SSBR) prepared through adding a small amount of nanosilica modified by silane coupling agent to star‐shaped SSBR synthetic solution and co‐coagulating, and their nanocomposites filled with 20 phr nanosilica were investigated, respectively. The results showed that the silica particles were well dispersed with nanosize in N‐SSBR, which glass‐transition temperature (T_g) was 2°C higher than SSBR. N‐SSBR/SiO₂ nanocomposite exhibited lower Payne effect and internal friction loss, higher mechanical properties, and its T_g was 2°C higher than SSBR/SiO₂ nanocomposite. N‐SSBR might promote the dispersion of nanosilica powder in matrix and could be applied to green tire tread materials. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008